Hello Everyone!
Firstly I would like to say thank you for the amazing input you put into this site - I have gone *very* far on the path to learning about my PPC 6800 just from reading past posts.
Problem
When trying to use data services on a Sprint Mogul configured for Alltel - Dialing #777 results in a "Cannot connect for unknown reason" message.
Voice and Text works fine.
Current Setup
PPC 6800 - SPC Reset to 000000 via QPST
oliPro 2.4
Radio 3 42 50
DCD 3 2 6
Alltel Carrier Cab 20080824 (I simply double clicked to install this right?)
PRL: 30031 and 40036 tried
ALWAYS ROAMING (I'm never in an Alltel Area)
Windows Connections settings: Alltel Wireless - #777 - login: [email protected] pass: alltel domain: empty
My Flash Steps
1) hard reset
2) Installed olipro 2.4 (and even tried with no2chem 2 47) via RUU
3) Flashed alltel Stock 3.35.671.9 with Radio via RUU
4) Let customizations run
Data at this point does not work but has (last week!!)
5) install radio 3 42 50 via flash
6) install dcd 3 2 6 via ruu
7) let customizations run
8) double clicked on Alltel carrier 20080824 and installed to device
data says same problem
I've tried a *228 Option 2 (update roam) and Option 3 (activate). No help.
I'm stuck
EPST Settings
Security:
HDR AN: [email protected]
HDR AN pass: my hex esn in all caps
PPP user id: [email protected]
PPP pass: alltel
MIP Default:
nai: [email protected]
mn ha: 101
mn aaa: 3E8
reverse tunnel: enable
home address: 0.0.0.0
primary address: 0.0.0.0
secondary address: 0.0.0.0
ha shared: rzU4LCHIJp+Efdtf (it worked last week!?)
aaa shared: alltel
dmu public key: 0
mn authentication: 0
MIP
mip mode: mobile ip preferred
mobile node ha: disable
send reg retry: disable
dormant handoff: ena
QPST Settings
By putting my phone in DIAG mode and running QPST I have the following settings
DATA
MDR Mode: SVC opt 33 Prefd
Service option: Pre 707
Data qnc - unchecked
data scrm - enabled
Mobile IP
Behavior : simple only
mn auth calculation: unchecked
My Questions
1) am I flashing this correctly?
2) Could someone please verify what my DATA and M.IP settings should be in my QPST section?
3) does my HA shared key in EPST have anything to do with this?
Thanks for any guidance or help in getting me setup - I'm hoping that by making stating all my settings nice and clear we can help others that search in solving their problems as well!
ShaneOMak said:
Hello Everyone!
Firstly I would like to say thank you for the amazing input you put into this site - I have gone *very* far on the path to learning about my PPC 6800 just from reading past posts.
Problem
When trying to use data services on a Sprint Mogul configured for Alltel - Dialing #777 results in a "Cannot connect for unknown reason" message.
Voice and Text works fine.
Current Setup
PPC 6800 - SPC Reset to 000000 via QPST
oliPro 2.4
Radio 3 42 50
DCD 3 2 6
Alltel Carrier Cab 20080824 (I simply double clicked to install this right?)
PRL: 30031 and 40036 tried
ALWAYS ROAMING (I'm never in an Alltel Area)
Windows Connections settings: Alltel Wireless - #777 - login: [email protected] pass: alltel domain: empty
My Flash Steps
1) hard reset
2) Installed olipro 2.4 (and even tried with no2chem 2 47) via RUU
3) Flashed alltel Stock 3.35.671.9 with Radio via RUU
4) Let customizations run
Data at this point does not work but has (last week!!)
5) install radio 3 42 50 via flash
6) install dcd 3 2 6 via ruu
7) let customizations run
8) double clicked on Alltel carrier 20080824 and installed to device
data says same problem
I've tried a *228 Option 2 (update roam) and Option 3 (activate). No help.
