Related
So I'm asking here.
Does anyone have phone problems with the GB radio leak/any of the available roms?
I try to place a phone call and get an instant force close along with loss of service for about 30 seconds. I've had this on both das bamf's test build and the debloat rom out there.
I can't find any help or anyone with the same problem. I've wiped and flashed over and over and can't get it to go away.
If no one can help can someone point me in the direction of the most recent radio?
I want to flash that and then load up a froyo backup.
I flashed the GB leak yesterday and I got force closes after ending every phone call and while sending text messages. Its an early release. Still plenty of bugs to be worked out. So no.. your not alone.
restore a backup manually in cwr, download an older radio from the obligatory radio thread (you can mount your sd in cwr) then adb reboot fastboot??? i think... Away you go.
there is a few big threads on this.
i too am jonesin for 2.3, but am waiting for CM7 nightlies, or BAMF. which ever happens first.
You could try the ADB-less way... This is how I flashed GingerJane and it's working.. I get occasional FC's on the phone and the camera is qwirky but as stated above it's an early release.
Flash rom in CWR then batt pull and boot to hboot by holding down power and volume down then install radio.
That's how I did do it. Could anyone point me to the latest radio? At this point I'm just trying to get the latest Froyo radio and then load up one of my backups.
Edit. Sorry I see you found the radio thread. Use .7 combo, first one in the OP if you want latest.
Sent from my ADR6400L using XDA App
Download the radio and ROM you want then... You can just rename the radio properly, boot into hboot and flash it. Then reboot, you will have no service, reboot into Clockwork/Wipe Everything/Flash whatever ROM you want.
No need for adb.
___
Sent from my HTC ThunderBolt 4G LTE.
Okay, I apologize if this thread is posted somewhere else on here, but this is my problem. I have a HTC Thunderbolt, rooted with the new update (1.70.605.0) prevent the frequent reboots. But now that I’ve put the update on there, if I flash a custom rom it automatically removes the update, putting me back with the rebooting issues again. So, to get to the point, is there a way to flash a custom rom but yet keep the new update?
You have to flash a ROM based on that update. Look in the descriptions of the ROM's to find out if it is or not.
I've been looking almost everywhere, and I don't think there's a rom that fits those specs out.
The very action of flashing a ROM is to replace the current one. To give some clarity: there are 3 pieces of software that the phone requires. A radio, hboot, and an OS; usually called a ROM. Your update included a radio which was the reason for the reboots. Any ROM that will work with That radio should yield performance equal to or better than what you have.
I'm sorry I'm kinda new to this all that's why I seem kinda lost. But basically all I need to do, is put the root in, den flash the radio that came with the update?
I'm sorry i worded that all wrong. The only thing that the rom with the update comes with is, busybox and deodexed. It also comes with the 1.70.605.0 radio. Say if i flashed the thunderbolt rom in my phone. After installing it, will it do away with that radio and update or will it remain in there. If not, if i flashed the updated radio with the thunderbolt rom will it pretty much be the same as the update and keep me from having unwanted reboots?
Radios are not included with a ROM. Only the kernel and the ROM change when you flash a ROM.
ROM's are flashed in recovery, Radio's are flashed from the root of your SD card using HBOOT. You get to hboot by powering off your phone, or just do a battery pull, then hold the Volume down button while powering on the phone.
Just make sure that the radio can be used on the ROM. The original post of any ROM thread will list the recommend radio(s) to use.
Sent from my ADR6400L using XDA Premium App
Okay, thanks for all the help. Last question, after the putting a rom in with the ota update in. I flashed to another rom, but once i did that the ota update was no longer there, so i tried the update while running the custom rom and it wouldnt go through leaving me withe the old ota. is there a way to still put the update on after flashing?
Oh, fuuuu...crap.
I may have screwed up here. I rooted my device using Revolutionary, and then using ROM Manager installed the latest Synergy mod on my stock (unrooted Froyo) Thunderbolt. Everything loaded fine, it seemed to be flawless ... but after the update I'm not getting any signal at all. I figured this was a radio issue, so I downloaded the latest radio that was leaked (the 2.11.605 one), put it on my SD card, and flashed that. It said it was "updating" the radio (RADIO_V2), but still no luck. I've tried a few different versions, and although it seems to "flash" and update fine, there's still no signal. Not 1x, 3g, or 4g. Nada. :-\
According to HBOOT, "RADIO" is 1.16.00.0223r, if that helps.
