Atrix - GingerBlur to CherryBlur = Failed To Boot 4! - Atrix 4G Q&A, Help & Troubleshooting

Hi There
I was using GingerBlur on my Atrix until I decided to go ahead and try out CherryBlur.
I downloaded the MEGA pack as suggested by the developer, booted into CWM recovery, "Installed zip from SD card".
After about 2-3 minutes, it said: Installation Successful.
From the menu options, I chose, Reboot.
From then on, I cant boot my phone. It just says, "Failed To Boot 4" and goes into RSD mode.
I cant get it to fastboot or anything.
Question:
Which SBF do I flash now? I heard flashing too old an SBF can hard brick my phone because apparently later versions of Android set a fuse somewhere on the phone?
Could please someone help me by telling WHICH sbf will save me here?

Go to gitbrew.org/atrix and download the 1.8.3, it should be near the top of the list as it is a popular download.
Sent from my MB860 using XDA App

chillax1 said:
Hi There
I was using GingerBlur on my Atrix until I decided to go ahead and try out CherryBlur.
I downloaded the MEGA pack as suggested by the developer, booted into CWM recovery, "Installed zip from SD card".
After about 2-3 minutes, it said: Installation Successful.
From the menu options, I chose, Reboot.
From then on, I cant boot my phone. It just says, "Failed To Boot 4" and goes into RSD mode.
I cant get it to fastboot or anything.
Question:
Which SBF do I flash now? I heard flashing too old an SBF can hard brick my phone because apparently later versions of Android set a fuse somewhere on the phone?
Could please someone help me by telling WHICH sbf will save me here?
Click to expand...
Click to collapse
As long as you are not on Gingerbread OTA you can flash back to 1.83. Really shouldnt be trying to flash roms if your bootloader is still locked. most of the roms out now need unlocked bootloader and the unlocked CWM.
Gingerblur was a pseudo-Rom, didnt mess with anything important, Alien, cherry, and aura are for unlocked bootloaders using the CWM version for unlocked bootloaders.

Thanks a lot for your reply
I was waiting for someone to reply before trying to flash again using RSDLite..
I had 4.1.83 OTA when I installed GingerBlur..
Can I flash to the stock ROM (4.5.91) provided here:
http://forum.xda-developers.com/showthread.php?t=1163342
Or should it be some other version, say 4.1.83, as you suggested?
And then how do I go about unlocking the bootloader? I am sorry, but I am a newbie to all this...!!
Thanks again!

I flashed the 1.8.3 sbf using rsd lite then I used kennethpenn's update to go to gingerbread. you can find it here: forum.xda-developers.com/showthread.php?t=1163342
2 things:
*be sure you unlock the bootloader before doing this update*
and
*when you click on the download link on xda it takes you to the bottom of a briefmobile page, scroll up to the download link that says "beta 4.5" under it, and download that one... otherwise you'll get a failed to boot (i did this by mistake).*

Great so almost all believe that 1.8.3 should be safe as far as I did not do an OTA for 2.3.4 (which I did not, it was only until 4.1.83)
I will try flashing the 1.8.3 on the weekend, about 24 hours from now
I have my fingers crossed!

failed to boot 4 issue happen when you flash a boot.img in your phone without unlockimg the bootloader, i know... i had it...

Got it back to life!
Thanks everyone guys...

Related

[Q] How to unlock AT&T Atrix 4g bootloader

Hey i have At&t Motorola Atrix, i Want to unlock my boot loader. My phone is running 2.3.4(OTA), webtop version 1.2.0-110,build number 4.5.91 and kernel 2.6.32.9 and more over i rooted my phone . i read so many threads and in the end im so confused and i dont know from where to start. can you help me ?
http://forum.xda-developers.com/showthread.php?t=1202883
Sent from my MB860 using XDA App
im getting error when i click on start button it says failed to flash
You cannot get all the info you need in one post, search through the thread and look to see if anyone else is having your issue.
Here is another thread that offer up some links that might help too.
http://forum.xda-developers.com/showthread.php?t=1154600
You will have to read a little bit. It would take a very long time for someone to compile a tutorial that would include all the variables that might be relative to this phone.
usman.daud said:
im getting error when i click on start button it says failed to flash
Click to expand...
Click to collapse
usman.daud said:
Hey i have At&t Motorola Atrix, i Want to unlock my boot loader. My phone is running 2.3.4(OTA), webtop version 1.2.0-110,build number 4.5.91 and kernel 2.6.32.9 and more over i rooted my phone . i read so many threads and in the end im so confused and i dont know from where to start. can you help me ?
Click to expand...
Click to collapse
I can confirm that flashing the latest sbf from pudding will work on 2.3.4 OTA, using RSD lite. After flashing the sbf, you will get a 0x1000 cannot boot message, but don't worry, its not a real hard brick. When that message pops up, IMMEDIATELY go into fastboot and type "fastboot oem unlock" and you will not be bricked, and you will be unlocked. I performed this on my 2.3.4 OTA atrix yesterday, without any problems.
where u get latest Sbf file ? when i click start for flashing it gave error that flashing process failed
and also have u tired any custom rom ? and how was the experience
http://forum.xda-developers.com/showthread.php?t=1182526
use that sbf file. it works on 2.3.4 OTA.
read through the thread - it will explain well what to expect, explain the soft brick issue and how to remedy it, and also what you need to have in advance for it to all work smoothly.
MY RSD give error. when i entered in RSd support rsdlite show it connected when i start sbf flashing it give error that flashing process failed.0x7027 phone cant retrieve any help with that ?.
try using this version of RSDLite. It worked for me with this one.
http://forum.gsmhosting.com/vbb/archive/t-1229831.html
im previously on 5.3.1 is safe to use a downgraded version
yeah.
its just a different version of the pc software. downgrading is only a problem if you're downgrading phone software but this is ok.
not working
Same error? Did you check that the drivers installed correctly? Try a reboot on pc and use a different usb port

