[Q] Endlessly boot loop... - Vibrant Q&A, Help & Troubleshooting

So this phone is really frustrating me...
I tried this method:
http://forum.xda-developers.com/showthread.php?t=849028
I think I make all the step correctly.
1. Installed drivers on my pc.
2. Downloaded 3 files: ODIN, PIT and PDA.
3. Put the Vibrant on Download mode.
4. ODIN detected it, I selected the 2 files... I tried with RePartition check and uncheck...
5. Then hit start, everything runs fine and ODIN indicate PASS.
But... Still boot looping...
When I boot to recovery I have the original recovery (2e).
Can someone help me please? Im really frustrated.
All of this begin because I made a mistake and used a Samsung Galaxy S 4G rom to flash it using ODIN...
I know it has solution because its boot looping.
Best regards,
Omar

I'll link you to some files that may do a better job. I can't tell for sure if you're actually using the right files to flash your phone back to stock or not. Chances are, you're not. Check your messages, and I'll link you to the files in my Dropbox to download.

can you show links here or link me as well. I am having the same problem and i have tried flashing a whole bunch of vibrant roms/kernels but cant stop the phone from boot looping. Thank you.

I would also like to get these files, having the same problem and tried the same methods to fix it and nothing...

Once you got to the point to boot up, did wipe Dalvik, cache and reset first and then try to boot? This is ususally the reason for bootloops.

For some reason I can't get into recovery (holding the 3 buttons) now... I can get to download mode, though.
This phone was bricked and could restore the bootloader with a Riff Box. Now, after the Vibrant screen, the phone turns off.

Related

[Q] Problems with factory reset...

Hi guys:
So I have made so mistakes with this phone. When I got it I thought it was a Samsung Galaxy S 4G...
1. Rooted it using SuperOnClickRoot
2. Almost bricked it triyng to install a CFW done for SGS4G.
Then I realized that it was not a SGS4G and came here looking for some information...
I did that: Return to stock JFD (2.1) using that guide:
http://rootzwiki.com/showthread.php?t=702&p=11409&viewfull=1
And now I am a little more happier because the phone turns on, now the recovery works... But... When it get turn on it boot loop endlessly.
I tried so many times to do the same thing and I don't have a chance to get it fixed. Tried to move an update.zip to the external sd card without luck, I was triying to install ClockworkRecoveryMod.
So now I come here... The phone is boot looping and when Its turning on a lot of line with colors appear...
I know this have solution, just I want to know how to approach it.
Thanks for reading!
Redo the flash back to stock But this time 1st go into recovery and delete the cache then go into the advanced and delete the dalvik.
Then shutdown the phone and re open but this time you want to be in download mode (hold down the volume down only (or could just be the up only)) and on button at the same time to get you there.
Then hook up the phone to your comp after you have Odin up and then reflash stock
Then root> then flash whatever you want from there
good luck
oka1 said:
Redo the flash back to stock But this time 1st go into recovery and delete the cache then go into the advanced and delete the dalvik.
Then shutdown the phone and re open but this time you want to be in download mode (hold down the volume down only (or could just be the up only)) and on button at the same time to get you there.
Then hook up the phone to your comp after you have Odin up and then reflash stock
Then root> then flash whatever you want from there
good luck
Click to expand...
Click to collapse
I just have stock recovery... I don't have Advance button...
I have done it in Download Mode, then connected to Odin (PC), box turn yellow saying COM4 and then selected PDA and PIT file in the guide and hit START.
Everything seems to run fine on ODIN and finalize saying PASS but the phone continue doing the problems I have said in my first post.

[Q] So what kind of brick do I have here?

