Related
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
kameisama said:
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
Click to expand...
Click to collapse
Time to take it in and get a new one.....
Same problem here phone started b not coming out of lock mode. Backlight is on but no display on screen (if i tilt the screen left and right i can see light coming from behind) did about 6 hard resets and still same problem. also power button works whenever it wants to. this phone sucks @ss, i want my mogul back. on a second note my replacement will be here on wednesday.
Touch Pro stock rom purchased back in nov when it came out
yeah, i've had the same problem, i found if i hit my phone on the back or side and then batter pull and hit the soft reset while off, not the power button to turn it back on, it comes back on with color on the screen not just blank black screen with backlight, this works mostly every time, but when it doesn't, i just hold the power button down and do battery pull and hit the power button and it works, its like its got a combo of things you have to do before it works.. weird
Boot Up
I have also had similar problems. I for some reason sometimes have to remove my SD card and boot up without it for some reason. Not all the time, but every once in a blue moon. Not too sure how that affects anything, but you may try that too.
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Mayonesa said:
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Click to expand...
Click to collapse
Have you tried re flashing the ROM?
it wasnt HTC's fault for your phone's not booting...thats what happens when u try to mess with the hardware too much and you dont know what your doing
Would you want to sell???
Reboot Brick HTC process
****DOn't take battery out after hard boot***
1.just watch videohttp://www.youtube.com/watch?v=sk56olMkCtU and do what they do but dont take battery out. LEAVE phone STUCK on BOOT screen. Nothign else will move or work but you want phone just like that.
2. connect usb cable to active sync. (this may not link up but leave usb connected anyhow) Do not delete phone profile.
3.use rom like Download MightyROM6_Herman.exe avail at: http://www.lilrico.com/Mighty/mightyromblog/?p=454
4 although active sync is still attatched but may not be connecting. It will connect thru usb anyway when you run the rom software. http://www.youtube.com/watch?v=fV2I2WAFkg4&NR=1
This worked and kept phone from cutting on and off. and restored ROM. don't know about original htc boot. but your phone will work under this rom for now and you can go from there.
hey thanks plain ole dumb, it works now.
man I thought it was over.
thanks again
Hi guys. I'm totally new to the android/smart phone world btw. Anyways, I recently got my Samsung Galaxy S2... first thing I noticed, my touch screen wasn't working. I popped the battery in and out and then it started working as it should.
My phone was working fine this morning, then all of a sudden out of no where, the touch screen stopped working again. I've tried turning on/off the phone multiple times. I've taken out the battery and even my SIM card nothing... i'm worried.
Has this happened to anyone else? Is there a fix? Do i have to go through Samsung? I hope not. Incase anyone asks, I did not root my phone.
Any help/feedback would be appreciated.
When the touchscreen stops working... were you charging the phone at that time?
The first time i turned on my phone, was actually by accident and it was charging.
However, just earlier now, it was not. it was just sitting on my computer desk. The home button, lock button and touch capacitive buttons work.... but i can't get past the lock screen
you could try a factory reset to see if its software related, but it sounds like hardware. I would definitely Return the phone .
I guess I can't do a factory reset, since I can't get into any of the menus... man this sucks. I spent $900 *gulp*
To do a factory reset,
1. Turn the POWER OFF, pull the battery out and put it back again.
2. Simultaneously press and hold the Volume Up, Home and Power button
3. If the Samsung Symbol appears, release the Power button
4. A Boot Menu will then show, Use the volume up/down to choose wipe data/factory reset.
touch screen not needed this way.
oo that's interesting... I tried it. and it didn't get to a boot menu. maybe I was doing it wrong. I tried a few different ways, but no success. It turns out I have warranty with the store. They're going to replace it for me Thanks for the feedback guys. Awesome forums.
Something similar happened to me yesterday. When I had the in-box USB cable attached to a BoxWave VersaCharger (combined AC/DC charger), and the VersaCharger was plugged into 120V AC, the touchscreen would stop working. As soon as I unplugged the USB cable from the SGS2, or plugged the VersaCharger into a 12V DC lighter socket, the touchscreen would work fine.