[Q] bricked once..let's not do it again. 4.1.83 @ 2.2.2

I bricked one Atrix already a few weeks ago, and have since gotten another...(don't wanna think about it)..
I had toyed with unlocking it, and 'rooted' using the gingerbreak method. I was then, bored, one day and installed CWM paid version(Since I had it on my Nexus One, and it popped up under 'my apps'). Out of curiosity I installed the bootloader via CWM, thinking it would fail before it broke anything..wrong.. It froze after a reboot, but after taking the battery out and back in came back up. Didn't think any more about it, and figured i'd finish the unlocking/flashing part some other time..
Meanwhile the annoying pending system update kept going off, and I inadvertently clicked download... it downloaded, so I figured might as well install and not worry about roms since with root I was able to use the google adhoc wifi apk, which is what I care about most. The install was stuck in an infinite loop. It would 'fail to load RSD', if you took the battery out it boot to android then reboot automatically for system update over and over. I tried using the RSD lite program at this point to flash back to stock rom, and ended up hard bricked...
So, forgive me for being a complete noob as I never had an issue with my nexus one. I am at 4.1.83, android 2.2.2. and baseband 1.7.15.. Which of the many tutorials and post should I follow? How safe are they? Did I brick because I had a partial 2.3.x install, and flashed back to a pre 2.3 base? I've read many post, but definitely a bit gun shy of bricking another Atrix. The phone keeps bugging me to update, and I keep hitting 'cancel'.
I'd like to unlock the boot loader for custom roms.
I'm also a heavy linux user, majority of tutorials seem to only imply windows with RSD lite? can this not be done with adb, and fastboot via linux?
http://forum.xda-developers.com/showthread.php?t=1154600
I would personally go HERE Read through the entire post, then read it again. And go with the ATT 2.3.4 pudding+root
That of course is after reading and re-reading THIS post! (also linked in the post above mine.
Just my opinion.. and make sure you read and nkow what to expect!
xploited said:
http://forum.xda-developers.com/showthread.php?t=1154600
Click to expand...
Click to collapse
That references 4.5.91 and unless I missed it, doesn't explicitly state it's backwards compatible with 4.1.83 and 2.2.2. is it?
Should I update first, to be at those levels and just know not to flash to an earlier build(pre 2.3.4/4.5.91)?
jmorgan6 said:
That references 4.5.91 and unless I missed it, doesn't explicitly state it's backwards compatible with 4.1.83 and 2.2.2. is it?
Should I update first, to be at those levels and just know not to flash to an earlier build(pre 2.3.4/4.5.91)?
Click to expand...
Click to collapse
Nope, don't update. It's safer to unlock BL while you are still at 4.1.83, you just need to download the correct unlock file from the pudding thread.
Otherwise the unlocking steps are exactly the same.
The easiest steps to unlocking are here:
http://briefmobile.com/how-to-unlock-the-atrix-4g-bootloader
From there you can flash CWM in one minute.
From there you can flash any rom via CWM in two minutes.
Good luck and don't do anything stupid.

[Q] Need help updating rooting phone to gingerbread!!!!!!