I was in the process of flashing back to GB in ODIN when it froze on flashing the Modem. Now the phone does nothing. Black screen. Plug USB in and computer doesn't know its there, Download mode will not work, nothing works.
Will a usb jig get it back into download mode so I can try flashing again or is this thing straight gone?
Thanks.
Yes, a USB jig will work.
MultipleMonomials said:
Yes, a USB jig will work.
Click to expand...
Click to collapse
Well I built one and tried it... No go. Nothing happened. Blank screen.
BTW the battery was fully charged right before it bricked so I know the battery isnt dead.
Was the phone on when you plugged it in?
I fixed it. Had to do the Unbrickable Mod. Was a pain in the butt getting the contact pads jumped. Once I got it I was able to get into download mode with the supplied programs and flash back to stock.
Nicely done.
Well I jinxed myself. I went to flash a new ROM and now im stuck on the Samsung Logo. Using the previous method does no good. Just stuck on Sammy logo. I found a different Heimdall One-Click now but it fails to flash Modem and now it vibrates 3 times when the sammy logo is shown.. over and over... so its in a boot loop I take it? If I 3 finger it it shows the stock recovery but I am unable to move up or down in recovery. It just stays on the reboot device selection.. im able to select that with the menu softkey thats it. The vol up and down and power buttons do not respond in recover. Updating the Modem is what started this whole mess for me. When I originally was flashing this the other day ODIN froze on flashing Modem, that put me in a hard brick state requiring me to do the Unbrickable Mod. I got it out of that with ED05 Heimdall Once-Click but since then I have not been able to get it out of this soft brick. My galaxy just wont let me win. :-(
Have you tried using One-Click Resurrector?
MultipleMonomials said:
Have you tried using One-Click Resurrector?
Click to expand...
Click to collapse
Ya, thats how I get it into Download Mode... its the Only way I can get it into download mode actually.
Both Odin and Heimdall are having trouble flashing the phone in windows. Both recognize the phone and connect but will not flash anything. They just sit at uploading PIT/Setting Partitions.
The ED05 Heimdall One-Click in linux flashes the phone with success's accross the board but the phone just sits there on the samsung logo... no vibrating, no recovery, and unable to charge the battery. If I use the EH03 Heimdall One-Click in linux it will flash all the way til it gets to flashing Modem but then fails and the phone is stuck in bootloop on the samsung logo vibrating 3 times over and over. It can also get into the stock recovery but im unable to move up or down the menu. Volume buttons have no effect. The phone will now charge though. Full battery as of right now.
I tried using Odin and Heimdall on another windows computer and they will not move past setting Partitons/uploading PIT either. SO I know there isnt a conflict with my computer.
I would like to try a manual flash in Heimdall Front-End in linux but I have no clue how to install it in Linux. I hate that command line stuff. I guess I have to figure it out though if Im going to try it.
OK, success!
I am now back to stock. I was able to run Heimdall in linux and flash CWM recovery. I was able to get into the recovery and make selections in recovery with the volume buttons. I selected reboot in download. I went to Odin and tried flashing a stock EH03 rom and it worked.... I think the reason I couldnt do that before was because i was holding the power button down to keep it in download mode since that is what is required when in download mode via the unbrickable mod.
The windows based programs must not have liked me holding that power button. Weird. Anyways its working.. now on to getting this thing updated.
im having a similar issue, i can get into cwm, can use download, but when i try using Odin for the stock eh03 it instantly says all threads completed succeeded 0 failed 0. when i reboot in cwm it just takes me to samsung logo wont go any further
Try heimdall.
Ya Heimdall in linux will surely give you a win.

[Q] Samsung Infuse 4g (SGH-i997) stuck at Samsung screen!

