Can someone post all available frequencies(the voltage for lower than 600MHz and how much battery will it take comparing to the lower frequencies, eg 864 takes "x" battery more than 844)
Is there safe to use 864, and does it take to much battery, or not?
Thanks a lot
Sent from my LG-P500 using XDA App
frequencies below 600: 122, 245, 320, 480 (all of these use the same voltage)
frequencies above 600: 652, 672, 691, 710, 729, 748, 768, 787, 806 (the difference in battery varies depending on your governor and usage but generally, the higher the frequency the more battery it eats)
stability-wise, the only thing that can go wrong when you oc to 864 is a kernel panic. other than that it should be safe to use. however, in the long run i think it can harm your cpu (and yes it does use a lot of battery)
this is my understanding. if someone does not agree, feel free to point out what you believe is wrong
yep sweetnsour is right ...
All that can be added to what sweetnsour said is that there are three more frequencies over 600: 825, 844 and 864 MHz. But the chances for our CPU to be stable at any frequency above 806 MHz are very low.
Another notable side-effect to the overclock, beside quick battery depleting, is CPU overheating. I found my CPU to be stable at 806, but I went back to 729 just because the phone warmed up so much faster. At 729, I sense no difference compared to 600 MHz.
masteryx said:
All that can be added to what sweetnsour said is that there are three more frequencies over 600: 825, 844 and 864 MHz. But the chances for our CPU to be stable at any frequency above 806 MHz are very low.
Another notable side-effect to the overclock, beside quick battery depleting, is CPU overheating. I found my CPU to be stable at 806, but I went back to 729 just because the phone warmed up so much faster. At 729, I sense no difference compared to 600 MHz.
Click to expand...
Click to collapse
Yes a rooted with other tuning needs no oc, but what is thr highest that will not harm anything on a long term...
And does 122-480MHz really have same voltage?
Sent from my LG-P500 using XDA App
vlt96 said:
Yes a rooted with other tuning needs no oc, but what is thr highest that will not harm anything on a long term...
Click to expand...
Click to collapse
This is highly subjective, no one can tell for sure, except maybe the manufacturer. Buy in theory you should be safe with any frequency at which your CPU is stable and does not overheat. You will sell or trash the phone long before the overclock will affect anything.
And remember: the CPU spends a fairly low amount of time at the high frequency; most of the time it will fall back to the minimum, as long as there are no tasks requiring high processing power.
As far as I could gather in the 10 months I spent on this forum, the community agreed that 729 MHz is the most convenient value.
masteryx said:
This is highly subjective, no one can tell for sure, except maybe the manufacturer. Buy in theory you should be safe with any frequency at which your CPU is stable and does not overheat. You will sell or trash the phone long before the overclock will affect anything.
And remember: the CPU spends a fairly low amount of time at the high frequency; most of the time it will fall back to the minimum, as long as there are no tasks requiring high processing power.
As far as I could gather in the 10 months I spent on this forum, the community agreed that 729 MHz is the most convenient value.
Click to expand...
Click to collapse
Yes, 728hz is the best value for performance and battery.
Sent from my LG-P500 using XDA App
MaKTaiL said:
Yes, 728hz is the best value for performance and battery.
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
This flocking app needs thanks button...
Sent from my LG-P500 using XDA App
So the perfect is 480--729 SmartassV2 thanks...
Btw is the voltage really the same from 122 to 480?
Sent from my LG-P500 using XDA App
vlt96 said:
So the perfect is 480--729 SmartassV2 thanks...
Btw is the voltage really the same from 122 to 480?
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
I personally dont use Smartassv2 as it has some wakelock problems, so try different governors and find out which works best for you.
Btw, you are using the wrong kernel for your rom(6.5.8), you should be using fserve kernel or 4 Sept kernel by Franco (.32).
Yaa 480--729 is the perfect.Above 768 phone becomes unstable.
Altamash sayyed said:
Yaa 480--729 is the perfect.Above 768 phone becomes unstable.