Wow I’m really drained I’ve spent a lot of hours trying to update to gingerbread (OTA) but just can’t get anything to work.
My phone Atrix 4G currently running build OLYFR_U4_1.8.3, the phone is rooted and has the webtop hack.
What I have tried so far
I have tried to flash the spf file using RSD lite with the new gingerbread update. No luck about 10 min in the program stops and says flash failed . I tried using RSD lite to flash back to an earlier version again same problem flash fails .
I have tried the over the air update and it failed; I got the yellow triangle, when I got the yellow triangle I swiped the bottom of the screen and it said DockService.apk failed, so I searched and found numerous people saying I had to revert back to the orginal files if I did the webtop hack. I reverted back to the orginal files using super manager but now my DockService.apk, PhonePortal.apk, and DockProvider.apk all say (no install); it looks like this:
DockService.apk(no install)
I tried installing the apk files using super manager and it attempts to but fails .
I’m really at a loss here I have no idea what to try anymore this is just really kicking my butt, could someone please help me or point me in the right directions. Thank you in advance.
are you trying to unlock your bootloader? or just upgrade?
Have you tried flashing the pudding SBF?
I had a problem with the update and originally flashed the Fruit Cake img files using fastboot. Maybe that will work. Look for the Fruit Cake Thread in the Dev section, or try the pudding SBF..
bamastang said:
Have you tried flashing the pudding SBF?
I had a problem with the update and originally flashed the Fruit Cake img files using fastboot. Maybe that will work. Look for the Fruit Cake Thread in the Dev section, or try the pudding SBF..
Click to expand...
Click to collapse
thats why I asked if he wanted to unlock the bootloader.
He can't use pudding if doesn't want to unlock
I just want to upgrade.
your best bet would be flashing back to 1.8.3 stock and then trying to upgrade
bamastang said:
Have you tried flashing the pudding SBF?
I had a problem with the update and originally flashed the Fruit Cake img files using fastboot. Maybe that will work. Look for the Fruit Cake Thread in the Dev section, or try the pudding SBF..
Click to expand...
Click to collapse
I saw the fruit cake thing last night, but I’m confused how to use it.
I know I see an option for fastboot when I turn the phone on holding the power and down volume button but that’s where my knowledge ends, can you tell me or point to a thread on how to Fastboot?
I haven’t heard of the pudding SBF I will look more into that now, thanks.
spitefulcheerio said:
your best bet would be flashing back to 1.8.3 stock and then trying to upgrade
Click to expand...
Click to collapse
I have the spf file for 1.8.3 but when i try using RSDlite to flash back it fails??
Is there another way to flash back??
fastboot works in conjunction with the command prompt on your pc. It's much better than rsd
Anyone got any ideas on why in super manager my dockservice, portal, and dockprovider all say no install in the GUI??
Is this going to affect me in anyway?
spitefulcheerio said:
thats why I asked if he wanted to unlock the bootloader.
He can't use pudding if doesn't want to unlock
Click to expand...
Click to collapse
Not true, he can flash pudding and not unlock. I hadn't unlocked for a month or so after I had pudding. It runs fine without running command line oem unlock. ^_^
I had the same problem.
I update my phone successfully only thru my PC.
Download and install automated update tool from motorola support site which will guide you through the update process. This tool will upgrade your device to Android 2.3 (Gingerbread) from any previously released version.
kukupuku said:
I had the same problem.
I update my phone successfully only thru my PC.
Download and install automated update tool from motorola support site which will guide you through the update process. This tool will upgrade your device to Android 2.3 (Gingerbread) from any previously released version.
Click to expand...
Click to collapse
yep tried that too, when i connect my phone the program doesnt read the phone?
so its offical gotten worse now, i dont have any data???
Calls and Wifi do work though.
locke_03 said:
so its offical gotten worse now, i dont have any data???
Calls and Wifi do work though.
Click to expand...
Click to collapse
I'm going to guess this has to do with my files that say (no install)
namely the phone portal one, I believe that controls data
O god let us pray
I believe I'm having the same problem as you. NOTHING WORKS to update this damn thing. I even wiped it.
Mman14 said:
I believe I'm having the same problem as you. NOTHING WORKS to update this damn thing. I even wiped it.
Click to expand...
Click to collapse
Yep I wiped mine too and that didn’t do anything for me.
I ran across some good guides that may help us out:
http://forum.xda-developers.com/showthread.php?t=1139715
http://forum.xda-developers.com/showthread.php?t=1202883
I’m going to try this tonight.
How to unlock bootloader:
http://www.addictivetips.com/mobile/unlock-motorola-atrix-4g-bootloader-on-froyo-gingerbread/
One last link i found, this appears to be the easiest to follow guide I have seen. He even tells you how to install and run the CWM Recovery(tenfar's) which is epic in it's own right.
http://forum.xda-developers.com/showthread.php?t=1167373
After work I am determined to get this dame thing up and running, I will post my results tomorrow. Thanks to everyone for the help.
locke_03 said:
One last link i found, this appears to be the easiest to follow guide I have seen. He even tells you how to install and run the CWM Recovery(tenfar's) which is epic in it's own right.
http://forum.xda-developers.com/showthread.php?t=1167373
After work I am determined to get this dame thing up and running, I will post my results tomorrow. Thanks to everyone for the help.
Click to expand...
Click to collapse
The guide worked perfect for me, easy to follow and straight forward. I am now updated and running the Alien Rom

How to take Motorola Photon 4g out of the grave?

