[Q] Vpad 7 Recovery mode fails to show menu - Viewsonic ViewPad 7 & Variants

When I try to install a new ROM,
Installation:
1. Power down your device.
2. Power on device holding power button and both volume keys simultaneously.
3. Upon power up you will see the birds logo and 'enter recovery' text in the top left corner of the screen.
4. Use the volume keys to step through the menu, power to select and back.
At this point, the vol key don't do anything,
all I can do is a reset with a paper clip.
Vpad 7 sw ver= 3.16R, model= FM6-0001, hw ver= 1.06
Regards
Mike Pratt

Errrr, let's see, just to be sure - you had previously rooted this Vpad7 and installed ClockWorkMod Recovery 2.x or 3.x on it?
Do you have a Backup on the mSD card that you can restore from, although that's not likely the problem ....
I'm guessing that it's a hardware (power switch) issue so replacing it under warranty (if it's still covered) would be the best option ....
P.S. What ver. of Recovery are you using, just to be sure ?? I just upgraded mine from 3.0.2.8 to CWM 5.0.2.6 and there might be a "minor" issue(s), maybe on my end ....

Letitride said:
... I'm guessing that it's a hardware (power switch) issue so replacing it under warranty (if it's still covered) would be the best option ....
Click to expand...
Click to collapse
Yeah. I'm having the same issue. Just got off the online chat with "Mia", and she gave me the ok to send my unit in. It's been less than a year, so I'm in luck. I would do the same if I were him.

Related

[Q] confused about locked and hardware locked

Hi guys,
I am still new to this phone and I am trying to read as much as possible. but there is a lot of terminology to absorb. And I definitely want to make sure my phone is OK before the 14-day period when I can exchange it..
So, I unlocked my phone using one of the posted methods on here. i tried it with an AT&T sim card and it works.
Now, I read that there is something like a "hardware lock" which is bad .. because.. I wont be able to root or put rom or update my phone? I tried to go to a recovery mode, but could not, is my phone hardware locked?
Thanks in advance!
azsamsancho said:
Hi guys,
I am still new to this phone and I am trying to read as much as possible. but there is a lot of terminology to absorb. And I definitely want to make sure my phone is OK before the 14-day period when I can exchange it..
So, I unlocked my phone using one of the posted methods on here. i tried it with an AT&T sim card and it works.
Now, I read that there is something like a "hardware lock" which is bad .. because.. I wont be able to root or put rom or update my phone? I tried to go to a recovery mode, but could not, is my phone hardware locked?
Thanks in advance!
Click to expand...
Click to collapse
Did you do the correct way to recovery?
-Phone off, both volume keys held down
-Hit and hold power button while holding down volume keys
-The word vibrant will come on, and then it will go black again and reboot (still holding down all three buttons)
-When you see the word vibrant THE SECOND TIME let go of the power button but keep the volume keys down until you boot into recovery.
If not, most likely you are hardware locked. I don't have this problem but I think there's threads around for hardware locked users for workarounds and such.
yeah, i did exactly that:
1) power phone off
2) hold both volume buttons
3) hold power button
4) vibrant comes on, wait, vibrant comes on 2nd time
5) release power button, still holding both volume buttons
6) Vibrant starts in a normal way, i do not see anything different, so I assume i am in a regular mode, not recovery mode
azsamsancho said:
yeah, i did exactly that:
1) power phone off
2) hold both volume buttons
3) hold power button
4) vibrant comes on, wait, vibrant comes on 2nd time
5) release power button, still holding both volume buttons
6) Vibrant starts in a normal way, i do not see anything different, so I assume i am in a regular mode, not recovery mode
Click to expand...
Click to collapse
Make sure your Vibrant is hardware locked.
If you suspect that it is, you can read this thread HERE.
That will help you get your hardware locked phone working.
Unless you want to go get a new one.
I tied the following ways to test if my phone is hardware locked
1) vol up+ down + power
2) volu up + power
3) vol down + power
Nothing worked How would my phone would be hardware locked? I have not rooted, installed roms, nor apps.. Everything is stock, except that I unlocked the phone. that's all..
And it will be a huge pain to ship the phone back + wait for a new one, which there is no guarantee it wont be hardware locked ..?
Would I be able to install any rom if I am hardware locked? It seems like bionix mod is pretty popular..
Hardware lock is simply a boot loader issue. The phone has software the runs when you turn it out which in turn boots up the operating system. In hardware locked phones, the boot loader is not looking for the key combo to access recovery or download mode. If you go to the link provided, it tells you how to flash your phone to update the boot loader so that it is no longer hardware locked.