I've got the same problem as the OP... I had my phone charging overnight and this morning when I first went to use the phone I could not unlock the screen. I could wake the screen via the home button, and see I had a missed call etc but it just wasn't responding to touch. BTW I can't remember if when I first tried to unlock the phone if it was charging or not but really this shouldn't matter.... oh and btw, I'm not rooted or anything either! Naturally I rebooted the phone but still the same problem....so I tried a battery pull and still the same problem. Just now I did a factory reset but the touch screen still isn't working! I guess this is a hardware problem so I'm going to get it fixed under warranty by Samsung! Gutted that I will likely be without my phone for a week or 2!
EDIT, UPDATE...
Well, I was just on my way to the repair shop Samsung warranty had told me to take it too, and I took my sim card out to put in my old Hero (the only thing I hadn't tried!) and I couldn't believe it but the touch screen started working fine again! Weird, but that is now my advice if anyone else has a problem with their touch screen not working - oh and I took the sim out whilst the phone was still turned on. Crisis averted!
UPDATE 2
Sadly this has happened about 4 times to me now and I'm just waiting for the inevitable next time. Each time doing a factory reset then taking the sim card out seems to bring the screen back to life (though last time not immediately) but I shouldn't have to put up with this. Problem is, I don't want to send off a seemingly perfectly working phone to get repaired as I fear they will struggle to notice the problem, never mind fix it! I'm hoping a new firmware comes out soon, in the hope that it may resolve my issues...
Me as well ...
I have had this happen to me twice now (Touchscreen not responding).
The first time I had just installed a game and thought it must have been related to that. Pulled the battery and no joy, left it for a while and it came back to life...
Second time I was surfing the web and it stopped responding, pulled the battery and left it for maybe a minute but no joy .... pulled the battery again and left it for probably 20min and it came back to life. When it came back up I noticed the livewallpaper had been turned off and my widgets were gone from the homescreen.
What I did notice when it wasn't working was it had "safe mode" displayed at the bottom left of the screen
Have the Same Problem
Have the same problem i Mine and was super exicedat first it worked fine and after charging the touchscreen stopped working i pulled the battery out and put it back in but no luckso im gonna return mine to the shop hope they replace it
Moral:AT FIRST SUPER EXICTED BUT NOW SUPER ANGRY
Same issue - Is there ANY way to save my data before I send it in for repair/replace?
Hi all,
As of this morning, I have exactly the same issue as the OP. Screen doesn't react to touch, with the exception of the capacitive buttons. I found a dude on YouTube that had the same issue: youtu.be/0oIdllWiV4I
The last thing I did with the phone before it started misbehaving was to answer a call. The phone was on the charger when the call came in - I can't recall whether I unplugged it before answering, or after, or at all during the call. Not sure it has any relevance anyway, only mention it because I've seen reports of people's screens no longer reacting to touch when the phone is plugged in to a charger (apparently it even states in the manual that this may happen).
Anyway, whilst all my contacts, SMS, photos etc are backed up to the cloud, the same can't be said for my app data. Before I lose hours and hours of progress in various games, or all my settings in numerous other apps, etc, can anyone think of any way to get access to the memory of the phone, bearing in mind the following:
I can't connect to Kies to pull a back-up because bluetooth is currently enabled on the phone and when one connects the USB cable, it says "Activating USB mode will deactivate Bluetooth. Continue?" but I can't click the Yes button
I can't connect in USB mass storage mode because I can't navigate to the settings menu entry to enable it
I can't turn Bluetooth off in order to get Kies working, becuase I can't get to the settings menu or pull down the notification bar to reach the power control.
I can't use Voice input to control the device (on the off chance there was a "bluetooth off" voice command) because (presumably with the most recent firmware I flashed via Kies a few weeks back) for some reason Vlingo is no longer the app on the double-home button action. Instead it calls Samsung Voice and wants to walk me through a first use tutorial, but I can't click the next/skip buttons
I installed via Android Market push the app belonging to www_remoteaccessphone_com as it promises to be able to remotely switch bluetooth off, but the website says I haven't installed the app yet, presumably because alrhough I was able to install it without touching the phone, it probably needs to be run at least once to set it up, and I obviously can't do that
I can't start Kies Air to try and get my data that way (starting it would require using the touch screen)
Kies via bluetooth isn't supported on Android
Needless to say, the data I'm trying to retrieve is on the internal memory, not the SD card. As you can see I've been trying all sorts of creative things, but I'm fairly sure I'm screwed. Any bright ideas I haven't thought of?
