I dun goofed. I, very ignorantly, flashed the Boeffla kernel intl. version to my poor USA phone, which could not handle that.
Now, my phone won't turn on whatsoever. Holding the power button does nothing. Recovery/Download combinations also do nothing. Battery pull did nothing. Phoan is kill. I understand that there are other ways to fix these phones but there are far too many and far too few reviews of said methods. I believe my phone is hard bricked, so I'm not sure if other types of restoration are possible. I do know of ONE, that being JTAG, but I'm not sure I want to go that far. I wanted to know if there was anything else I could do, so I came to the source of all Android knowledge, XDA-devs. forums.
I've reviewed the "Official Samsung Way" that involved shorting a resistor to force the phone into Download mode after doing some other stuff. I don't think this will work as my phone is hard bricked.
I've looked at USB JIGS. However, they appear to only fix soft bricks.
I've looked into a more unique method, but I don't own a 16 GB SD Card at the moment, only a 32 GB, so I'm not sure if that will work.
(I'm a new guy so I can't post links. Just use tinyurl . com / srslyXDA (remove the spaces and you'll get a whole link!)
I have tried it, sort of, but I'm not sure if it worked AT ALL, or if it was the fact I was using a 32 GB SD card. Either way, I'd rather not buy the SD card until I knew for sure if this would work.
Just so we're clear, I'm using a Virgin Mobile (AKA rebranded Sprint) Samsung Galaxy S3. It originally ran CM11.
Any suggestions? I'm open to JTAG but only if there's a good tutorial for it. I think someone once recommended a RIFF box but those just happen to be a good sum of money.
skarlitz said:
I dun goofed. I, very ignorantly, flashed the Boeffla kernel intl. version to my poor USA phone, which could not handle that.
Now, my phone won't turn on whatsoever. Holding the power button does nothing. Recovery/Download combinations also do nothing. Battery pull did nothing. Phoan is kill. I understand that there are other ways to fix these phones but there are far too many and far too few reviews of said methods. I believe my phone is hard bricked, so I'm not sure if other types of restoration are possible. I do know of ONE, that being JTAG, but I'm not sure I want to go that far. I wanted to know if there was anything else I could do, so I came to the source of all Android knowledge, XDA-devs. forums.
I've reviewed the "Official Samsung Way" that involved shorting a resistor to force the phone into Download mode after doing some other stuff. I don't think this will work as my phone is hard bricked.
I've looked at USB JIGS. However, they appear to only fix soft bricks.
I've looked into a more unique method, but I don't own a 16 GB SD Card at the moment, only a 32 GB, so I'm not sure if that will work.
(I'm a new guy so I can't post links. Just use tinyurl . com / srslyXDA (remove the spaces and you'll get a whole link!)
I have tried it, sort of, but I'm not sure if it worked AT ALL, or if it was the fact I was using a 32 GB SD card. Either way, I'd rather not buy the SD card until I knew for sure if this would work.
Just so we're clear, I'm using a Virgin Mobile (AKA rebranded Sprint) Samsung Galaxy S3. It originally ran CM11.
Any suggestions? I'm open to JTAG but only if there's a good tutorial for it. I think someone once recommended a RIFF box but those just happen to be a good sum of money.
Click to expand...
Click to collapse
I would atleast try the jig. i have woken up a hard bricked s2 with it.
coltlacey1 said:
I would atleast try the jig. i have woken up a hard bricked s2 with it.
Click to expand...
Click to collapse
Well I don't want to go about ordering every little thing and such. It may very well be that I need to get it repaired via JTAG, which could either be me doing it or someone else. Either way, I want to be sure. Do you know of anyone who has successfully revived an S3 with this method?
All u have to do is go to radio shack and get a few resistors, and make sure you have the right cord end. Very easy to make. Just takes a little soldering. I don't know of anyone that has done it yet on an s3 but haven't really asked around. If it doesn't work you're out maybe $5.
coltlacey1 said:
All u have to do is go to radio shack and get a few resistors, and make sure you have the right cord end. Very easy to make. Just takes a little soldering. I don't know of anyone that has done it yet on an s3 but haven't really asked around. If it doesn't work you're out maybe $5.