Recently I ordered Motorola 4g from US.... It was with stock Sprint Sunfire OS.
System Version : 45.4.13.MB855.Sprint.en.Us
Model MB855
Android 2.3.5
Baseband N_01.29.10R
Webtop 1.2.0-180
Kernel [email protected] #2
Build 4.5.1A-1_SUN-254_13
So what I did, I was trying to install custom rom on that. Steps I had taken
Rooted phone via installing SuperUser and various rooting methods like ClickOnce, Photon -Torpedo but no one seems successful , while executing I got errors everytime. But after day or two I came to know about that my phone is rooted. As I was getting SuperUser popups on root operations. Then I installed CWM and tried to install the ROM from there but everytime I got stucked at Yellow Triangular icon (recovery mode).
Repeated step on rooting process and unlocking the bootloader by applying pudding.rar and fastboot commands and every time i got the error and Starting RSD Screens, but anyhow my phone recovers itself to its original boot state afetr pulling out battery and manually restrating.
Finally one day I use some other Recovery Tool , i am unable to recall the name. It installed and rebooted successfully in the recovery mode. I then wipe the dalvik cache, wipe factory reset and then tried to installl the custom rom that MIUI 2.68 i think . I was happy to see some designer screens on my phone and then it said rom installed successfully.
I then reboot my phone and found it in the Failed To Start2 , Starting RSD mode
I tried various way to restore...
Installing pudding.rar using RSD lite but everytime I got sec_exception : sec_exception : b655, eddc,eb
I then tried reinstalling SBF : 1FF-sunfire-user-2.3.4-4.5.1A-1_SUN-198_7-CM-release-keys-signed-Sprint-US.sbf and sunfire-2.3.5-4.5.1A-1_SUN-254_4 but while enumerating phone I got error sec_exception febe 4e 4e
I have also tried nopudding4u.sbf but the same result.
Please,, help me and my phone out .. as its going to be more than a week... i feel handicaaped...
Please guide me through the step by step , which file and when and please do provide the links of the files to download.
**Update OTA with 2.3.5 before murdering.....**
Most of those sticky threads are outdated, without important informations. You need to search in whole dev section, there are the answers, how to recover your bricked Photon.
bring it ON..............please
peetr_ said:
Most of those sticky threads are outdated, without important informations. You need to search in whole dev section, there are the answers, how to recover your bricked Photon.
Click to expand...
Click to collapse
Thanks for your reply peetr_.. I would like to know on the basis of my exceptions , Is my phone recoverable or become as useless as a paperweight. I can see fastboot modes and RSD modes and can even swicth between them. In some other forum , I came to know that ,I can reover my phone back but for that I need a locked bootstrap for 2.3.5 and then reflash using the stock sbf.
So could you please tell me how to do that and where to find those files. I am digging XDA Forums and AndroidForum.com past two weeks for the solution...
amitranjan said:
Recently I ordered Motorola 4g from US.... It was with stock Sprint Sunfire OS.
System Version : 45.4.13.MB855.Sprint.en.Us
Model MB855
Android 2.3.5
Baseband N_01.29.10R
Webtop 1.2.0-180
Kernel [email protected] #2
Build 4.5.1A-1_SUN-254_13
So what I did, I was trying to install custom rom on that. Steps I had taken
Rooted phone via installing SuperUser and various rooting methods like ClickOnce, Photon -Torpedo but no one seems successful , while executing I got errors everytime. But after day or two I came to know about that my phone is rooted. As I was getting SuperUser popups on root operations. Then I installed CWM and tried to install the ROM from there but everytime I got stucked at Yellow Triangular icon (recovery mode).
Repeated step on rooting process and unlocking the bootloader by applying pudding.rar and fastboot commands and every time i got the error and Starting RSD Screens, but anyhow my phone recovers itself to its original boot state afetr pulling out battery and manually restrating.
Finally one day I use some other Recovery Tool , i am unable to recall the name. It installed and rebooted successfully in the recovery mode. I then wipe the dalvik cache, wipe factory reset and then tried to installl the custom rom that MIUI 2.68 i think . I was happy to see some designer screens on my phone and then it said rom installed successfully.
I then reboot my phone and found it in the Failed To Start2 , Starting RSD mode
I tried various way to restore...
Installing pudding.rar using RSD lite but everytime I got sec_exception : sec_exception : b655, eddc,eb
I then tried reinstalling SBF : 1FF-sunfire-user-2.3.4-4.5.1A-1_SUN-198_7-CM-release-keys-signed-Sprint-US.sbf and sunfire-2.3.5-4.5.1A-1_SUN-254_4 but while enumerating phone I got error sec_exception febe 4e 4e
I have also tried nopudding4u.sbf but the same result.
Please,, help me and my phone out .. as its going to be more than a week... i feel handicaaped...
Please guide me through the step by step , which file and when and please do provide the links of the files to download.
**Update OTA with 2.3.5 before murdering.....**
Click to expand...
Click to collapse
Should have read around a bit before you attempted all of this. Go to the general and QA section of the photon forums and search the first few pages of each. There will be 5 or 6 different threads with people who have experienced the same problems in which we have completely outlined the steps you would need to take.
Is this what I have to do ????
Acvice said:
Should have read around a bit before you attempted all of this. Go to the general and QA section of the photon forums and search the first few pages of each. There will be 5 or 6 different threads with people who have experienced the same problems in which we have completely outlined the steps you would need to take.
Click to expand...
Click to collapse
Step by step 2.3.5 unbrick:
1)Flash this SBF (http://d-h.st/XGJ). Now you'll have stock 2.3.5 for Electrify. But you need Sprint services (I assume), so you don't stop here. -
Flashing ,Using RSD Lite
Click to expand...
Click to collapse
2) Download bootstrap from DroidX2 forum, and get it working. Of course you need to root your photon first.
3) Flash this ROM (http://forum.xda-developers.com/showthread.php?p=30332325) from bootstrap. Please follow the instructions for this ROM carefully, you don't wanna flash the SBF again.
From bootstrap means - adb fast boot, am i right????/
Click to expand...
Click to collapse
4) Flash 254_13 modules (http://d-h.st/aAi) with bootstrap. you need them.
5) Flash 2.3.5_254_13 sv2 boot, recovery and cdrom image sbf (http://d-h.st/TeB) with RSD Lite.
6) Flash 254_12 libmoto_ril.so (http://d-h.st/BmX) with bootstrap. You don't need to flash the radio SBF.