blaubeer said:
Hi all,
As of this morning, I have exactly the same issue as the OP. Screen doesn't react to touch, with the exception of the capacitive buttons. I found a dude on YouTube that had the same issue: youtu.be/0oIdllWiV4I
The last thing I did with the phone before it started misbehaving was to answer a call. The phone was on the charger when the call came in - I can't recall whether I unplugged it before answering, or after, or at all during the call. Not sure it has any relevance anyway, only mention it because I've seen reports of people's screens no longer reacting to touch when the phone is plugged in to a charger (apparently it even states in the manual that this may happen).
Anyway, whilst all my contacts, SMS, photos etc are backed up to the cloud, the same can't be said for my app data. Before I lose hours and hours of progress in various games, or all my settings in numerous other apps, etc, can anyone think of any way to get access to the memory of the phone, bearing in mind the following:
I can't connect to Kies to pull a back-up because bluetooth is currently enabled on the phone and when one connects the USB cable, it says "Activating USB mode will deactivate Bluetooth. Continue?" but I can't click the Yes button
I can't connect in USB mass storage mode because I can't navigate to the settings menu entry to enable it
I can't turn Bluetooth off in order to get Kies working, becuase I can't get to the settings menu or pull down the notification bar to reach the power control.
I can't use Voice input to control the device (on the off chance there was a "bluetooth off" voice command) because (presumably with the most recent firmware I flashed via Kies a few weeks back) for some reason Vlingo is no longer the app on the double-home button action. Instead it calls Samsung Voice and wants to walk me through a first use tutorial, but I can't click the next/skip buttons
I installed via Android Market push the app belonging to www_remoteaccessphone_com as it promises to be able to remotely switch bluetooth off, but the website says I haven't installed the app yet, presumably because alrhough I was able to install it without touching the phone, it probably needs to be run at least once to set it up, and I obviously can't do that
I can't start Kies Air to try and get my data that way (starting it would require using the touch screen)
Kies via bluetooth isn't supported on Android
Needless to say, the data I'm trying to retrieve is on the internal memory, not the SD card. As you can see I've been trying all sorts of creative things, but I'm fairly sure I'm screwed. Any bright ideas I haven't thought of?
Click to expand...
Click to collapse
flash it with CF-root, boot into CWM recovery, do a nandroid backup after that, use CWM recovery again to mount USB storage, connect to your PC and pull everything off.
Nitrile said:
flash it with CF-root, boot into CWM recovery, do a nandroid backup after that, use CWM recovery again to mount USB storage, connect to your PC and pull everything off.
Click to expand...
Click to collapse
Thanks for the quick advice. I guess I'll need to use my girlfriend's phone to download CF-root and then transfer the SD card to my device. Quick question before I proceed though - is it possible to remove all traces of such tampering, since I've already made out with Samsung that I'm sending it in for repair, and I'm not sure they will honour the warranty if they see it has been rooted etc.
blaubeer said:
Thanks for the quick advice. I guess I'll need to use my girlfriend's phone to download CF-root and then transfer the SD card to my device. Quick question before I proceed though - is it possible to remove all traces of such tampering, since I've already made out with Samsung that I'm sending it in for repair, and I'm not sure they will honour the warranty if they see it has been rooted etc.
Click to expand...
Click to collapse
get a USB jig off ebay or amazon to reset the flash counter. should not cost more than 5 or 6 euros, shipped.
anyways you need to flash CF-root through ODIN if you are coming from stock. instructions are all in chainfire's cf-root thread.
Nandroid Restore
So I successfully rooted, used CWM to do a Nandroid backup, mounted the sd_card and saved the contents (including the nandroid backup) to my PC, reflashed the stock rom & kernel, usb-jigged it to get the counter back to zero/original and sent the phone in for repair. My efforts paid off as they repaired it without question under warranty. I just received the phone back and today set about restoring my backup:
Copied the sd_card contents I'd saved to my HDD back onto the phone
Re-roooted it with Cf-mod.
