Has anyone successfully done this??
Link: http://forum.xda-developers.com/showthread.php?t=1220181
I finally hard-bricked my Vibrant, and I'm wondering if this has been accomplished, instead of sending it to a specialist to JTAG it the traditional way!!
Im trying to see if I can resurrect it myself instead of losing it for a week!
And yes I'm aware of the One guy here in the states that does JTAGing, but Id be seriously outa work for a week as my phone is my work/life line, cuz I'm an Independent contractor, so its not about the money Id spend but the time down without a way to work/communicate, I haven't contacted TMO yet and told them it was hosed using the Kies method to upgrade it to Froyo. Wish I never had done that!! Should've known better, didn't see/read any post about the horrors of using Samsungs KIES program until it was too late!!!
I was trying to purge a SH 5.0 install that went bad, I flashed back to stock Eclair. Then went to Froyo, But thats when I developed a problem with boot looping after doing Froyo, so I tried the KIES program to go to "FROYO" and that's when It bricked!!!
Anyways its bricked hard, and I'm wondering if this has actually been done successfully!
And any tips that I might need to get the Heimdall Program to actually detect it thru the USB method, would be awesome! Even though it wont turn on!!
Link to the thread: http://forum.xda-developers.com/showthread.php?t=1220181
JTAG isn't a method that can be done through usb. If you had googled jtag, you would have found out that it is a physical port built into the motherboard of our phones. In fact most electronics have a jtag port.
*Joint Test Action Group**(*JTAG*) is the common name for what was later standardized as the*IEEE
1149.1**Standard Test Access Port and Boundary-Scan Architecture*. It was initially devised for testing*printed circuit boards*using*boundary scan and is still widely used for this application.
Today JTAG is also widely used for*IC*debug ports. In the embedded processor market, essentially all modern processors support JTAG when they have enough pins.*Embedded systems*development relies on*debuggers*talking to chips with JTAG to perform operations like*single stepping*and*breakpointing. Digital electronics products such as*cell phones
*or awireless access point
*generally have no other debug or test interfaces.
In order to flash your phone, it will have to be dismantled, and hooked up to the jtag box.
Beware of angry gingerbread man
Adamcooks, I read the entire squabble about this between you and RaverXX
I downloaded your one click as well!!
So can you give me some advice on how to get my phone to even simply turn on, WO the soldering involved using traditional method of JTAGing??? Mine wont power up or show any LED activity, nothing when plugged in or do anything using traditional methods known to work with "SOFTBRICKING"
I mean, it seems my Boot loader is corrupted, or the other file you suggested, when Raver and u were arguing!! If I could even get a faint indication of life from the phone, It could be brought back to DL, but a DL Jig, as well as all the other extensive methods to get it even to power on, let alone go into DL mode isnt working at all, after many, many try's!
Can your one-click program, with the proper BL's for my T959 Vibrant be acknowledged by either yours or Heimdall's Program, so as to even be able to flash this WO, Jtaging it, even if it wont even power up in any way to handshake with my lappy???
BTW, I'm not trying to start another **** storm, after what happened with RaverXX, but it seems some of the people who had the same scenario as I do, were successful, so I'm wondering between the 2 of you, how to approach and try this, I respect both ya'll's work and contributions, but for me the bottom line is to get my phone working once again, short of either#1 JTAGing it, or trying to go thru the painful experience of trying to get TMO to replace it with a new same model, because KIES fubar'd it!!
Anyway I wish you 2 guys could lay out the proper set of instructions as you suggested, along with the proper files or links, for us to try either his method or yours. I think its possible to resurrect these phones, this way short of physical damage, and as such!! IDT you 2 fellas would've put so much effort into this theory, if there wasn't some merit to it!
So I'm all ears and eyes to your suggestion of how to get my phone to even breath again, so I can go back to DL mode, and get her working again!!
But when nothing what so ever happens, no power up, no lights, no nothing occurs, it seems to me its bricked, even though you say a truly bricked phone , has physical hardware damage, which tech is prolly correct, however in this case, mine is software bricked very hard!!!! And for purposes of communication and clarity, Ill stick with bricked, If I knew the MB was fried and or damaged, Id simply order another one, and replace it, and power up the phone, and be done with this ordeal, but my corruption occurred during using the Samsung KIES program, regrettably!!