I rooted my device with superoneclick, got the 3e recovery, then got the CWM recovery for galaxyS i9000 through ROM manager(working fine), and then rebooted into recovery and flashed carbonROM for 4.2.2 (the .zip file), along with Gapps for 4.2.2. Now it's stuck at the samsung screen, I can't boot into recovery, taking out the battery doesn't help, and the power button is NOT jammed. I can't restore the backup that I made because I can't go into recovery and my computer is not detecting the device (with all the proper drivers installed). I don't know what to do. Does anybody know how to resolve this issue?
I don't care about the user data (including contacts, messages, etc) that much, if it needs to be wiped. I only want my phone back, with or without the ROM.
SirKurry said:
I rooted my device with superoneclick, got the 3e recovery, then got the CWM recovery for galaxyS i9000 through ROM manager(working fine), and then rebooted into recovery and flashed carbonROM for 4.2.2 (the .zip file), along with Gapps for 4.2.2. Now it's stuck at the samsung screen, I can't boot into recovery, taking out the battery doesn't help, and the power button is NOT jammed. I can't restore the backup that I made because I can't go into recovery and my computer is not detecting the device (with all the proper drivers installed). I don't know what to do. Does anybody know how to resolve this issue?
I don't care about the user data (including contacts, messages, etc) that much, if it needs to be wiped. I only want my phone back, with or without the ROM.
Click to expand...
Click to collapse
Are you still able to get into Download mode? If so then you can use Odin to re-flash the stock factory ROM that came with your phone. I would recommend taking a look at this guide here as well as this video guide here.
shimp208 said:
Are you still able to get into Download mode? If so then you can use Odin to re-flash the stock factory ROM that came with your phone. I would recommend taking a look at this guide here as well as this video guide here.
Click to expand...
Click to collapse
the .zip file in the first link is "unavailable in [my] geographical area. I can't use the youtube guide because i can't get into download mode. After not having touched it in several hours, I think the battery ran out, and if I plug it back in, it shows a loading icon that's stuck.
EDIT: I got it to get into download mode, but Odin won't detect it with the COM## thing. I can add the infuse.pit and the PDA md5 thing, but when I start it, it doesn't do anything.
SirKurry said:
the .zip file in the first link is "unavailable in [my] geographical area. I can't use the youtube guide because i can't get into download mode. After not having touched it in several hours, I think the battery ran out, and if I plug it back in, it shows a loading icon that's stuck.
EDIT: I got it to get into download mode, but Odin won't detect it with the COM## thing. I can add the infuse.pit and the PDA md5 thing, but when I start it, it doesn't do anything.
Click to expand...
Click to collapse
Make sure you have the USB drivers for your phone installed, you can download the drivers for your phone from here. Also before you flash anything to your phone it is essential that is has enough battery charge (70%+ to be on the safe side).
Thanks for all the help! I finally got it to detect my device in Odin. Turns out my drivers weren't working properly, so I re-installed them. It's in the process of reverting to stock now. You are a lifesaver!
help
SirKurry said:
the .zip file in the first link is "unavailable in [my] geographical area. I can't use the youtube guide because i can't get into download mode. After not having touched it in several hours, I think the battery ran out, and if I plug it back in, it shows a loading icon that's stuck.
EDIT: I got it to get into download mode, but Odin won't detect it with the COM## thing. I can add the infuse.pit and the PDA md5 thing, but when I start it, it doesn't do anything.
Click to expand...
Click to collapse
can you please tell me how you got it to go into odin. I am stuck at the very same spot.

[Q]Help! Verizon i905 will not boot up.