Click to expand...
Click to collapse
I don't think you read my post correctly. My phone is hard bricked, not soft bricked. It doesn't turn on whatsoever. It doesn't freeze, it doesn't boot loop. It stays off. No LED lights. No vibrations. Hard bricked. It'd be different if it gave signs of life, but since I flashed it with a kernel not made for my device, it is most definitely hard bricked. I'm afraid it'll need to be JTAG'd or booted off of an SD card. I don't have a 16 gb one on me at the moment so if you could let me know of anyone who does cheap JTAG.
looks like youll need to locate an sd card. I dont know of anyone that does cheap jtags but i did see a youtube link somewhere that was addressing jtag inquiries but it was from some time ago.
if you do locate an sd >>http://forum.xda-developers.com/galaxy-s3/general/galaxy-s-iii-gt-i9300-hard-brick-fix-t1916796
Related
Has anyone successfully done this??
Link: http://forum.xda-developers.com/showthread.php?t=1220181
I finally hard-bricked my Vibrant, and I'm wondering if this has been accomplished, instead of sending it to a specialist to JTAG it the traditional way!!
Im trying to see if I can resurrect it myself instead of losing it for a week!
And yes I'm aware of the One guy here in the states that does JTAGing, but Id be seriously outa work for a week as my phone is my work/life line, cuz I'm an Independent contractor, so its not about the money Id spend but the time down without a way to work/communicate, I haven't contacted TMO yet and told them it was hosed using the Kies method to upgrade it to Froyo. Wish I never had done that!! Should've known better, didn't see/read any post about the horrors of using Samsungs KIES program until it was too late!!!
I was trying to purge a SH 5.0 install that went bad, I flashed back to stock Eclair. Then went to Froyo, But thats when I developed a problem with boot looping after doing Froyo, so I tried the KIES program to go to "FROYO" and that's when It bricked!!!
Anyways its bricked hard, and I'm wondering if this has actually been done successfully!
And any tips that I might need to get the Heimdall Program to actually detect it thru the USB method, would be awesome! Even though it wont turn on!!
Link to the thread: http://forum.xda-developers.com/showthread.php?t=1220181
JTAG isn't a method that can be done through usb. If you had googled jtag, you would have found out that it is a physical port built into the motherboard of our phones. In fact most electronics have a jtag port.
*Joint Test Action Group**(*JTAG*) is the common name for what was later standardized as the*IEEE
1149.1**Standard Test Access Port and Boundary-Scan Architecture*. It was initially devised for testing*printed circuit boards*using*boundary scan and is still widely used for this application.
Today JTAG is also widely used for*IC*debug ports. In the embedded processor market, essentially all modern processors support JTAG when they have enough pins.*Embedded systems*development relies on*debuggers*talking to chips with JTAG to perform operations like*single stepping*and*breakpointing. Digital electronics products such as*cell phones
*or awireless access point
*generally have no other debug or test interfaces.
In order to flash your phone, it will have to be dismantled, and hooked up to the jtag box.
Beware of angry gingerbread man
Adamcooks, I read the entire squabble about this between you and RaverXX
I downloaded your one click as well!!
So can you give me some advice on how to get my phone to even simply turn on, WO the soldering involved using traditional method of JTAGing??? Mine wont power up or show any LED activity, nothing when plugged in or do anything using traditional methods known to work with "SOFTBRICKING"
I mean, it seems my Boot loader is corrupted, or the other file you suggested, when Raver and u were arguing!! If I could even get a faint indication of life from the phone, It could be brought back to DL, but a DL Jig, as well as all the other extensive methods to get it even to power on, let alone go into DL mode isnt working at all, after many, many try's!
Can your one-click program, with the proper BL's for my T959 Vibrant be acknowledged by either yours or Heimdall's Program, so as to even be able to flash this WO, Jtaging it, even if it wont even power up in any way to handshake with my lappy???
