any help????
my wife's battery life is so bad
I use set cpu and turn down the speed when the screen is off. My battery performance is almost equal to what I used to get from the Droid1. It'll last me all day with moderate usage,
I use SetCPU as well but I am a little more aggressive.
ScreenOff = 300Mhz
Less than 50% Batt = 800Mhz
Less than 25% Batt = 600 Mhz
I also have it set to throttle down to 800Mhz when temp goes above 50C but thats not really about Battery Life.
You really don't notice the lowered CPU at all. Especially during phone calls or TXTing.
I think the real savings is in the screen off. My guess is the stock automatic scaling is not doing a good enough job on it's own when the phone is sleeping. and most of our battery life was being blown away in standby.
With those settings I have been able to go almost a day and a half on a charge with moderate use where before even light use would only get me 6-8 hours.
And that is with a BP6 not a 7!
With those settings as your battery goes lower the longer it will take to drain. It really was remarkable.
Computer Dreams said:
any help????
my wife's battery life is so bad
Click to expand...
Click to collapse
Disable WiFi or BlueTooth ..
I got 12% battery drain in 17 hours, standby. I'm not a pro at android but I might give a little tut. on how to save battery life to the max. Atleast, it works for my P500 so it should work for you & for any other android device as well.
Uninstall every unnecessary app, including system apps (those apps, that does not mess up with the system stability - If you uninstall Email app, you will not solve your problems with Gmail app).. same with Messaging. That said, leave as minimum apps in the background as you can. App killer does not solve this problem, it just closes bg apps - they restart after some time. I'm using ATK (Advanced Task Killer), It usually kills 1 - 3 apps, so.. I have a minimum of apps running in the bg.
Basic stuff.. turn off your 3G, wifi, bg sync, gps when not in use. If you need to check your email, use 2G network only option, not 3G. Use 2G always when you don't need 3G speed. Screen brightness is not that important if you set it to anywhere below 70%. It should not drain the battery that fast.
Setcpu - profiles - governors--
My profiles are as follows
Charging - 480min - 748max
Battery <90% - 245min - 600max
Battery <70% - 245min - 600max (U can live with one profile for the battery, I have 2 in case I want to change the 2nd profile)
Screen off - 122min - 245max -- This is what saves my battery in standby.
The governors are ondemand for usage & conservative for screen off.
I'm using Void.echo rom with tapps & gapps modules, uninstalled everything I don't need.
I hope this helps If anyone has a better idea on how to save battery life, please share yours as well.
Thanks for your post, but actually most background apps don't drain battery. I have made lots of experiments (removing system aps, preventing autorun etc., and I don't see any major difference in battery life. So now, I'm on stock 2.2 and I'm now at 80% after almost 30h use: about 20 min talk, 10-15 min wi-fi (mail), 10-15 min EDGE. The latter by the way drains battery more than wi-fi. So instead of messing with system apps I recommend putting the phone in airplane mode during the night and as mentioned in the above post - not using 3G when not needed (EDGE has decent speed).
thats the why linux works !!! use all the memory u possibly can...These Microsoft *****es have changed the way computers were supposed to be used not reinstalling windows and other crapware all the time..Switch to Debian while its still time
And i use these settings
screen off 245-245 powersave (otherwise phone gets hot Its summer in india)
600-245 ondemand otherwise
kopchev said:
Thanks for your post, but actually most background apps don't drain battery. I have made lots of experiments (removing system aps, preventing autorun etc., and I don't see any major difference in battery life. So now, I'm on stock 2.2 and I'm now at 80% after almost 30h use: about 20 min talk, 10-15 min wi-fi (mail), 10-15 min EDGE. The latter by the way drains battery more than wi-fi. So instead of messing with system apps I recommend putting the phone in airplane mode during the night and as mentioned in the above post - not using 3G when not needed (EDGE has decent speed).
Click to expand...
Click to collapse
If there are many apps running in the bg, phone runs out of ram, so it tries to free up some space constantly. I think that drains battery, not the apps themselves. As well as the more cpu power is used, the faster it drains battery. Airplane mode shuts off any connection, so either that or you could just shut down the phone during night. Hmm you could tell me how to prevent app autorun, i have not looked into that.
btw juicedefender does wonders with the phones battery i had a 2% percent over night normal mode (not airplane) no 3g/Edge/Wifi/Bluetooth active and just sleeping
sarfaraz1989 said:
thats the why linux works !!! use all the memory u possibly can...These Microsoft *****es have changed the way computers were supposed to be used not reinstalling windows and other crapware all the time..Switch to Debian while its still time
And i use these settings
screen off 245-245 powersave (otherwise phone gets hot Its summer in india)
600-245 ondemand otherwise
Click to expand...
