I got 2461 with stock rom @ 1Ghz
I got 2376 with stock rom @ 1gh via quadrant advanced...
pretty much same , 24xx ... bye the way, what is your choice on governer? interactive or ondemand?
I've gotten about 26xx to 27xx
Sent from my GT-P7510 using xda premium
Mine is 12".
I got 2916 with stock @1.4Ghz
After 1.4Ghz 3800+
Sent from my GT-i5800 using XDA Premium
_delice_doluca_ said:
pretty much same , 24xx ... bye the way, what is your choice on governer? interactive or ondemand?
Click to expand...
Click to collapse
Performance...
Sent from my GT-i5800 using XDA Premium
2950 [email protected]
longlong240 said:
After 1.4Ghz 3800+
Sent from my GT-i5800 using XDA Premium
Click to expand...
Click to collapse
3800+? How did you get that high?
I'm running SGT 10.1 rooted/In Parisv4/Pershoot's kernel and OC @1.4 or so I thought. I read this and opened Quadrant Standard. Ran it and got 1829. I noted this was about the same as those running at 1Ghz and knew something wasn't right. I went into SetCPu and checked "set at boot" rebooted the tab, and my scores are now much betta:
2941
3069
3069
3063
not bad, but based on the advice in the SETCPu setup guide and my experience as an original/gangster of PC overclocking (Celery Sandwich will likely tell my age) this not be any issue at all, for the SGT10.1, but if you start seeing weird ()&(^$# THEN BACK IT DOWN, RINSE, REPEAT AT A LOWER FREQUENCY, if the problem can't be reproduced there it's likely due to instability between frequencies of CPU and main memory. Bottom line step your oclock up slowly until you hit repeatable instabilities/errors/crashes, and then back it down.
Anyone know off the top of their head an app to monitor the temperature of the CPU? I get the battery temp from inside Set CPU along with a lot of great info except my CPU temp, which is typically important for OC'ers.
Related
I flashed 1.2.2 rom first than I flashed bcblend kernel. Rebooted everything seems to work fine except I do a quadrant benchmark test and im getting low scores. When I go in set cpu and oc to 1.7 max .8 min i get high benchmark scores like I had with stock kernel. Anybody know whats happening? I unocked htcdev method. Hboot 1.5 with s-on
Are these low benchmark scores reflecting actual performance? If not, then don't care too much about it.
Are you using SetCPU, or a daemon?
Sent from my PG86100 using XDA App
DDiaz007 said:
Are these low benchmark scores reflecting actual performance? If not, then don't care too much about it.
Are you using SetCPU, or a daemon?
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
I'm using setcpu. No performance is superfast...It's like my phone smoked crystal meth, no matter what I set the CPU speed to. Regardless I'm getting low bench scores. But I'm gonna take your advice and not care about it. I was just wondering if that was normal for a custom ROM and kernel combo.
Jabawockee said:
I'm using setcpu. No performance is superfast...It's like my phone smoked crystal meth, no matter what I set the CPU speed to. Regardless I'm getting low bench scores. But I'm gonna take your advice and not care about it. I was just wondering if that was normal for a custom ROM and kernel combo.
Click to expand...
Click to collapse
Try setting the min freq as the same as max. Then select the performance governor, and run a bench. See what that does.
Sent from my PG86100 using XDA App
DDiaz007 said:
Try setting the min freq as the same as max. Then select the performance governor, and run a bench. See what that does.
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
Okay, I set it at 1.6 ghz min and max on demand. Then I ran the antutu bench test. My score barely passed the galaxy s2. Is that normal? Performance wise its real fast though so i dunno if I should be concerned???
Jabawockee said:
Performance wise its real fast though so i dunno if I should be concerned???
Click to expand...
Click to collapse
Absolutely no need for concern. Benchmark scores are terribly overrated. if the phone feels fast, then ride with it.