BTW, I'm not trying to start another **** storm, after what happened with RaverXX, but it seems some of the people who had the same scenario as I do, were successful, so I'm wondering between the 2 of you, how to approach and try this, I respect both ya'll's work and contributions, but for me the bottom line is to get my phone working once again, short of either#1 JTAGing it, or trying to go thru the painful experience of trying to get TMO to replace it with a new same model, because KIES fubar'd it!!
Anyway I wish you 2 guys could lay out the proper set of instructions as you suggested, along with the proper files or links, for us to try either his method or yours. I think its possible to resurrect these phones, this way short of physical damage, and as such!! IDT you 2 fellas would've put so much effort into this theory, if there wasn't some merit to it!
So I'm all ears and eyes to your suggestion of how to get my phone to even breath again, so I can go back to DL mode, and get her working again!!
But when nothing what so ever happens, no power up, no lights, no nothing occurs, it seems to me its bricked, even though you say a truly bricked phone , has physical hardware damage, which tech is prolly correct, however in this case, mine is software bricked very hard!!!! And for purposes of communication and clarity, Ill stick with bricked, If I knew the MB was fried and or damaged, Id simply order another one, and replace it, and power up the phone, and be done with this ordeal, but my corruption occurred during using the Samsung KIES program, regrettably!!
And I'm fairly certain that either the Boot loader file is corrupted or the file you say creates a black screen usually displaying the Pc-phone logo is done for, so again, should I try the command prompt instructions to fix that, or do I use your one-click, or go to ravers method ?? I asking legitimately, because I know your knowledge in these matters has merit!! Thanks for your reply!!
Unless he changed his account, that was a different Adam in that other thread. I still say try it, cant make things any worse.
Sent from my ZenDroid, meditating on the XDA App
I may give a sharp response sometimes, but an internet squabbler I am not. connextion(sp) has a motherboard cradle that contacts the correct pins to jtag flash, without causing any damage to your phone.
Have you tried the resistance jig? I think that skorpn is the one who makes them ( 301k ohm resistor plug into the usb port can force d/l mode if the bootloaders aren't borked)
these are the last two resorts in ng phone resurrection.
Beware of angry gingerbread man
Ya My mistake Sorry
Ya I got you mixed up with another developer who has a very similar handle, so many apologies, however I wasn't flaming you anyway, shape or form, just apologizing for the mistaken ID
BTW Is the skorp resistance Jig a completely different animal from the DL Jig Tech Mobile sells doing the same result, in other words is it able to bring a phone like mine in the condition it is, into DL mode??? I saw the Skorp design, it just seems to me, its the same thing I already have from Tech Mobiles design. Accomplishing the same thing, but for phones that actually power on in some way shape or form, light off etc!!
Anyway thanks for your input, and effort, I'm still sorting all the info on everybody's suggestions and methods, short of JTaging it!!! Gonna make a move on a procedure here soon, this evening!!
Hi,
I read and followed lots of excellent threads on here and successfully rooted my S2. I then flashed it with the Revolution ROM which worked fine, later tried the VK + Siyah which also ran fine.
Today I decided to try WajkIUI but after flashing and rebooting, the phone reset, the button lights came on and then it hung. Now I can't get a thing out of it, no booting, no recovery mode and no sign of it in ODIN.
It sounds completely hard-bricked but I don't really understand how it can be.
Any ideas?
Have tried soft and hard resetting but nothing.
Cheers
Without recovery mode your last best (remote) chance before you send it to Samsung would be a jig.
That's what I was thinking but why would it hard brick if the flash had worked?
And if I send if back to Samsung the warranty will be void anyway won't it?
Unfortunately that one's like asking how long a piece of string is (in other words, who knows ?). If it's a case of the NAND being stuffed as a result of the flash, a JTAG repair may fix it, but you won't know that until/unless you send it to a JTAG repairer.
It may be a hardware issue, cpu might have carked it or something.
Yeah, you've pretty much voided the warranty by putting non-stock firmware on it, but at the end of the day if Samsung can't tell it's been messed with you might get away with a warranty repair/replacement.
You'll only know that if you send it in to them to be looked at. So I guess you've got two choices to consider (not including the remote chance of the jig getting you into download mode).
I guess you could try another battery. Always the possibility it might have died.