Click to expand...
Click to collapse
And below 480 is same ****? I mean it won't do anything good to battery right?
Sent from my LG-P500 using XDA App
vlt96 said:
And below 480 is same ****? I mean it won't do anything good to battery right?
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
Exactly!
Sent from my LG-P500 using XDA App
MaKTaiL said:
Exactly!
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
Oh ye I got it *cool*
Sent from my LG-P500 using XDA App
Hey my is..
806/600 scary
But before 2 months i cant even overclock 768...how now 806??
Sent from my LG-P500 using xda premium
becuase governor is scary
Ohh...wen i removed my charger after 10 sec it gaved panic..ithink 768/480 is proper for me...nd can u give me details about the governer plz
Sent from my LG-P500 using xda premium
all using Smartass governer??
vj_dustin said:
all using Smartass governer??
Click to expand...
Click to collapse
Smartassv2 cuz v1 its like a petformance governor, only at max cpu... v2 goes down when screen off...
Sent from my LG-P500 using XDA App
vlt96 said:
Smartassv2 cuz v1 its like a petformance governor, only at max cpu... v2 goes down when screen off...
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
No true, smartass also caps when screen off
Related
Would this cause CPU freezing/crashing
I tried undervolting even minimally and my phone crashes, regardless of the values
I'm perfectly willing to accept that I may have one of those unlucky devices that just can't handle it, however I just realized I've been mixing the too apps....could this potentially be causing CPU confusion, ultimately leading to crashes?
Sent from my pocket rocket!
I doubt it I use both of tgem and nithing crashed maybe you phone cant handle overclock or ur settings try lowering them
TopShelf10 said:
Would this cause CPU freezing/crashing
I tried undervolting even minimally and my phone crashes, regardless of the values
I'm perfectly willing to accept that I may have one of those unlucky devices that just can't handle it, however I just realized I've been mixing the too apps....could this potentially be causing CPU confusion, ultimately leading to crashes?
Sent from my pocket rocket!
Click to expand...
Click to collapse
Sent from my SGH-T959 using XDA Premium App
T.C.P said:
I doubt it I use both of tgem and nithing crashed maybe you phone cant handle overclock or ur settings try lowering them
Sent from my SGH-T959 using XDA Premium App
Click to expand...
Click to collapse
No problem OCing, my phone loves being overcocked...oh, I mean clocked
Only problem is with UVing
Sent from my pocket rocket!
Then probably undervolting too much... What settings u using?
Sent from my SGH-T959 using XDA Premium App
T.C.P said:
Then probably undervolting too much... What settings u using?
Sent from my SGH-T959 using XDA Premium App
Click to expand...
Click to collapse
ive tried as low as -25 across the board....it usually rides well for a while....but eventually leads to crashes
TopShelf10 said:
ive tried as low as -25 across the board....it usually rides well for a while....but eventually leads to crashes
Click to expand...
Click to collapse
i would only recommend using 1 or the other.. (voltage app is best)
and -25ma across the board what do you mean?
1200
1120
1000
800
400
200
100?
your -25 on all of them?
cause if you read the threads supporting voltage app you will see to only change 5-7 profiles meaning...... dont do all of them... i keep only 4 of them under stock voltage.... as listed below (some phones cant handle the actual under volting NOT the over clocking.... and some cant do either)
1200: -25mv
1120: -25mv
1000: -25mv
800: -25mv
400: stock mv
200: stock mv
100: stock mv
i have been over clocking sense we got the kernels to do so... (i9000 kernels)
so if you need anymore help just pm me and i can help with a really good oc/uv set up or in your case just use setCPU its alot easier!
voltage app
which is the best governor for voltage app?
I had the same problem using both and thought it was my phone not liking oc with no uv but then I figured out by removing setcpu and only using voltage app that my phone was stable up to 1400. I have read many threads that state not to uv all freq's and not to use more than 5 states in the drawer. Also try to create the least voltage steps as possible and not to touch 800 cause thats where the phone us set to go to sleep and wake at which is critical. I think that set cpu and voltage asp conflict each other with scheduling, but I am not a dev so could not be sure.