[Q] Screen flickers at boot

As soon as I boot I get random lines / flickering unable to read screen. I cannot tell if I get in the recovery screen. Based on the noises I can tell it boots up. Since I can't read the screen at all, the software side will have to be done on my win 7 machine. Is there anything I can do?
I don't know the Kernel number or android build, etc. As I bought this on ebay.
Probably your build. I bought mine off of eBay too, broken though, and repaired it.
The first cm10 Rom I installed had that problem where it'd look like a static t.v. channel upon booting sometimes or it would just randomly do so while on. Resetting would be the only way to return the screen back to normal. Now two builds later, I have yet to re-experience that issue.
So I'd say keep resetting with volume down and power to get into recovery and install a new rom. The previous owner probably had a bad flash and wasn't able to restore the screen condition.
If that still doesn't work, correct me if I'm wrong, I believe you can rescue your tab with a factory reset using ADB, as long as you get into download mode.. which should be the first option on the right when launching the tab into recovery.
If you're unfamiliar with ADB like me, I can give you the steps in number counts to get your device into recovery and hard reset it.. like: click volume up once and hit power, hit volume down 4 times then power etc.
-*Sent from my T-Mobile GS3*-
OTAw said:
I can give you the steps in number counts to get your device into recovery and hard reset it.. like: click volume up once and hit power, hit volume down 4 times then power etc.
Click to expand...
Click to collapse
Please do, that would help a lot!!!
fstfrd00 said:
Please do, that would help a lot!!!
Click to expand...
Click to collapse
This probably will depend on the recovery that you have installed on the tablet, whether it's stock or custom.
This method is for clockwork recovery (CWM):
To get into recovery:
-Hold volume down + power buttons and release the power button once the "Galaxy Tab 10.1" logo shows (should be the first screen to even show). Continue holding volume down for a few more seconds and you should then be at a screen where you choose from download mode or recovery.
-Volume down
-Volume up
Once in recovery:
-Volume up 2x
-Power
-Volume down 5x
-Power
Your device should now be factory restored so you can just hold the power button until it restarts. If that still doesn't fix the issue, I'll look up the stock recovery procedure and you can try that.
Remember, volume UP is the 3rd button on the top left corner of the device and volume down is the second.
-*Sent from my T-Mobile GS3*-
Perfect, thanks for the help!!!
fstfrd00 said:
Perfect, thanks for the help!!!
Click to expand...
Click to collapse
Glad I could help. I'm assuming from your reply that it worked?
-*Sent from my T-Mobile GS3*-
Hey guys i solve my problem today i desided to solve it anyway and now i am free from this **** ....
i just go to http://droidbasement.com/galaxy/roms/cm10/p4/ and download
bootloader.tar.md5
latest recovery.tar.md5
cm-10-20121112-EXPERIMENTAL-p4.zip
but before start anything first i format my tab memory then restart in download mode install bootloader.tar.md5 and recovery.tar.md5 ... volla ... reboot in recovery mode volla thats it all is now working perfect .... then i install cm-10-20121112-EXPERIMENTAL-p4.zip now my tab is free on madness ...
must try but first fully clean your tab ...
iff its really work then click on thanks button ...