I know there has been other treads about this before but none of the suggestions seemed to work for me. I searched and searched and I'm just not finding a fix. I hate to do these posts when an easy answer is right there but I just can't figure it out and it's killing me. So here it is:
I just got this Verizon Galaxy Tab that would not come on - only showed the battery charging icon. I just charged it over night and it came on once. However, processes kept shutting down. For instance, when I went into settings and tried to connect to my wifi network, the whole process would just close down. So I let it get to about 40% and reboot it to download mode (there was no recovery). I found the correct .tar file for it and flashed it with ODIN3 v1.85. It completed successfully but now it won't boot past the Samsung splash screen. Once the splash screen comes up, it will just go back to the large battery charging icon in the middle of the screen.
Then I tried the other option where you get into recovery and nothing happens at all. The screen is backlit black (you can just see light around the edges of the screen) and nothing ever happens.
So now, it's just charging but it seems to charge very slowly. I was wondering if this is a battery issue or some strange sequence that needs to be done. It seems to be at about 40% again. Any other suggestions would be appreciated.
These are other things I've tried:
hold the power button down for 30 seconds
Hold the power button down while touching the screen
More suggestions would be appreciated.
Now the tablet is fully charged but it still gets stuck on the splash screen when trying to boot up. Still have no recovery. Also, I'm not able to find a PIT file to re-partition. Can someone tell me how to get the stock recovery back at least? I've been looking but I can't find a file to flash for the recovery.
Same problem
Hi, I have the same issue basically. I have the Galaxy Tab SGH i957D 8.9 (TELUS) and flashed it to root last night, now I have the same problem. Except I have CWM installed, I was able to install that AFTER I locked it up. Help from one of the GURUs here would be great. It's obviously a problem caused by flashing it.
So try flashing with CWM, at least you'll have a good recovery on it. If we work together, we may be able to come up with a solution for our dilemma. I don't believe it;s a major problem, I had the same issue with my captivate phone when trying to CWM and Cyanogenmod, and I got it working perfectly, so there is hope.
I have tried the stock rom, rooted rom, and a couple of others, but still can;t get past the splash screens. Left it overnight trying to boot, and all it did was kill the battery. I can;t even turn it off, it just reboots every time I try shutting down. I CAN get to download and recovery mode though, and flash it all I want with Odin 3.7 and 1.83, just never boots past the splash screens.
DermagraFX said:
Hi, I have the same issue basically. I have the Galaxy Tab SGH i957D 8.9 (TELUS) and flashed it to root last night, now I have the same problem. Except I have CWM installed, I was able to install that AFTER I locked it up. Help from one of the GURUs here would be great. It's obviously a problem caused by flashing it.
So try flashing with CWM, at least you'll have a good recovery on it. If we work together, we may be able to come up with a solution for our dilemma. I don't believe it;s a major problem, I had the same issue with my captivate phone when trying to CWM and Cyanogenmod, and I got it working perfectly, so there is hope.
I have tried the stock rom, rooted rom, and a couple of others, but still can;t get past the splash screens. Left it overnight trying to boot, and all it did was kill the battery. I can;t even turn it off, it just reboots every time I try shutting down. I CAN get to download and recovery mode though, and flash it all I want with Odin 3.7 and 1.83, just never boots past the splash screens.
Click to expand...
Click to collapse
Thanx for the reply. As you can see, I've been around these forums for a long time and usually I'm able to work it out but this one has got me stumped. Just wanted to ask you if you have tried to flash a custom ROM in Clockwork? Also, did you go through unlocking the boot loader befor you flashed it? I did not because I received the tablet in this condition. I tried to flash clockwork mod but I get an "invalid file" error in Odin. Once I flashed the stock recovery and it worked fine. But after reflashing the stock rom, the stock recovery is gone now. Do you have a link to the files you used? I'm thinking that the stock recovery is messed up but I can only find that one file.