Sent from my GT-I9000 using XDA App
I have used both. Set CPU sleep profile works beautifully paired with voltage control app.
Who prefers LiveOC over the regular OC system?
Just wondering.
Sent from my SCH-I500 using XDA App
I prefer to use voltage control and overclock the ol' fashioned way lol...I have played with nstools and live oc, but its more than I really need.
110%, 1320 mhz, stock voltages
Sent from my SCH-I500 using xda premium
neh4pres said:
110%, 1320 mhz, stock voltages
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
Which governor do you use? GlitchOndemand
Glitchass v2
Conservative
Interactive
Powersave
Performance
Lazy
Smoothass
Sent from my SCH-I500 using XDA App
i use glitchondemand/ fiops overclocked @ 1500mhz with no undervolt.
Enyo. said:
Which governor do you use? GlitchOndemand
Glitchass v2
Conservative
Interactive
Powersave
Performance
Lazy
Smoothass
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
Stock..
Sent from my SCH-I500 using xda premium
droidstyle said:
i use glitchondemand/ fiops overclocked @ 1500mhz with no undervolt.
Click to expand...
Click to collapse
No heat?
Is this dangerous? With no overheat, is this dangerous? Are you using this day to day?
Didn't get into oc too much.
neh4pres said:
Stock..
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
thanks so much
Sent from my SCH-I500 using XDA App
Enyo. said:
No heat?
Is this dangerous? With no overheat, is this dangerous?
I've never overclocked this high before. Didn't get into oc too much.
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
So.. You never tested 1.9 ghz before you released your kang kernel?
Sent from my SCH-I500 using xda premium
neh4pres said:
So.. You never tested 1.9 ghz before you released your kang kernel?
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
I tested it.
For a day or two.
But using my phone day to day.
Sent from my SCH-I500 using XDA App
enyo... I have tested with glitch kernel at 1.7 ghz and i currently hold the record benchmark for this device on antutu using performance governor. After testing for a half hour at that speed i fell asleep with the phone stuck at that speed. I'm typing this message with that phone now. That was done with glitch v13. The most i ever got from high clock speeds was freezes and reboots.
However, if you get stupid with live oc the story can be very different.
But to give an idea of what my phone handled back then, go to the cm7 glitch thread and check what the gpu/buss speed was at 1.7ghz. But remember that those bus/cpu speeds, and voltages were finely tuned by tk , and you probably won't be able to push that hard with live oc.
Sent from my SCH-I500 using xda premium
neh4pres said:
enyo... I have tested with glitch kernel at 1.7 ghz and i currently hold the record benchmark for this device on antutu using performance governor. After testing for a half hour at that speed i fell asleep with the phone stuck at that speed. I'm typing this message with that phone now. That was done with glitch v13. The most i ever got from high clock speeds was freezes and reboots.
However, if you get stupid with live oc the story can be very different.
But to give an idea of what my phone handled back then, go to the cm7 glitch thread and check what the gpu/buss speed was at 1.7ghz. But remember that those bus/cpu speeds, and voltages were finely tuned by tk , and you probably won't be able to push that hard with live oc.
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
So just overclocking, @ 1.5GHz or 1.2GHz and, monitoring the temp, processor will last just as long as it would non overclocked?
Sent from my SCH-I500 using XDA App
Enyo. said:
So just overclocking, @ 1.5GHz or 1.2GHz and, monitoring the temp, processor will last just as long as it would non overclocked?
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
It's all luck. Chance. Fate. If tk has not burned his phone yet i would say you have a lot of catching up to do to get the mileage he has. I had mine overclocked 1.5ghz for a few months.. And guess what, i have never monitored temp. But hey, i pay an extra couple dollars a month on top of insurance for lifetime warrantee. So i think my phone burning up would fall under that. But anyway, your stressing out to much over it.