Used CWM to restore the backup I took before sending it in
It restored boot/system/data/cache successfully
selected reboot now in CWM
The result is that it is still missing all my apps. It only seems to have the "data" like my camera shots and SMS messages, system settings like whether bluetooth is on or off, the volume level, Wifi networks etc. So something was restored. But there is no Google Account configured, the lock screen picture is the default not the one I had beforehand, and as I said, all the apps - the main reason I did this whole thing as my personal data is all backed up to the cloud on a regular basis anyway - have not been restored. Am I confused? I thought a nandroid backup took a complete snapshot of everything, apps included.
Finding out the list of Apps I had in order to reinstall them is not an issue - I have a list of everything I had installed saved on AppBrain. But if I reinstall the apps, all the settings (or progress in the games) within those freshly installed apps will be back to square one, not where I left them, right? Or should I reinstall the apps and then restore the data partition over the top again?
Are you guys using any type of screen protectors, cause if you are, that may be the issue s their have been reports that the screen becomes unresponsive with certain screen protectors when connected to a charger.
However, if you are not using a screen protector, then I would suggest getting the unit replaced as you should not have to do anything, root or otherwise, to get the touchscreen working on a touchscreen phone
achillies400 said:
Are you guys using any type of screen protectors, cause if you are, that may be the issue s their have been reports that the screen becomes unresponsive with certain screen protectors when connected to a charger.
However, if you are not using a screen protector, then I would suggest getting the unit replaced as you should not have to do anything, root or otherwise, to get the touchscreen working on a touchscreen phone
Click to expand...
Click to collapse
Nope, no screen protector or any kind of case for that matter. Anyway, that isn't my issue anymore. The touch-sensitive unit was defective, the phone was repaired under warranty. My issue now is getting my apps & settings back. I have meanwhile read elsewhere that Nandroid doesn't back up the apps - pretty deceptive "backs up everything!" "it is like time travel" etc comments around here then.
Anyway, I reinstalled all the apps I had previously, and thought by reapplying the data partition from the nandroid backup it might then bring back the settings for the reinstalled apps. Instead all it did was remove all those apps again - now I am really confused. How come the restore DOESN'T bring back the apps I used to have, but DOES remove the ones I subsequently install. Does Nandroid touch the apps or doesn't it?
Touch screen not working
So i am having a very peculiar problem related to the GT-I9100 Touch Screen.
I bought the phone from Saudi Arabia and I live in Bangladesh at the moment. So for now I don't have warranty.
I bought it on 4th of this month. It had 2.3.3. So I updated it to 2.3.5. I did not use the phone much before that so I don't know if this problem was there before.
So here is the problem.
First time I noticed it when i pulled the phone from my pocket and could not unlock the pattern. First I thought I forgot the pattern. After sometime I noticed that i could not touch the buttons. I was dragging my finger over the points but there was no connecting line. I restarted the set. But it still did not work. After sometime I took the battery out. And after that it started normally and unlocked. And the touchscreen is totally fine.
I tested it using *#0*#. And every single point in the screen registers touch.
After that this happened couple of times. First couple of days I thought it was a pattern unlock problem. But i tried PIN and Password even using no unlock. It happened in every case.
So after couple of days it totally stopped happening.
But from yesterday it is happening again. And today it happened 3 times.
So today as I had no unlock protocol i tried tapping Home twice. As this brings on the voice command menu. And for the first time i was in the phone without touching the screen.And first i noticed the Menu and Back Soft keys works.And the touchscreen still does not work. And i noticed some thing weird. Always some thing in the screen is Selected. In Menu the + Icon is selected. In first screen the Map icon is selected. Also in Recent Apps the first App is selected. So after a lot of reboots it is back to normal again. Now i see something interesting. In the Battery Usage Graph i can see some really sharp drops. 3 times. Looks like when this happens phones charge takes a nose dive.
So here is the Gist.