Hey guys I just started overclocking my ace and i must say i am seeing a difference in performance. Now a bit more details:
ROM: Stocklite V6
Using No Frills CPU Control (which came with the ROM)
So far my settings for the highest clock is:
MAX clock freq: 864mhz
Governor: performance
I/O sch: deadline
Should I keep pushing for a higher clock speed or is that good enough, and what are the signs of an unstable OC, i've been playing angry birds after each OC, also going on the market and downloading stuff, is that enough or should I run something else?
I know the minimum clock speed recommended for the ace is 245mhz, right now i'm just trying to get the highest clock speed, when I attain the highest clock speed, which governor would you guys recommend, on demand or smartass?
Try smartass v2
Use zimage which has multi overclock option
And keep min 245
And Max 902
Sent from my GT-S5830 using xda premium
Thanks man, i'll give it a go now and report back.
HUMM...just tried 883mhz and within 2mins of playing angry birds the phone rebooted...i guess I will have to live with 864mhz...but still it's a good OC, everything feels much more.....crisp
Study about the CPU governors before you start using them. Performance governor uses the MAX CPU clock @ ALL THE TIME, Uses the hell of a battery. & SGA is meant to be working on 800 max at all the time, it was running 864 continuously. No wonder why your phone rebooted. Continuous OCs will hamper your phone life.
amd-dude said:
HUMM...just tried 883mhz and within 2mins of playing angry birds the phone rebooted...i guess I will have to live with 864mhz...but still it's a good OC, everything feels much more.....crisp
Click to expand...
Click to collapse
Yea well,but dont get into the habit of overclocking it every time or.......you will suffer the same thing i am suffering now
Prawesome said:
Yea well,but dont get into the habit of overclocking it every time or.......you will suffer the same thing i am suffering now
Click to expand...
Click to collapse
What are you suffering from?
shailpancholi said:
Try smartass v2
Use zimage which has multi overclock option
And keep min 245
And Max 902
Sent from my GT-S5830 using xda premium
Click to expand...
Click to collapse
Zimage max is 800..
Sent from my GT-S5830 using XDA
syed.sayeed96 said:
Zimage max is 800..
Sent from my GT-S5830 using XDA
Click to expand...
Click to collapse
Ya by he should hv better kernal like the one with 902mhz
Its awesome and then use zimage then yummy will ft option
Sent from my GT-S5830 using Tapatalk 2 Beta-4
shailpancholi said:
Ya by he should hv better kernal like the one with 902mhz
Its awesome and then use zimage then yummy will ft option
Sent from my GT-S5830 using Tapatalk 2 Beta-4
Click to expand...
Click to collapse
Please, please, PLEASE. Don't use that gibberish writing style. Use normal english, as we all try to do (I think a very few of xda users speak english as a native language, as well).
Jar3112 said:
Please, please, PLEASE. Don't use that gibberish writing style. Use normal english, as we all try to do (I think a very few of xda users speak english as a native language, as well).
Click to expand...
Click to collapse
i can say that u speak for all of us. and u can read minds!
I'm not going to leave the governor on performance, I was just using it to let the phone run all out while OC'ing, I have enabled the Smartass V2 governor now and all is good. Now i'm finding the lowest clock speed where everything still moves smoothly. So far 320mhz is pretty decent..jittery but decent.
guys, which kernel i can use for a good overclock? I am using zImage-Mod v1.5 more i can´t overclock with this..
leo4b said:
guys, which kernel i can use for a good overclock? I am using zImage-Mod v1.5 more i can´t overclock with this..
Click to expand...
Click to collapse
Ketuts OLD one... i could do 960 with that..
Sent from my GT-S5830 using XDA
Prawesome said:
Yea well,but dont get into the habit of overclocking it every time or.......you will suffer the same thing i am suffering now
Click to expand...
Click to collapse
what u suffering???
mine since last 3 month until now 24h oc..320 min 902 max using ketut kernel..
please share what u suffering...
