[Q] Screen won't wakeup after the sleep - Streak 5 Q&A, Help & Troubleshooting

Hi everyone, i've been using DJ_Steve 1.9.1 before and after i changed my internal memory card to a Class 10. Everything works great before i changed the memory, no random reboots, no hangs. But now after i replaced the memory, it's just sometimes (not all the time), my streak won't wake after the screen timeout. So when i press the power button to wake my streak, the screen would just still dead. No response. Press it multiple times still no response. Long-pressing the power button also doesn't restart the device (usually it is). And the solution i have so far is pull the battery and turn it on again.
I have tried to flash my rom and recovery back to stock 360 and no same problem, everything just fine, so i think this is not a hardware failure, thats why i'm sure i won't have the sleep problem again after i flash back again to 1.9.1. But after a factory reset and a bit of restoring apps, i left my streak and there we go again. It won't wake anymore..
If maybe anybody here have a solution or some mind on it, you're greatly appreciated!
Sent from my Dell Streak

coyle_Gyver said:
Hi everyone, i've been using DJ_Steve 1.9.1 before and after i changed my internal memory card to a Class 10. Everything works great before i changed the memory, no random reboots, no hangs. But now after i replaced the memory, it's just sometimes (not all the time), my streak won't wake after the screen timeout. So when i press the power button to wake my streak, the screen would just still dead. No response. Press it multiple times still no response. Long-pressing the power button also doesn't restart the device (usually it is). And the solution i have so far is pull the battery and turn it on again.
I have tried to flash my rom and recovery back to stock 360 and no same problem, everything just fine, so i think this is not a hardware failure, thats why i'm sure i won't have the sleep problem again after i flash back again to 1.9.1. But after a factory reset and a bit of restoring apps, i left my streak and there we go again. It won't wake anymore..
If maybe anybody here have a solution or some mind on it, you're greatly appreciated!
Sent from my Dell Streak
Click to expand...
Click to collapse
I have read many posts recommending to install SetCPU (free if you search for it on XDA) and set the minimum speed to one setting higher than the default. Try it and post your results for others.

lordmorphous said:
I have read many posts recommending to install SetCPU (free if you search for it on XDA) and set the minimum speed to one setting higher than the default. Try it and post your results for others.
Click to expand...
Click to collapse
I do install a SetCPU already, and let the Scaling goes default with "smartass" from 1.9.1.
Currently the minimum speed is set 245760. And now I'm setting it to one-step higher which is 576000 and will see how it will work over the time.
Really thank you for this useful information, hope this will solve my "sleep" problem

Unfortunately, just now, my Streak is not responding to the power button while it's asleep with the setting of SetCPU to minimum speed of 576000 with Smartass Governer.
One thing I realized, the CPU Master Free which pre-installed with 1.9.1 is FC everytime I try to open it. Does this have something to do with my Streak not waking up?

coyle_Gyver said:
Unfortunately, just now, my Streak is not responding to the power button while it's asleep with the setting of SetCPU to minimum speed of 576000 with Smartass Governer.
One thing I realized, the CPU Master Free which pre-installed with 1.9.1 is FC everytime I try to open it. Does this have something to do with my Streak not waking up?
Click to expand...
Click to collapse
No, CPU Master Free FC's on mine as well, so its not just you

(InsertNameHere) said:
No, CPU Master Free FC's on mine as well, so its not just you
Click to expand...
Click to collapse
Hmmm, if it's FC then why DJ Steve include it in his ROM? >.<
Finally I uninstalled my SetCPU, and let's see if it solve my problem or not... *fingercrossed*

When there is setCpu installed with smartass governer and min speed of 576mhz, my streak randomly 'dead' when it's asleep.
Yesterday, i uninstalled setCpu, my Streak still 'dead'..
Out of my curiousity, tried to update the FC Cpu Master Free to last 1.9 edition from Market and it's working now. And now i'm trying my luck with the Cpu Master Free. If this time my Streak still 'dead', i really dont know what to do @[email protected]
Sent from my Dell Streak

