hi
i have a htc touch plus or as they call it htc touch dual.digitizer issue it stoped responding so i bought new one fitted in and still the same problem .i think is a software problem i guess driver software for touch screen .if any one can help please
thanks
Touch Dual digitizer
Hi Saliml2
Not convinced it is a software issue. My digitizer on T-Mobile Touch Plus did the same thing. It stated behaving erratically and then stopped responding altogether. I replaced the digitizer (via eBay) and it work for a few days and then stopped again.
I have read around the internet and have tried several ROM updates etc (currently running a WM 6.5.5 found in other area of this forum) but this has not solved the problem.
It seem to be an alignment issue - i.e. screen alignment is outside the screen area, but there seems to be no way of getting it back. Could be a fault on the phone mainboard (?) but there doesn't seem to be any info around apart from sending it to HTC for repair (not viable as the phone value negates this)
My phone is still not working, I might try opening it up again and reseating the digitizer cable but have done this twice already.
Have you try change the flex cable?
I had one to, with the same problem, and after changing the flex everything was ok...
Good luck!
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
deepthought2471 said:
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
Click to expand...
Click to collapse
Maybe this is helpfull http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/
Goodluck
Flex cable, i was mean the cable between the mainboard and the lcd block, you can see it in the previous link, picture 20. Have you try it to change?
hello guys how did you manage to put the digitizer cable in place mine doesn t seem to get in place do i need something to hold the connector in place???
just fitted a new screen to my dell streak , when i turn it on i get the dell logo screen then a black screen and when that fades and i touch any button all i get is a screen full of multi coloured pixels help me i need my dell
message reply
i forgot to mention i email the guy in china i bought it from and this was his reply, i hope some one can make sense of it.
Tks very much for your mail and understand.
In this case,you need not the worry,this is normal,you can put it in the cable jack wipe clean with a pencil,and then install your screen.
Because of you know,they have a lot of black jack cable thing.you can try to do so.is thisi ok?
Locking Ribbon Cable Connectors
Don't know that this is the answer to your problem, but when I replaced my screen it would not respond to touch. I found that there are connector locks on the digitizer ribbon connector and on the side button ribbon connector. Once I flipped these locks down on the ribbon cables the screen responded to touch. It's something to check at least. Look at this discussion, http://forum.pocketables.net/showthread.php?t=9382&highlight=replacement , and you will get a good set of directions and some excellent large pictures to help you. Good luck!
I have G9 80 16GB Turbo. The plastic part of the inner micro USB feeder is broken and sticked out to the USB charger pin. My USB charger cable now blocked by that thing and cannot be use anymore. Now in the USB feeder of Archos just remain 4 tiny metals without plastic support (only 4 USB metal pins connector) and not able to take charge by anyway, it is bricked because of no battery power.
It is just 2 months old and no warranty since I bought it in airport transit. 3 times emailed [email protected] with no response as the world has suspected.
1. I've checked my Archos and did not find any screw other than single screw in the USB 3G compartment. I really thankful if anyone can write step-by step dismantle procedure.
2. Can anyone share the shape of USB type soldered to the PCB to enable me order the part and soldering it alone.
3. I've search this on thread : http://forum.xda-developers.com/showthread.php?t=1557506, but the information provided on how to dismantle is not very clear.
4. Thankyou in advance.
cangguek said:
I have G9 80 16GB Turbo. The plastic part of the inner micro USB feeder is broken and sticked out to the USB charger pin. My USB charger cable now blocked by that thing and cannot be use anymore. Now in the USB feeder of Archos just remain 4 tiny metals without plastic support (only 4 USB metal pins connector) and not able to take charge by anyway, it is bricked because of no battery power.
Click to expand...
Click to collapse
Uuups this is bad...
cangguek said:
It is just 2 months old and no warranty since I bought it in airport transit. 3 times emailed [email protected] with no response as the world has suspected.
Click to expand...
Click to collapse
It's sad that they did not reply, but do you think it is covered by warranty if your borked the USB connector?
cangguek said:
1. I've checked my Archos and did not find any screw other than single screw in the USB 3G compartment. I really thankful if anyone can write step-by step dismantle procedure.
Click to expand...
Click to collapse
There's only a single screw at the back.