Any ideas on how I can basically undo all this, or have I spectacularly failed at this?
-BT7
bandtrumpet7 said:
Oh, fuuuu...crap.
I may have screwed up here. I rooted my device using Revolutionary, and then using ROM Manager installed the latest Synergy mod on my stock (unrooted Froyo) Thunderbolt. Everything loaded fine, it seemed to be flawless ... but after the update I'm not getting any signal at all. I figured this was a radio issue, so I downloaded the latest radio that was leaked (the 2.11.605 one), put it on my SD card, and flashed that. It said it was "updating" the radio (RADIO_V2), but still no luck. I've tried a few different versions, and although it seems to "flash" and update fine, there's still no signal. Not 1x, 3g, or 4g. Nada. :-\
According to HBOOT, "RADIO" is 1.16.00.0223r, if that helps.
Any ideas on how I can basically undo all this, or have I spectacularly failed at this?
-BT7
Click to expand...
Click to collapse
Well you shouldn't panic. Which radio did you flash? I would flash the MR2 one from this link http://forum.xda-developers.com/showthread.php?t=1154010 . If that doesn't work, I would download the rom directly from Synergy here http://androidfilehost.com/XxXViRuSXxX/roms/synergy/thunderbolt/
From recovery, wipe everything manually (Wipe data/cache/dalvik) than flash the file from where it is on your SD card. If you need specific instructions feel free to ask.
bandtrumpet7 said:
Oh, fuuuu...crap.
I may have screwed up here. I rooted my device using Revolutionary, and then using ROM Manager installed the latest Synergy mod on my stock (unrooted Froyo) Thunderbolt. Everything loaded fine, it seemed to be flawless ... but after the update I'm not getting any signal at all. I figured this was a radio issue, so I downloaded the latest radio that was leaked (the 2.11.605 one), put it on my SD card, and flashed that. It said it was "updating" the radio (RADIO_V2), but still no luck. I've tried a few different versions, and although it seems to "flash" and update fine, there's still no signal. Not 1x, 3g, or 4g. Nada. :-\
According to HBOOT, "RADIO" is 1.16.00.0223r, if that helps.
Any ideas on how I can basically undo all this, or have I spectacularly failed at this?
-BT7
Click to expand...
Click to collapse
Am I reading this right???? You said you rooted with Revolutionary.... Then you flashed some Synergy mod with ROM Manager (always a no-no).... onto your STOCK, UNROOTED FROYO Tbolt???? How did we go from rooted with Revolutionary to stock, unrooted Froyo? I'm confused.
loonatik78 said:
Am I reading this right???? You said you rooted with Revolutionary.... Then you flashed some Synergy mod with ROM Manager (always a no-no).... onto your STOCK, UNROOTED FROYO Tbolt???? How did we go from rooted with Revolutionary to stock, unrooted Froyo? I'm confused.
Click to expand...
Click to collapse
Sure hope he's just confused...
loonatik78 said:
Am I reading this right???? You said you rooted with Revolutionary.... Then you flashed some Synergy mod with ROM Manager (always a no-no).... onto your STOCK, UNROOTED FROYO Tbolt???? How did we go from rooted with Revolutionary to stock, unrooted Froyo? I'm confused.
Click to expand...
Click to collapse
Lol I saw that, I decided not to say anything, I guess you have the sharper tongue than me
Ya pretty scary. I'm hoping he meant he rooted his phone and when he said unrooted, he meant "stock" froyo build on his phone.
Sounds like he is able to boot up, just not get any signal.
I'm guessing he is not too skilled in the ways of Android yet.
Lol just found something interesting. Synergy isn't even on rom manager? I was checking to see if the version ofcsynergy he was using was a previous froyo build, and I can't even find it on rom manager
He probably meant that he used Rom Manager to load the rom rather than using recovery.
haha weird
OK, so I was tired when I wrote my initial post, and I probably didn't make a whole lot of sense. Let me be a bit clearer.
For reference, no, I'm "not too skilled in the ways of Android yet". I've been living with Froyo, anxiously awaiting Gingerbread, and then got fed up and read about all the benefits that come with rooting. Now that an easier method has presented itself - the Revolutionary method, as opposed to opening a command prompt and doing the adb stuff, which I can do - I rooted a friend's phone - but decided to not take the plunge myself - I decided to go ahead and give GB a shot.