Related

[Q] cannot wake up from sleep

Hi,
my new archos 101 often cannot wake up after sleep (deep sleep or screen timeout).
tried many methods: wifi disabled, battery booster, flight mode, sounds disabled... no luck.
i installed new fw, 2.1.8 and arctool with markets and google app and some games.
uninstalling maps and disabling wifi location didnt help. whats strange, is that sometimes screen turn on after 30s+ seconds..
i am new, but is there any way to check what's a process blocking it?
write to logs or connect via usb and check?
help very much appreciated
I'm having the same problem...
I just keep pressing the on/off button until the screen turns on. Didn't find a fix yet.
>>> i installed new fw, 2.1.8 and arctool with markets and google app and some games.
those were my 1st steps with archos, so dont know if it works in previous firmware.
right now, i dont want to do hard reset.
There is allready a discussion about this.
It seems that after the press, the archos is waking up, but the displaylight itself doesn't come up.
If you switch the display to abough 30% ( Settings/Display ) this doesn't happen again.
NOT kidding: the Archos has trouble turning on when cold. Try warming it on the radiator if its <15 degrees celcius.
Sent from my GT-I9000 using XDA App
success!
turned out, it is TRUE... 30% solved it!
btw, pretty ridiculous bug..
fzelle said:
There is allready a discussion about this.
It seems that after the press, the archos is waking up, but the displaylight itself doesn't come up.
If you switch the display to abough 30% ( Settings/Display ) this doesn't happen again.
Click to expand...
Click to collapse
30% of what? Increased brightness? I went to settings/display and couldn't find percentage level
As i don't have an english version, i can't tell you what you should read there,
but which other setting in display has percentages?
no % displayed, but just set if for 1/3 of the progress bar.
Jeezus, i cant believe it, but i can confirm that it's a brightness setting issue. It's so ridiculous but it's true. I have been frantically trying to find a solution to this problem for the past 30 mins, and turning the brightness setting to 40% worked to restore the screen after the soft sleep mode, when previously i had to keep rebooting the damn thing by longpressing the power button. THANKS A MILLION, GUYS!
Ohh i see i am not alone = ]
Thank you for the Workaround!
Sent from my A101IT using Tapatalk

Huge problem, please help me

Hello
My galaxy s2 doesnt wake up after put in to sleep mode, back n menu keys light up but no haptic feedback, while screen is on, no problems at all. please help me as ive tried wiping, reflashing different roms, trying multiple kernels and setting clock frequencies to always be on 1,2 ghz.
You must have something installed, like SetCPU and the phone goes below 200 MHz in powersave mode.
To all,
Please don't play with underclock/undervolt/overclock stuffs too much, it can damage the device big time. This is a phone for gods sake, keep playing with Sandy Bridge CPU's, they will take your tortures.
Regards.
I do have SetCPU installed, though i haven't touched the frequencies or voltages until after this problem which was when I put the frequencies to 1,2 gHz as lowest and highest. I have discovered another problem where TW launcher gets FC as soon as I touch the screen. Will try to uninstall SetCPU if I get the oppertunity.
wipe and then install cognition s2, its a modem rom and kernel all in one so you'll have no problems. then once its installed don't install setcpu
Sent from my GT-I9100 using XDA Premium App
Thank for your reply and all your help, I was insecure about custom roms so i installed stock rom amd it turned out great

Boot Loop and Android Reboots.

I bit the bullet and installed Cyanogen Mod Version 7 3.5 and the market. After one reboot back into Android and one into WebOs I ran into the Cyanogen Mod boot loop. Searched quite awhile on how to get out of this and found I had to do a hard reset by pressing and holding the power and home buttons. After I did this I booted into Android with no problem. But now when in Android the screen shuts off and soon after reboots. Anyone one know what might have caused this? How to fix this?
Edit: Did a couple of reboots with no problem. Turned off the Zen Live Wallpaper and that seemed to fix the reboot when the screen turns off. We shall see.
BigBadWolf84 said:
I bit the bullet and installed Cyanogen Mod Version 7 3.5 and the market. After one reboot back into Android and one into WebOs I ran into the Cyanogen Mod boot loop. Searched quite awhile on how to get out of this and found I had to do a hard reset by pressing and holding the power and home buttons. After I did this I booted into Android with no problem. But now when in Android the screen shuts off and soon after reboots. Anyone one know what might have caused this? How to fix this?
Edit: Did a couple of reboots with no problem. Turned off the Zen Live Wallpaper and that seemed to fix the reboot when the screen turns off. We shall see.
Click to expand...
Click to collapse
You may want to use SetCPU and set the min freq to 594mhz at least to prevent this reboot. The higher the less likely to reboot but may cause battery drain. Mine is set to max 1404 mhz / min 594 mhz / on-demand.
Link to SetCPU : http://forum.xda-developers.com/showthread.php?t=505419 free donate version but i bought it anyway to support this app.
anyway this is the wrong section but ...
Moved to general.
Sent from my NexusHD2 using xda premium

[Q] am i the only one?