Crap. Well, I'll give a jig a go and if that doesn't work then send it back and see what happens.
@ op
did you tried the key press combination to get into download mode? the things you have done has a very less possibility of hard brick.
That's what I thought, but no combination seems to work.
Was the battery full when you flashed?
Sent from my GT-I9100 using Tapatalk
Think it was about 96%.
You never know, it might just be a completely knackered battery. If you're planning on getting it fixed come what may, spending 20 bucks or whatever they cost in your country on another battery won't be the waste of money you might initially think.
If it doesn't fix this problem, at least you'll have a 2nd battery when you do get it fixed. I know I've found having a 2nd battery a godsend since I got mine a month ago, has come in really handy on trips where I've been away for more than a day and has meant I haven't had to worry bout bringing a charger along.
Could a battery just die like that? Seems a bit of coincidence.
Dunno. Anything's possible I guess. Yeah you're right, that would be coincidence. Given what you were doing when it died, I'm betting the NAND is shot & it will need to be JTAG'd either by Samsung or someone else.
mraquinn said:
Could a battery just die like that? Seems a bit of coincidence.
Click to expand...
Click to collapse
Which sucks. That said, according to a site in the UK it costs about £8 plus postage. Have ordered a USB jig just in case, and for £3 it's worth a go.
The really annoying thing is whether to root again if/when I do get it sorted. Am also checking with my network, see if they'll have a go under warranty and I'll forget to mention I was rooting it.
MistahBungle said:
Dunno. Anything's possible I guess. Yeah you're right, that would be coincidence. Given what you were doing when it died, I'm betting the NAND is shot & it will need to be JTAG'd either by Samsung or someone else.
Click to expand...
Click to collapse
On that note....if I wanted to upgrade to ICS, how would that be done without rooting - ie. would the counter look the same? (Long shot)
Yeah if you're going to get it fixed, chances are you'll end up flashing/rooting it again, so the jig will come in handy.
I guess that's something you'll need to decide when you get it back/get a new one. What happened to you isn't the norm tho. The large majority of flashes go smoothly for most people. But the reality is, every time you do it, you do run that small risk of it barfing for any number of a gazillion reasons (which are normally impossible to discover once it's happened). That's the risk people like us who frequent sites like this take.
Yeah if they/Samsung can't tell what happened to it, you'll possibly get away with it. And the fact you rooted it isn't information you have to volunteer to them by any means As to exactly what you should tell them, that's up to you.
Edit to add - Let us know how you get on once you have it sorted. Always useful to have people's experiences on here to give other people it happens to some kind of idea of how it might go down.
mraquinn said:
Which sucks. That said, according to a site in the UK it costs about £8 plus postage. Have ordered a USB jig just in case, and for £3 it's worth a go.
The really annoying thing is whether to root again if/when I do get it sorted. Am also checking with my network, see if they'll have a go under warranty and I'll forget to mention I was rooting it.
Click to expand...
Click to collapse
Well, according to the boffins online I have to go into a store to see if they can repair it. Hopefully they won't be able to check whether it's been rooted or not instore. In fact, if they can't power it on, I don't see how they could.
Random technical question: how can a software/firmware fault stop the hardware from even starting?
My only reference is building a PC - even if you knacker the BIOS and the harddrive, it will still power on so you can access them to put them right.
mraquinn said:
Random technical question: how can a software/firmware fault stop the hardware from even starting?
My only reference is building a PC - even if you knacker the BIOS and the harddrive, it will still power on so you can access them to put them right.
Click to expand...
Click to collapse
Firmware includes the boot sequence and recovery sequence on Android .
power goes to boot on file in effect
Or key combination goes to load recovery or download .
jje
Is that a bit of a flaw, for circumstances just like this?
And, does this mean that the USB jig has no chance of working - or is that the exact reason it might work?
JJEgan said:
Firmware includes the boot sequence and recovery sequence on Android .
power goes to boot on file in effect
Or key combination goes to load recovery or download .
jje
Click to expand...