I'm stuck
EPST Settings
Security:
HDR AN: [email protected]
HDR AN pass: my hex esn in all caps
PPP user id: [email protected]
PPP pass: alltel
MIP Default:
nai: [email protected]
mn ha: 101
mn aaa: 3E8
reverse tunnel: enable
home address: 0.0.0.0
primary address: 0.0.0.0
secondary address: 0.0.0.0
ha shared: rzU4LCHIJp+Efdtf (it worked last week!?)
aaa shared: alltel
dmu public key: 0
mn authentication: 0
MIP
mip mode: mobile ip preferred
mobile node ha: disable
send reg retry: disable
dormant handoff: ena
QPST Settings
By putting my phone in DIAG mode and running QPST I have the following settings
DATA
MDR Mode: SVC opt 33 Prefd
Service option: Pre 707
Data qnc - unchecked
data scrm - enabled
Mobile IP
Behavior : simple only
mn auth calculation: unchecked
My Questions
1) am I flashing this correctly?
2) Could someone please verify what my DATA and M.IP settings should be in my QPST section?
3) does my HA shared key in EPST have anything to do with this?
Thanks for any guidance or help in getting me setup - I'm hoping that by making stating all my settings nice and clear we can help others that search in solving their problems as well!
Click to expand...
Click to collapse
DMU Key Reset. Either activate an old phone... wait a bit... get it working... then re-activate the new one. Or... call them.... tell them your phone doesn't get data, and you just did a hard reset. They might be able to fix it for you while you are on the phone.
Case Closed!
I called alltel and asked them to look at at performing a DMU Reset - while looking at my account they realized a few glitches (why they did not catch it before I'm not sure) and made changes.
They included:
Updating my Service Class to Simple IP only
Double Checking my AAA Authentication log and realized that a billing issue was not connected (Damn, they should have left this alone )
Thanks for your help!!1
*case closed* !
Had a wi-fi problem on my htc desire for a while now..
One time I went to turn wi-fi on and it just said "Unable to start wi-fi". It had worked totally fine up until that point.
I've tried doing a factory reset, rooted, updated rom but it's still not working.
When the problem happened I had not rooted the phone or changed anything really.. it just happened.
In logcat it says:
flg=0x10200000 cmp=com.android.settings/.wifi.WifiSettings bnds=[124,404][236,531] }
D/SettingsWifiEnabler( 548): Received wifi state changed from Enabling to Unknown
W/SyncAllWidget( 151): activeSynch is null false
I/ActivityManager( 79): Displayed activity com.android.settings/.wifi.WifiSettings: 495 ms (total 495 ms)
I/WifiHW ( 79): wifi_load_driver enter
D/SettingsWifiEnabler( 548): Received wifi state changed from Unknown to Enabling
D/dalvikvm( 1805): GC freed 3806 objects / 257536 bytes in 97ms
D/NetworkLocationProvider( 79): onCellLocationChanged [1363,22890]
I/WifiHW ( 79): wifi_load_driver end error 2
E/WifiService( 79): Failed to load Wi-Fi driver.
D/SettingsWifiEnabler( 548): Received wifi state changed from Enabling to Unknown
Anyone got any ideas on how to fix this?
h2o pete said:
Had a wi-fi problem on my htc desire for a while now..
One time I went to turn wi-fi on and it just said "Unable to start wi-fi". It had worked totally fine up until that point.
I've tried doing a factory reset, rooted, updated rom but it's still not working.
When the problem happened I had not rooted the phone or changed anything really.. it just happened.
In logcat it says:
flg=0x10200000 cmp=com.android.settings/.wifi.WifiSettings bnds=[124,404][236,531] }
D/SettingsWifiEnabler( 548): Received wifi state changed from Enabling to Unknown
W/SyncAllWidget( 151): activeSynch is null false
I/ActivityManager( 79): Displayed activity com.android.settings/.wifi.WifiSettings: 495 ms (total 495 ms)
I/WifiHW ( 79): wifi_load_driver enter
D/SettingsWifiEnabler( 548): Received wifi state changed from Unknown to Enabling
D/dalvikvm( 1805): GC freed 3806 objects / 257536 bytes in 97ms
D/NetworkLocationProvider( 79): onCellLocationChanged [1363,22890]
I/WifiHW ( 79): wifi_load_driver end error 2
E/WifiService( 79): Failed to load Wi-Fi driver.