am i the only one who experienced too much wake up delay?. i mean it took about 10-15 sec to wake it up. normally, when we press the home key, it'll wake up our ace within 1-2 secs, but in me it took 10 - 15 sec and i need to press the volume just to wake up my ace. i tried to reflash with odin, change my rom into cm 9, but no luck. what can i do to solve this problem?
Does it happens always? If so try setting min. frequency at 245 Mhz... Also governor to smartass v2
Prashanthme said:
Does it happens always? If so try setting min. frequency at 245 Mhz... Also governor to smartass v2
Click to expand...
Click to collapse
yes. it happens every time the screen turn off. i already did that, but nothing changed. i dont know what the problem of m ace
can someone tell me how to fix it?. it's really annoying. i always use my ace to check time, or check if there is any email, message received. but it always took about 10 - 15 secs to wake it up. dunno how did this happen to my ace. all i remember is i removed the sd card, then boom. it start to happen. and it always happen.
what is your internal memory free space and the RAM usage?
I also get the laggy problem when my dolphin browser is opened.
try RAM manager from pstore.
dianpadi said:
what is your internal memory free space and the RAM usage?
I also get the laggy problem when my dolphin browser is opened.
try RAM manager from pstore.
Click to expand...
Click to collapse
i have 83mb free in internal memory. dunno what is my RAM usage.. BUT, even if it is newly reflashed from odin, it still happens too much delay in wake up. so i try to flash a custom rom, CM 9 by mclaw, wipe the cache, wipe the delvik, restore factory settings, i already did all of them. but still, the the delay is there. 10-15 seconds delay in wake up..
how can i fix this?
I don't have this phone but i know it's related to the kernel
Sent from my LG-P500 using xda premium
FPChaim said:
I don't have this phone but i know it's related to the kernel
Sent from my LG-P500 using xda premium
Click to expand...
Click to collapse
i'll try to flash a new kernel.
EDIT: already tried to flash a new kernel. still no luck..
what rom are you using? cm variants have a known issue of having delayed wake up lags, and if you alread had tried flashing over odin try flashing over customized stock rom which are aboundantly found in the development section
maybe your phone using default min. frequency, if yes, change to 245 MHz
but in my case, my min-max freq is default, and it didn't affect my phone's wake up time
My screen off profile in SetCPU is 120Mhz Min and 320 at Max. I never had wake up problems in my phone. My question is, 15 seconds waiting is looong. Do you press just middle (HOME) button and wait for 15 seconds? Because in either case if you were/are on stock ROM flashed via ODIN. That must not be happening on stock.
If you're using CM based ROM, Is everything check in "buttons" section in Settings > CyanogenMod Settings > Input Settings?
I'm just checking which buttons you've assigned to wake up your device.
mawnstermew said:
what rom are you using? cm variants have a known issue of having delayed wake up lags, and if you alread had tried flashing over odin try flashing over customized stock rom which are aboundantly found in the development section
Click to expand...
Click to collapse
i already tried stock rom from odin, still it has the wake up extreme lag that took 10-15 secs. then i tried to flash custom rom, cm9, cm 7.1, 7.2, stock based rom, still no luck.. i think, it's the hardware of my ace that has problem.
Rushyang said:
My screen off profile in SetCPU is 120Mhz Min and 320 at Max. I never had wake up problems in my phone. My question is, 15 seconds waiting is looong. Do you press just middle (HOME) button and wait for 15 seconds? Because in either case if you were/are on stock ROM flashed via ODIN. That must not be happening on stock.
If you're using CM based ROM, Is everything check in "buttons" section in Settings > CyanogenMod Settings > Input Settings?
I'm just checking which buttons you've assigned to wake up your device.
Click to expand...
Click to collapse
i dont set any buttons to wake up my ace, means, it was using the default. even in stock rom flashed via odin, it still have the extreme lag wake up. i press the home button, the light turn on in the menu and back button (left and right of the home button), and if i just wait, it wont turn the lights on in the screen, sometimes, if i just wait the 15secs, it'll wake up and imediately sleep again bout less than 1 second. that's why i need to press the volume to wake it up
can someone know how to fix it?
Try to set Minimum Clock Frequency to 245 or flash Adrenaline Boost v2 then if you feel that you are running low on memory just give your Ace a Boost.
Sounds weird, but you mentioned earlier that you removed your SD card without unmounting? Try formatting the card and insert it when the phone is off OR erase it when in CWM recovery. Never know this might just work out. If it doesn't use Kies to update your phone to stock.(Tedious process I know). Hope it helps.
I'm surprised nobody thought of this as a hardware problem.
Do you still have a warranty?
consegregate said:
I'm surprised nobody thought of this as a hardware problem.
Do you still have a warranty?
Click to expand...
Click to collapse
my warranty is already void/expired. i really think that this is a hardware problem. because, i already tried what they said.. but nothing happens. still the same. i already tried to reflash again via odin twice. still got the extreme wake up delay. tried to flash a custom rom based on stock, still no luck, tried to flash a cm rom (7.1, 7.2, 9) still the same. tried to set the minimum frequency to 245, still the same. and i think, im the only one experiencing the 15 second wake up delay. that's why i think, it's the hardware that has the problem.
Xr01d_GT said:
Sounds weird, but you mentioned earlier that you removed your SD card without unmounting? Try formatting the card and insert it when the phone is off OR erase it when in CWM recovery. Never know this might just work out. If it doesn't use Kies to update your phone to stock.(Tedious process I know). Hope it helps.
Click to expand...
Click to collapse
i already did that. i think, it's not on SD. because it still happen with or without sd on my ace.