4) and 6) is not needed, if you install rom 3)
amitranjan said:
Step by step 2.3.5 unbrick:
1)Flash this SBF (http://d-h.st/XGJ). Now you'll have stock 2.3.5 for Electrify. But you need Sprint services (I assume), so you don't stop here. -
2) Download bootstrap from DroidX2 forum, and get it working. Of course you need to root your photon first.
3) Flash this ROM (http://forum.xda-developers.com/showthread.php?p=30332325) from bootstrap. Please follow the instructions for this ROM carefully, you don't wanna flash the SBF again.
4) Flash 254_13 modules (http://d-h.st/aAi) with bootstrap. you need them.
5) Flash 2.3.5_254_13 sv2 boot, recovery and cdrom image sbf (http://d-h.st/TeB) with RSD Lite.
6) Flash 254_12 libmoto_ril.so (http://d-h.st/BmX) with bootstrap. You don't need to flash the radio SBF.
4) and 6) is not needed, if you install rom 3)
Click to expand...
Click to collapse
Im pretty sure thats right. However, I have never faced this problem first hand so i would wait for a second opinion before going forward. Peetr will know, hopefully he will chime in.
Yes. Exactly those steps.
Bootstrap is bootstrap CWM recovery, you must download the apk and install, following the instructions.
peetr_ said:
Yes. Exactly those steps.
Bootstrap is bootstrap CWM recovery, you must download the apk and install, following the instructions.
Click to expand...
Click to collapse
Thanks for the confirmation of the steps.
Few more things:
1. I have still my bootloader locked i think. So will these these steps work.
2. Flash this SBF (http://d-h.st/XGJ). Now you'll have stock 2.3.5 for Electrify. But you need Sprint services (I assume), so you don't stop here. - What If I dont want Sprint Services? I am here in India and there is no sprint network. We have VodaFone, Airtel and Other operators, still on 3G. No 4G here. Can I stop @ 1.
3. Can I install , other custom roms on it, in future If I want?
No cause you will have a photon radio with electrify modules won't work.
Unable to boot into recovery
peetr_ said:
Yes. Exactly those steps.
Bootstrap is bootstrap CWM recovery, you must download the apk and install, following the instructions.
Click to expand...
Click to collapse
I have installed the SBF correctly and too roooted the phone. Also installed the DroidX Bootstrap by Koushik Dutta. but I am unable to boot into recovery. Can I try ClockWorkMod Recovery... that we generally used to flash roms or strictly bootstrap is necessary. I have tried System recovery by Tenfar but it wont boot into recovery...
Please help
It's recovery for DroidX2. Not DroidX.
And you must be connected to wall charger, to boot into it.
Photon is now Electrified with LIFE ----
Thanks a TON to all the Photon Guys, especially peetr_. :highfive::highfive::highfive::highfive::good::good::good::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory::victory: Now my photon and ELECTRIFIED and has a SPRINTing LIFE....
But still I am curious about the custom rom installation.
1. Is it possible and safe or I have to stick with the stock rom.
2. Wait for motorola / sprint for their another update if they allow us to installl custom roms (well its not possible, I know)
You can try some custom roms for locked bootloader. You can always sbf back.
Can you provide me some links for my phone as i am facing some unusual restarts withis rom...
Sent from my MB855 using xda app-developers app
Also i am facing Sleep Of Death issue after waking up this dead phone from grave....
Earlier it was working fine. Generally i face one or two a day.
Is rom upgradation a solution? I hv experienced whenever it goes to sleep the back panel gets heated up than normal. Also when i use wifi 3g the same thing happens...
Sent from my MB855 using xda app-developers app
amitranjan said:
Step by step 2.3.5 unbrick:
1)Flash this SBF (http://d-h.st/XGJ). Now you'll have stock 2.3.5 for Electrify. But you need Sprint services (I assume), so you don't stop here. -
2) Download bootstrap from DroidX2 forum, and get it working. Of course you need to root your photon first.
3) Flash this ROM (http://forum.xda-developers.com/showthread.php?p=30332325) from bootstrap. Please follow the instructions for this ROM carefully, you don't wanna flash the SBF again.
4) Flash 254_13 modules (http://d-h.st/aAi) with bootstrap. you need them.
5) Flash 2.3.5_254_13 sv2 boot, recovery and cdrom image sbf (http://d-h.st/TeB) with RSD Lite.
6) Flash 254_12 libmoto_ril.so (http://d-h.st/BmX) with bootstrap. You don't need to flash the radio SBF.
4) and 6) is not needed, if you install rom 3)
Click to expand...
Click to collapse
This seems like a lot of work just to get a softbricked Photon 4G to work. Didn't Motorola release a soak test about two months ago? Do we have an SBF for that? If so then couldn't someone with a bricked Photon 4G (running 2.3.5 stock) just flash the soak test files and get the Photon working fine?
Also if someone does follow these instructions, will they be able to get the latest OTAs from Sprint when ICS/JB goes official?
sub2k1 said:
This seems like a lot of work just to get a softbricked Photon 4G to work. Didn't Motorola release a soak test about two months ago? Do we have an SBF for that? If so then couldn't someone with a bricked Photon 4G (running 2.3.5 stock) just flash the soak test files and get the Photon working fine?
Also if someone does follow these instructions, will they be able to get the latest OTAs from Sprint when ICS/JB goes official?
Click to expand...
Click to collapse
This is the only way, there is no sbf for the latest soak. And honestly, this process doesnt take very long. If you cant spare an hour to unbrick a phone then people shouldnt be tinkering with their phone in the first place. And nope, you will remain locked, no way to unlock and install ics/jb.
"Say Apple one more MoPho'n time..."
I'm currently struggling with this process. I flashed the .sbf via rsdlite. It gets to 100% but then it says error because phone failed to re-enumerate. I installed RockoDev's ROM last night and phone was bricked all night while I naively thought it would load. Was stuck at the NOW screen when I went to bed and hadn't changed when I woke up.
Acvice said:
And nope, you will remain locked, no way to unlock and install ics/jb.
Click to expand...
Click to collapse
I believe you misunderstood my final question but that is okay.
InsanePostman: Are you also known as huntingoctopus on other sites?
sub2k1 said:
I believe you misunderstood my final question but that is okay.
InsanePostman: Are you also known as huntingoctopus on other sites?
Click to expand...
Click to collapse
I am not. It used to be an old gamer tag that I used for various games. On a side note I still can't get past step 1. Phone fails to re-enumerate after flashing .sbf file.