no I haven't tried flashing through CWM, as I wasn't trying to flash originally, I was just rooting and going easy on it, then it wouldn't boot, so I wasn't prepared and now can't add files to my SD drive.
I didn't unlock the boot, as none of the instructions I read mentioned it (rooting was all I was trying to do).
I don't even have a stock recovery either, all I have is CWM and TWRP.
I'm going to try mounting it in Linux and see if that makes any difference to put roms on my SD drive, as windows doesn't like it anymore, except through Odin, where luckily it seems to work fine... For now.. lol
Fixed!!!
shawndh said:
Thanx for the reply. As you can see, I've been around these forums for a long time and usually I'm able to work it out but this one has got me stumped. Just wanted to ask you if you have tried to flash a custom ROM in Clockwork? Also, did you go through unlocking the boot loader befor you flashed it? I did not because I received the tablet in this condition. I tried to flash clockwork mod but I get an "invalid file" error in Odin. Once I flashed the stock recovery and it worked fine. But after reflashing the stock rom, the stock recovery is gone now. Do you have a link to the files you used? I'm thinking that the stock recovery is messed up but I can only find that one file.
Click to expand...
Click to collapse
ok.. I have mine fixed and running again.
http://samsung-updates.com/device/?id=SGH-I957D
This is the stock flash/rom for Telus on the SGH i957D LTE 4G 8.9 model. Try samsung-updates.com and search for your exact model and carrier.
-Download correct stock image for your tablet.
-Unpack the file you downloaded
-Put your device in DOWNLOAD mode
-Connect it to Computer
-Start ODIN and wait for the COMM status to show as connected
-In PDA box navigate to your file and add it to the box.
-Press start
-Sit back and relax.
-Enjoy the fireworks as your tablet comes back to life..
-YEAH!!!
Life is good again...
DermagraFX said:
ok.. I have mine fixed and running again.
http://samsung-updates.com/device/?id=SGH-I957D
This is the stock flash/rom for Telus on the SGH i957D LTE 4G 8.9 model. Try samsung-updates.com and search for your exact model and carrier.
-Download correct stock image for your tablet.
-Unpack the file you downloaded
-Put your device in DOWNLOAD mode
-Connect it to Computer
-Start ODIN and wait for the COMM status to show as connected
-In PDA box navigate to your file and add it to the box.
-Press start
-Sit back and relax.
-Enjoy the fireworks as your tablet comes back to life..
-YEAH!!!
Life is good again...
Click to expand...
Click to collapse
I'm glad you got the right firmware and fixed your tab! But this site does not list a firmware for the SCH–i905 anywhere. Unless the Verizon Galaxy tab has an alternate model# there is no firmware on the site for my device. Oh well, at least one of us got tablets fixed. Congrats!
Download mode issue.
What recommendations do you guys have for a tablet that will not recognize in download mode?
I accidently flashed a bootloader and had auto reboot on - couldnt flash kernel and modem in time.
My tablet fully boots up, (rom manager says cwm is installed) as well as when i boot into recovery its completely black.
My main concern is that download mode is not recognized. it was previously working prior to installing the bootloader.
What can i do to fix this issue?
younggunner said:
What recommendations do you guys have for a tablet that will not recognize in download mode?
I accidently flashed a bootloader and had auto reboot on - couldnt flash kernel and modem in time.
My tablet fully boots up, (rom manager says cwm is installed) as well as when i boot into recovery its completely black.
My main concern is that download mode is not recognized. it was previously working prior to installing the bootloader.
What can i do to fix this issue?
Click to expand...
Click to collapse
Can you start by giving as much info as possible about your tab, make model# etc.
can you actually get into download mode? Power button and Volume down button till it boots then release pwr.
you may have bad drivers on your pc. I had this problem with my phone when I installed CM.
get into DL mode and then start Odin and hopefully you will see the Com port attached.
then in PDA load the stock rom for your tab.
hopefully at this point youll be all set.