Nexus 10 - unlock bootloader didn't go as expected

Hi guys,
I tried to unlock the bootloader of my Nexus 10 before rooting it. Unfortunately, it didn't work and I can't use it anymore (I either have the "Loading X" forever or a dead droid while trying to go to the recovery mode).
I'm used to do that kind of modifications (only on Samsung Galaxy S and S3 though) and I don't know what I did wrong (but I usually flashed with Odin).
Anyway, I used this tool (after enabling the usb debug and allowing unknown sources) : http://forum.xda-developers.com/showthread.php?t=2001868
I installed the drivers on my PC (menu 1 in the tool), then I could see my device in ADB MODE (in the tool menu). I tried to unlock the bootloader (3rd option in the menu) and it was written completed. My device reboots and nothing happens. I can access the fastboot mode (is it the download mode ?).
I have Odin.
Can someone help me to get a working device ?
Thank you very much.
hiveNzin0 said:
Hi guys,
I tried to unlock the bootloader of my Nexus 10 before rooting it. Unfortunately, it didn't work and I can't use it anymore (I either have the "Loading X" forever or a dead droid while trying to go to the recovery mode).
I'm used to do that kind of modifications (only on Samsung Galaxy S and S3 though) and I don't know what I did wrong (but I usually flashed with Odin).
Anyway, I used this tool (after enabling the usb debug and allowing unknown sources) : http://forum.xda-developers.com/showthread.php?t=2001868
I installed the drivers on my PC (menu 1 in the tool), then I could see my device in ADB MODE (in the tool menu). I tried to unlock the bootloader (3rd option in the menu) and it was written completed. My device reboots and nothing happens. I can access the fastboot mode (is it the download mode ?).
I have Odin.
Can someone help me to get a working device ?
Thank you very much.
Click to expand...
Click to collapse
Easy fix. Get to the dead droid recovery menu and then press all 3 buttons on the top. You will get into the blue recovery options. Choose factory reset.
Sometimes unlocking the bootloaders scrambles a few things on this device and it goes into boot loop. After the factory reset, you'll be fine. PM me if you still have issues.
Sent from my Galaxy Nexus using Tapatalk 2
Blueback22 said:
Easy fix. Get to the dead droid recovery menu and then press all 3 buttons on the top. You will get into the blue recovery options. Choose factory reset.
Sometimes unlocking the bootloaders scrambles a few things on this device and it goes into boot loop. After the factory reset, you'll be fine. PM me if you still have issues.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
Okay, thank you very much. I didn't know I had to press the 3 top buttons again after the dead droid screen, I thought it failed loading the Recovery Mode.
I have to setup my account etc again so I guess it is safe to say it worked.
Additionally, I tried this method after the recovery : http://forum.xda-developers.com/showthread.php?t=2015467
and it worked fine. My device has an unlocked bootloader and is rooted.
hey if someone could help me im stuck myself, after i had the dead android in recovery mode i tried to flash software with the toolkit in fastboot and now when i go to recovery its just a blank screen till i hold the bottom combo again and it takes me back to fastboot
Blueback22 said:
Easy fix. Get to the dead droid recovery menu and then press all 3 buttons on the top. You will get into the blue recovery options. Choose factory reset.
Sometimes unlocking the bootloaders scrambles a few things on this device and it goes into boot loop. After the factory reset, you'll be fine. PM me if you still have issues.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
Hey,
I'm having the same problem. I get to the dead droid instead of recovery and tried hitting all three buttons again but it's just looping again.
Any ideas?
maximepull said:
Hey,
I'm having the same problem. I get to the dead droid instead of recovery and tried hitting all three buttons again but it's just looping again.
Any ideas?
Click to expand...
Click to collapse
It sounds like you didn't actually perform a factory reset. The key combination to get into stock recovery from the dead android screen is Power + Vol-Up. That will bring up the option to factory reset.