Sent from my SCH-I500 using xda premium
neh4pres said:
It's all luck. Chance. Fate. If tk has not burned his phone yet i would say you have a lot of catching up to do to get the mileage he has. I had mine overclocked 1.5ghz for a few months.. And guess what, i have never monitored temp. But hey, i pay an extra couple dollars a month on top of insurance for lifetime warrantee. So i think my phone burning up would fall under that. But anyway, your stressing out to much over it.
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
Thanks so much.
Going to over clock to 1.5, not going to stress about it. Ulcers come like that
Sent from my SCH-I500 using XDA App
no heat and i use it daily...first time i can ever say this when overclocking to 1500. i agree with neh4pres posts...becareful with live oc it can screw your device up quick. most folks will never see any benifit by using live oc imo anyway. part of the reason why i just use vc...
I actually use 10% live oc and 1200mhz step... All voltages stock. Fully stable and it FLIES
Sent from my SCH-I500 using xda premium
I must have every bit of speed. That said here's the setup:
ICS AKOP 25 Glitch 14 B5 for 6.0
1200 step with 118 LOC
Glitch OnDemand with some OV and UV. (see pics)
Live OC is the way to go as you get a boost to your GPU and RAM in addition to the usual CPU bump.
thisguy23 said:
I must have every bit of speed. That said here's the setup:
ICS AKOP 25 Glitch 14 B5 for 6.0
1200 step with 118 LOC
Glitch OnDemand with some OV and UV. (see pics)
Click to expand...
Click to collapse
thx a bunch for this nfo. just used ur voltage settings for my device and was able to overclock into the 1300mhz range from the 1200 step. im impressed since last time it was very unstable at 1200 for me.
thx.
swagooo said:
thx a bunch for this nfo. just used ur voltage settings for my device and was able to overclock into the 1300mhz range from the 1200 step. im impressed since last time it was very unstable at 1200 for me.
thx.
Click to expand...
Click to collapse
with the devil kernel i have been running 102% loc between 200-1000mhz. on glitch i can oc up to 1500mhz with no loc, soon as i add any loc the device freezes. im guessing my leakage is not dialed in correctly for glitch, also i get a bit nervous playing wit arm voltages.
droidstyle said:
with the devil kernel i have been running 102% loc between 200-1000mhz. on glitch i can oc up to 1500mhz with no loc, soon as i add any loc the device freezes. im guessing my leakage is not dialed in correctly for glitch, also i get a bit nervous playing wit arm voltages.
Click to expand...
Click to collapse
Try these i have not had a reboot in over a week
Sent from my SCH-I500 using xda premium
What's the stock minimum frequency for the Xperia S? 384?
Is 192 too low and cause problems?
Thanks
192 is the minimum but 384 is the default value.
Yes it will cause freeze and reboot for some phones.
Sent from my LT26i using Tapatalk 2
I'll leave it at 384 then
Not really low! X8 minimum cpu frequency is 19mhz! Not kidding
Sent from my LT26i using xda premium
monivan said:
Not really low! X8 minimum cpu frequency is 19mhz! Not kidding
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
He's talking about xps and the minimum is 192 for now
Sent from my LT26i using Tapatalk 2
I've been with 192 for a while and the battery last a little longer. No problems
waiflih said:
I've been with 192 for a while and the battery last a little longer. No problems
Click to expand...
Click to collapse
Yes but the problem that not all the phones can run it,some may have freezing and reboots,same as overclocking.
Sent from my LT26i using Tapatalk 2
I use 192 with governor ondemand in setcpu.
Phone seems to be pretty fine to me.
I set it to 192 conservative when screen is off.
Too low, and you get lag and random reboots.
I think set cpu frequency as low as possible. It won't freeze ur phone unless u set powersave govenor as it keep the phone running at minimum frequency, and that would cause some troubles. Other govenors are smart! No need to worry as long as it need more frequency it wouldn't drop to minimum! But it will when it's in idle state. I even did undervolt to 750mv which should be 800mv! Still run fine!