And I'm fairly certain that either the Boot loader file is corrupted or the file you say creates a black screen usually displaying the Pc-phone logo is done for, so again, should I try the command prompt instructions to fix that, or do I use your one-click, or go to ravers method ?? I asking legitimately, because I know your knowledge in these matters has merit!! Thanks for your reply!!
Unless he changed his account, that was a different Adam in that other thread. I still say try it, cant make things any worse.
Sent from my ZenDroid, meditating on the XDA App
I may give a sharp response sometimes, but an internet squabbler I am not. connextion(sp) has a motherboard cradle that contacts the correct pins to jtag flash, without causing any damage to your phone.
Have you tried the resistance jig? I think that skorpn is the one who makes them ( 301k ohm resistor plug into the usb port can force d/l mode if the bootloaders aren't borked)
these are the last two resorts in ng phone resurrection.
Beware of angry gingerbread man
Ya My mistake Sorry
Ya I got you mixed up with another developer who has a very similar handle, so many apologies, however I wasn't flaming you anyway, shape or form, just apologizing for the mistaken ID
BTW Is the skorp resistance Jig a completely different animal from the DL Jig Tech Mobile sells doing the same result, in other words is it able to bring a phone like mine in the condition it is, into DL mode??? I saw the Skorp design, it just seems to me, its the same thing I already have from Tech Mobiles design. Accomplishing the same thing, but for phones that actually power on in some way shape or form, light off etc!!
Anyway thanks for your input, and effort, I'm still sorting all the info on everybody's suggestions and methods, short of JTaging it!!! Gonna make a move on a procedure here soon, this evening!!
Related
Hi,
I read and followed lots of excellent threads on here and successfully rooted my S2. I then flashed it with the Revolution ROM which worked fine, later tried the VK + Siyah which also ran fine.
Today I decided to try WajkIUI but after flashing and rebooting, the phone reset, the button lights came on and then it hung. Now I can't get a thing out of it, no booting, no recovery mode and no sign of it in ODIN.
It sounds completely hard-bricked but I don't really understand how it can be.
Any ideas?
Have tried soft and hard resetting but nothing.
Cheers
Without recovery mode your last best (remote) chance before you send it to Samsung would be a jig.
That's what I was thinking but why would it hard brick if the flash had worked?
And if I send if back to Samsung the warranty will be void anyway won't it?
Unfortunately that one's like asking how long a piece of string is (in other words, who knows ?). If it's a case of the NAND being stuffed as a result of the flash, a JTAG repair may fix it, but you won't know that until/unless you send it to a JTAG repairer.
It may be a hardware issue, cpu might have carked it or something.
Yeah, you've pretty much voided the warranty by putting non-stock firmware on it, but at the end of the day if Samsung can't tell it's been messed with you might get away with a warranty repair/replacement.
You'll only know that if you send it in to them to be looked at. So I guess you've got two choices to consider (not including the remote chance of the jig getting you into download mode).
I guess you could try another battery. Always the possibility it might have died.
Crap. Well, I'll give a jig a go and if that doesn't work then send it back and see what happens.
@ op
did you tried the key press combination to get into download mode? the things you have done has a very less possibility of hard brick.
That's what I thought, but no combination seems to work.
Was the battery full when you flashed?
Sent from my GT-I9100 using Tapatalk
Think it was about 96%.
You never know, it might just be a completely knackered battery. If you're planning on getting it fixed come what may, spending 20 bucks or whatever they cost in your country on another battery won't be the waste of money you might initially think.
If it doesn't fix this problem, at least you'll have a 2nd battery when you do get it fixed. I know I've found having a 2nd battery a godsend since I got mine a month ago, has come in really handy on trips where I've been away for more than a day and has meant I haven't had to worry bout bringing a charger along.
Could a battery just die like that? Seems a bit of coincidence.
Dunno. Anything's possible I guess. Yeah you're right, that would be coincidence. Given what you were doing when it died, I'm betting the NAND is shot & it will need to be JTAG'd either by Samsung or someone else.
mraquinn said:
Could a battery just die like that? Seems a bit of coincidence.