Click to collapse
i thing jig can solve the problem
Hi There,
I did search around and didn't find a specific answer to this, I did see someone was looking to modify some binary values but no confirmation if it worked. Anyways I have successfully used many roms on my phone and tablet but last night after using CWM and the rom flashed successfully I rebooted the device and then nothing. Blank screen. Nothing happens when I charge. Used the wife's battery fully charged to see if it would help. Tried three-button boot method. All nothing. It's just dead.
Now I'm guessing I must have missed a step somewhere and fully take responsibility for what happened, and would pay for a repair - but can Samsung even repair a device in this state? I talked to an agent on the phone last night and openly told them what happened and asked how much it would be to repair and he said he couldn't give me any information without sending the device in. This is my mistake to get my phone in this state so I don't want to sneak my way into a warranty replacement. Is it worth the wait as Samsung can fix this, or should I just buy a new phone?
Cheers and any information is much appreciated.
www.mobiletechvideos.com
They can repair bricked phones for a very reasonable cost. Samsung may see it and void your warranty. I'd go with Mobiletech. I've heard they do great work on bricked phones.
The above advice is good, assuming your device is truely hard bricked.
However, from your description, it's hard to figure how you bricked it. A true brick usually happens when an attempt to flash a bootloader partition gets interrupted in the middle. There are possibly other ways, but it's not very easy, actually. So, is there absolutely no sign of life? Nothing you can do will even get a flicker of light on the screen? You cannot enter download mode, or recovery mode. You have tried all of these? No point in spending $50 on a jtag repair if you can recover the phone yourself.
I would also be interested in a complete description of the steps that led up to the problem.
I'm a little embarrassed to post this but don't want to waste anyone's time. It is totally bricked but I know why.
I just noticed I downloaded a rom from the i777 forum, and my device is a i727.
Oooops! Guess I'm learning a valuable $50 (plus shipping) lesson.
Thanks for the help, my phone is off Mobile Tech.
Still might not be hard bricked. Mine did this a few weeks ago for no reason. Had been running fine then wouldn't boot one day. Wouldn't boot at all. Could not get into recovery.Nothing. Only thing that worked was connecting through Odin. Had to then flash original Gingerbread. Phone then booted fine. I have since rooted again and I'm now dual-booting SHOstock and Rootbox. Try Odin first.
SPatMobile said:
I'm a little embarrassed to post this but don't want to waste anyone's time. It is totally bricked but I know why.
I just noticed I downloaded a rom from the i777 forum, and my device is a i727.
Oooops! Guess I'm learning a valuable $50 (plus shipping) lesson.
Thanks for the help, my phone is off Mobile Tech.
Click to expand...
Click to collapse
I don't really know much about the I727 architecture, but I seriously doubt if your device is hard bricked. You should still be able to get into download mode via the normal procedure (maybe, or if not with a usb jig) for your phone, and then flash a good I727 rom, I believe. There are no bootloaders or partition information, or param files in any of the I777 roms, as far as I know, so there's really not much of anything that can do serious damage.
Try getting in to download mode by With your phone off and unplugged. Enter download mode by pressing and holding the power and volume down buttons and plugging in the USB cable before the lights blink. I don't know it will work on i727 but worth a try..GL
This is a good thread to help you read all you can....
http://forum.xda-developers.com/showthread.php?t=1652398
creepyncrawly said:
I don't really know much about the I727 architecture, but I seriously doubt if your device is hard bricked. You should still be able to get into download mode via the normal procedure (maybe, or if not with a usb jig) for your phone, and then flash a good I727 rom, I believe. There are no bootloaders or partition information, or param files in any of the I777 roms, as far as I know, so there's really not much of anything that can do serious damage.
Click to expand...
Click to collapse
Interesting. Well I suppose it is possible I had a legitamite hardware failure completely unrelated to the software issues. I did some searching around for hardware failures instead and found some very similar cases to this.
Exactly what happened. I downloaded the wrong rom, rebooted in cwm, wiped, then flashed the rom. It went successfully and I rebooted from cwm then during boot right after the samsung logo all the lights went off and the screen went black. I left it like this for about 45 mins to an hour and had dinner just in case it was still doing something. The battery was fully charged at the time I started the procedure, and I have tried using the wife's battery to make sure mine wasn't dead. My battery also functions without issues in her phone. I had done this successfully multiple times on my phone before and tablet, and successfully flashed two or three different roms on my wifes phone last night.