Info related the Problem:
1. Usually happens when the phone is my pant pocket for sometime. It does not happen if it is sitting on the table.
2. Touchscreen gets totally disabled.
3. I have no idea why this happens.The exact reason behind it.
4. Battery Charge takes a nose dive when this happens. See the attached images.
5. I still don't know how to bring it back. Sometimes a simple reboot works. Sometimes I have to pull the battery. And sometimes it works on its own.
6. Every other function of the phone works. Like music playback using my UE 200vi music keys using PowerAMP, Siri(Android version), Call can be received using headset.
Battery nose Dive:
dl.dropbox.com/u/30943431/SC20111115-203017.png
dl.dropbox.com/u/30943431/SC20111116-202913.png
Also the selection
dl.dropbox.com/u/30943431/SC20111116-202146.png
So this is the thing. My biggest problem right now is, I don't know why it happens and I don't know how to bring it back from this situation. If I knew I could make sure I don't get it again or I would just fix it every-time. As when this happens I cant make calls or anything which requires the touchscreen.
So guys help me if you can by giving ideas. As i will not go back to KSA in 6 months. So buying a $550 phone unlocked was a total waste. As i cant use it here.
Thanks a million in advance.
---------- Post added at 09:29 PM ---------- Previous post was at 09:13 PM ----------
Sorry for this. But looks like i cant post outside links before i have 8 posts. So i removed the "ht tp : //" part of the links. Copy paste in browser address bar and it will open fine.
And also the next time it happens i will do a video to shou you guys.
Having the same problem while charging touch screen doesn't work
Stock charger and usb cable
i was on CM7 but that happend so i flashed stock but no luck
I will write more observations
Hey guys,
I know there has been a couple of posts like this that I have found through searching but none have actually found a solution, so instead of resurrecting a old thread I thought I would start a new one.
Basically I am having some issues with my new pebble blue (yey) S3 . I have found that sometimes when the phone is sleeping when I press the power button to bring it out of sleep the lock screen begins to hang. This is followed by a number of different things, the screen either glitches for a bit and then begins to work or it stays locked and needs a battery pull. As well as this I've found that randomly either when charging or not and the phone is sleeping it simply becomes unresponsive, staying on a black screen and needing a battery pull to fix (this has only occured a few times, the hanging lock screen occurs quite often).
I have done some searching and found little in the way of a solution or what the problem is, however I have found that when the lock screen hangs -if it begins to work again after glitching out the 'WIFI connected to ****' appears at the bottom of the screen. Anyway if anyone has any ideas or also recieves this problem I would really appreciate some help as it's driving me crazy and I'm unsure if it is a common S3 bug or a faulty handset, in which case I have limited time to RMA.
Cheers in advance
Hmm, sounds like a faulty phone to me. Try taking it back to get it exchanged for onother one. S3 was built to fly not crawl.
You'll want to go through a process of elimination to figure out when might be causing it.
Something you can try and test with (one at a time)
-turn on airplane mode
-turn off live wallpaper
-shut down all running tasks
-change your lock screen security method
-limit the number of widgets running on all the screens
-reduce the number of active screens
Probably other things you can try to pull out of the equation, but thats a good start
After looking up dial-a-phones returns policy it would seem that I have 28 days to return if the handset is faulty, so this atleast gives me some breathing room to try out any suggestions for fixes. I will begin to eliminate each of the suggested items above however as the lock screen problem is intermittent it make take a day so actually see if it has had an effect, which is annoying at the least.
On another note a numberupted of people are stating high battery life on their devices however mine doesn't seem to be as good and I do have power saving on as well as nfc etc. turned off. This makes me believe my handset could have a fault, but tbf I haven't allowed for a discharge to 5% and the recharging to 100% which I heare allows for optimisation of the battery.
EDIT**** I have changed the lock screen previously and found it had no effect on the problem and I do not have a live wallpaper in use.
Phone Freezing after reboot and auto wifi signal found on.
Same here, been happening the last few days after I installed Avast. Also, turning off and on the auto on wifi seemed to replicate the problem.
The phone will boot to the lock screen and freeze a bit, and sometimes the news ticker freezes, and then after unlocked, I try to turn off wifi signal has been found on the notification dropdown and then tries to auto connect to wifi, the phone will freeze up if I dont turn it off in time.