Click to expand...
Click to collapse
Which sucks. That said, according to a site in the UK it costs about £8 plus postage. Have ordered a USB jig just in case, and for £3 it's worth a go.
The really annoying thing is whether to root again if/when I do get it sorted. Am also checking with my network, see if they'll have a go under warranty and I'll forget to mention I was rooting it.
MistahBungle said:
Dunno. Anything's possible I guess. Yeah you're right, that would be coincidence. Given what you were doing when it died, I'm betting the NAND is shot & it will need to be JTAG'd either by Samsung or someone else.
Click to expand...
Click to collapse
On that note....if I wanted to upgrade to ICS, how would that be done without rooting - ie. would the counter look the same? (Long shot)
Yeah if you're going to get it fixed, chances are you'll end up flashing/rooting it again, so the jig will come in handy.
I guess that's something you'll need to decide when you get it back/get a new one. What happened to you isn't the norm tho. The large majority of flashes go smoothly for most people. But the reality is, every time you do it, you do run that small risk of it barfing for any number of a gazillion reasons (which are normally impossible to discover once it's happened). That's the risk people like us who frequent sites like this take.
Yeah if they/Samsung can't tell what happened to it, you'll possibly get away with it. And the fact you rooted it isn't information you have to volunteer to them by any means As to exactly what you should tell them, that's up to you.
Edit to add - Let us know how you get on once you have it sorted. Always useful to have people's experiences on here to give other people it happens to some kind of idea of how it might go down.
mraquinn said:
Which sucks. That said, according to a site in the UK it costs about £8 plus postage. Have ordered a USB jig just in case, and for £3 it's worth a go.
The really annoying thing is whether to root again if/when I do get it sorted. Am also checking with my network, see if they'll have a go under warranty and I'll forget to mention I was rooting it.
Click to expand...
Click to collapse
Well, according to the boffins online I have to go into a store to see if they can repair it. Hopefully they won't be able to check whether it's been rooted or not instore. In fact, if they can't power it on, I don't see how they could.
Random technical question: how can a software/firmware fault stop the hardware from even starting?
My only reference is building a PC - even if you knacker the BIOS and the harddrive, it will still power on so you can access them to put them right.
mraquinn said:
Random technical question: how can a software/firmware fault stop the hardware from even starting?
My only reference is building a PC - even if you knacker the BIOS and the harddrive, it will still power on so you can access them to put them right.
Click to expand...
Click to collapse
Firmware includes the boot sequence and recovery sequence on Android .
power goes to boot on file in effect
Or key combination goes to load recovery or download .
jje
Is that a bit of a flaw, for circumstances just like this?
And, does this mean that the USB jig has no chance of working - or is that the exact reason it might work?
JJEgan said:
Firmware includes the boot sequence and recovery sequence on Android .
power goes to boot on file in effect
Or key combination goes to load recovery or download .
jje
Click to expand...
Click to collapse
i thing jig can solve the problem
My Fascinate had an unbrickable mod done a few months ago. I tried flashing CM to it, and now it doesn't boot or go into recovery mode. Download mode is ok so far, but only with a jig. Windows and Odin can't see anything. On Linux (Ubuntu physical box not virtual) the 'unbrickable resurrector' (team hummingmod) doesn't find the device. Heimdall only prints a pit file after it first goes into dl mode, then just detects it but fails the loke handshake everytime until it goes into dl mode again. USB drivers were installed (libusb). Almost everything online says that the phone should be recoverable (like from a soft-brick) but the phone's not even getting detected. The place I mailed it to seemed to know what they're doing, but I'm wondering now if the mod was not done perfectly and if that could be causing this weird issue now. This is my main phone, and none of us are getting any younger so let's get some ideas on this asap.
Mainly, I'm wondering how to turn this from a paperweight back into a phone?
I would contact the people that did it and see what they say.
Unreliable repair site?
ndowens said:
I would contact the people that did it and see what they say.
Click to expand...