Sent from my LT26i using xda premium
monivan said:
I think set cpu frequency as low as possible. It won't freeze ur phone unless u set powersave govenor as it keep the phone running at minimum frequency, and that would cause some troubles. Other govenors are smart! No need to worry as long as it need more frequency it wouldn't drop to minimum! But it will when it's in idle state. I even did undervolt to 750mv which should be 800mv! Still run fine!
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Any way (module or something) we can undervolt with stock kernel rooted?
In Xperia X8 that was possible before the bootloader was unlockable
I don't think we have it now. Until dev decided to do it! We've got kernels source from sony, it's not a big deal. The question is that who will do it!
Sent from my LT26i using xda premium
gm007 said:
192 is the minimum but 384 is the default value.
Yes it will cause freeze and reboot for some phones.
Sent from my LT26i using Tapatalk 2
Click to expand...
Click to collapse
I set mine to 192 and never had any problems. My suggestion is try it first.
Sent from my LT26i using xda premium
Well what are you over clock preferred settings. Mine are min: 1.024 and Max: 1.92 governor: smartassV2 I/O scheduler: deadline.
Sent from my Liquud ICS HTC Thunderbolt on Tapatalk 2
I run 1.22 Max and 245 min. Its bad for the CPU to be clocked the way you are.
Sent from my Thunderbolt using Tapatalk 2
Max 1.4 gHz - Min 250 mHz
jonah1234 said:
Well what are you over clock preferred settings. Mine are min: 1.024 and Max: 1.92 governor: smartassV2 I/O scheduler: deadline.
Click to expand...
Click to collapse
What's your battery life like? And as stated above, that can't be good for the processor.
Excessive heat is the worst thing you can do to a processor.
Sent from my Thunderbolt using Tapatalk 2
ArmyAg08 said:
Max 1.4 gHz - Min 250 mHz
What's your battery life like? And as stated above, that can't be good for the processor.
Click to expand...
Click to collapse
Its been pretty bad I guess that's why I just changed to Max 1.408 and min: 368
Sent from my Liquud ICS HTC Thunderbolt on Tapatalk 2
jonah1234 said:
Its been pretty bad I guess that's why I just changed to Max 1.408 and min: 368
Sent from my Liquud ICS HTC Thunderbolt on Tapatalk 2
Click to expand...
Click to collapse
Oc really isn't even necessary on liquid ics. You'll never notice the difference if you out it back down to stock.
Sent from my Thunderbolt using Tapatalk 2
disconnecktie said:
Oc really isn't even necessary on liquid ics. You'll never notice the difference if you out it back down to stock.
Sent from my Thunderbolt using Tapatalk 2
Click to expand...
Click to collapse
How is he overclocking on a ics rom anyways since we dont have kernel source I didnt think we could overclock ics roms yet.
I overclock to 1.2 ghz max and minimum either 245 or 368 mhz.
My battery life is pretty good, I'm running AOKP
droidjunkie said:
How is he overclocking on a ics rom anyways since we dont have kernel source I didnt think we could overclock ics roms yet.
Click to expand...
Click to collapse
The kernel is a modified gb kernel. It has oc capabilities.
Sent from my Thunderbolt using Tapatalk 2
disconnecktie said:
Excessive heat is the worst thing you can do to a processor.
Sent from my Thunderbolt using Tapatalk 2
Click to expand...
Click to collapse
I've heard that's actually second to voltage.
Duely blundered from my thunderdolt.
Dannar said:
I've heard that's actually second to voltage.
Duely blundered from my thunderdolt.
Click to expand...
Click to collapse
Yea I could see voltage being a major issue for a processor. If the voltage is to high it would heat the processor up though. Soooooo..... you're right back to heat being a huge factor.
Sent from my Thunderbolt using Tapatalk 2
What speeds and settings could I safely use to conserve battery?