Click to collapse
True about windows & linux hehe. You havent tried 122-245mhz on screen off? Ofcouse, it lags even when i receive an sms, it's something like this - the screen turns on, then after 2 sec. i hear a notification, then after 1 sec. i see the sms but that does not make any problems for me, it's extreme powersaving
I don't get the point of airplane mode while you're sleeping.
If you don't want to get calls while sleeping, shouldn't it be better if you turn off the phone?
I had a good experience with JuiceDefender until now too. Last night my phone was 100% and no airplane mode while sleeping. It drained only 3%.
SoundTone said:
If there are many apps running in the bg, phone runs out of ram, so it tries to free up some space constantly.
Click to expand...
Click to collapse
From what I've read, Android doesn't swap. It'll just kill the background apps on it's own. I don't think there even is a swap unless you root, rom and create one on your uSD.
rapharias said:
I don't get the point of airplane mode while you're sleeping.
If you don't want to get calls while sleeping, shouldn't it be better if you turn off the phone?
I had a good experience with JuiceDefender until now too. Last night my phone was 100% and no airplane mode while sleeping. It drained only 3%.
Click to expand...
Click to collapse
It's more convenient, because the on/off process is quite slow...in contrast - airplane mode on/off is 3-4 secs. In airplane mode you can still use wi-fi. Last night the battery drained only 1%
i read somewhere that changing the CPU speed doesnt change the voltage, thus it does not affect battery life... anyone can confirm this???
As far as I can remember from school, a logic gate uses more power when switching, thus a higher frequency would also mean higher power drain (higher frequency = more switching of the logic gates), without voltage modification.
Voltage is changed in order to keep stability - higher voltage means a more stable logic signal, and a faster switching gate, and thus people reccomend using a higher voltage for higher frequencies/lower voltage for lower frequencies.
Thus, a CPU with so many logic gates does not operate just like a simple resistor. In fact it is worse, because when you use higher voltage AND higher frequency power drain is increased much more.
On the other hand, most modern CPU's simply deactivate CPU regions when idling, so, in case of our hardware (constant voltage) there should not be such a great difference when idling (most of the CPU is powered down). The only thing is for the phone to be REALLY idling (no background tasks eating too much of the CPU when screen off).
Basically, what this means is that if you want extreme power saving use a governor with 128MHz minimum and have as few background services as possible (or at least the ones that are there should be optimized for the least CPU usage).
Now I use the standard governor (248 - 600) and I thing my idle power drain is OK.
I guess I will test a governor that is plain 600MHz and one wit 320 or 480 as a minimum, in order to see if power drain is higher when using a lower lag configuration.
And, just as a guess, if background tasks are triggered by timers, a governor with just 600MHz (or 320 - 600 or 380 - 600?) could (just a wild guess) mean that background tasks take less time to execute, and leave the CPU to si more in IDLE mode, causing a very similar power drain as an extreme power saving governor. But this is just a guess, i have not tested it yet. And it also depends on what apps you have (what the apps do when phone is sleeping).
Basically, my best advice would be to watch the apps (after you install a new app, wait for a night to see if the new app causes a higher drain; if it does, search for another app that does the same thing)
spaic said:
As far as I can remember from school, a logic gate uses more power when switching, thus a higher frequency would also mean higher power drain (higher frequency = more switching of the logic gates), without voltage modification.
Voltage is changed in order to keep stability - higher voltage means a more stable logic signal, and a faster switching gate, and thus people reccomend using a higher voltage for higher frequencies/lower voltage for lower frequencies.
Thus, a CPU with so many logic gates does not operate just like a simple resistor. In fact it is worse, because when you use higher voltage AND higher frequency power drain is increased much more.
On the other hand, most modern CPU's simply deactivate CPU regions when idling, so, in case of our hardware (constant voltage) there should not be such a great difference when idling (most of the CPU is powered down). The only thing is for the phone to be REALLY idling (no background tasks eating too much of the CPU when screen off).
Basically, what this means is that if you want extreme power saving use a governor with 128MHz minimum and have as few background services as possible (or at least the ones that are there should be optimized for the least CPU usage).