Click to collapse
I sent the repair place several messages, and they didn't respond. It's Mobile Tech Videos. When I first got the mod done a few months ago, they seemed ok. Now it's like they just don't even want to hear about the possibility of there being an issue with their work. I have friends that fix these locally, and they've also tried getting it to work using different boxes and setups so it doesn't seem like the problem is on my end (not saying it's definitely not, just doesn't seem so). I sent them messages asking whether they've had any similar issues, and if it's possible to rule out the original mod as the issue. Nothing, not a courtesy response. Nothing, like they just decided to ignore the whole issue. I actually left them some good feedback for them (originally), now I'm wondering if someone else will read that and think that this place is a reliable repair shop -- I'd feel guilty for steering them to the wrong place based on feedback that's no longer current. I could understand if they had assisted a customer in using the mod (that I paid them to do) and then that customer just didn't want to do anything, just complain, then yes I could understand that they'd not want to deal with that. But I actually just started by sending a message that there was an issue, and if they've got a workaround. Since I paid them to do this, I thought they'd at least respond. Nothing. So that could make a person wonder if they know that there's an issue with their work and just don't want to say. Personally, I'd say a business owner with integrity should either stand behind their work or issue a refund in good faith. That's the problem is that there's not enough accountability in these issues.
The phone seems pretty well bricked right now, and since A) it's one of the older original androids and B) this no one's responded here with any ideas and C) I don't know any one locally who I can trust to jtag it -- it seems more and more likely that this is a real brick.
I just got a galaxy note for my galaxy nexus last night (traded) and I took it home and install goomanager and downloaded a rom that was "compatible" it saved to the directory that goomanager puts it in so I rebooted into CWMR and cleared cache / data etc then proceeded to install zip from SD Card. it started by saying flashing kernel 4% or whatever and then came back with an error. me being as bright as I am recently...I fixed permissions and rebooted thinking that it would at least let me back into recovery.
I now have a "Dead" note sitting on the floor infinitely "charging" so to speak its just plugged into the wall, Will not boot. Is there a way I can at least get it into Download mode? Hell stick a magnet on it to erase everything even?
I don't need another paper weight..I have an iPhone for that.
Can you boot into download? If so, use Odin to flash the correct kernel.
Can you boot into recovery? If so, flash the correct kernel.
If you can't do either one, your phone is bricked and you will need to send it for a repair. $50 and one week later you will have your phone back with stock 4.0.4 ICS rom. Its called a JTAG service, from www.mobiletechvideos.com. Many note user have gone there, from just this thing.
The jig that works with other phones 99% of the time won't work with the note.
Don't trust CWR. Get your roms from our developers.
Jig 99% Of the time won't work... you made that statistic up. If button combos aren't working it's definitely worth a shot, resistors are super cheap, especially compared to jtag which doesn't sound needed here yet.
And what do you mean. "Don't trust cwr get your roms from the devs here"?
That is a recovery... he didn't download anything with it, he used goomanager.
And even if he downloaded it from here...he would've flashed it in cwm... xda isn't a custom recovery...
So you tried holding the down volume button+ power to get it into download? Flashing a kernel will not remove your recovery/download mode unless you flashed a Rom not made for your device that installed something on said partition(s).
As for the jig...don't know statistics, but I am a one percenter. Worth a shot imo.
https://www.youtube.com/watch?v=6K-lvaAop2w&feature=youtube_gdata_player
Sent from my SAMSUNG-SGH-I717 using Xparent Gray Tapatalk 2
Volume down and power, then when prompted volume up, for download mode.
And I'm also a "1% er" and my jig isn't homemade. Josh from mobile tech gave me one of his he sells on the site.
As nun said, the combos should work, they are in the bootloaders, flashing a kernel won't effect those unless says kernel is for a different device, then you wouldn't get a single thing outta the device at all, no charging screen, no bootloop. Nothing. Whatsoever.
studacris said:
Volume down and power, then when prompted volume up, for download mode.
And I'm also a "1% er" and my jig isn't homemade.
Click to expand...
Click to collapse
Right amigo 99% + 1% = 100%. You and Nunhugger are the only ones who said a jig worked for them. So actually its way higher than 99%. . . But you guys are ninjas. Your phone would probably reboot if you just told it to. I just wanted to kill the eventual jig question early.
And my response about CWR was because it sounded like he used the old app Rom Manager to see what was available. Clearly it was wrong so I told him not to trust it, and put in a plug for our developers.
