This is my first thread so I hope Im not double posting with my question. I am trying to get my HD2 back to stock, I have downloaded the official t-mobile rom from htc. Whenever I try to flash ROM from sd card or any radio it gets stuck at 96% or 99%. I have tried hspl 2.08 and if I do 2.08.0000 nothing will flash at all. I am at my wits end because I have tried every suggestion and have searched high and low through the threads. Any help is appreciated.
Hey! If you installed some other roms (wm, wp or android) you need program task 29!
It will clean your flash memory. After that you need to know what was the original spl on your phone (like 2.08.0000 or 3.05.0000) SPL, not HSPL! Flash your stock SPL! reboot, enter in bootloader again and connect phone in to pc, flash your stock rom while you in bootloader through pc! It works for me 100% Enjoy)
Related
I have been searching and googling for over 2 hours straight and cant find any solution to my problem:
I was going to install the Custom HD2 Android. But my radio was to old. so I decided to update it with the newest rom.
I Installed the HSPL thingy, did the whole renaming and placement of LEOIMG.nbh
and tried to install it via bootloader. But it stopped at 9% telling me: "00028002 Not allowed"
So now I cant get passed a screen:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
Upgrade ROM code error
Please try again
USB
I'm starting to believe there is nothing I can do.. Cant access my sd card when plugged to the pc or nothing..
Is there ANYTHING someone can help me with?
I believe your problem lies with SPL 3.03. I don't think even the latest HSPL will work. I think what you have to do is flash an older stock ROM in order for your SPL to revert to 2.10. Then use HSPL3 to HSPL your device. Then you can flash any ROM you want.
juggs said:
I think what you have to do is flash an older stock ROM in order for your SPL to revert to 2.10. Then use HSPL3 to HSPL your device. Then you can flash any ROM you want.
Click to expand...
Click to collapse
won't work on none tmous phone because spl 3 won't let itself downgrade to spl1. just like spl2 wouldn't downgrade to 1.
the tmous users CAN downgrade from 3 to 2, but there are no spl2 roms for none tmous users.
@OP
if you have a tmous phone then flash a stock tmous rom from sd card.
if you have a normal hd2 then you are stuck on spl3 until hspl gets updated.
EDIT - my answer was incorrect, I was being wary until someone confirmed the spl CAN be downgraded by flashing a correct stock rom for your phone (USB is fine), or by using a goldcard.
Leffernan said:
I Installed the HSPL thingy, did the whole renaming and placement of LEOIMG.nbh
and tried to install it via bootloader. But it stopped at 9% telling me: "00028002 Not allowed"
Click to expand...
Click to collapse
you flashed the 3.x rom from sd card. the first thing an sd card flash does is remove hspl, and replace it with stock spl. next, the rom checks that the phone matches the rom, which in your case it doesn't, so it stops and fails.
you could try forcing an spl 2.08.0000 tmous rom on it using goldcard, in the hope it will then allow you to run hspl2.
But all of this requires me to have access to my sd card? I don't have that :\
ah ok.then its time to wait for the next hspl version to support spl3.x
Would it be too much to ask if you could send me a pm or a mail at [email protected] whenever that happens? Probably going back to a good old Sony Ericsson in the meantime, hehe
i'd like to say yes, but it could be several weeks, and i can barely remember to feed myself from one day to the next, so..... heh.
however When it does come out, it will be hard not to notice, just skim the latest thread titles every day or two.
edit - oh, and don't give up just yet, I could be mistaken, its not unusual!. i haven't touched the 3.x rom/spl yet, so i could be wrong.
this thread, for instance,
http://forum.xda-developers.com/showthread.php?t=814838
suggests that the spl CAN be downgraded. reports are still confused.
you could for instance try flashing the 3.x rom over usb using SSPL, and then you'd at least have a working phone.
EDIT - MY RESPONSES IN THIS THREAD WERE NOT BASED ON ALL THE INFORMATION WE NOW HAVE REGARDING SPL 3.03
THE 3.03 SPL CAN BE DOWNGRADED EASILY BY USING THE CORRECT STOCK ROM FOR YOUR PHONE, FLASHED EITHER USB OR SD CARD.
My phone is running on
OS VERSION:5.2.23569
MANILA VERSION:2.5
ROM VERSION:Cruzer 5th WWE
Radio Version:2.15.50.14
I've had enough of using the Cruzer 5th rom already and wish to update back to the normal Official HTC ROM. I've downloaded the RUU_Updates for both 1.66 and 3.14 and both have failed in updating the phone's ROM.
The problem is that once my cpu has detected the phone.
The phone will then reset and get's stuck on the screen which has a few colors.(The one we use to check our HD2's flash version like HSPL). Then the loader on the screen of my CPU will be stuck at 0%. And guess what...before you know it...the entire operation will cancel and it will say that its not able to update my ROM. What on earth? Please help me. I'm only not able to update back to the official rom software. Apart from that,the other cooked roms which have been made available for download from the other users can be used to update my rom.