So let me break down what happened:
- My phone was unrooted previously, running the same software it came with. I'd done a few OTA updates that Verizon provided but had never gone into my phone. That's why I called it "stock", sorry if that terminology confused people. I just meant it was the OS that came on my phone - Android 2.2 w/ HTC Sense and all that jazz.
- I ran the Revolutionary method posted in the "Thunderbolt Android Development" forum. Worked fine. Ran Recovery and installed Superuser permissions as the documentation said. Worked great. Have a phone where if HBOOT launches, it says -Revolutionary- at the top, and it's got -S OFF. My phone technically is rooted.
- The Synergy mod was also posted in the "TB Android Development" forum. I downloaded that and installed it using ROM Manager (Install ROM from SD). Worked fine ... but then had no signal. Every other aspect of the phone seemed to be working. My radio just wasn't working.
- Downloaded an updated radio from the TB Android Dev. forum, ran that, it said it was updating the radio. Rebooted the phone after the update ... still no signal.
I "solved" this problem by flashing the leaked HTC/TB Gingerbread build, the latest one that was like 400 MB, and when I booted my phone up again I had Gingerbread on my phone with HTC Sense 2.1, and I had signal. So I'm living right now with a fully working phone, but I wanted to dip my foot into custom ROMs. So now I have a backup method just in case the radio thing doesn't work again, but what can I do to install a custom ROM and ensure that I get signal?
Thanks for the response, xebryus - and to everyone else, sorry I was a little confusing. Everybody starts from somewhere, right?
-BT7
Download the GB ROM you want, boot into clockwork (please don't install VIA ROM Manager). In clockwork using you Volume keys to move and the Home button to select....
Select Wipe Data/Factory Reset
Select Wipe Cache
Select Advanced
Select Wipe Dalvik
Select Go Back
Select Mounts and Storage
Select Format /system
Select Go Back Until you are at the first screen
Select Install from SD Card
Select Choose ZIP
Go to the folder where you downloaded the ROM
Select ROM
Select Yes.
When it is done Reboot.
Enjoy!
Sent from my SHIFTAO5P using XDA App
Hey, at least you didn't brick your phone, so kudos for you for getting that far.
As others have stated there are basically two kinds of radio versions out there. One that work with Froyo builds and ones that work with GB builds.
So depending on the rom you are loading, you just have to make sure you have the right radio to match the rom(the rom thread should tell you what radio it requires). From what you were saying, it sounded like you just had the wrong radio.
Anyways, couple of things you want to make sure you do. Any check to make sure the checksum is correct on the radio (so that it's not corrupt) otherwise you could have some major issues. Also, once you flash the radio and you get your phone back up, make sure to either rename or delete the PG05img file from your SD root, otherwise, again a major hassle.
Check out the noob thread at the top of this forum also. It has great info there that will help you on your journey.
Good Luck.
I have always felt more in control flashing from recovery or hboot but I'm curious why no rom manager?
Sent from my Tbolt running Das Bamf 3.0...
RevosFTS said:
I have always felt more in control flashing from recovery or hboot but I'm curious why no rom manager?
Sent from my Tbolt running Das Bamf 3.0...
Click to expand...
Click to collapse
When the TB first came out, it seemed that people were having issues with using rom manager to flash roms (alot of force closes, things in general not working correctly). So many experienced people said to use recovery rather than rom manager to flash anything on the TB.
I guess that idea just kinda stuck after that.
Ok thanks. I will still use recovery anyhow I am more used to it. Plus I'm kinda old school I love adb haha
Sent from my ADR6400L using XDA App
I have downloaded Synergy Rom and have no problems except that I am not able to get the radio to flash. I am on verizon and chose the MR3.5 radio. I did a battery pull and then pressed the power and volume down button to enter HBoot but I do not have an option to Upgrade. What am I doing wrong any help is appreciated. I need help quick, thanks!!!
1more thing when i am in the HBoot window my only options are Fastboot, Recovery, Factory Reset, Simlock, Hboot USB, System Info, Image Crc..... it says radio is 1.16.00.0402w.
Does this mean the radio was already upgraded. Why can I not get a signal then?