[Q] Strange touchscreen issue

I recently got a strange touchscreen issue.
When the device comes out of deep sleep (turn on the screen with power button) my touchscreen behaves weird. Normally, when I touch the unlock slider, it follows my finger. But not now....it's like long press is not recognized. I am able to unlock the screen by wiping my finger to unlock. But the slider is not following my finger. The strange thing is, after about 10 seconds, the issue is gone, and the slider follows my finger....
Also long press on the homescreen is not working during the first 10 seconds.
What I tried to solve:
I completely wiped the phone and reinstalled .42 firmware. Then updated tot ICS using Sony Update Service and also completely wiped my phone. The problem still there...then I flashed a custom ROM (shardur_seth spacious...and also his firmware) but the problem stille there.
Anyone else experienced this? Or any solutions I could try? It was there suddenly....could it be a hardware problem? But why is it gone after 10 seconds?
Thnx for your help
it happens for me sometimes, but most of the time when someone calling me i cannot at slide to answer. what im doing is i just press power button ones and it will silence and press the home key and it will work the slide key...
any solution for this also?
mavado said:
I recently got a strange touchscreen issue.
When the device comes out of deep sleep (turn on the screen with power button) my touchscreen behaves weird. Normally, when I touch the unlock slider, it follows my finger. But not now....it's like long press is not recognized. I am able to unlock the screen by wiping my finger to unlock. But the slider is not following my finger. The strange thing is, after about 10 seconds, the issue is gone, and the slider follows my finger....
Also long press on the homescreen is not working during the first 10 seconds.
What I tried to solve:
I completely wiped the phone and reinstalled .42 firmware. Then updated tot ICS using Sony Update Service and also completely wiped my phone. The problem still there...then I flashed a custom ROM (shardur_seth spacious...and also his firmware) but the problem stille there.
Anyone else experienced this? Or any solutions I could try? It was there suddenly....could it be a hardware problem? But why is it gone after 10 seconds?
Thnx for your help
Click to expand...
Click to collapse
i face the same problem
my phone is in service center for repair
see the video below and check if ur problem is the same
Sounds like your phone is just sluggish, you're probably running too much in the background/have too much installed on the phone and it takes a while for the RAM to optimally load everything you need again after having cleared some of it whilst the phone was in sleep mode.
SCHUMI_4EVER said:
Sounds like your phone is just sluggish, you're probably running too much in the background/have too much installed on the phone and it takes a while for the RAM to optimally load everything you need again after having cleared some of it whilst the phone was in sleep mode.
Click to expand...
Click to collapse
i repaired my phone via SEUS but the problem usa still there
went to service centre ,they downgraded it to Gb the problem was still there!!!!
dhwanik said:
i face the same problem
my phone is in service center for repair
see the video below and check if ur problem is the same
Click to expand...
Click to collapse
Yes, that's exactly the problem.....I also have the problem that I cannot longpress the home screen...U have the same issue? After 10 seconds or after tapping the screen multiple times, the issue is gone until the phone goes to sleep.
I too had this issue and narrowed it down to the sluggishness due to deep sleep.
What I did was,
1) Flash nightelf kernel
2) Installed Set CPU
3) Make profiles for Screen Off
4) Whenever I have the governor as "performance" I never had the issue
5) After lot of permutation combination, I fixed a screen off profile as 460max and 134 Min with conservative as governor.
6) Also added a new profile for "In Call" with "performance" governor.
The problem was gone. Yes, it happens once in a while but much better than the situation before.
mavado said:
Yes, that's exactly the problem.....I also have the problem that I cannot longpress the home screen...U have the same issue? After 10 seconds or after tapping the screen multiple times, the issue is gone until the phone goes to sleep.
Click to expand...
Click to collapse
yes i have the same issue we are not the only users who face this problem
there are many users who face this problem
arunsankar said:
I too had this issue and narrowed it down to the sluggishness due to deep sleep.
What I did was,
1) Flash nightelf kernel
2) Installed Set CPU
3) Make profiles for Screen Off