Motorola atrix 4g stops booting at logo and flashes red light

Hi,
I have a Motorola atrix 4g. The phone will not boot up. It turns on and the Motorola logo come then the red light stars blinking. after a minute or so the phone restarts and repeats the process. I tryed factory hard reset but no luck.
i fount this on the web http://forum.xda-developers.com/showthread.php?t=966405 but has no idea how to do this.
Pleas help me
thank you
Pgeorge
It happens if there is somthing wrong when you install a rom
try to find another rom and flash it if you unlocked the bootloader
or flash ATT 4.5.91 Rom via RSD Lite ONLY IF YOU HAVE LOCKED BOOTLOADER
Jack Krauser said:
It happens if there is somthing wrong when you install a rom
try to find another rom and flash it if you unlocked the bootloader
or flash ATT 4.5.91 Rom via RSD Lite ONLY IF YOU HAVE LOCKED BOOTLOADER
Click to expand...
Click to collapse
hi,
thank you for the fast replay. I have rsd installed, but where can i find this rom
Softbrick
Is bootloader unlocked? Says on m logo?
Sent from my MB860 using xda premium
stevendeb25 said:
Softbrick
Is bootloader unlocked? Says on m logo?
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
It is not unlocked. There is nothing on the logo. Only the m
help
kinggeorge3287 said:
It is not unlocked. There is nothing on the logo. Only the m
Click to expand...
Click to collapse
help please
go here to download any atrix related files
visit that site, it contains everything for the atrix and the best place to get roms, tools, utilities, mods, tweaks, and so forth....
but first download the zip file below this message. I uploaded the zip file for you that has adb, fastboot & moto-fastboot(lets you install .img over 100mb), the necessary dll files & atrix recovery image & command.bat which just opens the command prompt window for you and puts you into the folder so you dont have to navigate anywhere in command prompt to located folders.
first try this, download the zip file, extract to any folder like c:\fastboot
then run the command.bat file to quickly bring up a command prompt and type these commands
Code:
fastboot -w
fastboot flash recovery recovery.img
fastboot reboot
that may solve your issue if your kernel installed properly and the boot.img file was properly written to the boot partition. If it doesn't solve your problem, go to that link above to find the kernel for whatever rom you're on, att, cm7 or cm9. Get the correct kernel thats compatible, pull out the boot.img from that zip file and also place it into your fastboot folder, then go to fastboot mode again and type "fastboot flash boot boot.img" and then fastboot reboot.
android-DEP said:
go here to download any atrix related files
visit that site, it contains everything for the atrix and the best place to get roms, tools, utilities, mods, tweaks, and so forth....
but first download the zip file below this message. I uploaded the zip file for you that has adb, fastboot & moto-fastboot(lets you install .img over 100mb), the necessary dll files & atrix recovery image & command.bat which just opens the command prompt window for you and puts you into the folder so you dont have to navigate anywhere in command prompt to located folders.
first try this, download the zip file, extract to any folder like c:\fastboot
then run the command.bat file to quickly bring up a command prompt and type these commands
Code:
fastboot -w
fastboot flash recovery recovery.img
fastboot reboot
that may solve your issue if your kernel installed properly and the boot.img file was properly written to the boot partition. If it doesn't solve your problem, go to that link above to find the kernel for whatever rom you're on, att, cm7 or cm9. Get the correct kernel thats compatible, pull out the boot.img from that zip file and also place it into your fastboot folder, then go to fastboot mode again and type "fastboot flash boot boot.img" and then fastboot reboot.
Click to expand...
Click to collapse
Hi,
I tryed doing this, but i get a error " Failed to process command flash: recovery error (0x180002)
I think when i tried to flash rom with RSD LIght may have done something to the files. and it was no help. I dont get a flashing red light now. only the phone stops booting at M logo.
Now How do i flash new rome ? Do i use RSD Light or something else. I know that RSB Requires .sbf file but all the files i see in the site you gave me are .zip.
i also tryed the fastboot flash boot boot.img and no luck, it gvies me the error "Failed to process command flash: recovery error (0x180002)"
thank you for the replay
Pgeorge
do you have clockworkmod recovery installed or any custom recovery installed? if not, then thats why it wont flash, your bootloader is locked.
the whole idea behind using clockworkmod recovery is to avoid using RSD to flash sbf files which can brick the phone easily. Its best to avoid using RSD to flash sbf files on your phone at all costs and leave only as a last resort method if you just cannot recover the phone.
Flashing a new rom would normally be done by already having your phone rooted and unlocked with clockworkmod recovery or some other custom recovery installed so you can boot into recovery and choose "install from zip" and point to the zip file that has the rom. The custom recovery does the flashing for you and its a safer method of flashing roms on the phone than RSD.
If you got no other choice and I know what thats like, i been there too. Download RSD Lite v5.6, should be a free download online somewhere, and then search online for "1FF-olympus-user-2.3.6-4.5.141-111212-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P012.sbf", then use RSD to flash that sbf onto phone.