if your tab is fully functional, then try just flashing CWM or TWPR to your tab. I found with mine that CWM works best. I like TWP better for looks and the touchscreen functionality, but I found it gets a bit flaky after a few flashes, where CWM seems more stable.
SHAWNDH...
give me all your info for your tab, make, model.. carrier etc. as much as you can, and I will see if I can find any stock roms while doing my searches. 2 sets of eyes are better than one...
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
younggunner said:
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
Click to expand...
Click to collapse
I don't get it. First, you can't flash a kernel using Odin. Second, your tab won't even be able to boot without the kernel.
Sent from my GT-P7500 using Tapatalk HD
younggunner said:
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
Click to expand...
Click to collapse
If you can get into DL mode, then its probably just an issue of drivers on your pc. Download the samsung drivers and reinstall.
Then put your tab in dl mode. Then connect to the pc with cable, try a different usb port than before.
Then start odin, if you get the Com port showing up in the status box, then flash CWM recovery to the tab. Then start over with what you are trying to do. But I can almost garantee its an issue with drivers on your pc. I had the exact same problem with my phone when I did it,
and fixing drivers was the issue. I wss stumped for a long time on that issue. If that doesnt work, look into Heimdall flash utility or Kies and go from there.
Hope this helps. Or at least gets you on the right track.
update
DermagraFX said:
If you can get into DL mode, then its probably just an issue of drivers on your pc. Download the samsung drivers and reinstall.
Then put your tab in dl mode. Then connect to the pc with cable, try a different usb port than before.
Then start odin, if you get the Com port showing up in the status box, then flash CWM recovery to the tab. Then start over with what you are trying to do. But I can almost garantee its an issue with drivers on your pc. I had the exact same problem with my phone when I did it,
and fixing drivers was the issue. I wss stumped for a long time on that issue. If that doesnt work, look into Heimdall flash utility or Kies and go from there.
Hope this helps. Or at least gets you on the right track.
Click to expand...
Click to collapse
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
---------- Post added at 12:24 AM ---------- Previous post was at 12:22 AM ----------
younggunner said:
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
Click to expand...
Click to collapse
Ive tried another pc as well. I dont believe its a driver issue as there is 0 interaction in download mode with device manager. but prior it easily was detected in odin no issues.
younggunner said:
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
---------- Post added at 12:24 AM ---------- Previous post was at 12:22 AM ----------
Ive tried another pc as well. I dont believe its a driver issue as there is 0 interaction in download mode with device manager. but prior it easily was detected in odin no issues.
Click to expand...
Click to collapse
Ok... Im getting confused here... You Can still flash with Odin? Then you can install a new recovery on it. If device manager on the pc is not working, then you probably have a corrupt install, or the wrong rom file for your particular tab, and the usb drivers arent correct for your tablet.
Personally, I would start by downloading a stock rom file and return the tab to factory before starting anything, so you have it working as it should before continuing further.
If you DO HAVE a stock rom, maybe you could pass it along, i believe shawndh who started this thread is in need of one for the same tablet.
confusion fixed
DermagraFX said:
Ok... Im getting confused here... You Can still flash with Odin? Then you can install a new recovery on it. If device manager on the pc is not working, then you probably have a corrupt install, or the wrong rom file for your particular tab, and the usb drivers arent correct for your tablet.
Personally, I would start by downloading a stock rom file and return the tab to factory before starting anything, so you have it working as it should before continuing further.
Click to expand...
Click to collapse
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
younggunner said:
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
Click to expand...
Click to collapse
Oh... Well then it is beyond the scope of any problem I have encountered, or seen a solution to. I thought you could still connect in download mode.