Once the auto wifi connect is off and reboots, then the phone will keep glitching up until it catches up processing alot of processes it was trying to do for about 1/2 hr. Also, if phone freezes up for too long, like after trying too many time of unlocking the screen while freezing up, the phone gets stuck at the lock screen and the phone almost overheated, in an area right below the battery. I had to pull the battery out to cool it off.
It seems to be a glitch in the auto wifi, especially if alot of resources are being used. Once Avast was on my phone about 1.5GB RAM is being used sometimes and since has really slowed the phone down. Going uninstall alot of apps.
JCrinage said:
Hey guys,
I know there has been a couple of posts like this that I have found through searching but none have actually found a solution, so instead of resurrecting a old thread I thought I would start a new one.
Basically I am having some issues with my new pebble blue (yey) S3 . I have found that sometimes when the phone is sleeping when I press the power button to bring it out of sleep the lock screen begins to hang. This is followed by a number of different things, the screen either glitches for a bit and then begins to work or it stays locked and needs a battery pull. As well as this I've found that randomly either when charging or not and the phone is sleeping it simply becomes unresponsive, staying on a black screen and needing a battery pull to fix (this has only occured a few times, the hanging lock screen occurs quite often).
I have done some searching and found little in the way of a solution or what the problem is, however I have found that when the lock screen hangs -if it begins to work again after glitching out the 'WIFI connected to ****' appears at the bottom of the screen. Anyway if anyone has any ideas or also recieves this problem I would really appreciate some help as it's driving me crazy and I'm unsure if it is a common S3 bug or a faulty handset, in which case I have limited time to RMA.
Cheers in advance
Click to expand...
Click to collapse
Same problem.
No problem if Wifi is switched off prior to sleep.
No problem if Wifi connection is still available.
Problem to lockscreen if Wifi connection is broken (move away from connected router).
Any suggestion?
sassorock said:
Same problem.
No problem if Wifi is switched off prior to sleep.
No problem if Wifi connection is still available.
Problem to lockscreen if Wifi connection is broken (move away from connected router).
Any suggestion?
Click to expand...
Click to collapse
Exactly the same here. Driving me crazy. I did root the phone using the Samsung Galaxy S3 Toolkit. I don't know if the problem also exists on non rooted devices.
S3 black screen after unlocking
Has there anyone experience S3's screen went on black? I have pebble blue S3 - GT-I9300. Cases when unlocking, answering an incoming call or attempting to turn off an
alarm? Mine happens when after unlocking the screen then it goes black and screen becomes unresponsive. It happens intermittently and even after 3 times of
reprogramming. I am now going to have it replaced. I am having a lot of troubles -- it exits on its own when im reading or composing an SMS; files were deleted after
restarting the unit, and an app opens up even not touching the scree. This is expensive and I am paying a lot just to experience this king of inconvenience.
DavidNieuwpoort said:
Exactly the same here. Driving me crazy. I did root the phone using the Samsung Galaxy S3 Toolkit. I don't know if the problem also exists on non rooted devices.
Click to expand...
Click to collapse
I also rooted my S3 a few days ago (with the S3 toolkit), and have had lots of problems with unresponsive lockscreens (I use PIN, because of exchange connection). It takes a few seconds or maybe up to as long a minute before I'm able to punch in the PIN-numbers. Before this the screen lights up but does not respond to input.
But the WiFi-connection issue might be what is the triggering factor, because after a boot it wotks just fine for several hours, if I'm not moving out of my current WiFi zone. First I thought it was either Secure Settings or Tasker that made my device lock up in this matter, but now as they are both uninstalled, the problem still occurs.
Are you running some kind of custom rom, or just the latest stock ROM, but rooted?
Flodas said:
I also rooted my S3 a few days ago (with the S3 toolkit), and have had lots of problems with unresponsive lockscreens (I use PIN, because of exchange connection). It takes a few seconds or maybe up to as long a minute before I'm able to punch in the PIN-numbers. Before this the screen lights up but does not respond to input.
But the WiFi-connection issue might be what is the triggering factor, because after a boot it wotks just fine for several hours, if I'm not moving out of my current WiFi zone. First I thought it was either Secure Settings or Tasker that made my device lock up in this matter, but now as they are both uninstalled, the problem still occurs.