So if your powered off or bootlooping, hold the Power + Vol-Up + Vol-Down until you're back in the Bootloader. Use Vol buttons to select Recovery Mode and tap Power. When the droid w/ the Red "!" appears, hold the Power button and quick press the Vol-Up button. This should take you into stock recovery. Select Factory reset. Reboot. After a few minutes, the device should boot normally.
Good luck.
sharksfan7 said:
It sounds like you didn't actually perform a factory reset. The key combination to get into stock recovery from the dead android screen is Power + Vol-Up. That will bring up the option to factory reset.
So if your powered off or bootlooping, hold the Power + Vol-Up + Vol-Down until you're back in the Bootloader. Use Vol buttons to select Recovery Mode and tap Power. When the droid w/ the Red "!" appears, hold the Power button and quick press the Vol-Up button. This should take you into stock recovery. Select Factory reset. Reboot. After a few minutes, the device should boot normally.
Good luck.
Click to expand...
Click to collapse
Ok found a video showing that when you get to that part where there's the dead droid (the red !), you don't press hold hold all three buttons but tap them until the recovery screen shows up.
So finally did that but I still have the same problem.
My initial problem was, I received my N10, open the box, turned it on and it started freezing and rebooting. Can't get past the wifi step.
Tried hard and many times to finally get to enter my gmail account, etc
Updated to 4.3, problem persisted so I figured, maybe the factory flashed a bad rom?
So I unlocked it, rooted it and tried flashing older stock versions, same problem.
Tried flashing CM, same; PA, same...
Tried deactivating location service as suggested elsewhere: same; uninstall chrome: same
Even CM withouf GAPPS wouldnt work
So basically, I have a $500 brick. Completely useless as it freezes every 30 seconds.
Decided not to return the device because although I am Canadian, I live in SE Asia and had a visiting friend bring it to me. Way past the return period and the overall experience would be a real pain in the butt... Don't know what to do. Really hoping Kit Kat will solve it but I have doubts.
What do you think?
Sorry. I don't know enough about these things to give more in depth troubleshooting advice. I just recently got my N10 & unlocked it and based on your original post, I thought that's where you needed help. But it sounds like you got past that and got it unlocked.
Have you tried downloading a factory image directly from Google and installing that? If it's locking up on a fresh install of any ROM, it very well may be a hardware issue. You may have to file a warranty claim if possible.
maximepull said:
Ok found a video showing that when you get to that part where there's the dead droid (the red !), you don't press hold hold all three buttons but tap them until the recovery screen shows up.
So finally did that but I still have the same problem.
My initial problem was, I received my N10, open the box, turned it on and it started freezing and rebooting. Can't get past the wifi step.
Tried hard and many times to finally get to enter my gmail account, etc
Updated to 4.3, problem persisted so I figured, maybe the factory flashed a bad rom?
So I unlocked it, rooted it and tried flashing older stock versions, same problem.
Tried flashing CM, same; PA, same...
Tried deactivating location service as suggested elsewhere: same; uninstall chrome: same
Even CM withouf GAPPS wouldnt work
So basically, I have a $500 brick. Completely useless as it freezes every 30 seconds.
Decided not to return the device because although I am Canadian, I live in SE Asia and had a visiting friend bring it to me. Way past the return period and the overall experience would be a real pain in the butt... Don't know what to do. Really hoping Kit Kat will solve it but I have doubts.
What do you think?
Click to expand...
Click to collapse
sharksfan7 said:
Have you tried downloading a factory image directly from Google and installing that?
Click to expand...
Click to collapse
^ that's your solution. If you dont know how to just pm me
Sent from my Galaxy Nexus using XDA Premium HD app