Now I use the standard governor (248 - 600) and I thing my idle power drain is OK.
I guess I will test a governor that is plain 600MHz and one wit 320 or 480 as a minimum, in order to see if power drain is higher when using a lower lag configuration.
And, just as a guess, if background tasks are triggered by timers, a governor with just 600MHz (or 320 - 600 or 380 - 600?) could (just a wild guess) mean that background tasks take less time to execute, and leave the CPU to si more in IDLE mode, causing a very similar power drain as an extreme power saving governor. But this is just a guess, i have not tested it yet. And it also depends on what apps you have (what the apps do when phone is sleeping).
Basically, my best advice would be to watch the apps (after you install a new app, wait for a night to see if the new app causes a higher drain; if it does, search for another app that does the same thing)
Click to expand...
Click to collapse
I don't know about CPU's as much as u, but simple logical thinking helps here.. Low frequency + minimum of bg tasks = great power saving, I have now used the phone for 36hours without charge, 61% battery left. That is not only idling, i write about 50 to 150 sms a day & use the phone for other stuff too. So, those governors & frequencies i mentioned earlier in this post, helps a lot.
fransisco.franco thinks otherwise read the his post that contains the link to his rom devoid.francov6(ROM is cool btw and unfortunately i have a slow sdcard )
I think the first post is by far the best I have seen so far.
Sent from my LG-P500 using Tapatalk
Wow, only 1% all night?
I'll take a deeper look at your tips!
I use devoid.franco with franco.kernel v12. From all ROMs I've isntalled, it's the best: great performance and long battery life.
I get 5% battery drain in 7:30 hours (at night), without doing anything special, without running a custom ROM and without uninstalling apps. I just make sure GPS, Bluetooth, WiFi and data are off before going to bed.
I find that setting setCPU to 450 mhz (900 mhz because of the dual core) the phone works perfectly for my day to day use.
Would underclocking to 450 mhz from 1000 mhz save a lot of battery, or the process of underclocking would take battery to make it equivalent to leaving regular clock.
Not really sure. I've had it set so it goes to 400mhz when the screens off since I had it. I'm sure it helps a little but i doubt it's going to make you get as extra day of battery or anything
Sent from my MB860 using Tapatalk
primeboss said:
I find that setting setCPU to 450 mhz (900 mhz because of the dual core) the phone works perfectly for my day to day use.
Would underclocking to 450 mhz from 1000 mhz save a lot of battery, or the process of underclocking would take battery to make it equivalent to leaving regular clock.
Click to expand...
Click to collapse
I have to intervene here. When you set it to 450 its not 900 because of the dual core. the cores dont add up speeds.
The Atrix doesnt have a 2ghz processor because its 1ghz but two cores.
But to answer your question - yes you would save battery, but the phone would be very slow because you would be at 450 (not 900 or 1ghz)
i have mine set at 600mhz and its fine through the day though i dont do it for battery but to keep it nice and cool(that 1ghz makes it 60C+ easy) but i guess it helps
You have to consider that a lower clock speed means that the CPU must process things for a longer period of time. Sure at a lower speed it will process using less power but the longer period of time it needs to process may mean that the total power consumption is still the same or even higher since the CPU still consumes power simply by being turned on.
palmboy5 said:
You have to consider that a lower clock speed means that the CPU must process things for a longer period of time. Sure at a lower speed it will process using less power but the longer period of time it needs to process may mean that the total power consumption is still the same or even higher since the CPU still consumes power simply by being turned on.
Click to expand...
Click to collapse
+ 1. I'm starting to believe that even the screen-off profile (I have it set on the lowest) has a negative effect on the battery if you use your phone a lot and keep turning the screen back on all the time! Am turning it off now to try..
Sent from my Motorola Olympus using XDA Premium App.
I've install Rom Toolbox,
and i saw there is a "CPU slider" where i control the clock speed.
i've put it to 1000MHz instead of 1200MHz and tested it for several days
i really dont feel any difference in performance.
browsing seems same, games like asphalt is equally smooth.
heating is similar, equally warm.
the only difference is quadrant benchmark.