If i OC mine beyond 844 MHz my phone restarts
Dont think that if one person gets 902 or 920, that you will be able to as well
test each stage carefully. IMHO OC isnt worth it (im happy with max 800)
I'm currently on The Unofficial v1.5 and supposedly it supports overclocking up to 1.9 ghz. Has anyone else using this rom noticed that when you raise the clock speed that high it just reboots constantly? Its supposed to be able to support it, so have I done something wrong?
Sent from my SAMSUNG-SGH-I717 using xda premium
tmb993 said:
I'm currently on The Unofficial v1.5 and supposedly it supports overclocking up to 1.9 ghz. Has anyone else using this rom noticed that when you raise the clock speed that high it just reboots constantly? Its supposed to be able to support it, so have I done something wrong?
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Most kernels say 1.9 but u should stay at 1.83. 1.9 creates bootloop
Sent from my SAMSUNG-SGH-I717 using xda premium
Yes...it does bootloop alot at that speed.. the safest speed is 1.83 or even 1.89 that's plenty of enough speed without any problems...
tmb993 said:
I'm currently on The Unofficial v1.5 and supposedly it supports overclocking up to 1.9 ghz. Has anyone else using this rom noticed that when you raise the clock speed that high it just reboots constantly? Its supposed to be able to support it, so have I done something wrong?
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
1.94 os max speed if u read it says 1.83 stable
sent from team perfections ics rom
The max speed on any device is always unstable. Actually most of the time the top two or three speeds ar always unstable. It also depends on the device too. My Note and your Note may not be stable at the same speed and the rom has nothing to do with it, its the chip in your phone. I remember I had a Touch Pro 2 once that most people could only over clock to 710MHz but a few of us could overclock to 786MHz. I have my Note running pretty stable at 1836 but I have seen some people complaing about bootloops at that speed so it really depends on your device. Remeber when testing out clock speeds make sure that you never check "Apply At Boot" in case the speed is not stable and only check it when you find a stable speed. Her's a video of someone running stable at 1890MHz
http://www.youtube.com/watch?v=g4hd5jG1ztc
porkenhimer said:
The max speed on any device is always unstable. Actually most of the time the top two or three speeds ar always unstable. It also depends on the device too. My Note and your Note may not be stable at the same speed and the rom has nothing to do with it, its the chip in your phone. I remember I had a Touch Pro 2 once that most people could only over clock to 710MHz but a few of us could overclock to 786MHz. I have my Note running pretty stable at 1836 but I have seen some people complaing about bootloops at that speed so it really depends on your device. Remeber when testing out clock speeds make sure that you never check "Apply At Boot" in case the speed is not stable and only check it when you find a stable speed. Her's a video of someone running stable at 1890MHz
http://www.youtube.com/watch?v=g4hd5jG1ztc
Click to expand...
Click to collapse
Ur right its called a hot reboot
sent from team perfections ics rom
Thanks guys. Been running solid at 1.83 ghz. Min around 702 MHz. Battery lasts almost all day. Anyone found better settings for battery life?
Sent from my SAMSUNG-SGH-I717 using xda premium
tmb993 said:
Thanks guys. Been running solid at 1.83 ghz. Min around 702 MHz. Battery lasts almost all day. Anyone found better settings for battery life?
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Yes. Leave it at 1.5max and 192min. If you're not doing anything that requires oc'ing, why set it high.
would that cm9 1.5 ?
if so , where are you over clocking from ?
babymatteo said:
Yes. Leave it at 1.5max and 192min. If you're not doing anything that requires oc'ing, why set it high.
Click to expand...
Click to collapse
It runs sooo much smoother overclocked. But ill try what you said.
Sent from my SAMSUNG-SGH-I717 using xda premium
tmb993 said:
Thanks guys. Been running solid at 1.83 ghz. Min around 702 MHz. Battery lasts almost all day. Anyone found better settings for battery life?
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
384 min 1836 max is the best one use lagfree on setcpu
sent from team perfections ics rom
JB calhoun said:
384 min 1836 max is the best one use lagfree on setcpu
sent from team perfections ics rom
Click to expand...