I'm new to clocking.
I just want long lasting battery life.
Sent from my ADR6400L using xda premium
Leave the speeds stock and undervolt. When undervolting don't ever check save for boot or whatever until you are certain those settings won't cause you problems. If you undervolt to low it will reboot your phone. Go to high and it could overheat but I doubt you will need to do that for any reason. I would start with a -50 uv and see if it is stable for a few hours. If you think its good -25 to all for a few more. I usually can't get below -75 across all voltages but every phone is different so some people can go -100.
Sent from my ADR6400L using Tapatalk 2
disconnecktie said:
Leave the speeds stock and undervolt. When undervolting don't ever check save for boot or whatever until you are certain those settings won't cause you problems. If you undervolt to low it will reboot your phone. Go to high and it could overheat but I doubt you will need to do that for any reason. I would start with a -50 uv and see if it is stable for a few hours. If you think its good -25 to all for a few more. I usually can't get below -75 across all voltages but every phone is different so some people can go -100.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
Can I do this with setcpu?
Or would you recommend a different app?
Because when I started setcpu, it set me on 1036MHz max and 245MHz min. and the governor is set on lagfree, and then the scheduler is set on deadline.
Not really sure what to do here... lol.
Forgive me... like I said, I'm new to clocking.
I haven't touched anything since I started the app.. I was too concerned to.
It's not set on boot yet.
There's also a page for profiles and another for the governor... both of which are have me looking at them as if I were one of the three stooges looking at a supercomputer.
I have no idea what to do.
Sent from my ADR6400L using xda premium
Use incredicontrol. It's easier to use and profiles don't help much anyway. I would setup as 1024 max 245 min smartassv2 governor deadline scheduler -50 - -75 undervolt across the board.
Sent from my ADR6400L using Tapatalk 2
disconnecktie said:
Use incredicontrol. It's easier to use and profiles don't help much anyway. I would setup as 1024 max 245 min smartassv2 governor deadline scheduler -50 - -75 undervolt across the board.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
It's not giving me a 1024 max.
It jumps from 960000MHz to 1036800 MHz max. and then the min. is set to 245760MHz.
Next tab (SVS) has 850 in the box on the right all the way from 24576MHz to 245760MHz. Has 875 in the box beside 368640MHz, then 900 beside 768000MHz and so on.
Are you saying that in those small boxes on the right beside the xxx MHz I should lower that number by 50 all the way down to what I set the max to be?
Say from where it says 850 all the way from 24576MHz to 245760MHz, I should change that 850 to 800? And just -50 from every one all the way up the the MHz that I set as the max?
Wow, I hope I didn't just confuse you.
Sent from my ADR6400L using xda premium
What kernel are you using? The CPU and voltage table will vary with kernels.
Sent from my ADR6400L using Tapatalk 2
I'm running Gingeritis 3D v1.2 and running ziggy's kernel that comes with it.
Sent from my ADR6400L using xda premium
I am over locked to 1400 Max and 245min. Gives me nice battery life and great speed. ESP with the new Liquid ICS v.1.5 MR3
Sent from my ThunderBolt using xda app-developers app
Running Jester's AOSP ICS MR3 ROM, with SetCPU allowing from 245-1408. I have a custom profile for screen off to allow only up to 768 as well.
I'm just curious to see everyone's experience with the Faux kernel as opposed to the one that comes pre-installed.
Sent from my HTC_Amaze_4G using xda app-developers app
Capgun_Homicide said:
I'm just curious to see everyone's experience with the Faux kernel as opposed to the one that comes pre-installed.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
You have to read xda rules again.. Your free to use both of them and see it for your self without asking which is best in public!!
Sent from my HTC_Amaze_4G using xda premium
Capgun_Homicide said:
I'm just curious to see everyone's experience with the Faux kernel as opposed to the one that comes pre-installed.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
I think they're both great you can't go wrong with either kernel. It's like choosing a lamborgini or ferrari, they're both awesome but it truly comes down to preference.