Can you change usb debugging mode in tablet settings, that may enable you to connect? If not I dont think I personally can help, as your posts read like you could still use Odin.
On my phone, (galaxy S) nothing would connect after I messed up, but could do things with Heimdalls utility. See if you can connect with that. Worth a try, it does the same as Odin, but connects differently somehow.
DermagraFX said:
Oh... Well then it is beyond the scope of any problem I have encountered, or seen a solution to. I thought you could still connect in download mode.
Can you change usb debugging mode in tablet settings, that may enable you to connect? If not I dont think I personally can help, as your posts read like you could still use Odin.
On my phone, (galaxy S) nothing would connect after I messed up, but could do things with Heimdalls utility. See if you can connect with that. Worth a try, it does the same as Odin, but connects differently somehow.
Click to expand...
Click to collapse
i even went as far as getting a brand new cable to see if it was my cable still same thing. No response in download mode for either pc's ive tried.
little stumped....
possible clues: when tablet boots up, it boots up to a bright black screen, only once it completely boots up am i able to see my display properly.
DermagraFX said:
Can you start by giving as much info as possible about your tab, make model# etc.
can you actually get into download mode? Power button and Volume down button till it boots then release pwr.
you may have bad drivers on your pc. I had this problem with my phone when I installed CM.
get into DL mode and then start Odin and hopefully you will see the Com port attached.
then in PDA load the stock rom for your tab.
hopefully at this point youll be all set.
if your tab is fully functional, then try just flashing CWM or TWPR to your tab. I found with mine that CWM works best. I like TWP better for looks and the touchscreen functionality, but I found it gets a bit flaky after a few flashes, where CWM seems more stable.
SHAWNDH...
give me all your info for your tab, make, model.. carrier etc. as much as you can, and I will see if I can find any stock roms while doing my searches. 2 sets of eyes are better than one...
Click to expand...
Click to collapse
Thanx for the reply. I have the SCH-i905 32gb Galaxy 10.1 tab. The carrier is Verizon. I've spent days looking for another download source but I can only find one - there's a link from this site. Others have posted that it did restore their devices so I'm thinking that there are some bad clusters that need to be quarantined but I can't even find a tool for the Galaxy Tab that will do or check for that. I'd appreciate it if you could take a look though. Thanx.
younggunner said:
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
Click to expand...
Click to collapse
Are you connecting to a USB port that is on the motherboard of your computer? Mine will only recognize my tablet with one port. The other ports are not recognized at all by ODIN.
shawndh said:
Thanx for the reply. I have the SCH-i905 32gb Galaxy 10.1 tab. The carrier is Verizon. I've spent days looking another download source but I can only find one - there's a link from this site. Others have posted that it did restore their devices so I'm thinking that there are some bad clusters that need to be quarantined but I can't even find a tool for the Galaxy Tab that will do or check for that. I'd appreciate it if you could take a look though. Thanx.
Click to expand...
Click to collapse
I don't think its a cluster issue, just a bad flash previously. But you'll see from the link, yours is also known as the P4vzw. Well check the link and make sure that's your tab that I found. Then have a look at ALL the files for that tab.
Have you seen/tried this one... here's the thread STOCK ROM FOR YOUR TAB...
forum.xda-developers.com/showthread.php?t=1342995
Here's just the file.
http://goo.gl/XPMXv
Try flashing CWM recovery to your tab, and try a file from cyanogenmod
http://wiki.cyanogenmod.org/w/P4vzw_Info
Or just try the CM ROM first maybe and see what happens. I don't remember what you have for recovery. There are a bunch on there, but all nightly that I saw, but even that would be better than nothing for now if it works.
I'm still looking, but I know what you're saying about few and far between. I think they all are for the tabs. Let you know if I find anything else.
Another mod ROM. http://www.teamandroid.com/2012/08/...tab-101-sch-i905-android-411-aosp-jelly-bean/

