Related
So i dropped my phone and looks like i need a new digitizer. I have tear down the phone and the last thing i need to do is remove the digitizer but i have no idea on how to do it. Does anyone have any tips or links that show you how to remove it? I've seen this video http://www.youtube.com/watch?v=t8u5Wa3Odak but it doesn't show how to remove the digitizer. Any help would be really appreciated
Painkiller006 said:
So i dropped my phone and looks like i need a new digitizer. I have tear down the phone and the last thing i need to do is remove the digitizer but i have no idea on how to do it. Does anyone have any tips or links that show you how to remove it? I've seen this video http://www.youtube.com/watch?v=t8u5Wa3Odak but it doesn't show how to remove the digitizer. Any help would be really appreciated
Click to expand...
Click to collapse
At the end it shows you to heat up the digitizer to losen the adhesive that is holding it in place all around the edge. After that, slowly pry around. Do it really slowly though and let it work itself off, and don't use a sharp object because it will damage the sensitivity of the digitizer. Really patience is key. Don't rush it like I tried to the first time also be careful of the lcd underneath.
Just to reiterate what was already said, pry very gently, don't stick whatever pry tool you are using too far into the device, the LCD below will crack so easily. I did it when I did mine. Have patience, take a lot of time slowly working it off the adhesive little bit by little bit. There isn't any magic trick to this, it takes a lot of time and practice.
So, I see only one other thread about this, but I dropped my phone (Clumsy me left it on a chair, it slid off, and spider webbed my phone(SUCH a short distance)) But, I've bought the replacement part myself, and I plan on doing the repair myself. Is there anything I should know before I actually do this? Has total disassemble of the phone been done before?
Not to hijack your thread, but it drives me nuts how my LGOG seems to seek out-on its own-a way to dive off my coffee table/sofa/end table...no matter how flat and non inclined I sit it two seconds later and...CRASH! floor time...luckily mine has been taking it ok. So I feel your pain, and hope you get the help you seek.
Sent from my LG-E970 using xda premium
bqd37340 said:
Not to hijack your thread, but it drives me nuts how my LGOG seems to seek out-on its own-a way to dive off my coffee table/sofa/end table...no matter how flat and non inclined I sit it two seconds later and...CRASH! floor time...luckily mine has been taking it ok. So I feel your pain, and hope you get the help you seek.
Sent from my LG-E970 using xda premium
Click to expand...
Click to collapse
I even know your feeling -.- I've never dropped it before though, that was my first time, mostly because I treat my phones like its my second life, and because theyre expensive. This phone dropped literally a foot and webbed, I was so mad
Dr Protostar said:
I even know your feeling -.- I've never dropped it before though, that was my first time, mostly because I treat my phones like its my second life, and because theyre expensive. This phone dropped literally a foot and webbed, I was so mad
Click to expand...
Click to collapse
Found this video off a quick google search...
jtsurfs said:
Found this off a quick google search...
Click to expand...
Click to collapse
I've seen that video, but it doesn't really show how to put the replacement back in, if you use glue, what type of glue, or how much heat is required and all that such
Dr Protostar said:
I've seen that video, but it doesn't really show how to put the replacement back in, if you use glue, what type of glue, or how much heat is required and all that such
Click to expand...
Click to collapse
I replaced the digitizer on an HTC Vivid and used 3m double sided tape and doubled that up so the screen wasn't directly on top of the lcd. The video for that one recommended doing that to keep some weird effects on the screen.
given heisbig
jtsurfs said:
I replaced the digitizer on an HTC Vivid and used 3m double sided tape and doubled that up so the screen wasn't directly on top of the lcd. The video for that one recommended doing that to keep some weird effects on the screen.
Click to expand...
Click to collapse
Whats the youtube vid name?
Maybe try some silicone glue
Maybe try some of the silicone seal (blue silicone glue) to attach it. If nothing else you might try some electronic stores (specialty or other Cell phone repair stores) for the glue that is needed. I would opt for something that isn't so hard on stuck and maybe go for something that holds tight and seals well but doesn't make it damn near impossible.
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
If you get the lcd and digitizer together, you can fix yourself and it's easy just as star master says. If you have a shop nearby they can replace just the glass
Sent from my SCH-I545 using xda app-developers app
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How much do you think it would go for on ebay? (or somewhere else) I didn't think a damaged phone would be worth selling?
That phone is still with over $200 as is.just the good motherboard alone. Especially if it had a clean imei number..then counting other parts of the phone too
Sent from my SCH-I545 using xda app-developers app
Good tutorial how to fix it
There is some kind of double side transparent adhesive between LCD and digitizer. So good luck
Opened front glass
Hi, I opened front glass of Mega 5.8 to clean the dust inside it. When I put it back, the touch is not working. Earlier it was working perfectly, I did not remove any cables. Also that I cleaned it with dry cloth while the phone was on.
What may be the issue?
warriorpluto said:
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How does it separate?
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Did you get it?
ReyesARG said:
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Click to expand...
Click to collapse
I wonder how was it going with your repair?
http://www.witrigs.com/samsung-galaxy-mega-replacement-parts
Adhesive is a problem
letus1 said:
I wonder how was it going with your repair?
Click to expand...
Click to collapse
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
If i separated the digitizer and the glass ftom the lcd, than can i bound the new one with LOCA or will that damage the LCD?
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
I knew that was the only way to do it, with hot plate and fishing pole string. I'm sure it's a slow process. I'll have to invest in a good hot plate.
Sent from my SM-N900V using xda app-developers app
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
VirtueToVice said:
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
Click to expand...
Click to collapse
What kind of griddle? This is the one without the edges right?
Sent from my SM-N900V using xda app-developers app
starmaster10 said:
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
Click to expand...
Click to collapse
I like this..
fixxforyou said:
May i ask how much for this glass?