I think I got better battery with faux 31 but I under clocked and undervolted so I can't do a fair battery life test.
Sent from my HTC_Amaze_4G using Tapatalk 2
SuperAfnan said:
I think they're both great you can't go wrong with either kernel. It's like choosing a lamborgini or ferrari, they're both awesome but it truly comes down to preference.
I think I got better battery with faux 31 but I under clocked and undervolted so I can't do a fair battery life test.
Sent from my HTC_Amaze_4G using Tapatalk 2
Click to expand...
Click to collapse
I've noticed better battery life as well; not majorly, but noticeably. Although I feel it also has a little perfomance drop. Could just be me, though.
Sent from my HTC_Amaze_4G using xda app-developers app
Sorry for a question within a question, but what does undervolting/overvolting do? I've only ever tampered with MHz frequencies.
Sent from my HTC_Amaze_4G using xda app-developers app
Capgun_Homicide said:
Sorry for a question within a question, but what does undervolting/overvolting do? I've only ever tampered with MHz frequencies.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
Don't worry.
Undervolting is basically adjusting the voltages so the cpu uses less voltage aka electricity. It helps a little but it can make your phone unstable so watch out. Of you undervolt use the system tuner app on the market. You should definitely under clock if you want to save power too. When you undervolt be sure to underclock, and don't do it too low or your phone might freeze! That's why your shouldn't go so extreme on it.
Overvolting is basically adding more voltage to the cpu. There is no point in doing it for our amazes to be honest. It is already a battery hog. I guess it can help if you want to over clock a lot but there is absolutely no point in doing that.
In older legacy phones if you wanted to over clock because the cpu would be so weak, like 600mhz then you would have to overvolt to over clock to like 1ghz if you were lucky. Our devices are 1.5 ghz dual core and sense isn't THAT bad. There's no point in doing overvolt in this phone though.
PS, check out my rom in the development section.
Sent from my HTC_Amaze_4G using Tapatalk 2
SuperAfnan said:
Don't worry.
Undervolting is basically adjusting the voltages so the cpu uses less voltage aka electricity. It helps a little but it can make your phone unstable so watch out. Of you undervolt use the system tuner app on the market. You should definitely under clock if you want to save power too. When you undervolt be sure to underclock, and don't do it too low or your phone might freeze! That's why your shouldn't go so extreme on it.
Overvolting is basically adding more voltage to the cpu. There is no point in doing it for our amazes to be honest. It is already a battery hog. I guess it can help if you want to over clock a lot but there is absolutely no point in doing that.
In older legacy phones if you wanted to over clock because the cpu would be so weak, like 600mhz then you would have to overvolt to over clock to like 1ghz if you were lucky. Our devices are 1.5 ghz dual core and sense isn't THAT bad. There's no point in doing overvolt in this phone though.
PS, check out my rom in the development section.
Sent from my HTC_Amaze_4G using Tapatalk 2
Click to expand...
Click to collapse
I just saw it in Venom Tweaks and was curious. The most I underclock to is 1 GHz; cuts down the CPU maximum by a third and doesn't hinder performance to much. What voltage would you recommend at that clock speed?
P.S. I have I plan on flashing it to try it out when I get WiFi access. Trying to cut down data usage since I don't have WiFi at home.
Sent from my HTC_Amaze_4G using xda app-developers app
Capgun_Homicide said:
I just saw it in Venom Tweaks and was curious. The most I underclock to is 1 GHz; cuts down the CPU maximum by a third and doesn't hinder performance to much. What voltage would you recommend at that clock speed?
P.S. I have I plan on flashing it to try it out when I get WiFi access. Trying to cut down data usage since I don't have WiFi at home.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
1ghz is perfect. As for voltage it really varies but I subtract 75 or 50 mv from all voltages.
PS. Oh nice, hope you get wifi soon then.
Sent from my HTC_Amaze_4G using Tapatalk 2