Did you rename the .zip and have it on the root of your SD card?
Sent from my ADR6400L using XDA App
HarlyFan said:
1more thing when i am in the HBoot window my only options are Fastboot, Recovery, Factory Reset, Simlock, Hboot USB, System Info, Image Crc..... it says radio is 1.16.00.0402w.
Does this mean the radio was already upgraded. Why can I not get a signal then?
Click to expand...
Click to collapse
Nope..402w is still MR1. Sounds like you are already in bootloader so at this point if it isn't updating then more than likely the file is named incorrectly as stated above.
Radios HAVE to be named PG05IMG.zip (3rd character is a ZERO, not the letter "O"). It HAS to be in the root folder of your SD card. Now, turn the phone OFF.
Next, hold down the VOL-DOWN button. Keep it held down. Is it still held down ? If so, push and hold down the POWER button. When the screen turns on, you can release both. This menu will automatically look for 3 or 4 files with certain names. One of the names (files) it looks for is .... PG05IMG.zip. When/if it finds it, it will check it and ask you if you want to load it. Tell it to load it and then leave your phone alone. It will update it and reboot like normal (if successful).
So I was using the BeastMod ROM for a while and decided to go back and do a recovery and use the stock ROM for a while. I got everything all going back to normal with the stock ROM and got a notification about the T-Mobile Wi-Fi calling update that was available. I downloaded the update and then proceeded to install the update. When the phone reboots it pops to the Android and Triangle screen and does nothing.
Any ideas what to do to get this installed?
CStites said:
So I was using the BeastMod ROM for a while and decided to go back and do a recovery and use the stock ROM for a while. I got everything all going back to normal with the stock ROM and got a notification about the T-Mobile Wi-Fi calling update that was available. I downloaded the update and then proceeded to install the update. When the phone reboots it pops to the Android and Triangle screen and does nothing.
Any ideas what to do to get this installed?
Click to expand...
Click to collapse
You have the stock recovery installed?
You'll probably lose root by installing this update. Just so you know.
I installed the stock recovery, went through the set up of the phone like it was brand new and got a prompt to download. Downloaded, and went through install only to come up with the triangle screen upon reboot of phone. I have to pull battery and restart phone.
I realize that it is possible that losing Root is there. I am just having issues with the operation of the phone and want to run stock. I don't mind sense, my only complaint and only initial want for a new ROM was to get rid of the bloatware.
I have not followed up with the ROM and their development in the last two months or so, so do not where there are and the stability of them. I want something that isn't going to take me all day to install on my phone by trying to figure out how to install it and flashing of kernals and other things. I'd prefer to be able to download to and SD card and install the zip through recovery and that be it. Not sure if that is possible.
CStites said:
I installed the stock recovery, went through the set up of the phone like it was brand new and got a prompt to download. Downloaded, and went through install only to come up with the triangle screen upon reboot of phone. I have to pull battery and restart phone.
I realize that it is possible that losing Root is there. I am just having issues with the operation of the phone and want to run stock. I don't mind sense, my only complaint and only initial want for a new ROM was to get rid of the bloatware.
I have not followed up with the ROM and their development in the last two months or so, so do not where there are and the stability of them. I want something that isn't going to take me all day to install on my phone by trying to figure out how to install it and flashing of kernals and other things. I'd prefer to be able to download to and SD card and install the zip through recovery and that be it. Not sure if that is possible.
Click to expand...
Click to collapse
After you flashed CWM recovery, you are very much can flash Rom and theme from recovery by downloading onto your sdcard - as you so wished - with the exception of Faux's kernal
'Til now, we only have 2 kernel: Stock and Faux's and very much all the Roms are based on stock kernel, so, if you referred to avoid the hassle of using your PC - then stay with stock. You'll only need to flash it once and after that, either upgrading or changing a new rom (stock kernel based) you won't have to flash it again .
Exceptions are:
Beside one or two Roms that featured Faux's kernel (can't recalled exactly but very few - read the first post of your would-be Rom), other than that you will have to pay attention to Xboarder latest Rom - the BulletProof. It's latest version (2.2.0) feature Faux's kernel whereas older version based on stock, so, if you flash older BulletProof Version (2.1.0 and backward) you are worry-free to switches from many Roms without being near your PC to flashing kernel.