When an update is released the forum gets slammed with complaints about bad flashes of incorrect kernels, and I have seen several members heal their phone by flashing the correct kernel. I just figured he was not accustomed to the button combos of the note and would get to that eventually. But if it was for the wrong device I wanted him to get his mind around the $50 and week wait.
Sheesh. . . decaf.
Well seeing that I can't Get into either mode and no button combos will work, I am assuming I need the JTAG. I figured an app like GooManager would have at least gave me the right roms for my device. it did say i717 but that could just be my memory playing tricks on me.
Man, I'm real sorry. But the JTAG service has been used by many, and with lots of positive comments. Good luck.
hahah thats okay, I mean its a great phone, definately not worth keeping in a draw collecting dust so I will go with the JTAG service. Thanks Guys!
You still have signs of life, it shows the charging animation, therefore your phone isn't bricked.
Do some searching on making a jig, I personally think it's well worth a try.
You could very well fix your phone for under $10 and have the satisfaction of accomplishing this yourself And have the know how to do it again...
It doesn't have the charging animation. just a dead black screen.
Then why did you say this?:
leveliv said:
I now have a "Dead" note sitting on the floor infinitely "charging" so to speak its just plugged into the wall, Will not boot.
Click to expand...
Click to collapse
That's more than a little misleading...
Will not boot...could mean many things.
From a easily fixed bootloop down to a brick.
Saying it was infinitely charging made it sound less severe.
if it weren't for that line, I wouldn't have bothered to tell you to use a jig.
JTAG it is
cris, why do you need to experiment with finding the proper resistance? Why should there be any variability in that circuit? Perhaps that is why some users have used up as many as six usb port replacement parts.
By the way, my 99% statistic is, like my entire post, just my opinion, and strictly a figure of speech. If it were a fact I was quoting I would have included a footnote. Remember those painful things? Do we have to include disclaimers for any figure we use? Sorry to mislead anyone!
I said "dead" because its not necessarily dead because a JTAG thing can fix it..and I said "charging" because to the normal person who didn't know anything was wrong with said device it would look like it was charging. But anyhow. I'm sending the phone out this week. I just don't understand why all the phones can't be as open as the devices straight from google.
You're phone is dead.
JTAG is akin to zombie, the phone needs disassembled and a special rig is needed to hook to the motherboard and flash EVERYTHING back to the nand at the prebootloader level.
The I717 is pretty much just as open as a nexus as far as easily modified and rooted...
No locked bootloader even which nexus have though it's a single line in a terminal to unlock, that step isn't needed on this device.
Only thing that isn't as open is the hardware drivers.
You may have flashed an incompatible kernel for a DIFFERENT device... and that on any phone will brick you.
And ranger not sure if it's the circuits within the phones that vary from device to device, ands seem to require a more specific voltage across those pins to trigger download mode
Or, if It's the resistors that are the variable. They are only rated within a certain +/- tolerance the cheaper ones having a larger margin of error.
And lol yes I am a ninja, but I didn't do anything special to my jig at all, I got mine from mobiletechvideos, funny enough it's worked on 4 captivates, a vibrant, 2 note 1s, and an s3, but didn't work on an s2 I was fixing.
the one I got from Goomanager was probably for the i700 which shouldn't even be able to happen.
They have video proof of them fixing phones with dead black screens from exactly what happened to mine using the JTAG Method. As far as I am concerned this thread can be closed cause I got the answer to my question.
the JTAG rewrites basically everything anyways so it is being sent out later this week. Till then I'll use a blackberry or something...Take care guys hopefully next time you see me post it will be to help someone and not asking for help
You'll be up and running by next weekend. By then, lots of exciting development will be happening on the released rom.
I doubt it, I live in Canada and have to send it to the states. It probably be closer to the weekend. Unless I expedite everything.
So maybe the question from the title is a little bit unclear.
The problem that i had with my phone is that one day, i got a message that a new android version appeared(4.1.2)...and obviously i clicked to download it. After the download and install when it was time to enter in my new version, a screen where a password was required appeared, saying something that my phone is encrypted, and a pass is needed to make i work...Problem is that i didn't have a previous password...