Before trying that, goto http://samcripp.com/files/ and in the folder OTA Updates, download the first file named Blur_Version_91.4.5.141.MB860.ATT.en.US.zip and put it into the fastboot folder, boot into fastboot again and try "fastboot update Blur_Version_91.4.5.141.MB860.ATT.en.US.zip" and you may be able to get away with just using fastboot to flash that update onto the phone to restore corrupt files. I would try this before using RSD to flash the phone
android-DEP said:
do you have clockworkmod recovery installed or any custom recovery installed? if not, then thats why it wont flash, your bootloader is locked.
the whole idea behind using clockworkmod recovery is to avoid using RSD to flash sbf files which can brick the phone easily. Its best to avoid using RSD to flash sbf files on your phone at all costs and leave only as a last resort method if you just cannot recover the phone.
Flashing a new rom would normally be done by already having your phone rooted and unlocked with clockworkmod recovery or some other custom recovery installed so you can boot into recovery and choose "install from zip" and point to the zip file that has the rom. The custom recovery does the flashing for you and its a safer method of flashing roms on the phone than RSD.
If you got no other choice and I know what thats like, i been there too. Download RSD Lite v5.6, should be a free download online somewhere, and then search online for "1FF-olympus-user-2.3.6-4.5.141-111212-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P012.sbf", then use RSD to flash that sbf onto phone.
Before trying that, goto http://samcripp.com/files/ and in the folder OTA Updates, download the first file named Blur_Version_91.4.5.141.MB860.ATT.en.US.zip and put it into the fastboot folder, boot into fastboot again and try "fastboot update Blur_Version_91.4.5.141.MB860.ATT.en.US.zip" and you may be able to get away with just using fastboot to flash that update onto the phone to restore corrupt files. I would try this before using RSD to flash the phone
Click to expand...
Click to collapse
Well i tryed everything you provided, but no luck. I tryed the RSD but it dont go past the M logo after flash. any other way you know?
thnak you
pgeorge
http://forum.xda-developers.com/showthread.php?t=1163342
you said that site doesnt have any SBF files to download, this is a good example of why the owner decided against posting the sbf files online. A lot of people from what I heard, were either soft bricking their phones into temporary hat weights or going full out hard into brick city on a one way ticket joy ride. Flashing sbf files is very risky and RSD tool isn't really meant for the public to be downloading to use at home and flash full roms over their devices. Thats a Motorola utility and it's not exactly a risk-free method of flashing the rom inside these phones. Plus getting SBF files online, you rarely know 100% if its compatible with your model phone or where came from exactly and that it's integrity can be checked for 100% consistency that nothing half-way through the file is missing any chunks of code or is corrupt. Try sticking to only using fastboot & adb & get clockworkmod recovery to make FULL and complete devices backups.
Now that I learned my lesson a few times, no matter what, first thing I always do in recovery is make a backup before I flash anything at all, just in case of just in case, its better to measure twice and cut once.
try that link above and restore stock gingerbread 2.3.4, phone doesnt need to be unlocked or root, and make sure to use "moto-fastboot.exe" it lets you push\pull & install files larger than 200MB onto phone through fastboot, the regular fastboot has some limit on file sizes
Hi,
to give you a update noting worked. The link you provided dont have any working lnks to download. I tryed some other once and no luck. It gave me "failed to boot 1". so i flashed this file "1FF-olympus-user-2.3.6-4.5.141-111212-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P012.sbf" it went away, but no boot after the logo. I don't know what i am doing wrong. Any other ideas?
Thank you
Pgeorge
android-DEP said:
http://forum.xda-developers.com/showthread.php?t=1163342
you said that site doesnt have any SBF files to download, this is a good example of why the owner decided against posting the sbf files online. A lot of people from what I heard, were either soft bricking their phones into temporary hat weights or going full out hard into brick city on a one way ticket joy ride. Flashing sbf files is very risky and RSD tool isn't really meant for the public to be downloading to use at home and flash full roms over their devices. Thats a Motorola utility and it's not exactly a risk-free method of flashing the rom inside these phones. Plus getting SBF files online, you rarely know 100% if its compatible with your model phone or where came from exactly and that it's integrity can be checked for 100% consistency that nothing half-way through the file is missing any chunks of code or is corrupt. Try sticking to only using fastboot & adb & get clockworkmod recovery to make FULL and complete devices backups.
Now that I learned my lesson a few times, no matter what, first thing I always do in recovery is make a backup before I flash anything at all, just in case of just in case, its better to measure twice and cut once.
try that link above and restore stock gingerbread 2.3.4, phone doesnt need to be unlocked or root, and make sure to use "moto-fastboot.exe" it lets you push\pull & install files larger than 200MB onto phone through fastboot, the regular fastboot has some limit on file sizes