I'm strongly encouraged you to go ahead and try some Rom, they are very stable and fast. Battery hog is the thing of the past IMHO
hi,
I am sorry if this is a dumb question. But i have failed several attempts while shifting to ICS (RC 5 by team-nyx). Every time when i install ROM & kernel via CWM and boot the device (vibrant t959) it freezes on the screen with VIBRANT and SAMSUNG displaying WHITE on BLACK back ground.
i have gone back to JFD and tried several times BUT same result.
I was on froyo 2.2 (build UVKB5) updated via kies and did it but no luck. I followed wiki.cyanogenmod.com/wiki/Samsung_Vibrant:_Full_Update_Guide and did starting from No. 03 --
downloaded Cmenard's Kernel with the ClockworkMod Recovery 2.5
Heimdall Suite 1.3.2 for windows
AND upto No. 9 under Windows ONLY: section
the CWM installs as it says (A blue transfer bar will appear on the phone showing the kernel being transferred. The device will reboot automatically. )
after that i cleared factory, cache and dalvik cache.
then I select install Zip from SD card and chose the ROM (which is from team-nyx.com/index.php/releases).
after 3% it says rebooting and vibrant shuts down and reboots.. when after I clicked the combo (vol+vol-power) to enter the CWM its not there.. so I reinstall using [heimdall flash --kernel zImage] command in PC's cmd. then after i redid the same to select from SD and then ROM installed ok.
then I selected the kerenel which was taken by same source and installation went normal..
after I select reboot from CWM it reboots and hangs on vibrant screen.
I cannot figure OUT WHAT IM doing WRONG..
Please HELP ME..!!!
thank you for your time
I am moving to 2.2 via kies after going back to stock JFD. then i will root my vibrant. after that i will install ROM manager from market. THEN i will try to FLASH to ICS RC 5 + kernel from nyx TEAM.
I dont know what is wrong.. please HELP
From what you told us it sounds right. Have you tried a different ICS rom? Give ICS slim a try. When you Odin back did you checked re-partition?
Sent from my SGH-T959 using Tapatalk 2
You should try flashing the Gingerbread bootloaders using Odin after you flash back to stock. Those bootloaders can run a Froyo ROM as well as ICS so it wouldn't hurt to do either way. After you flash the bootloader then try flashing the ROM.
And try a different ROM like iwillkillyou suggested. Slim is good, but ICZen is very solid if you're tipping your toes into ICS.
iwillkillyou said:
From what you told us it sounds right. Have you tried a different ICS rom? Give ICS slim a try. When you Odin back did you checked re-partition?
Sent from my SGH-T959 using Tapatalk 2
Click to expand...
Click to collapse
hi,
thank you for the reply. No i havent tried a different ROM. yes I checked repartiton when ODin Y this is happening.. I have Flashed this ROM once.. but then when someone calls me they cudnt hear me clearly.. when i initiate the call its ok.. so I moved back to JFD..:/
kaiser_bun said:
You should try flashing the Gingerbread bootloaders using Odin after you flash back to stock. Those bootloaders can run a Froyo ROM as well as ICS so it wouldn't hurt to do either way. After you flash the bootloader then try flashing the ROM.
And try a different ROM like iwillkillyou suggested. Slim is good, but ICZen is very solid if you're tipping your toes into ICS.
Click to expand...
Click to collapse
thank you for the reply.. I jz finished Updating to 2.2 via kies..ok I will flash Gingerbread bootloaders using Odin. I will try I think it wont be necessary to ROOT the vibrant..to Flash Bootloaders.. I am going to Flash the ICS ROM via ROM manager (after rooting via SuperOneclick root2.3.3)..
haarsh said:
thank you for the reply.. I jz finished Updating to 2.2 via kies..ok I will flash Gingerbread bootloaders using Odin. I will try I think it wont be necessary to ROOT the vibrant..to Flash Bootloaders.. I am going to Flash the ICS ROM via ROM manager (after rooting via SuperOneclick root2.3.3)..
Click to expand...
Click to collapse
Just so that you know, everytime you are using Kies, you are running the risk of hardbricking your device. It is notorius for that and in fact someone last week got HBricked with it.
I don't use ROM Manager and probably won't as long as I have a Vibrant. All you need to do is go back to JFD and pull the CWR from my signature and put it on your internal_sd and label it as Update.zip. Then boot into recovery and hit Reinstall PAckages (might have to do this twice) and your stock recovery (blue) will go to CWR (green) and you can flash away.