I need help. Please help me. Thank You! i look forward to your solutions!!!
You can use other roms and if you look/use the search option your answeres are here somewhere
could be a stuck radio rom, there have been several examples where the radio prevents spl and radio (and hence stock roms) from flashing.
try your CORRECT stock rom from sd card flash, if that fails its either
1 - not actually your correct stock rom or
2 - you are flash stuck. no clue how you would solve that.
LekHD2 said:
Then the loader on the screen of my CPU will be stuck at 0%. And guess what...before you know it...the entire operation will cancel and it will say that its not able to update my ROM.
Click to expand...
Click to collapse
I had the same problem like u 2day. All I did was instaling SPL-3.03.HSPL
At first I had two options like SPL-3.03 or SPL-3.03.HSPL to instal, that first one was making the problem that you writing of, but after I instaled SPL-3.03.HSPL I can instal other roms.
LekHD2 said:
My phone is running on
OS VERSION:5.2.23569
MANILA VERSION:2.5
ROM VERSION:Cruzer 5th WWE
Radio Version:2.15.50.14
I've had enough of using the Cruzer 5th rom already and wish to update back to the normal Official HTC ROM. I've downloaded the RUU_Updates for both 1.66 and 3.14 and both have failed in updating the phone's ROM.
The problem is that once my cpu has detected the phone.
The phone will then reset and get's stuck on the screen which has a few colors.(The one we use to check our HD2's flash version like HSPL). Then the loader on the screen of my CPU will be stuck at 0%.
Click to expand...
Click to collapse
I know you said you downloaded the two ROM's from the HTC website. I don't know if you have a TMOUS HD2 then I suggest downloading the official upstream ROM from the T-Mobile website it is the 3.14 ROM.
I think what has happen to you is you had a bad flash and if you flash the 1.66 ROM first then you changed your SPL and now you don't have the correct split to flash the flash the 3.14 ROM. I recomemd you download and use HSPL 4 to change your SPL to SPL 3.03.0000 then try to flash the update ROM. Or you could flash it via your SD card that should force the changing of your SPL with out you doin yourself. JUst my thoughts on the situation.
Hi all
Apologies if this has been covered before but I cannot find anything thus far. I upgraded my HTC HD2 (Vodafone branded) from 1.72 to 3.1.4. As the device was branded I had to use HSPL (version 3) as Vodafone had no specific version, at that time, and thus used the generic HTC version as it was all that was available at that time. This seemed fine until I hit the, what I now know to be the memory issue, with this combination. At this point after trying a number of custom ROM's, I am using a Dutty Custom ROM (V12, COM2). I decided today, as I just discovered that Vodafone now have their own specific 3.1.4 ROM update available I would flash the 3.1.4 ROM, which I was able to download legitimately from the HTC web site, using my serial number.
I first flashed the stock ROM in the vain hope that the Vodafone had fixed the memory issue. They haven't and thus I decided to remove HSPL. I did this from the installation program and chose the 0000 option which removes HSPL. I then rather stupidly decided to run a task 29, which of course, failed at 0% and just hung totally. It did not time out after 10 minutes, at which point I had no option but to remove the battery and data cable. Fortunately the phone booted up and ran normally. I thus decided to re-flash with the legitimate Vodafone 3.1.4 ROM. as the memory issue still persisted. It failed at 0% just as with the task 29. I now cannot flash ANY Rom unless I install HSPL. I have only tried version 3 thus far.
Any ideas how I can get my phone loaded up with my genuine 3.1.4 Vodafone branded ROM without HSPL and thus avoid the memory issue and load genuine ROMS and updates please? For now I am back to using the Dutty V12, COM2 ROM. Any ideas most gratefully recieved and apologies if this has been covered before.
Many thanks in advance.
Regards,
Paul Lemonidis.
Try flashing to HSPL 2 not 3, and read this thread
http://forum.xda-developers.com/showthread.php?t=609477
Russ
Flash your vodafone stock ROM over SD.
And to be able to install custom ROM, use SSPL_RUU
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Thanks
I flashed from an SD Card and all was well. I can now reflash the same version, which I could not before, without HSPL. Thus for the moment I no longer need HSPL. Thus my warranty is valid again and I have a stable phone with the latest correct vendor ROM. I may try a custom ROM again at some point in the future if I experience problems but at least I can say I gave it a fair chance.
As a sideline, Swype works beautifully with this ROM.
Once again many thanks in advance.
Regards,
Paul Lemonidis.
samsamuel said:
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Click to expand...
Click to collapse
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
netvpn7 said:
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
Click to expand...
Click to collapse
Take the 1.72 ROM and use the flash from the SD Card method. This will get you back your memory.
The reason for the memory problems is a combination of 3.14 ROM and HSPL.
I own a new HD2....and now i think i bricked it.