Galaxy Note 10.1 stuck on "Samsung Galaxy Note" screen

Dear all.
First of all, thanks for your attention, I really appreciate.
I have a GNote 10.1 Wi-Fi version (N8013) with stock Android 4.1.
My S-Pen was getting me crazy, because I was not able to use it correctly on the edges of the device. I tried an app that supposed to reset the alignment, but I did not work, so I googled and found that the only way to fix it was "factory reseting" the tablet.
So, I installed the TeamWin recovery and backed up my data. After that I hit the button "reboot". But before rebooting, the recovery screen "told me" that I was not rooted and "asked" if I would like to install SuperSU to get root access. I checked YES and rebooted.
After that I got stucked at the "Samsung Galaxy Note" screen (see attached file).
I've tried to switch off the note, but the screen goes off for one second and it lights up again at the same screen.
If I plug the USB cable and try to switch it off, the note goes to the battery charging screen. If I remove the USB and push the power button again, the tablet gets back to the "Samsung Galaxy Note" screen.
Odin seems to "connect" with the tablet.
I can enter both the download mode and the recovery mode (not the teamwin recovery).
Attached pictures of what I get.
Any sugestions?
Thanks!!!
Everything is ok now
Dear all,
Hope I can help you if you have a problem similar to mine.
I remembered that a PC with no OS stops on some screen, but everything else works, just as what was happening with my note.
I tought that I might have wiped more things than I should, so, the only thing I had to do was to restore the backup that I had.
To do this I should reinstall the TWRP and the only way was via Odin.
Solved the problem this way:
1. Downloaded the Odin (http://techbeasts.com/2013/08/08/download-odin-pc-latest-version-v-3-07/)
2. Downloaded the TWRP file (http://techerrata.com/get/twrp2/p4noterf/openrecovery-twrp-2.6.1.0-p4notewifi.tar)
3. Connected the Galaxy Note to my PC using the USB cable
4. Entered the "download mode"
5. Loaded the file from step 2 into the tablet using Odin
6. Rebooted the tablet
7. Entered the recovery mode (TWRP was working)
8. Restored the backup that I had
9. Rebooted again
Did the dance of victory!!!
I am so glad to have my device back.
Regards
how to access recovery mode? mine can't access recovery mode with power+volume up :crying:
rizalabd said:
how to access recovery mode? mine can't access recovery mode with power+volume up :crying:
Click to expand...
Click to collapse
Hi all
mine neither.. followed your steps with odin but still stuck in start screen (Samsung Galaxy Note 10.1). By the way mine is the 8010. I tried almost everything. Cant even load the recovery mode!.... And Have no backup either.
PLease someone help me...
Thank you in advance
I have an SM-P600
My Note 10.1 2014 Edition is stuck on the tablet title screen, not sure if its in reboot mode it returns to this screen if I try to shut it off... basically Its frozen, and when I try to shut it off it goes away a few seconds and comes back. This happened after I rooted with KingRoot, and tried to Flash a ROM, Im a complete Noob and should have done my homework... but I didnt. I see everyone suggesting odin and going into download mode... I can get to download mode but I am using a macbook pro, and there are very little options to use odin, I tried Jodin3... and Heimdall... no luck...
PLEASE HELP !
HELP stuck on Samsung screen
I didn't any root or install a different firmware to mine.
But after charging it I removed the cable and it rebooted and got stuck on the Samsung screen. I can only access to Download mode. I didn't have any Recovery mode installed, and now I can't install one successfully via Odin...
I tried to install a new firmware... a recovery mode... nothing is working...
Please I need HELP...
@ agelcer: Was your tablet rooted?
Hello. I havea similar problem with my note 2 phone. It will not get past the
samsung screen. My cpu knowledge is very limited. Are you open to accepting payment for attempting to fix my cell phone? All I want is the pictures off of it if that is all you can do to it. Pleass email me at [email protected] if you or anyone you know can help. Thanks....Jay
Same thing is happening to mine. I tried Odin but after the download the srceen goes black and then comes back to the Samsung Galaxy Note 10.1 screen.
Hello folks.
Same problem here with a n8000.
It had the stock unrooted rom probably JellyBean.
Can only access Download Mode, nothing else.
I get connection to Odin, tried to flash original firmware, 4 file firmware, re-partition with pit file, flash a custom recovery, all seem to pass through but nothing changes, still stuck on 'Samsung Galaxy Note 10.1' screen, never moves on to boot animation and still can't access Recovery Mode.
However, something else I triy with Odin and it FAILS is ticking 'Nand Erase All'. It won't let me erase nand.
Could this mean some kind of memory corruption?
Does it have anything to do with EMMC?
If it does, is there a possible way to fix without replacing the hardware?
What else can I try before giving up?
It would be nice if other users who report this problem attempt to Nand Erase All and see if it also FAILS..
Thanks alot and sorry for the long post.
Edit: after posting I found this which is PROBABLY THE SOLUTION for me.
And here is another topic on this issue.
did you find the solution?
giba_fernando said:
Hello folks.
Same problem here with a n8000.
It had the stock unrooted rom probably JellyBean.
Can only access Download Mode, nothing else.
I get connection to Odin, tried to flash original firmware, 4 file firmware, re-partition with pit file, flash a custom recovery, all seem to pass through but nothing changes, still stuck on 'Samsung Galaxy Note 10.1' screen, never moves on to boot animation and still can't access Recovery Mode.
However, something else I triy with Odin and it FAILS is ticking 'Nand Erase All'. It won't let me erase nand.
Could this mean some kind of memory corruption?
Does it have anything to do with EMMC?
If it does, is there a possible way to fix without replacing the hardware?
What else can I try before giving up?
It would be nice if other users who report this problem attempt to Nand Erase All and see if it also FAILS..
Thanks alot and sorry for the long post.
Edit: after posting I found this which is PROBABLY THE SOLUTION for me.
And here is another topic on this issue.
Click to expand...
Click to collapse
i am looking for any solution since two years without any benefit. did you find any?
chozex said:
i am looking for any solution since two years without any benefit. did you find any?
Click to expand...
Click to collapse
I assumed from my searches the solution would be JTAG or replace the EMMC.
Since I don't have the resources for any of those, I just abandoned it to the dust and rust..
bootloader
Is this after the boot loader is updated?
osirisx69 said:
Is this after the boot loader is updated?
Click to expand...
Click to collapse
I'm not very clear about bootloader upgrading, but I guess it was included in the 4 file firmware I tried flashing and it said 'success' but nothing changed..
I think it ain't just a softbrick since I can't erase nand..
What's your background, osirisx69?
This happened to ours as well just today. Unplugged it rebooted it and it's stuck. Can only access the Odin mode.
Sent from my XT1254 using Tapatalk
i got same issue at last 4 months
just try reset then got same issue.
Same problem for 3 months. Guys have anyone tried jtag flashing firmware as in this post which was provided earlier?

Categories

Resources