The housing is hold together by some plastic clamps and it is a pain to open the case (at least compared to a A101IT Gen8).
You really need some force and be very careful not to damage anything...
I'll post a few pics this week in a different thread, because i opened the device last week and it was little bit catchy
cangguek said:
2. Can anyone share the shape of USB type soldered to the PCB to enable me order the part and soldering it alone.
Click to expand...
Click to collapse
Usually this is not an easy task... at least for the unexperienced ones.
Be careful with the thin lines on that PCB.
To unsolder the connector you'll need a lot of heat because it is connected to the gorund plane of the mainboard.
Anyway i don't know the manufacturer, but i guess these MicroUSB connectors are all pretty similar.
So try to catch one, wherever it is sold.
cangguek said:
3. I've search this on thread : http://forum.xda-developers.com/showthread.php?t=1557506, but the information provided on how to dismantle is not very clear.
Click to expand...
Click to collapse
You should start on the opposite side of the connectors and use some plectrums (used by guitar players) to lift off the plastic clamps.
As i said i'll prepare some pics...
EDIT: Here's an overview on how i opened the case.
As already stated it was a pain, and though i had been very careful, some tiny plastics got damaged.
The red circles mark the plastic clamps and the holes they were stucked in respectively.
The green arrows mark the direction i slided my guitar plectrum.
In between you'll have to use something like a screwdriver or putty knife to lift the clamps from their counterparts (this was the evil part).
In the end lift the top of the housing in the yellow direction.
Please take care of the flat cables of the TFT display, don't rip it off!!!
cangguek said:
4. Thankyou in advance.
Click to expand...
Click to collapse
You're welcome!
scholbert
scholbert,
I don't know how should I thanks for your detailed information and photo on your reply.
Below my comment:
1. There is no abuse on the USB port (even no single scratch or dent to prove the abuse, from new I feel it is really tight when I connect the cable into the port, finally the plastic part comes out "cleanly" along with the USB cable connector when I unplug. That's way I try to bet the warranty honor...ray.
2. I've checked eBay and I find many type of micro USB port selling.
3. Based on the generous help you've written I will try to dismantle my Archos when I have spare time within this week.
4. If I may ask, for what purpose you dismantle your Archos. And did you find any problem something like not properly tight when you remantle it again?.
5. From the picture, are all the clamps just on the display side, or mix up and down between the base and display?. Appreciate if you can post the zoom picture of the clamp and the hole to know it's anatomy to make easier when pushing during dismantle process. I also seeing 4 screw-like holes on 4 corner, are they also something like alignment clamps without actual screw?.
6. Big thankyou again for your response.
cangguek said:
4. If I may ask, for what purpose you dismantle your Archos. And did you find any problem something like not properly tight when you remantle it again?.
Click to expand...
Click to collapse
I don't know if i got a second edition device, but i realized this screen issue as well (pressure on the back causes effects on the display).
So i thought i may open it and try to solve this issue.
Anyway i always like to investigate on the construction of these devices...
cangguek said:
5. From the picture, are all the clamps just on the display side, or mix up and down between the base and display?. Appreciate if you can post the zoom picture of the clamp and the hole to know it's anatomy to make easier when pushing during dismantle process. I also seeing 4 screw-like holes on 4 corner, are they also something like alignment clamps without actual screw?.
Click to expand...
Click to collapse
To be exact, the clamps are located all on the base unit.
The display side got the holes for the clamps. I'll see if i could make a more detailed picture, to point you in the right direction.
Though i'm not sure if it helps.
The srew like holes you pointed at are for alignment only.
I also found some glue in the holes, but this is no problem.
Some words on seperation...
It worked out like this on the long side of the housing (upper and lower):
- I tried to seperate the display part and the base with the plectrum step by step
- tried to locate each clamp step by step
- then used a screwdriver
- tried to press gently against the clamp, direction outside to inside
(be very careful and the long side at the bottom, because of the display flex cable)
- then try to lift the parts more and more (it's terrible, but it works)
- keep an eye on the torsion of the display side
(seperate the parts too much, might crack the screen)
I guess i'll prepare some more pics...