I installed HSPL3 on my device and then MAGLDR113 but after reboot nothing happened just white screen and green htc logo
I tried to uninstall HSPL according to manual stated in you tube but loading got lost just after a blink.
My phone is showing this info in bootloader....
PB81100 SS-BC
SPL-2.08.HSPL 8G XE
0x05
CotullsHSPL 0x50
PLeaseeeeeeee help me out.....i beg all
look at my post sounds like mine
check out post 9 in this thread sounds like mine http://forum.xda-developers.com/showthread.php?t=961001
not sure if you are tmous tho you may want to start with your shipped or test masd 2.02 rom
As far I can remember, all tutorials said that hspl can be just "uninstalled".
The only way to get rid of hspl (and maglr at once) is to flash original rom
BUT FROM SD CARD.
Tutorial how to do that is in the "sticky" (third sticky in this subforum) section.
or better still, finish the process you started. . . apply a rom.
you cant just "apply hspl, apply magldr" and then stop, you gotta enter magldr and flash a wp7/android rom.
also, if you still have the original radio that shipped with your phone, it wont be high enough version to work.
enter bootloader and flash something like radio 2.11.50.x or higher.
This is not an error or fault at all, just plain user failure.
Did you try to flash stock rom? If activesync is not allowing it, then you can try it booting your phone in boot loader mode. But make sure you flash stock rom only.
Alternately you can flash via sd as mentioned by "rtomakov"
Thanks
jeetu1981 said:
Did you try to flash stock rom? If activesync is not allowing it, then you can try it booting your phone in boot loader mode. But make sure you flash stock rom only.
Alternately you can flash via sd as mentioned by "rtomakov"
Thanks
Click to expand...
Click to collapse
Flashing stock rom via usb wont remove hspl!
so dear, you need to know this first...magldr will install in rom replacing your wm6.5......so after you do that you need a nand android build or wp7 to use with magldr or if you want wm 6.5, no need to remove hspl, just reflash the stock 1.48 wwe rom for india...search for that in the forum...this will replace the magldr..........just be sure not to flash the new stock 3.14 wwe rom over hspl..it will produce incompatibilities like small memory....if you want 3.14 rom, first flash stock 1.48 wwe, and then using hspl, uninstall hspl (select 1.42spl )...then install 3.14 wwe rom (be sure to flash india specific roms)
rtomakov said:
Flashing stock rom via usb wont remove hspl!
Click to expand...
Click to collapse
Right, but it will atleast flash a stock ROM, HSPL can be removed later
Thank u ol for helping me out.
Pblm solved I installed new 3.14 rom as it olso upgraded my radio and magldr run after boot successfully.
Now I m using windows7
parkarintl said:
Thank u ol for helping me out.
Pblm solved I installed new 3.14 rom as it olso upgraded my radio and magldr run after boot successfully.
Now I m using windows7
Click to expand...
Click to collapse
That's good to hear. WP7? I flashed it yesterday and then switched back to WM in just 15 minutes, not my cup of tea.
Thanks
I currently have a MIUI android ROM installed but want to go back to WinMo 6.5 (stock). Now when i try to flash the ROM like i did before, its says on my PC USB Init failed, connection problem. The bootloader screen does say usb. Also when I try to flash trough the MAGLDR flash modus there is USB standing but i cant flash. I've also tried flashing the stock ROM from my SD card as an NBH file but it wont work.. Also repartitioning and all the stuff dont work because they all have te connection problem. I have tried multiple USB cables. Anyone know a solution??
you say that the SD flash doesn't work, can you elaborate a bit more?
explain everything you did, what ROM did you try, if you can give me the whole step by step you tried to SD card flash, including and file name changes etc
SD flash is usually the last resort and if you tried it with a genuine original Stock ROM it should work, albeit it will change the RADIO, SPL and ROM at the same time...
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
cmour said:
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
Click to expand...
Click to collapse
just follow the guide on the relevant ROM that your interested in
but if your playing with WP then use HSPL 2.08
if your flashing a stock ROM via SD as you pointed out it will replace the SLP with the one that comes with that ROM, so it doesn't matter what you do, then you can use HSPL4 to install the required version for the ROM that you want to use. You can use HSPL 4 to revert back to a stock SPL as well, but if you have any doubt at all then just re flash a original stock ROM, you cant go wrong at all then
Well, if i try to flash anything from my pc it says connection error. When I use flasher modus the HD2 freezes and i need to pull out the battery. I also tried flashing the stock ROM from my SD card but that also doesnt work. I use MAGLDR 1.13 and HSPL 2.08 i think. The current ROM is MyMIUI V11.
i managed to install the stock rom but now i cannot install magldr. When i start the installation the hd2 shows bootloader, then goes into the installation screen but after 1 second it flashes back to bootloader.. any help?
are you putting the phone in to the tri coloured bootloader with the word "serial" at the bottom? plug in to a USB port and the word changes to "USB" then install MAGLDR?
just so im clear what you have tried