Click to expand...
Click to collapse
kinggeorge3287 said:
Hi,
to give you a update noting worked. The link you provided dont have any working lnks to download. I tryed some other once and no luck. It gave me "failed to boot 1". so i flashed this file "1FF-olympus-user-2.3.6-4.5.141-111212-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P012.sbf" it went away, but no boot after the logo. I don't know what i am doing wrong. Any other ideas?
Thank you
Pgeorge
Click to expand...
Click to collapse
when rds end flashing the sbf the phone gets a bootlop or failed to boot error again?
lucamibel said:
when rds end flashing the sbf the phone gets a bootlop or failed to boot error again?
Click to expand...
Click to collapse
it starts up, the M logo comes and it freezes there. To turn the phone off i have to pull the battery.
thank you
Pgeorge
Restore Your Motorola Atrix 4G Back to 4.5.91 Stock Firmware
it helps to remove any problem related to rom..
With so many Android phones literally flooding the market these days, it’s no wonder that there are also so many firmware upgrades and custom firmware being developed and released every now and then. A superior device with great stuff neatly packed into it, the Motorola Atrix 4G is one of the devices for whom developers have devoted significant firmware love.
One reason for the attention that devs give to the Atrix 4G is that it is a fantastic device with a dual-core Nvidia Tegra 2 processor and robust ability for handling impressive graphics and video without choking. Together with its powerful processor and 1 GB of RAM, the Atrix 4G is a mean powerhouse that can be further exploited with the use of third-party applications and custom ROMs.
In an age where technology is constantly changing at an alarming pace it is important to always have a trusted source to get your updates in a timely fashion. Custom ROMs and factory firmware updates have played a crucial role in the development in many of our devices.
For those of you who have rooted your Atrix 4G and already have installed custom ROMs, then you might already have some bad experiences with regards to unofficial firmware sources. Unofficial firmware such as custom ROMs are literally filled with many bugs and disabled features. In many cases, these ROMs are not stable for daily use.
Luckily for owners of the Motorola Atrix 4G, there’s an escape hatch for reverting to stock, functioning firmware and return the phone to its factory state.
In this tutorial, you will learn how to roll back your Motorola Atrix 4G to the official firmware version 4.5.91, regardless of your current firmware
HERE IS THE LINK FOR YOUR PROBLEM....BEST OF LUCK
kinggeorge3287 said:
it starts up, the M logo comes and it freezes there. To turn the phone off i have to pull the battery.
thank you
Pgeorge
Click to expand...
Click to collapse
then you can now try unlocking and flashing cwm recovery and flash a custom rom to avoid using rds again
sikkijazz said:
Restore Your Motorola Atrix 4G Back to 4.5.91 Stock Firmware
it helps to remove any problem related to rom..
With so many Android phones literally flooding the market these days, it’s no wonder that there are also so many firmware upgrades and custom firmware being developed and released every now and then. A superior device with great stuff neatly packed into it, the Motorola Atrix 4G is one of the devices for whom developers have devoted significant firmware love.
One reason for the attention that devs give to the Atrix 4G is that it is a fantastic device with a dual-core Nvidia Tegra 2 processor and robust ability for handling impressive graphics and video without choking. Together with its powerful processor and 1 GB of RAM, the Atrix 4G is a mean powerhouse that can be further exploited with the use of third-party applications and custom ROMs.
In an age where technology is constantly changing at an alarming pace it is important to always have a trusted source to get your updates in a timely fashion. Custom ROMs and factory firmware updates have played a crucial role in the development in many of our devices.
For those of you who have rooted your Atrix 4G and already have installed custom ROMs, then you might already have some bad experiences with regards to unofficial firmware sources. Unofficial firmware such as custom ROMs are literally filled with many bugs and disabled features. In many cases, these ROMs are not stable for daily use.
Luckily for owners of the Motorola Atrix 4G, there’s an escape hatch for reverting to stock, functioning firmware and return the phone to its factory state.
In this tutorial, you will learn how to roll back your Motorola Atrix 4G to the official firmware version 4.5.91, regardless of your current firmware
HERE IS THE LINK FOR YOUR PROBLEM....BEST OF LUCK
Click to expand...
Click to collapse
Hi,
doing this gave me SVF:108:1:2
fail to boot 3
starting rsd mode
lucamibel said:
then you can now try unlocking and flashing cwm recovery and flash a custom rom to avoid using rds again
Click to expand...
Click to collapse
So how do i go about doing this? is there a link i can use?
thank you
Pgeorge
kinggeorge3287 said:
So how do i go about doing this? is there a link i can use?
thank you
Pgeorge
Click to expand...
Click to collapse
help please
kinggeorge3287 said:
help please
Click to expand...
Click to collapse
I am able to get into android recovery. It has a option to update from sdcard. Can i do something with this?
Pleas help
Pgeorge

Categories

Resources