Are you running some kind of custom rom, or just the latest stock ROM, but rooted?
Click to expand...
Click to collapse
Just the latest stock ROM but rooted. I've found out that turning off the wifi power safe mode fixes the problem for me. To do this:
- In the dailer enter *#0011#
- Press the menu key
- Select wifi
- Press the on/off button.
The wifi power safe mode will however be turned on during boot. So rebooting will set it back on.
*#0011# seems does the trick. But is annoying had to do this every time after power off (change battery, change Sim, flying).... Anyway to keep the setting?
I am also on stock Rom and rooted. Interested to know any non-rooted phone got this problem?
BTW. I found a quick (at least quicker than pull the battery) way to get out of the forzen lock screen (sometimes forgot to do the 0011 trick): press the power button (screen will Dim instead of OFF), then hold the home button for few seconds, as soon as you see the "menu" and "back" button lit up, the lock is un-freeze...
A permanent solution is appreciated for such an advance phone....
sassorock said:
*#0011# seems does the trick. But is annoying had to do this every time after power off (change battery, change Sim, flying).... Anyway to keep the setting?
Click to expand...
Click to collapse
Not that I know of.
Problem solved. For me anyway. Hope works for all of you having the same trouble.
My trouble begin with recent upgrade to LH3. My S3 was rooted by S3 toolkit v2.0. CWM installed was v4 something.
I un-rooted the phone. Uninstalled S3 toolkit v2.0. Re-installed the S3 Toolkit v5.0. Rooted the phone again (CWM become v6....).
I do not know it was CWM version caused the trouble or not. But my S3 is ok now.
I got it on my non-rooted phone, any additional solutions/suggestions? or service?
I found solution for problem . And my phone is working well. I downloaded rom file android 4.1.2 and flash my phone
JB 4.1.1 caused these WiFi issues on my phone
Jodatnia said:
I found solution for problem . And my phone is working well. I downloaded rom file android 4.1.2 and flash my phone
Click to expand...
Click to collapse
Exact opposite for me...never had the problem then since loading stock JB 4.1.1 with root I get lockups or freezes whenever WiFi is turned off or I leave my router's range. As soon as I disconnect from WiFi the whole phone freezes.
The *#0010# also locks up the phone when I turn off the WiFi power saving feature.
None of this happened before JB...and I replaced my phone with week via warranty due to this and the new phone does the exact same thing as soon as I upgraded to JB with root.
Any ideas?
Black screen / random reboot solution
Hi All,
I've had the black screen / random reboot issue for a few days. The only way to restore functionality on black screen lockup was to remove the battery.
I tried changing to Chrome browser and stopping the stock browser as suggested in some threads but it kept crashing.
I searched everywhere and most threads suggest a dodgy motherboard.
For me the issue was related to either a single PDF download via the stock browser or the fact I had quite alot of saved PDF files on my phone (S3 Stock firmware I9300XXELLA)
After deleting all the files listed in Internet downloads (look for Downloads with a green arrow Icon in apps) my trusty S3 has returned to normal. No black screen lockups, no hanging, runs like a dream!
I appreciate this may not solve everyones black sceeen issues but I haven't found any other thread with this solution. Hope it works for you.
Thanks,
Giz.
giz_zard said:
Hi All,
I've had the black screen / random reboot issue for a few days. The only way to restore functionality on black screen lockup was to remove the battery.
I tried changing to Chrome browser and stopping the stock browser as suggested in some threads but it kept crashing.
I searched everywhere and most threads suggest a dodgy motherboard.
For me the issue was related to either a single PDF download via the stock browser or the fact I had quite alot of saved PDF files on my phone (S3 Stock firmware I9300XXELLA)
After deleting all the files listed in Internet downloads (look for Downloads with a green arrow Icon in apps) my trusty S3 has returned to normal. No black screen lockups, no hanging, runs like a dream!
I appreciate this may not solve everyones black sceeen issues but I haven't found any other thread with this solution. Hope it works for you.
Thanks,
Giz.
Click to expand...
Click to collapse
Thanks for the tip...