Also for more detailed instructions, se my ICS install giude also in my signature.
Woodrube said:
Just so that you know, everytime you are using Kies, you are running the risk of hardbricking your device. It is notorius for that and in fact someone last week got HBricked with it.
I don't use ROM Manager and probably won't as long as I have a Vibrant. All you need to do is go back to JFD and pull the CWR from my signature and put it on your internal_sd and label it as Update.zip. Then boot into recovery and hit Reinstall PAckages (might have to do this twice) and your stock recovery (blue) will go to CWR (green) and you can flash away.
Also for more detailed instructions, se my ICS install giude also in my signature.
Click to expand...
Click to collapse
Thank you for the links.. I downloaded and place CWR inside SD. Without kies can we install official releases via Odin.. is there any way.. im sorry if that is a stupid question
No stupid questions. That is why we are here. I am pretty sure there is a flashable 2.2 stock floating aroung here. I personally don't have it though. Custom 2.2's are at this point tweaked so completely out, that they will blow the doors off any 2.2 stock ROM out there. I usggest Moped_Ryder's ROMs and Fishman's Bionix-redux ROMs. Quality, fast and stable. Not ICS, but everything works and no fear of the dreaded Encryption Bug.
PM incoming btw.
Woodrube said:
No stupid questions. That is why we are here. I am pretty sure there is a flashable 2.2 stock floating aroung here. I personally don't have it though. Custom 2.2's are at this point tweaked so completely out, that they will blow the doors off any 2.2 stock ROM out there. I usggest Moped_Ryder's ROMs and Fishman's Bionix-redux ROMs. Quality, fast and stable. Not ICS, but everything works and no fear of the dreaded Encryption Bug.
PM incoming btw.
Click to expand...
Click to collapse
thank you. btw can we Flash to 2.2 via CWM .. directly selecting the ROM from SD .. without Odin
If you can find it, you should be able to. Just put on your card and flash away, taking care to wipe accordingly.
A note on flow though:
2.1, 2.2 -can go into and out of any 2.2 there is laterally.
2.3-4.0 -will need to Odin to stock before going back to a 2.2 ROM. Can move laterally from 4.0 to 4.0 though.
(i.e DO NOT try to restore a 2.2 nandroid or flash a 2.2 ROM when you are on an ICS variant. the /system is completely changed and reformatted. You need to Odin to get it back.)
Moped Ryder uploaded a semi tweaked version of the stock 2.2 build. It's a zip that you can just flash using CWR:
http://forum.xda-developers.com/showthread.php?t=1674519
It comes rooted with busybox and some other goodies, but it's the stock kernel and whatnot. I'd highly recommend Fishman's Bionix-V Mod or Moped Ryder's Slim_Ryder ROMs if you're going to be on Froyo though. They're both great, but I went with Fishman's latest Bionix Mod since I couldn't get bluetooth to work on Moped Ryder's ROM. Which is really unfortunate because I loved Moped Ryder's otherwise.
And you don't have to Odin back to stock if you're just bouncing around Froyo or Eclair builds; only if you're coming from Gingerbread or ICS (2.3 or 4.0).
Keep us updated. I'm curious to see what worked. It's probably the gingerbread loaders. But, who knows.
Sent from my SGH-T959 using Tapatalk 2
Is your Samsung Vibrant (T959) Rooted.?
iwillkillyou said:
Keep us updated. I'm curious to see what worked. It's probably the gingerbread loaders. But, who knows.
Sent from my SGH-T959 using Tapatalk 2
Click to expand...
Click to collapse
hi.. I tried again with flashing semaphore kernel through Odin installed CWM version higher than 2.5 to install ICS RC5 by nyx --sorry i need that soo badly so didnt checked anything else ..
@that time I was on vibrant 2.2 UVKB5 (stock)
NOT rooted
I didnt had so called
bootloaders
Click to expand...
Click to collapse
(i dunno what it means though--have to search )
BUT it didnt worked for me instead freezes at Vibrant start-up screen. So i Couldnt switch back to CWM. I Odin back to JFD with repartition clicked and my vibrant was locked (network lock). Finally, I got it cleared by application named Galaxy_S Unlock by Helroz from the market.