Stay tuned!
scholbert
You are really a man god sent to me, thankyou so much. I'm really itching to do the job. First thing I will do once dismantle completed, is to wire two lines for temporary charging until the part I order arrive. If by any chance impossible to replace micro USB port, then I will make hole on the base for common round type DC charging port + and - only.
Hey cangguek,
as promised, here are some detailed views of the clamps (base unit) and holders (display side).
The are four holders in total with two holes each.
The holders are seperate parts and are mounted with three screws in the display part of the housing. Each holder fits into two clamps of the base unit.
Unfortunately they can only get disassembled after you managed to open the housing.
The edge of the clamps point to the border of the base unit housing.
So you may try to push them gently to the inside to release the mating part at the display side.
Anyway i hope things are clear enough now...
Some words on your idea of soldering a DC charging port:
Electrically this would work i guess, but there might be some driver issue which could prevent the unit from charging.
It depends on how the charger is identified by the software driver, which activates the charging process.
On some devices it is required to shorten the data lines of the usb connector, others use the id pin on the micro usb to detect wether a host pc or a wall charger is connected. I don't know how things are done on the Archos 80 G9.
I just wanted to point that out before you start soldering...
Good luck!!!
scholbert
scholbert said:
Some words on your idea of soldering a DC charging port:
Electrically this would work i guess, but there might be some driver issue which could prevent the unit from charging.
It depends on how the charger is identified by the software driver, which activates the charging process.
On some devices it is required to shorten the data lines of the usb connector, others use the id pin on the micro usb to detect wether a host pc or a wall charger is connected. I don't know how things are done on the Archos 80 G9.
I just wanted to point that out before you start soldering...
Click to expand...
Click to collapse
-Data lines are not shorted, charging cable is a fully functional usb cable
-There must be something done to 4th (unused) pin in micro sd plug so device can detect Archos/"normal" cables (my guess- check data lines->if usb host not present check 4th pin->original=fast charge/3rd party=slow charge)
gen_scheisskopf said:
-Data lines are not shorted, charging cable is a fully functional usb cable
Click to expand...
Click to collapse
Yeah i know that the data lines in the cable are not shorted.
AFAIK, they get shorted when connected to the wall charger.
I own a Milestone phone (which definitely requires the lines shorted for charging) and i successfully used the Archos wall charger to charge this device.
At least i wanted to point in this direction...
Thanks for your comment.
Regards,
scholbert
scholbert said:
Yeah i know that the data lines in the cable are not shorted.
AFAIK, they get shorted when connected to the wall charger.
I own a Milestone phone (which definitely requires the lines shorted for charging) and i successfully used the Archos wall charger to charge this device.
At least i wanted to point in this direction...
Thanks for your comment.
Regards,
scholbert
Click to expand...
Click to collapse
Ok
-data lines are shorted together in charger (not to gnd/vcc)
-that's strange but 4th pin seems not to be connected anywhere
sorry, left empty.
Dear scholbert,
All the process as you said really a devil. I am stuck here (at red arrow) and can not proceed unless I tear it with force. Seems there different clamps ?.
Now I am stopping the the job waiting your further help.
Thankyou for helping me:
cangguek said:
Dear scholbert,
All the process as you said really a devil. I am stuck here (at red arrow) and can not proceed unless I tear it with force. Seems there different clamps ?.
Now I am stopping the the job waiting your further help.
Click to expand...
Click to collapse
Yeah i know it hurts... but AFAIK all the clamps are identical.
Nevertheless i realized the same during disassembly.
Some of the clamps did release quite well, at some point i also was afraid i'll break the device into pieces. I'm sorry but i guess you'll have to use gentle force to get it seperated.
BTW, i don't want to be responsible if you damage something
Another warning at this point:
I even did break some small plastics during opening (in the mainboard area), but it doesn't matter in the end, because there are many clamps to hold the parts in place
Good luck!
scholbert
Just to confirm the only screw I removed only the one under the stand stick, I hope I am not missing here. I am still not continuing dismantle process, but at least 40% of the casing has been opened.
cangguek said:
Just to confirm the only screw I removed only the one under the stand stick, I hope I am not missing here.
Click to expand...
Click to collapse
Right, only one screw...
Regards,
scholbert
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
cangguek said:
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
Click to expand...