[Q] HELP-Big trouble: is it possible to enter recovery without vol-up button ??

Hello there,
I'm in a very situation:
- My volume-UP button does nor respond (i changed the button+camera part in the past but no way, it's a worth problem on the MB)
- It happens that I've made a bad update of my rom and it's not booting
- Then I can use power button + volume-down to enter menu and navigate in it but no way to enter recovery !!
Is there a tool or any trick to enter recovery in this situation ?
hope someone knows how to make a miracle
thanks
sambastrakan said:
Hello there,
I'm in a very situation:
- My volume-UP button does nor respond (i changed the button+camera part in the past but no way, it's a worth problem on the MB)
- It happens that I've made a bad update of my rom and it's not booting
- Then I can use power button + volume-down to enter menu and navigate in it but no way to enter recovery !!
Is there a tool or any trick to enter recovery in this situation ?
hope someone knows how to make a miracle
thanks
Click to expand...
Click to collapse
I just dealt with the vol up issue. For me the foam pad by the vol up had broken free. The only way to fix this is to replicate the foam pad width, and apply enough pressure to the side of the vol up and down part for button functionality. Its a delicate situation if you go the self repair method. The flex cable replacement method is a limited option due to the limited amount of flex cables (its called the optical enhancement flex cable or something like that). The only other option is a device replacement, followed by a motherboard swap so you keep your old system.
Sent from my MB860 using xda app-developers app
palmbeach05 said:
I just dealt with the vol up issue. For me the foam pad by the vol up had broken free. The only way to fix this is to replicate the foam pad width, and apply enough pressure to the side of the vol up and down part for button functionality. Its a delicate situation if you go the self repair method. The flex cable replacement method is a limited option due to the limited amount of flex cables (its called the optical enhancement flex cable or something like that). The only other option is a device replacement, followed by a motherboard swap so you keep your old system.
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
In my case it's not a foam pad / pressure problem. As I said I already replaced the button part (which comes with the camera (5 bucks in hong-kong)), and yes it wasn't easy to make the replacement. But the problem continued. The strange thing is that I was able to use the vol-up button after clicking a thousand times on vol-up&down. In that case the vol-up button was working fine for a few minutes only. But today even after clicking during half an hour, nothing. It looks like a capacitor problem on the motherboard.
I was hoping for a program able to force the phone to boot in recovery, even thinking it's not possible (we need to choose a menu option to let a program comunicates with the phone).
I think I'm fuc... this time. Moto no more for sure.
sambastrakan said:
I was hoping for a program able to force the phone to boot in recovery
Click to expand...
Click to collapse
Oh really?
Code:
adb reboot recovery
ravilov said:
Oh really?
Code:
adb reboot recovery
Click to expand...
Click to collapse
I'm stucked in the 1st level menu (where you choose fastboot, recovery, rsd and other stuff), there is no adb access neither fastboot command line at this level.
Oh I see. Sorry, no ideas then.
rom manager app in playstore has a reboot in recovery mode button
Sent from my MB860 using xda app-developers app
tweetycontrabajo said:
rom manager app in playstore has a reboot in recovery mode button
Click to expand...
Click to collapse
Obviously you can't read either, just like me.
i can read. the rom manager app does exactly that, forces to reboot in recovery mode, don't need to be choosing between fastboot or rsd or recovery.
Sent from my MB860 using xda app-developers app
tweetycontrabajo said:
i can read...
Click to expand...
Click to collapse
Clearly you can't. I suggest you reread everything again.
He's stuck in the bootloader, way before the ROM even thinks of loading. What good is an app then?
I'm back in my rom.
After clicking again like crazy on vol-up&down, vol-up button has responded for a few minutes, just 2 or 3 minutes, but it was sufficient to enter recovery via bootloader. ouff !
I'm not going to modify my rom anymore, too dangerous.
Someone knows an app able to modify the calling volume ? It's ok for now but one day I will click vol-down during a call and ... no way to vol-up ! hahaha, crapy motorola (which not allows international warranty) !
thanks
Your story serves as a warning to me.
Never modify the button with Motorola at the bootloader level, too risky. (android level like inside system\ is OK).
To summarize problem that thread-opener had:
- He's stuck at bootloader (screen says unlocked, fastboot, or RDS, recovery, etc...etc)
- can cycle through fastboot, rds, recovery with Vol-down.
- but cannot select (confirm selection) with Volume-up (button software reassigned, or button hardware contact broken, or etc..etc)
====>>> dead-end to way out ! No download mode.