I tried every suggestion mentioned, and followed the guide as well. There is no glimar of life. If this is hardware I might be wasting my money with Mobile Tech but I suppose we'll know for sure soon. Phone is shipping off today.
Have you tried a jig?
Sent from my SGH-I777 using xda app-developers app
you're doing the right choice, mobile tech is your best bet
OP got his answer. And his device is an i727. Let's let this one die before we attract trolls
Sent from my SGH-I777 using Tapatalk 2
Ya good idea
Sent from my SAMSUNG-SGH-I777 using XDA
In case anyone was interested it looks like the device was a hardware failure.
"Unfortunately, I was not able to repair your device. The device's onboard EMMC controller was in a non-responsive state. It is advised to try out warranty replacement if possible or to search for a parts device and use it's mainboard for the swap."
*edit - I tried to use the thanks meter for everyone, but thanks for all the help!
Never was really a samsung fan until I got my i777. Blackjack? wth was that? Browsing with opera was off the hook though so the phone grew on me. Now I tried simply flashing a different i777 kernal because ICS constantly freezes and the phone bricks? Sent it to Mobile Tech Videos.... EMMC is in non responsive state for me too wtf Samsung? Had my nexus one twice as long and flashed twice as many times and its still rockin. Now will definitely think twice before going Sammy.
paulfrankie said:
Never was really a samsung fan until I got my i777. Blackjack? wth was that? Browsing with opera was off the hook though so the phone grew on me. Now I tried simply flashing a different i777 kernal because ICS constantly freezes and the phone bricks? Sent it to Mobile Tech Videos.... EMMC is in non responsive state for me too wtf Samsung? Had my nexus one twice as long and flashed twice as many times and its still rockin. Now will definitely think twice before going Sammy.
Click to expand...
Click to collapse
Did you wipe in ICS's stock recovery before flashing that different kernel? Because there's a well known brickbug with the I777's stock ICS kernel, where if you use it to do anything before you flash custom kernels, it'll mess up your EMMC and brick your phone. If this is what happened to you, I would suggest you do more reading before flashing anything again; different phones operate differently, and even if you're a pro at flashing stuff on a galaxy nexus that doesn't mean squat when it comes to flashing an I777. I don't mean to be harsh or offend you, I just want you to know that reading more is always a good idea, and that there's a chance that it wasn't Samsung's fault you wound up with a bricked device.
He could always try the jig to kick it into download mode. Read up about it. It may save you some money.
HTC = Hate The Consumer
Mobile tech will fix ya but in all seriousness, phones are way different from model to model. As previously stated. Read a lot before doing anything. may Atrix is way different than this phone,.
Sent from my SGH-I777 using Tapatalk 2
I just got a galaxy note for my galaxy nexus last night (traded) and I took it home and install goomanager and downloaded a rom that was "compatible" it saved to the directory that goomanager puts it in so I rebooted into CWMR and cleared cache / data etc then proceeded to install zip from SD Card. it started by saying flashing kernel 4% or whatever and then came back with an error. me being as bright as I am recently...I fixed permissions and rebooted thinking that it would at least let me back into recovery.
I now have a "Dead" note sitting on the floor infinitely "charging" so to speak its just plugged into the wall, Will not boot. Is there a way I can at least get it into Download mode? Hell stick a magnet on it to erase everything even?
I don't need another paper weight..I have an iPhone for that.
Can you boot into download? If so, use Odin to flash the correct kernel.
Can you boot into recovery? If so, flash the correct kernel.
If you can't do either one, your phone is bricked and you will need to send it for a repair. $50 and one week later you will have your phone back with stock 4.0.4 ICS rom. Its called a JTAG service, from www.mobiletechvideos.com. Many note user have gone there, from just this thing.
The jig that works with other phones 99% of the time won't work with the note.
Don't trust CWR. Get your roms from our developers.