Click to collapse
someone needs to get out the old dustbuster
cangguek said:
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
View attachment 1057101 View attachment 1057102View attachment 1057103
Click to expand...
Click to collapse
I am happy to see these pictures as they confirm my suspicion. The usb charge port is only soldered on, no screws to hold it in place. That is not a proper mechanical construction and it is no winder it becomes disconnected with only a little use. I have sent 2 units back already which will no longer charge as the mount point has come loose. Number 3 broke too now and as they want me to pay for shipment again ( €50) I am thinking of fixing it myself in stead, but properly..
I have the same problem
Did you eventually repair this problem. If so were did you get the spare part. i have got the same problem. I think i might try returning to my supplier first.
Brilliant tips
scholbert said:
Uuups this is bad...
It's sad that they did not reply, but do you think it is covered by warranty if your borked the USB connector?
There's only a single screw at the back.
The housing is hold together by some plastic clamps and it is a pain to open the case (at least compared to a A101IT Gen8).
You really need some force and be very careful not to damage anything...
I'll post a few pics this week in a different thread, because i opened the device last week and it was little bit catchy
Usually this is not an easy task... at least for the unexperienced ones.
Be careful with the thin lines on that PCB.
To unsolder the connector you'll need a lot of heat because it is connected to the gorund plane of the mainboard.
Anyway i don't know the manufacturer, but i guess these MicroUSB connectors are all pretty similar.
So try to catch one, wherever it is sold.
You should start on the opposite side of the connectors and use some plectrums (used by guitar players) to lift off the plastic clamps.
As i said i'll prepare some pics...
EDIT: Here's an overview on how i opened the case.
As already stated it was a pain, and though i had been very careful, some tiny plastics got damaged.
The red circles mark the plastic clamps and the holes they were stucked in respectively.
The green arrows mark the direction i slided my guitar plectrum.
In between you'll have to use something like a screwdriver or putty knife to lift the clamps from their counterparts (this was the evil part).
In the end lift the top of the housing in the yellow direction.
Please take care of the flat cables of the TFT display, don't rip it off!!!
You're welcome!
scholbert
Click to expand...
Click to collapse
Great tips & will add my own step by step as replacing my screen on G9 after it parachuted from 2 foot onto a rubber floor!!:good:
topsterdog said:
Great tips & will add my own step by step as replacing my screen on G9 after it parachuted from 2 foot onto a rubber floor!!:good:
Click to expand...
Click to collapse
I'd be very interested in this and to learn where you bought the replacement screen...
I have an 80G9 with cracked screen and LCD and busted digitiser.
Sent from my ARCHOS 101G9
Hi all,
Recently, I bought a Sony Xperia Tablet Z of which the previous owner had removed the whole screen. Tablet was working, then he dropped it, causing the screen to be broken (LCD was blacked out, tablet and digitizer/touch still working). He removed the screen assembly as a whole, had the intention to replace it but he just sold the rest of the tablet.
So I obtained an LCD/digitizer assembly form AliExpress, but after installing the screen and switching on the tablet, I got the same problem: Touch is working fine, tablet switches on nicely, I get some kind of 'blind-modus?' that responds to touch with sounds, it tells me I'm swapping through menus, but the LCD itself does not give any signal. Linking it to PC works fine too. Linking it to a TV requires an MHL cable, which I don't have...
My question is:
Does anyone know if this is a well-known problem after dropping an Xperia Tablet? I'm more or less sure it's not the LCD of the replacement screen that causes the problem (given the background), so the problem might be in the LCD flex cable, or worse, the logic board. But how to find the faulty component?
For the flex cable: I've tried to measure (multimeter) the resistance of the wires between each tiny pin of both the connectors of the ribbon, but it's not easy. Some pins on one connector are linked to multiple other pins of the other. Is there an easier way to check this, anyone any experience with this?
If it's the logic board, is there any way to make sure which component is broken, and is this fixable?
If it might help: I have a set of pictures of the logic board / flex / LCD.
Otherwise, I might just try and stop by a tablet/phone fix shop, ask kindly if I could quickly check one of their screens/cables to verify which parts are working/broken.
Thanks in advance!! Kind regards
Edit: I just noticed there is a specific forum for Xperia Z (one), this thread belongs there, sorry! Could this thread be moved there?