Click to collapse
Is it true that 384 is the minimum samsungs can run? I used to have my atrix down to 192 and it worked fine (tegra 2)
Sent from my SAMSUNG-SGH-I717 using XDA
erick161 said:
Is it true that 384 is the minimum samsungs can run? I used to have my atrix down to 192 and it worked fine (tegra 2)
Sent from my SAMSUNG-SGH-I717 using XDA
Click to expand...
Click to collapse
No it can go down to 192
Sent from my SAMSUNG-SGH-I717 using xda premium
Just a tip if you overclock your CPU it will drain the battery life faster keep this in mind.....
The unofficial v1.5 rom came with an OC tool. If I downloaded another one, say SetCPU, will it just override the native tool?
Sent from my SAMSUNG-SGH-I717 using xda premium
tmb993 said:
The unofficial v1.5 rom came with an OC tool. If I downloaded another one, say SetCPU, will it just override the native tool?
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
I don't know is because i never rooted my device and i know im missing out a ton of features im going to keep stock for a while is because i like how my phone works at the moment.
Sent from my SAMSUNG-SGH-I717 using XDA
animeware said:
I don't know is because i never rooted my device and i know im missing out a ton of features im going to keep stock for a while is because i like how my phone works at the moment.
Sent from my SAMSUNG-SGH-I717 using XDA
Click to expand...
Click to collapse
If you have no idea and you don't root phones then why are you even here?! Talk about pointless...
Sent from my SAMSUNG-SGH-I717 using xda premium
I want to know what's the safe overclocking maximum and governor . I also want to know what's the maximum safe temperature? Is 50c' as a maximum safe? Thanks for your help.
Sent from my SK17i using xda premium
theres no such tthing as safe oc.
each and every cpu had different characteristic thus different capability when it comes to oc. what might works with others might just hardbrick yours. you just need to experiment yourself. do note thats its dangerous. earlier one guy already fried his phone when oc to 1.8ghz+playing gta3.
and for me personally 45c feels too hot already.
an0nym0us_ said:
theres no such tthing as safe oc.
each and every cpu had different characteristic thus different capability when it comes to oc. what might works with others might just hardbrick yours. you just need to experiment yourself. do note thats its dangerous. earlier one guy already fried his phone when oc to 1.8ghz+playing gta3.
and for me personally 45c feels too hot already.
Click to expand...
Click to collapse
I know what you mean. You are right of course. Mine is overclocked to 1.3ghz governor smartassV2 and the max temp for overclocking is my problem now. I can't decide what is the max temp at which the phone should go back to 1ghz . Do you think 45c' as a maximum safe?
Sent from my SK17i using xda premium
then use any app that can create profile to automatically lower cpu freq based on temperature eg cputuner or setcpu.
an0nym0us_ said:
then use any app that can create profile to automatically lower cpu freq based on temperature eg cputuner or setcpu.
Click to expand...
Click to collapse
I'm already using CPU master pro . I created a profile for overheating but I don't know what is the maximum temperature that I should use?
Sent from my SK17i using xda premium
I'd say 45° MAX. Or even less. And still you can't be 100% sure you won't have any problem.
Feanor88 said:
I'd say 45° MAX. Or even less. And still you can't be 100% sure you won't have any problem.
Click to expand...
Click to collapse
I've set it to 43" . Hoping that I don't screw my device
Sent from my SK17i using xda premium
Hello all!
I hope some of you like numbers as much as I do. I thought I should run my handset through a series of benchmarks in order to see just what the dev community has unlocked within this device.
Here we go:
Overclocked to 1.72 GHZ - Governor: Performance
Cubed Kernel 1.2.5
Genome ROM v2
BenchmarkPi:
Average of 5 - 337.4 ms
Best of 5 - 224 ms
Linpack:
Average of 5 - 463.059 MFLOPS
Best of 5 - 510.427 MFLOPS
ANTUTU:
Average of 5 - 18396
Best of 5 - 19270
Vellamo:
HTML5 -- 1737
Metal -- 636
Quadrant:
Average of 3 - 8131
Best of 3 - 8364
These results put the Droid DNA well ahead of pretty much all competition for the next few months. I imagine things will get even better once AOSP Roms make their way to this amazing device.