Jig 99% Of the time won't work... you made that statistic up. If button combos aren't working it's definitely worth a shot, resistors are super cheap, especially compared to jtag which doesn't sound needed here yet.
And what do you mean. "Don't trust cwr get your roms from the devs here"?
That is a recovery... he didn't download anything with it, he used goomanager.
And even if he downloaded it from here...he would've flashed it in cwm... xda isn't a custom recovery...
So you tried holding the down volume button+ power to get it into download? Flashing a kernel will not remove your recovery/download mode unless you flashed a Rom not made for your device that installed something on said partition(s).
As for the jig...don't know statistics, but I am a one percenter. Worth a shot imo.
https://www.youtube.com/watch?v=6K-lvaAop2w&feature=youtube_gdata_player
Sent from my SAMSUNG-SGH-I717 using Xparent Gray Tapatalk 2
Volume down and power, then when prompted volume up, for download mode.
And I'm also a "1% er" and my jig isn't homemade. Josh from mobile tech gave me one of his he sells on the site.
As nun said, the combos should work, they are in the bootloaders, flashing a kernel won't effect those unless says kernel is for a different device, then you wouldn't get a single thing outta the device at all, no charging screen, no bootloop. Nothing. Whatsoever.
studacris said:
Volume down and power, then when prompted volume up, for download mode.
And I'm also a "1% er" and my jig isn't homemade.
Click to expand...
Click to collapse
Right amigo 99% + 1% = 100%. You and Nunhugger are the only ones who said a jig worked for them. So actually its way higher than 99%. . . But you guys are ninjas. Your phone would probably reboot if you just told it to. I just wanted to kill the eventual jig question early.
And my response about CWR was because it sounded like he used the old app Rom Manager to see what was available. Clearly it was wrong so I told him not to trust it, and put in a plug for our developers.
When an update is released the forum gets slammed with complaints about bad flashes of incorrect kernels, and I have seen several members heal their phone by flashing the correct kernel. I just figured he was not accustomed to the button combos of the note and would get to that eventually. But if it was for the wrong device I wanted him to get his mind around the $50 and week wait.
Sheesh. . . decaf.
Well seeing that I can't Get into either mode and no button combos will work, I am assuming I need the JTAG. I figured an app like GooManager would have at least gave me the right roms for my device. it did say i717 but that could just be my memory playing tricks on me.
Man, I'm real sorry. But the JTAG service has been used by many, and with lots of positive comments. Good luck.
hahah thats okay, I mean its a great phone, definately not worth keeping in a draw collecting dust so I will go with the JTAG service. Thanks Guys!
You still have signs of life, it shows the charging animation, therefore your phone isn't bricked.
Do some searching on making a jig, I personally think it's well worth a try.
You could very well fix your phone for under $10 and have the satisfaction of accomplishing this yourself And have the know how to do it again...
It doesn't have the charging animation. just a dead black screen.
Then why did you say this?:
leveliv said:
I now have a "Dead" note sitting on the floor infinitely "charging" so to speak its just plugged into the wall, Will not boot.
Click to expand...
Click to collapse
That's more than a little misleading...
Will not boot...could mean many things.
From a easily fixed bootloop down to a brick.
Saying it was infinitely charging made it sound less severe.
if it weren't for that line, I wouldn't have bothered to tell you to use a jig.
JTAG it is
cris, why do you need to experiment with finding the proper resistance? Why should there be any variability in that circuit? Perhaps that is why some users have used up as many as six usb port replacement parts.
By the way, my 99% statistic is, like my entire post, just my opinion, and strictly a figure of speech. If it were a fact I was quoting I would have included a footnote. Remember those painful things? Do we have to include disclaimers for any figure we use? Sorry to mislead anyone!
I said "dead" because its not necessarily dead because a JTAG thing can fix it..and I said "charging" because to the normal person who didn't know anything was wrong with said device it would look like it was charging. But anyhow. I'm sending the phone out this week. I just don't understand why all the phones can't be as open as the devices straight from google.
You're phone is dead.
JTAG is akin to zombie, the phone needs disassembled and a special rig is needed to hook to the motherboard and flash EVERYTHING back to the nand at the prebootloader level.