D/SettingsWifiEnabler( 548): Received wifi state changed from Enabling to Unknown
Anyone got any ideas on how to fix this?
Click to expand...
Click to collapse
I have the same problem on a ROM i have made... That's just for Tattoo not Desire... But it's the same logcat... So can somebody help us??
Yeah I'm pretty stuck on what to do :/.
Added some information about my software to the first post.
i have same problem on my htc dream
BUMP...
-------------------------------------
Sent from my übercharged HTC Tattoo
Fixed it by setting a static IP address.
Wi-Fi > Menu Button > Advanced > Use static IP
i had yesterday the same problem on my desire,
i fixxed this with flash a "older" stock rom and update it with the build-in updater....
same problem with my desire. how to fix it?
It's broke again. Setting a static IP doesn't fix it any more. Any ideas?
got the same problem here
can any one help???
Bump
Sent from my HTC Desire using XDA App
seems like wlan.ko is not available in /system/lib/modules/
I've had similar problems in the past, but was unable to solve them. You can check several things though.
1) wlan.ko in /system/lib.modules <-- has to match up with the kernel that you are using
2) any entries for wifi and/or dhcp in the init.rc and init.devicenamehere.rc files that are in the ramdisk in the boot.img
3) wifi settings in the build.prop
4) files in /system/etc/wifi
5) I'm not sure about this one, but even some of the files in /system/etc/firmware might have something to do with wifi.
6) files in /system/etc/dhcpd
7) any files in /system/bin and/or /system/xbin that are called by *.rc from #2.
Just take a working ROM (stock is usually what I use), and compare the files with the corresponding files in your build. I use either WinMerge or N-way Folder Compare or just plain old 'diff' in Linux.
I had the same issue.
Flashed a new ROM with full wipe etc. Wifi OK.
Flashed a kernel update on top of the ROM. Wifi broken. Turning wifi on it would error and turn off again.
The only way I could fix it was to flash a full ROM and make sure I wiped everything from the recovery.
Any more info you can provide? Current ROM +version +any other mods applied like status bar or OC kernels?
Did anyone fix this?? I am stuck here, G1 Dream
CM 5.0.8 DS
Please help!!!
Are you getting the same error in logcat as others have? If so, I think .mak fixed it, but he never let us know how.
Same Issues...
Ive tried Reverting to CM 5.07, 5.07 and now the beta 6.0 and all have yet to fix the wifi issue. I also tried switching between the radio's and doing a full format/partition and wipe. Any fix to this yet?
That was Lovely Bro...Really Useful...I got my DESIRE today and could connect to WIFI but was unable to browse...This tip helped me...Thx a lot... Keep up the good work..
Trying to replace bcm4329.ko
I did the OTA update for my Desire today, and of course have the wi-fi problem.
However, when I enable wi-fi, I see the following appear at the end of dmesg:
Code:
<3>[ 8197.511535] bcm4329: version magic '2.6.32.15-g6a358a9 preempt mod_unload
ARMv7 ' should be '2.6.32.15-gf9c0527 preempt mod_unload ARMv7 '
The update zip (via thread 778852) contains a bsdiff patch file patch/system/lib/modules/bcm4329.ko.p... and from some examination of that file it appears just to patch the vermagic field of the .ko file.
I tried to use a hex editor to 'fix' bcm4329 and used adb pull/push to replace it, but I get
Code:
failed to copy 'bcm4329.ko.fix' to '/system/lib/modules/bcm4329.ko': Read-only
file system
Can anyone help me with this?
Update: I am a fool. I was using the wrong goldcard! Once I put the right goldcard in, then sdcard:update.zip applied correctly and wi-fi started working again.
@dleonard, could you please make step by step instructions of how to fix this wifi issue?
thanks
Mixu
My school runs a network with the settings detailed here:
* Network Name (SSID): UMASS-SECURE1X
* Authentication Mode: WPA2 Enterprise
* Encryption Type: AES
* Authentication Method: PAP
* EAP Type: EAP-TTLS
I had no problem connecting to the school network until i installed Froyo (AXURE 2.1). I tried 3 different roms (Onyx, Axure, Stock) and nothing can connect to the school network. If it means anything when ever i go in to edit the network settings the network stays as a TTLS but the second auth changes back to none.
is there a fix and is this a known issue?
already discussed here
if you cant find your specific problem start a new thread
Guys need help.