So anyway i restarted the phone...and android didn't even brought me to that screen...it just wouldn't load...So i decided to take matters in my own hands (not the best decision i made that day)...
I searched online how to do that...i found about odin..installed it ...and then tried to install android...Problem is that odin gave me errors when trying to upload the kit or something (i was in download mode with the phone)..when odin gave errors i either disconected the cable from the phone, or in some cases i got pissed off and removed the battery...
My question is...could i have broken my phone permanently by doing that ? Like i don't know...in a way..that neither an expert could fix it?
Thanks
You can scramble the NAND so badly it has to be replaced if a flash goes bad/you flash something you shouldn't be flashing (or if you do dopey things like pull a USB cable in the middle of a flash), and the way that's done is by replacing the motherboard, so you can certainly cause damage that costs money to repair, but it can pretty much always be repaired one way or another.
I seriously doubt you could bork a phone completely beyond all repair via firmware/software & without physically damaging components.
No physical damage was made to the phone...
Assuming all the alien language things that you said ...so the worst case scenario...do you have any idea how much a new motherboard would cost?
Varies widely depending on country/how much labor costs in your country. Samsung don't sell new motherboards on their own, you can either pay an authorised service centre to put a new one in (most expensive option, you normally keep your existing IMEI), or you can get a 2nd hand board from a broken/'donor' phone (How much you'll pay for one again highly variable depending on how much someone wants for their busted phone, search eBay/Google) & either swap it into your phone yourself, or if you're not confident with that sort of thing pay a local mobile repair shop to swap the boards for you (least expensive option, your IMEI will change to that of the phone the board came from).
Edit - If what I said in my PP was 'alien', I'd suggest you shouldn't have been messing with your phone in the first place & should probably avoid same when you get it fixed as well.
Teshte said:
So maybe the question from the title is a little bit unclear.
The problem that i had with my phone is that one day, i got a message that a new android version appeared(4.1.2)...and obviously i clicked to download it. After the download and install when it was time to enter in my new version, a screen where a password was required appeared, saying something that my phone is encrypted, and a pass is needed to make i work...Problem is that i didn't have a previous password...
So anyway i restarted the phone...and android didn't even brought me to that screen...it just wouldn't load...So i decided to take matters in my own hands (not the best decision i made that day)...
I searched online how to do that...i found about odin..installed it ...and then tried to install android...Problem is that odin gave me errors when trying to upload the kit or something (i was in download mode with the phone)..when odin gave errors i either disconected the cable from the phone, or in some cases i got pissed off and removed the battery...
My question is...could i have broken my phone permanently by doing that ? Like i don't know...in a way..that neither an expert could fix it?
Thanks
Click to expand...
Click to collapse
Long story short, Yes your device could be "Broken" in such a way that the only option is to replace the motherboard. You atleast tried reading and doing something, dude there are several thread regarding this matter try different strategies, try out your luck, ask questions, but don't get your hopes too high.
Sorry pal, I wish you the best of all the luck in this tiny planet of ours.
Edit : sorry I was too late, I actually started the reply almost after you posted it but I went away had a coffee then completed it.
Edit: lol to actually make a phone completely unrecoverable you might need a sledgehammer, no software related issue in the world can completely damage an electronic device(unless that software was related to triggering a nuke).
Sent from my GT-I9100 using xda app-developers app
I dun goofed. I, very ignorantly, flashed the Boeffla kernel intl. version to my poor USA phone, which could not handle that.
Now, my phone won't turn on whatsoever. Holding the power button does nothing. Recovery/Download combinations also do nothing. Battery pull did nothing. Phoan is kill. I understand that there are other ways to fix these phones but there are far too many and far too few reviews of said methods. I believe my phone is hard bricked, so I'm not sure if other types of restoration are possible. I do know of ONE, that being JTAG, but I'm not sure I want to go that far. I wanted to know if there was anything else I could do, so I came to the source of all Android knowledge, XDA-devs. forums.
I've reviewed the "Official Samsung Way" that involved shorting a resistor to force the phone into Download mode after doing some other stuff. I don't think this will work as my phone is hard bricked.
I've looked at USB JIGS. However, they appear to only fix soft bricks.