[Q] I717 reboots every 2 minutes

Got the phone with rebooting problem: it got the rebooting after updated. The device restarted during Android app optimization stage so I just unblock with the AT&T stock file (pda-odin-att-stock.tar) after that the phone can boot up fine the problem still. It works but continuing reboot every 2 minutes. I tried to clear the cache, test redbend fota... but nothing works
Anyone has idea?
abbuyacc said:
Got the phone with rebooting problem: it got the rebooting after updated. The device restarted during Android app optimization stage so I just unblock with the AT&T stock file (pda-odin-att-stock.tar) after that the phone can boot up fine the problem still. It works but continuing reboot every 2 minutes. I tried to clear the cache, test redbend fota... but nothing works
Anyone has idea?
Click to expand...
Click to collapse
your English is a little rough my friend
did you get the phone with reboot issue?
or
it started rebooting after an update?
what kind of update?
what rom are you trying to run?
and I don't understand "unblock with the ATT stock file " ?????
also what is "test redbend fota" ???
you need to be a little clearer with information please
captemo said:
your English is a little rough my friend
did you get the phone with reboot issue?
or
it started rebooting after an update?
what kind of update?
what rom are you trying to run?
and I don't understand "unblock with the ATT stock file " ?????
also what is "test redbend fota" ???
you need to be a little clearer with information please
Click to expand...
Click to collapse
First of all sorry about my English. I wish I can do better.
I got the phone with the rebooting and base on the owner of the phone he said it started rebooting after an update.
Not sure what was of update to but the phone I got always rebooting during Android app optimization stage ( when it updating about 90 files or so) but it got reboot when updating to the file of 57th (So it was not actually working)
I watched and followed the youtube (how to unblock/unbrick galaxy i717) which it used the pda-odin-att-stock.tar file with the ODIN3 V1.85 (I guess that original ROM of AT&T (android version 2.3)
After successful unblock/unbrick the phone the phone actual worked but the problem still. It works but only 2 minutes and the phone reboots.
2/ test redbend fota is one the options you can choose after hard booting the phone using both up - down keys and power key (other options are to clear the cache, or wipe the data..)
That actually happened to me while testing out Bean Stalk(which btw AWESOME ROM). It would do a Random Reboot and continuously do that every 2 minutes or so. The way I fixed it was by doing the following steps:
1) Power off your phone. If unable to power off, remove and reinsert the battery.
2 )Press and hold between both Volume keys and the Power key at the same time until the phone vibrates, then release ONLY the Power key.
3)Continue holding the Volume keys until Samsung appears on the screen. Then release both volume keys.
The recovery menu will display.
4) Press Volume down to move to option 3, Wipe data/factory reset, and then press the Home key to accept.
5) Use Volume Up and Volume Down buttons to navigate in the menu and select Yes- Delete all user data.
6)Navigate to highlight OK and press the Home key to select.
7) Select Reboot system now.
PLEASE UNDERSTAND THAT THIS WILL DELETE EVERYTHING INSIDE YOUR SD CARD AS WELL! SO DO A BACKUP BEFORE ERASING EVERYTHING!
hafridi said:
That actually happened to me while testing out Bean Stalk(which btw AWESOME ROM). It would do a Random Reboot and continuously do that every 2 minutes or so. The way I fixed it was by doing the following steps:
1) Power off your phone. If unable to power off, remove and reinsert the battery.
2 )Press and hold between both Volume keys and the Power key at the same time until the phone vibrates, then release ONLY the Power key.
3)Continue holding the Volume keys until Samsung appears on the screen. Then release both volume keys.
The recovery menu will display.
4) Press Volume down to move to option 3, Wipe data/factory reset, and then press the Home key to accept.
5) Use Volume Up and Volume Down buttons to navigate in the menu and select Yes- Delete all user data.
6)Navigate to highlight OK and press the Home key to select.
7) Select Reboot system now.
PLEASE UNDERSTAND THAT THIS WILL DELETE EVERYTHING INSIDE YOUR SD CARD AS WELL! SO DO A BACKUP BEFORE ERASING EVERYTHING!
Click to expand...
Click to collapse
I have done it already and it didn't works. I tried to clear the cache also and other options too but none of them worked.
abbuyacc said:
I have done it already and it didn't works. I tried to clear the cache also and other options too but none of them worked.
Click to expand...
Click to collapse
Could it be a battery issue? I mean if its not software, it might be hardware. Please check if the battery is fine? If you could elaborate the steps you took or the update process you followed, that would be great.
Don't worry we will definitely figure this out, i know how sad it can be when you are without your phone.
hafridi said:
Could it be a battery issue? I mean if its not software, it might be hardware. Please check if the battery is fine? If you could elaborate the steps you took or the update process you followed, that would be great.
Don't worry we will definitely figure this out, i know how sad it can be when you are without your phone.
Click to expand...
Click to collapse
No. Surely it is not about the battery. Battery is full and hold the charge pretty well. As I mentioned I was re-installed the original ROM of the phone and there was nothing much to say about this procedure. After reinstalled the original rom the phone works but the problems is still same (rebooting after 2 minutes), before the the phone didn't work and just was in the updating stage but I guess the time of the updating file was also about 2 minutes.
I believe this is about the software than the hardware issue. I am thinking that I may want to install the newest ROM to see it will work or not but I am in the middle of some works right now and have no time for it. So I am just wait to see if there is anyone had similar issue and follow their instruction. Thank you you all.
I am sure you either have hardware issue or in most circumstances it is a user issue.
Is there any possibility you have not read everything or something you are not understanding?
Those of us responding do so because our methods are tried and true. Nobody else is having this issue.
I just ask is it possible?
Have you confidently tried all suggestions with no shortcuts? Even the smallest deviation can lead to the biggest problems
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Here is a suggestion:
Please go to stock rom. After Odin restarts the phone...do not touch. Let the phone sit there for a little bit. Then if it restarts u might need to format your internal sd card after formatting system, data, cache and then install rom.
I had to flash it
hafridi said:
That actually happened to me while testing out Bean Stalk(which btw AWESOME ROM). It would do a Random Reboot and continuously do that every 2 minutes or so. The way I fixed it was by doing the following steps:
1) Power off your phone. If unable to power off, remove and reinsert the battery.
2 )Press and hold between both Volume keys and the Power key at the same time until the phone vibrates, then release ONLY the Power key.
3)Continue holding the Volume keys until Samsung appears on the screen. Then release both volume keys.
The recovery menu will display.
4) Press Volume down to move to option 3, Wipe data/factory reset, and then press the Home key to accept.
5) Use Volume Up and Volume Down buttons to navigate in the menu and select Yes- Delete all user data.
6)Navigate to highlight OK and press the Home key to select.
7) Select Reboot system now.
PLEASE UNDERSTAND THAT THIS WILL DELETE EVERYTHING INSIDE YOUR SD CARD AS WELL! SO DO A BACKUP BEFORE ERASING EVERYTHING!
Click to expand...
Click to collapse
factory reset did not help me with this...I ended up having to flash CM 10.1. Its the most stable custom I have used on this phone yet....

Categories

Resources