So - does anyone with a higher overclock have any stats? I would be interested in seeing how well this processor scales.
That quadrant seems low. I've gotten 8254 stock unrooted.
Sent from my HTC6435LVW using xda app-developers app
sent from my beastly powered DNA using Tapatalk 2
DSB's Cubed v 1.2.5
Sent from my HTC6435LVW using xda app-developers app
getting there...
DSB and UKB's latest
System Tuner Pro to take it up a notch or two
How did you get 9608 I got 8660 on quadrant with 1.83 gh cubed latest
Sent from my HTC6435LVW using xda app-developers app
Ndaoud360 said:
How did you get 9608 I got 8660 on quadrant with 1.83 gh cubed latest
Sent from my HTC6435LVW using xda app-developers app
Click to expand...
Click to collapse
The benchmarks usually don't turn on all the cores. At least that's what I think because I turn all my cores on and all on the performance governor and I get around the 9500's at 1.83Ghz.
I've received over 9k quadrant and 500+ linpack with 1.5ghz. Strangely, powersave gave me better scores than performance (stock kernel)
On cubed kernel 1.5ghz performance = 587
http://imgur.com/u4N5w
Whats the next step in mobile processing? How fast or powerful can they be?
iOSh8er said:
DSB's Cubed v 1.2.5
Sent from my HTC6435LVW using xda app-developers app
Click to expand...
Click to collapse
23345 cpu! Holy fruck!
Sent from my EVO using xda premium
I love this phone
Sent from my HTC6435LVW using xda premium
I managed to break the mystical 10k marker on quadrant.
I've been more of a lurker, until now.
Anyway, this is with cores set at 1890x4, performance governor setting. Running senseless ROM.
I'd like to thank everyone on XDA for their work on android.
neatojones said:
I managed to break the mystical 10k marker on quadrant.
I've been more of a lurker, until now.
Anyway, this is with cores set at 1890x4, performance governor setting. Running senseless ROM.
I'd like to thank everyone on XDA for their work on android.
Click to expand...
Click to collapse
By the way, while my phone is stable on these settings it drains my battery too fast to be usable. I leave the cores set to 1890, but as long as I don't have the setting on "performance" I actually see decent battery life. My quadrant drops into the upper 9k's though without the governor set to performance.
neatojones said:
I managed to break the mystical 10k marker on quadrant.
I've been more of a lurker, until now.
Anyway, this is with cores set at 1890x4, performance governor setting. Running senseless ROM.
I'd like to thank everyone on XDA for their work on android.
Click to expand...
Click to collapse
You are the chosen one my friend. No, but really... dayyuummmnnn!
neatojones said:
I managed to break the mystical 10k marker on quadrant.
I've been more of a lurker, until now.
Anyway, this is with cores set at 1890x4, performance governor setting. Running senseless ROM.
I'd like to thank everyone on XDA for their work on android.
Click to expand...
Click to collapse
Cheers for breaking 10k but why is your I/O score so low? (I've got 15k+ on the Note 2) Also was expecting the 3D score to be a lot higher on the DNA, kernel doesn't have support for GPU OC? IMO with those CPU / MEM and tweaking 11000-11500 should easily come
tbukkos said:
Cheers for breaking 10k but why is your I/O score so low? (I've got 15k+ on the Note 2) Also was expecting the 3D score to be a lot higher on the DNA, kernel doesn't have support for GPU OC? IMO with those CPU / MEM and tweaking 11000-11500 should easily come
Click to expand...
Click to collapse
True. I could probably have a done a little more tweaking on the I/O score. The kernel used for this does support GPU OC, but I haven't found a tool that I feel comfortable using to OC the GPU yet. That and probably more realistically: I moved on to conquering other things once I managed the 10k score that was my goal.