The I717 is pretty much just as open as a nexus as far as easily modified and rooted...
No locked bootloader even which nexus have though it's a single line in a terminal to unlock, that step isn't needed on this device.
Only thing that isn't as open is the hardware drivers.
You may have flashed an incompatible kernel for a DIFFERENT device... and that on any phone will brick you.
And ranger not sure if it's the circuits within the phones that vary from device to device, ands seem to require a more specific voltage across those pins to trigger download mode
Or, if It's the resistors that are the variable. They are only rated within a certain +/- tolerance the cheaper ones having a larger margin of error.
And lol yes I am a ninja, but I didn't do anything special to my jig at all, I got mine from mobiletechvideos, funny enough it's worked on 4 captivates, a vibrant, 2 note 1s, and an s3, but didn't work on an s2 I was fixing.
the one I got from Goomanager was probably for the i700 which shouldn't even be able to happen.
They have video proof of them fixing phones with dead black screens from exactly what happened to mine using the JTAG Method. As far as I am concerned this thread can be closed cause I got the answer to my question.
the JTAG rewrites basically everything anyways so it is being sent out later this week. Till then I'll use a blackberry or something...Take care guys hopefully next time you see me post it will be to help someone and not asking for help
You'll be up and running by next weekend. By then, lots of exciting development will be happening on the released rom.
I doubt it, I live in Canada and have to send it to the states. It probably be closer to the weekend. Unless I expedite everything.
Hello,
I have a Verizon Samsung Galaxy S4 SCH-i545. This phone was given to me by my buddy from work to try and fix it for him. I asked him whats wrong with the phone he said he doesn't know he said he went to bed and left it charged and the screen would never come on any more.
I've tried working know good battery
Working wall charger & USB cable
Tried pressing Home button and power button together and holding it
Tried pressing different combinations of home/power vol up/down
Installed KIES thinking the drivers would load
Still cant get this to come on.
I tried doing the same things while having the phone plugged in with the USB to a computer but the only message i got was unable to load drivers for qhusb_dload
I finally found drivers from the forums and installed them, i looked up a few other threads that didn't specify the how-to for the S4 but i downloaded Odin and a stock ROM firmware for the Verizon S4 but still even with the drivers installed Odin was still not able to recognize it. I am unable to find a Guide specifically for this model S4 and after a lot of searching it sounds like i need either some kind of JTAG RIFF or some kind of MicroSD card 16GB or 32GB with some software on it. If i need to solider anything to the board I have no problem in doing so. If i can avoid soldering and do the SD card fix that would be even better or anything else that i need to do in order to get this phone to work again..
Can someone help me out with this S4 qhusb_dload issue or point me to the correct thread so I can get this phone up and going again. The Data is not important to him as he said there's noting important he doesn't already have.
Odin/Download mode is accomplished by holding down Vol- and power and then let go of only power when screen lights up (even if still black) ... that doesn't work?
The the phone work AT QLL? It doesn't seem like it does. If so, you have a chance of getting the debrick image on a micro SD...
...reading over this again, yeah you're hard bricked, going to need JTAG
ToastyZ71 said:
...reading over this again, yeah you're hard bricked, going to need JTAG
Click to expand...
Click to collapse
Hi, yah after reading many other threads i feel like its called a hard brick and not a soft brick as you said.
I was reading about jtag but the device needed is called Jtag Riff and cost over $100, is that the only hardware device i can use in order to fix this phone? If there is another way can someone point me to a thread so i can try to save this phone?
Thank you for your help
mikey323 said:
Hi, yah after reading many other threads i feel like its called a hard brick and not a soft brick as you said.
I was reading about jtag but the device needed is called Jtag Riff and cost over $100, is that the only hardware device i can use in order to fix this phone? If there is another way can someone point me to a thread so i can try to save this phone?
Thank you for your help
Click to expand...
Click to collapse
As far as I know, that's it. Every other method, including USB Jig are for softbrick. - at over $100 for the JTAG Riff, might be better off hitting up swappa for a used/replacement device.
25 bucks on eBay to get it jtag. http://m.ebay.com/itm/181786279537?_mwBanner=1