4) Whenever I have the governor as "performance" I never had the issue
5) After lot of permutation combination, I fixed a screen off profile as 460max and 134 Min with conservative as governor.
6) Also added a new profile for "In Call" with "performance" governor.
The problem was gone. Yes, it happens once in a while but much better than the situation before.
Click to expand...
Click to collapse
i am on locked boot-loader so can't flash kernel
arunsankar said:
I too had this issue and narrowed it down to the sluggishness due to deep sleep.
What I did was,
1) Flash nightelf kernel
2) Installed Set CPU
3) Make profiles for Screen Off
4) Whenever I have the governor as "performance" I never had the issue
5) After lot of permutation combination, I fixed a screen off profile as 460max and 134 Min with conservative as governor.
6) Also added a new profile for "In Call" with "performance" governor.
The problem was gone. Yes, it happens once in a while but much better than the situation before.
Click to expand...
Click to collapse
Tried using your settings..first I had governor set to performance...but the problem still persists. Wheneven I turn on the screen I have the issue. It is possible to unlock the screen if I wipe fast enough....but it really is strange...why is the issue gone after a couple of wipes or some touchscreen pressess..
Could it be a hardware error....a sensor not getting ready or something? But why is the problem gone when the screen is on for a while.....
mavado said:
Tried using your settings..first I had governor set to performance...but the problem still persists. Wheneven I turn on the screen I have the issue. It is possible to unlock the screen if I wipe fast enough....but it really is strange...why is the issue gone after a couple of wipes or some touchscreen pressess..
Could it be a hardware error....a sensor not getting ready or something? But why is the problem gone when the screen is on for a while.....
Click to expand...
Click to collapse
I have the same problem. Is there any solution?
Thank you for help.
same problem
Feri8850 said:
I have the same problem. Is there any solution?
Thank you for help.
Click to expand...
Click to collapse
me also having same problem and touch is awesome but when the lock is open then this problem will occur and it will open after 2 to 3 attempts..
what's this i think this is not an hardware problem this is only the software ??//??
i have the same problem too. i think there is a problem with cpu.
I had these sometimes with certain combinations of kernel and ROM. Actually it's gone... (Alliance V1/JJs Hybrid ROM 3.1)
I suppose it's a combination of hardware and software configuration...
Anyone tried to higher the minimum CPU speed?
Nachttier73 said:
I had these sometimes with certain combinations of kernel and ROM. Actually it's gone... (Alliance V1/JJs Hybrid ROM 3.1)
I suppose it's a combination of hardware and software configuration...
Anyone tried to higher the minimum CPU speed?
Click to expand...
Click to collapse
i tried. also i tried to set governor to different versions. and i tried nightelf rc5 kernel. nothing changed. problem still there.
today i realized that's not about only touchscreen. sometimes phone freezing.
problem with neo (mt15i) touch screen
use alliance night-elf v1.1 kernel.I had this problem but when I flash this kernel to my neo my touch screen works good same as the first day...
Well....for me suddenly the problem is solved!!!!
I'm very glad that my display is working again! It has been for about 3 months since I was facing the problem.
Unfortunately I do not have a clear solution to this, but I can explain what I did that day, and hopefully the solution is in there. But I can not garantee it.
What I did that day
1. I tried to get beats audio working, so I had installed a numerous of Beats libs. (see xda-developers for some of those libs). The last one I tried was Walkman port by ThilinaC. Not sure how this can be related to the display issue
2. I flashed a new rom. But this time I formatted /system and /data in CWM. Normally I just did a factory reset and installed the new rom. (but guess factory reset also formats /system and /data)
Still....guess this has nothing to do with the display
3. I did a offline charge. When my phone was empty I wanted to charge it fast. So I switched off my phone, and then connected the charger to offline charge the phone.
Really not sure how the above points could be a solution to de display failure, but guess if it was the digitizer that was the problem, it's strange that it is fixed out of knowhere....but the above actions are what I did that day....so maybe it's helpful and is the solution in there...maybe.
I'm glad the problem is gone
Yes, I am facing this exact problem, I am going to take my mobile to the service center !!!.

Categories

Resources