I was using my photon in India with Reliance CDMA till recently EVDO started having issues with respect the the speed of download. Now the speed issue is resolved but i am not able to download any Apps from google play store.I have again Flashed 198_7 using RSD lite (Now completely stock with locked bootloader and rooted).
But still no luck. When ever i try to download any apps it shows as downloading but without any actual download happening.
It works for sometime when i try to do a factory reset but stops working after few mins. Google play store download happens perfectly on Wifi or1X but with EVDO it fails ?
After seraching a bit in net I have tried clearing the cache for google play store and google service framework but it did not help. even tried with other google account also with the same issue
I tried running logcat and found only few observations given below
12-17 07:30:06.708 W/NetworkStateTracker( 1626): net.tcp.buffersize.evdo not found in system properties. Using defaults
12-17 07:30:06.708 V/NetworkStateTracker( 1626): Setting TCP values: [65536,131072,262144,65536,131072,262144] which comes from [net.tcp.buffersize.default]
12-17 07:30:06.708 D/NetUtils( 1626): failed to add 220.224.141.145 as default route for ppp0: File exists
12-17 07:30:06.768 I/PollingManager( 2097): connectivity_action: NetworkInfo: type: mobile[CDMA - EvDo rev. A], state: CONNECTED/CONNECTED, reason: apnSwitched, extra: cinet.spcs, roaming: false, failover: false, isAvailable: true
12-17 07:30:06.858 E/SYS_MPP ( 2134): ProxySettingHandler Can not get preferred APN id
12-17 07:30:12.498 W/PackageManager( 1626): Unknown permission android.permission.READ_OWNER_DATA in package com.motorola.blur.socialmessaging
12-17 07:30:12.518 W/PackageManager( 1626): Unknown permission com.android.email.permission.READ_ATTACHMENT in package com.motorola.certificatemanager
Any configuration issues or is there any issues with my handset Please help...
After few more testing following are the observations.
Status in settings - about phone shows as connected to EVDO Rev A
*#*#4636#*#* also shows as connected to EVDO Rev A
Speed test app shows a download speed of 1 mbps with ping time of around 120 ms
Except speed test none of the other app (including browsers)are able to access the EVDO BW i believe.
Even i tried connecting my laptop to mobile by making mobile as hot spot that time also the speed i am getting is only around few kbps..
Yesterday night again tried few factory reset without any help.
(Asuming all drivers are installed and you have a hotspot plan or you are able to use hotspot with no problems)
Android 2.3.6
4.5.141.MB860.Att.en.US
Phone connected to usb and USB tether turned on, computer not connected to internet
Windows is connected to "Unidenfied Network" and there's no internet access. You must set manually ip.
open command promp and execute "adb shell ifconfig" (or android terminal on phone and execute ifconfig)
Find interface "usb1"
[*]Find "inet addr" and write somewhere the value (mine is 192.168.42.129)[*]Find "Mask" and write somewhere the value (mine is 255.255.255.0)
Click on network icon, Open Network and Sharing Center.
At the left, click "Change adapter settings"
Right click on the atrix network adapter (find a network adapter with the text "remote NDIS adapter..."; select "Properties"
Click on "Internet Protocol Version 4"
Click in "Properties" button
Click on "Alternate Configuration"
Click on "User Configured"
IP Address: Pick an ip address. Same value as phone except for last number (if phone ip is 192.168.42.129 you could pick 192.168.42.130 for example)
Subnet mask: Same as Phone (mine is 255.255.255.0)
Default Gateway: same ip addres as phone
Prefered DNS Server: 208.67.222.222
Alternate DNS Server: 208.67.220.220
You can also use Prefered DNS Server: 8.8.8.8 and leave alternate in blank
Click ok and save/apply changes
Wait a while and windows will connect to phone and internet will work
------------------
Also if mobile hotspot not working change current apn settings and delete "apn type".