Click to expand...
Click to collapse
Who give your answer ? Mention it..
I have had my Ultra Z since January. Zero problems, but this morning I removed my USB charger at work and a rubber gasket (see pic) fell out. Now the door does not close properly. I have the gasket and tried to work it back in but it would not go. There is a small tab and I cannot tell if it goes up (towards the screen) or down. I think I can get it back in with a toothpick or similar but want it to stay (and not lose it) and for it to re-seal the door properly. Not being able to close the USB door is a BIG deal to me.
I had been meaning to get a docking charger but bought some from China and they were crap. Guess I'll have to break down and get a real DK30.
The o-ring goes on the door.
Tab to back by the looks
Glue it back? What kind of glue?
Sent from my C6833 using XDA Free mobile app
mknewman said:
Glue it back? What kind of glue?
Sent from my C6833 using XDA Free mobile app
Click to expand...
Click to collapse
Try crazy glue very very small amount and please let it dry fully before putting the cap back into the phone!!!
Jammol said:
Try crazy glue very very small amount and please let it dry fully before putting the cap back into the phone!!!
Click to expand...
Click to collapse
Thanks Jammol. I'll try to figure this out. When I place it in the position it appears to belong in (now that I look closely I can see the small tab indention on the cap) but the part is so small I cannot even handle it with my big fat fingers, and don't really have a magnification station and stability setup to do it.
Big question is for the people who have had the cap break off, is there a source for the whole cap? Is it possible to install without taking the whole phone apart? Would it make sense to just throw it away and forget it was there?
mknewman said:
Thanks Jammol. I'll try to figure this out. When I place it in the position it appears to belong in (now that I look closely I can see the small tab indention on the cap) but the part is so small I cannot even handle it with my big fat fingers, and don't really have a magnification station and stability setup to do it.
Big question is for the people who have had the cap break off, is there a source for the whole cap? Is it possible to install without taking the whole phone apart? Would it make sense to just throw it away and forget it was there?
Click to expand...
Click to collapse
I don't know what part of the world you are in but you can check these out. Couple folks have bought them:
http://www.ebay.de/itm/Original-Son...zer_Ersatzteile_Werkzeuge&hash=item2339fdd95e
I say just replaced the entire cap with one of those and call it good. Mine is experiencing the same thing, tearing off little by little. I think that is where water might be getting into my phone, but I'll be replacing the phone soon anyways. Just not sure what to get yet.
I have not gotten mine wet yet other than rain in my pocket but the lines are much better with the cap on than removed, and I'd worry about the edge material getting pulled off the rest of the phone. I appreciate the ebay refrence and will try to find a US version. So is there a way to remove the old cap without breaking it off internally and having the tab rattling around inside?
I ordered a couple of the caps and a magnetic charger off thEbay US, but seller was in Spain so it will be a while. Crappy design trying to get rubber to adhere to plastic.
Does anyone know how to safely remove the old one? Just yank? slip something very thin in to try to get the tab to ride over the notch?
Thanks,
Marc
Super glue is what bonds o-rings to other materials because of the greasy slippery surface. Mine has also come loose. Contact glue, industrial glue or anything else wont bite on that thing because of its chemical resistance that the o-ring has.
try to get a hold of a bottle of Loctite 401 meanwhile if you can't wait for the parts
http://www.ebay.com/itm/LOCTITE-401...Instant-Adhesive-Super-Glue-20g-/121407567300
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Apply with a pin or paper clip I take it?
SÜPERUSER said:
Super glue is what bonds o-rings to other materials because of the greasy slippery surface. Mine has also come loose. Contact glue, industrial glue or anything else wont bite on that thing because of its chemical resistance that the o-ring has.
try to get a hold of a bottle of Loctite 401 meanwhile if you can't wait for the parts
http://www.ebay.com/itm/LOCTITE-401...Instant-Adhesive-Super-Glue-20g-/121407567300
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Click to expand...
Click to collapse
mknewman said:
Apply with a pin or paper clip I take it?
Click to expand...
Click to collapse
mmm something like that I dunno really.. I've yet have to figure this out myself lol. Use your imagination! :laugh:
At my moms work when I was young they had superglue bottles from loctite with really tiny metal pipes attached on them I wonder what loctite model that is. They could be used to do any precision work!
So it's possible to get the new one in properly once I get the old one out? From this picture it appears the new tab should slide in but I'm worried if you have to tug hard to get the old one out.
SÜPERUSER said:
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Click to expand...
Click to collapse
calm down...just pull on it. You won't break anything
edit: its no big deal to get the new one in
Great! Thanks, that's a relief. I'll let ya'll know how it goes when I get it. May buy a few extras too.
I got the replacement parts from thEbay tonight. Pulled on the old one and it came right out. Took 2-3 tries to get new one in. Tether was bunching up. Turns out if you hold it at about 45 regress it goes right in.
Thanks for the help everyone.
Sent from my C6833 using XDA Free mobile app
gutted!
I am so gutted i didn't see this thread before I sent my phone to Sony for warranty repair.
My gasket didn't fall off, it started to come unstuck so was hanging off and when closing the lid the gasket would unroll and the lid would open.
I sent it to Sony as I think this is there fault. The gasket should stay attached for the duration of the warranty.
They want to charge me £55 for repair, handling and shipping!! I have had my claim escalated and now they say 'upon further inspection the device is bent'!! They are willing to send it back free of charge should I not want to have it repaired...... But should I now expect the device they send back to me to bent when I know full well it was in near perfect condition when I sent to them?!?!
The bottom line is follow instructions from this thread. DO NOT send your phone to Sony.
Sony use 'authorised repair centres' so they don't even know what is going on with your device and the trust you put in Sony to give your device to a respected engineer is misplaced.