Was this happening on JB for you? You mention stock firmware (not familiar with I9300)...so I am guessing it was ICS.
For me the issues are with JB and I had no files at all in the Downloads folder after a certain point when I wiped / formatted the SDCard...so I do not think my lockups were related to PDFs. But I did (and still do) have a ton of music and a lot of movies on the External MicroSD Card....and quite a few custom notification and ringtone MP3s on the Internal SDCard. Next time I load JB I will run it a few days with none of this media loaded....
Jodatnia said:
I found solution for problem . And my phone is working well. I downloaded rom file android 4.1.2 and flash my phone
Click to expand...
Click to collapse
For me this also worked. Resolved everything. (on i9300 int)
Boomer6345 said:
Thanks for the tip...
Was this happening on JB for you? You mention stock firmware (not familiar with I9300)...so I am guessing it was ICS.
For me the issues are with JB and I had no files at all in the Downloads folder after a certain point when I wiped / formatted the SDCard...so I do not think my lockups were related to PDFs. But I did (and still do) have a ton of music and a lot of movies on the External MicroSD Card....and quite a few custom notification and ringtone MP3s on the Internal SDCard. Next time I load JB I will run it a few days with none of this media loaded....
Click to expand...
Click to collapse
This is on JB 4.1.2, Phone had been updated to 4.1.2 for about a month. The issues started after a pdf download. Once all pdf's were deleted the handset works perfectly.
Giz
SGS2 I9100 with Ressurection Remix ICS_v2.4_AOKP-B39-4.0.4
Device was working fine, battery was low (<5%) so i connected my charger; went to sleep, woke up and tried to turn display on - couldn't ... i thought that maybe phone was battery dead when i connected it so i long-press the power button to start it up but nothing was happening.
Disconnected the charger, took out the battery, waited 20s then put it back, connected charger and tried to power on => sgs2 splash screen .... .... ... showing desktop screen w/o icons and after 5-10s device shows "Shutting down" vibrates and shuts down.
Rebooted into CWM recovery, reinstalled ROM => no change
Rebooted into CWM, wipe data/factory reset => no change
Any ideeas what is going on? is the battery malfunctioning?
Try a new battery in the first instance. If it still happens once you've done that then we can look at other causes. Also, if you feel so inclined, do a clean install of stock & see if that fixes the issue to rule out something in your current setup (rom/kernel/etc) causing the problem.
thanks, been thinking the same about trying another battery but that is something i cannot do today
MistahBungle said:
Try a new battery in the first instance. If it still happens once you've done that then we can look at other causes. Also, if you feel so inclined, do a clean install of stock & see if that fixes the issue to rule out something in your current setup (rom/kernel/etc) causing the problem.
Click to expand...
Click to collapse
tried another battery, same.
flashed a stock, os load doesnt pass "S" screen
also i recharged battery on another phone and when i use it in mine, it gets drained quickly
guess the problem is the "power supply"
First, I would have posted this in the development forum but I don't have enough posts to do that...
I have the NC5 bootloader with SS 3.72 and flashed Albe95 S6 FULL PORT 4.6 to the stock slot after wiping it. First time it booted up it went to a completely black home screen with only the signal, time, and battery percentage showing. Then shortly after it showed a "system UI is not responding" or similar message. Pulling the battery and rebooting fixed this. Overall, the rom has been working great since then despite the following minor issues:
1. Lost cell signal a few times with "no service" message. Last time this happened was a few minutes after a fast reboot and entering airplane mode and back again fixed it.
2. Screen rotate doesn't work sometimes, but a reboot seems to fix this. I should also note that I usually turn my rotate off and only turn it on when I need it, but the last few times it hasn't worked on demand and I had to reboot to correct this.
3. Proximity sensor doesn't work (as others have reported) when on a call.
On the plus side, whereas others have reported problems with their hotspot function, mine has been working great and activating it doesn't seem to cause other issues. I have an android headunit in my car and I use trigger on the phone to activate my hotspot when my phone connects to my headunit via bluetooth, it turns it off again when I get out of the car. So I use it a lot and haven't had problems.
Keep up the good work guys! Let me know if I can help test or help out somehow. I'm not a programmer but I do have almost 20 years of IT experience.