Now I am at the very beginning again. I am now on 2.1 JFD. I dont know WHY this happening to me .. :crying:
gonna try again with GB bootloaders.. BUT Im sick of failing and going back to 2.1 (my friends who are having captivate had no problem)
Speedy5150 said:
Is your Samsung Vibrant (T959) Rooted.?
Click to expand...
Click to collapse
At the time i was trying it was NOT rooted.. But now i have it rooted because i needed to unlock the network . which happened me for the very first time after flashing back to JFD using Odin..
Thank you guys for the links and thoughts on 2.2 ROMs.. I am not that expert . Thats why i was updating to 2.2 via KIES -- which is not a good idea as it seems with the ability 2 brick the device. I am going to get Bionix-V FishmanMod V4 FULL and install as http://forum.xda-developers.com/showthread.php?t=1441976 says..
It says Boot into clockwork recovery and i think i found something to do that in this thread http://forum.xda-developers.com/showthread.php?t=734164
I have to get ROM manager from market and go through it..
BUT Im damn upset with the RC5 ICS update by nyx being unable to installed into my device.. I will try with GB bootloaders flashed ..
If you are going to go with Fish's ROM, then all you need to do is Odin back to JFD and pull the CWR from my signature and put it on your internal_sd and label it as Update.zip. Then boot into recovery and hit Reinstall Packages (might have to do this twice) and your stock recovery (blue) will go to CWR (green) and you can flash away.
Fish also has a Odin package that you can flash his ROM through Odin and not have to deal with CWR.
ROM Manager is no longer supporting 2.1, so if you do go back to JFD, then it will be hard to get RM. It is out there somewhere but really all you need is the Update.zip from above to do it. I suggest that you stay on Fish's ROM for awhile and read about ICS installs and all the little things that are involved. If you do flash Fish's ROM, you don't need to mess with the bootloaders.
Btw, aside from Kies, messing with Bootloaders is one of the sure fire ways to hardbrick your device. It only takes seconds to flash them, but do it wrong and, well you know.
Good luck and ask if you have any.
Woodrube said:
If you are going to go with Fish's ROM, then all you need to do is Odin back to JFD and pull the CWR from my signature and put it on your internal_sd and label it as Update.zip. Then boot into recovery and hit Reinstall Packages (might have to do this twice) and your stock recovery (blue) will go to CWR (green) and you can flash away.
Fish also has a Odin package that you can flash his ROM through Odin and not have to deal with CWR.
ROM Manager is no longer supporting 2.1, so if you do go back to JFD, then it will be hard to get RM. It is out there somewhere but really all you need is the Update.zip from above to do it. I suggest that you stay on Fish's ROM for awhile and read about ICS installs and all the little things that are involved. If you do flash Fish's ROM, you don't need to mess with the bootloaders.
Btw, aside from Kies, messing with Bootloaders is one of the sure fire ways to hardbrick your device. It only takes seconds to flash them, but do it wrong and, well you know.
Good luck and ask if you have any.
Click to expand...
Click to collapse
thanks alot for the info brother.. some guys told me STUPID.. but YOU guys are awesome.. I am a newbie to this flashing and stuff.. but learned a lot from XDA . Thanks again for the reply. now I have stock 2.1 with ROOT . (rooted cuz i had to unlock the vibrant). I will flash to Fish's 2.2 ROM soon. BTW may i ask you after moving to Fish's ROM and later if i need to move to ICS still can I do it without messing with Bootloaders..
Thank you
That is what we are here for in the Q&A/General sections.
Regaring your question about Gingerbread bootloaders being needed:::Yes and No.
Gingerbread bootloaders were required in the infancy of ICS ROMs bc they prevented what is called "Rainbows" in your clockwork where you couldn't see anything. The options were there but you just couldn't see them. Then as ICS evolved, the need for GB bl's lessened and now you don't need them at all.
But...There's always a but...Gingerbread bl's are recommended by most of the devs for ICS builds because they seem to work better with the custom recoveries that come with some of the kernels. There is more to it but in short, GB bl's are not required but recommended.
If you go to my ICS install guide, in the middle pages and more again at the end, Yosup (highly respected user) and I have a detailed conversation about bootloaders and their installation. Once he got over the fear and did it, he was hooked and flashing ICS ROMs weekly if not more. It is a very informative section of that thread.