1200MHz scores 3200-3400
1000MHz scores 2600-2900
frankly speaking, i'm not sure if there's any difference in battery life.
is there any way to accurately test whether the clock speed affects the battery life?
i've seen other threads, where there are very different opinions.
some say it will improve battery life, and some say its worst.
http://forum.xda-developers.com/showthread.php?t=726019
Quote: (SetCPU doesn't make a difference in battery life, it can only shorten it. The kernal already has the best settings for CPU speed built in.)
http://forum.xda-developers.com/showthread.php?t=1305465
Quote: (if you are able to stand the side effects of underclocking, it will surely boost your batery life.)
On my SGS2 program called CpuSpy shows that 1200MHz is about 1% of total cpu time (remember that governor is ondemand and CPU is at 1200 only when need it). If power consumption is directly proportional to clock speed by limiting it to 1000MHz you will get about 20% less power usage by 1% of time... looks like 0.2% power saved ? Soo if Your phone works for about 48h on one charging this way You can get about 6 extra minutes. It's just my guess...
Also have to consider if slower cpu causes screen to eat power for longer time... (because You have to wait longer for operation to complete)
slig said:
On my SGS2 program called CpuSpy shows that 1200MHz is about 1% of total cpu time (remember that governor is ondemand and CPU is at 1200 only when need it).
If power consumption is directly proportional to clock speed by limiting it to 1000MHz you will get about 20% less power usage by 1% of time... looks like 0.2% power saved ? Soo if Your phone works for about 48h on one charging this way You can get about 6 extra minutes. It's just my guess...
Also have to consider if slower cpu causes screen to eat power for longer time... (because You have to wait longer for operation to complete)
Click to expand...
Click to collapse
HI, thanks for replying. I understand what you mean. the phone dont operate at 1200MHz all the time. but when using browser, and playing games, such as asphalt, it runs at max CPU usage almost the entire gaming duration.
Anyway.....
the real question is whether the clock speed is directly proportional to the battery consumption.
while reading your post, i thought of a brilliant ideal how to verify this.
the CPU slider not only allows you to set the max CPU speed,
you can set the min CPU speed as well.
So, i thought of an experiment, lets set the min & max CPU to 1200MHz,
this way, the phone will be running constantly at max CPU even when its idle.
let the phone be turn on till it run out of battery, record the time, T1.
then repeat again with max and min CPU set to 1000MHz.
record the time it is turn on till it run out of battery, record time as T2,
then compare T1 & T2, this could certainly work.
it would be nice if any member here happens to have 2 sgs2, and tried them ;-)
There are two more things to consider
1. CPU is not the only element that consumes power.
2. SGS2's Exynos is always clocked at 200MHz when the screen is off - check if this minimum slider affects that too.
Please let know how your experiment goes.
Regards
when the screen is off, the phone will be in "deep sleep" state. i think thats less than 200MHz.
anyway, i wont be doin this experiment any time soon.
you see, this is my only phone, i need to use it.
i dont have much oportunity to leave it and wait for it to run out of juice.
still, i'll try it when i have the chance.
Just want to know everyones opinion on if it can really save life for the S4. Cause the way I see it is if the cpu is constantly being clocked down/up for instance, when my screen is off I have it so that cpu is at about 400mhz and when the screen comes on it boosts back up to anywhere between 1200 and max
If you're driving, and you slow when down to say 30mph and slam on the gas to get up to 100mph instead of steadily getting there, you're going to use a lot more gas. So if it is the same with the phone, aren't I using more battery life than saving?
Markymarc206 said:
Just want to know everyones opinion on if it can really save life for the S4. Cause the way I see it is if the cpu is constantly being clocked down/up for instance, when my screen is off I have it so that cpu is at about 400mhz and when the screen comes on it boosts back up to anywhere between 1200 and max
If you're driving, and you slow when down to say 30mph and slam on the gas to get up to 100mph instead of steadily getting there, you're going to use a lot more gas. So if it is the same with the phone, aren't I using more battery life than saving?
Click to expand...
Click to collapse
I'm not entirely sure, but with your example, doesn't that depend how long you're going 30 or how long your screen is off at a crack? If you turn on your screen for 10 minutes for every 20 it's off, I think it would save your battery more in the long run.
You use more gas in the car analogy as you have to overcome a ton or so of mass driving at 30 mph. Changing clock speeds faces no such resistance, so it won't be the same with the phone.
yes, the acceleration doesn't really affect the drain. the fact you're running at a higher clock speed is the drain. you can adjust your steps and max speed, thus saving a little bit of battery. undervolting can help to, but the cpu usually draws so little power that the savings may go unnoticed.