I've looked into a more unique method, but I don't own a 16 GB SD Card at the moment, only a 32 GB, so I'm not sure if that will work.
(I'm a new guy so I can't post links. Just use tinyurl . com / srslyXDA (remove the spaces and you'll get a whole link!)
I have tried it, sort of, but I'm not sure if it worked AT ALL, or if it was the fact I was using a 32 GB SD card. Either way, I'd rather not buy the SD card until I knew for sure if this would work.
Just so we're clear, I'm using a Virgin Mobile (AKA rebranded Sprint) Samsung Galaxy S3. It originally ran CM11.
Any suggestions? I'm open to JTAG but only if there's a good tutorial for it. I think someone once recommended a RIFF box but those just happen to be a good sum of money.
skarlitz said:
I dun goofed. I, very ignorantly, flashed the Boeffla kernel intl. version to my poor USA phone, which could not handle that.
Now, my phone won't turn on whatsoever. Holding the power button does nothing. Recovery/Download combinations also do nothing. Battery pull did nothing. Phoan is kill. I understand that there are other ways to fix these phones but there are far too many and far too few reviews of said methods. I believe my phone is hard bricked, so I'm not sure if other types of restoration are possible. I do know of ONE, that being JTAG, but I'm not sure I want to go that far. I wanted to know if there was anything else I could do, so I came to the source of all Android knowledge, XDA-devs. forums.
I've reviewed the "Official Samsung Way" that involved shorting a resistor to force the phone into Download mode after doing some other stuff. I don't think this will work as my phone is hard bricked.
I've looked at USB JIGS. However, they appear to only fix soft bricks.
I've looked into a more unique method, but I don't own a 16 GB SD Card at the moment, only a 32 GB, so I'm not sure if that will work.
(I'm a new guy so I can't post links. Just use tinyurl . com / srslyXDA (remove the spaces and you'll get a whole link!)
I have tried it, sort of, but I'm not sure if it worked AT ALL, or if it was the fact I was using a 32 GB SD card. Either way, I'd rather not buy the SD card until I knew for sure if this would work.
Just so we're clear, I'm using a Virgin Mobile (AKA rebranded Sprint) Samsung Galaxy S3. It originally ran CM11.
Any suggestions? I'm open to JTAG but only if there's a good tutorial for it. I think someone once recommended a RIFF box but those just happen to be a good sum of money.
Click to expand...
Click to collapse
I would atleast try the jig. i have woken up a hard bricked s2 with it.
coltlacey1 said:
I would atleast try the jig. i have woken up a hard bricked s2 with it.
Click to expand...
Click to collapse
Well I don't want to go about ordering every little thing and such. It may very well be that I need to get it repaired via JTAG, which could either be me doing it or someone else. Either way, I want to be sure. Do you know of anyone who has successfully revived an S3 with this method?
All u have to do is go to radio shack and get a few resistors, and make sure you have the right cord end. Very easy to make. Just takes a little soldering. I don't know of anyone that has done it yet on an s3 but haven't really asked around. If it doesn't work you're out maybe $5.
coltlacey1 said:
All u have to do is go to radio shack and get a few resistors, and make sure you have the right cord end. Very easy to make. Just takes a little soldering. I don't know of anyone that has done it yet on an s3 but haven't really asked around. If it doesn't work you're out maybe $5.
Click to expand...
Click to collapse
I don't think you read my post correctly. My phone is hard bricked, not soft bricked. It doesn't turn on whatsoever. It doesn't freeze, it doesn't boot loop. It stays off. No LED lights. No vibrations. Hard bricked. It'd be different if it gave signs of life, but since I flashed it with a kernel not made for my device, it is most definitely hard bricked. I'm afraid it'll need to be JTAG'd or booted off of an SD card. I don't have a 16 gb one on me at the moment so if you could let me know of anyone who does cheap JTAG.
looks like youll need to locate an sd card. I dont know of anyone that does cheap jtags but i did see a youtube link somewhere that was addressing jtag inquiries but it was from some time ago.
if you do locate an sd >>http://forum.xda-developers.com/galaxy-s3/general/galaxy-s-iii-gt-i9300-hard-brick-fix-t1916796