Related
So, I don't know if this is just my device or maybe already known. I don't see it here(or google) so I am going to post this so others can find this info faster than the 2hrs it took me.
Some Li-Ion batteries have a low max charge rate. Meaning you cant "over-current"(mA "Milli-Amps" or A "Amps") them too much(saves life). Well my Razr just showed me this. This can allow you to charge the battery faster if you have one that is tolerant of the "over-current".
Apparently maximum for the Droid RAZR is somewhere between 850mA and 1000mA
Tried using an HTC @ 1A and no joy.. wont charge.. actually says charging.. but the battery seems to have flipped the switch to not charge; and just continues to discharge normally; even the hidden status(dial *#*#4636#*#*) says charging but obviously not! Tried different HTC models and different cables. I am now only using my Moto supplied cable.
Even after it was dead. It would show the charging screen @ 0% and the light would be red. Stating that you cant turn it on cause there is not enough juice to finish boot. It would never go Green no matter how long I waited(10-15 minutes) usually only takes 5 minutes.
Found my OG Droid charger; remembering that it was lower than 1A. It actually is 5v 850mA. Charging away!
Remember the stock charger is rate @ 5v 750mA - this means you can probably use chargers from 700ish to maybe 900ish mA. I cannot confirm these estimates. Anyone else seen any other rates work?
Hope this helps someone down the road. I know it would have helped me!
MODS - Please, if this is wrong info please DO NOT HESITATE to notify me/remove/edit my post. I just want the right info somewhere, cause it was not well documented anywhere i searched via google.
Also - Thinking more on the subject - this could be the "Authorized Charger" bull that Moto likes to put on its devices i.e. The RAZR flip-phone was notoriuosly bad about this. Even my old nextel "beep beep" had this problem with OEM chargers. Had to spend $15+ on the official one. Again - if this info is wrong in ANY way please fix it or remove it.
use official 850mA charger and be happy. Motorola also confirmed using 1A chargers without any problems but any ways original ones are recommended.
Brilliant, my problem now makes sense!
Couple of questions: What does this mean to charging via USB instead of mains? Is it the plug or the cable that is rated to a certain ampage?
One more question. I found another usb plug rated to 300mA. I presume using this will just mean the phone charges slower? It won't have any negative effect on the battery?
Sent from my XT910 using XDA App
Just adding my experience... Have been using an iphone wall charger w/ the usb jack on it and the supplied motorola cable. Its listed as 1000Mah. Battery Monitor Widget shows it charging around 945Mah. Doesn't get hot, charges like a bat out of hell. Down side is phone is about 60% unresponsive during the charge.
Found a little info on this. Apparently different cables, when plugged in, short different contacts to let the device know what it's plugged in to. Resistors change the current. Audio out can tell if it's plugged into a dock versus USB versus wall charger. The Verizon replacement didn't work for me, but an hard incredible one did. They both charged but only the htc recognized computer connections
Sent from my DROID RAZR using Tapatalk
My stock Razr wall charger is 750mA. I use a 1000mA car charger and it works fine - doesn't get hot and charges faster.
But sometimes you do have to be careful. I had a friend who's noob mother fried her Bionic with a charger that was too many mA for it to handle.
__________
Razr XT912 Verizon
HTC Eris via GingerShedBread
strange... my stock charger's rated 850mA.. maybe because i use international GSM version of RAZR.. but it charge just fine..
but even i tried charge it with blackberry's 700 mA charger or my ipod touch 1000mA charger it both charge just fine.. and it feels like the 1000mA charge slightly faster..
too bad i broke my old nokia n900 1200 mA charger..
I'm using an HTC 1A charger: the RAZR doesn't become hot while charging and it's charging faster.
The limit is 1A anyway.
kholk said:
The limit is 1A anyway.
Click to expand...
Click to collapse
dang! so i guess nokia 1200mA charger won't be any good then..
thanks for the info though.. i was thinking of getting myself a nokia charger after read this thread..
Ever since my first motorola I've noticed that the stock charger is 5.1 volts.
Charging with other brands always seem to give worse battery life.
My old Rizr only lasted a day when charged from the USB of my computer, but 6-7 days with the original part.
Some of that is apparent with my car charger too, it says it's taking charge, but sometimes it will run backwards with GPS running..
I experience the charger issue last night.
I had low battery when I went to sleep, put the cable in and it said charging.
Came late to work because the phone drained the battery instead of charging. I used a 5V 1.2A charger and its been working great until last night. And I noticed my original charger is 5.1V 850mA for the Razr.
You learn something new every day!
/J
I discovered today that, for some reason, my prime will not charge. The LED at the top isn't on either. I recall first using it this morning around 9am and it had 25% left but I needed to travel so I didn't use it. When I wanted to use it again, hours later, the meter showed that it had 36% which didn't make sense. However, I am able to connect it to my computer to transfer files.
Here's some info just in case:
-My device is unlocked
-I had the current Primalicious Rom when I discovered the problem
-I did a factory reset in hopes to solve the problem (didn't work)
-I installed a different rom (AOKP, but didn't work)
-I installed another rom (Virtuous, hasn't worked either)
-I've tried charging my phone with the Prime's power source and that works
Does anyone have any advice?
Thanks in advanced.
Either the cable or the charger is bad. You can try the various "fixes' in the forum such as bending pins, freezer, etc just in case. In my case, I could transfer data and trickle charge via USB but nothing else. Turned out to be a cable problem.
TechAnimal said:
Either the cable or the charger is bad. You can try the various "fixes' in the forum such as bending pins, freezer, etc just in case. In my case, I could transfer data and trickle charge via USB but nothing else. Turned out to be a cable problem.
Click to expand...
Click to collapse
Maybe I have the same case as you but I decided to leave it on the charger to see if anything would change and I was able to go from 17% to 82 % in 5 hours but I usually takes a shorter time to fully charge. The weird thing is that I never get a notification that the battery is charging and in the battery portion of the settings it says the battery isn't charging even when I'm plugged in.
Well, I went to Best Buy today to see if their cable would charge my tablet and it did so I'm off to get a new cable. Thanks for the help!
It may not be the cable. Check the charger as well. A lot of the chargers have gone bad and caused the same problem
Sent from my ADR6425LVW using xda premium
If you are trying to charge by usb, you have to have a usb 3, not 2 port as the Prime requires 15v to charge and the usb 2 port does not provide that.
If you search these forums, it has been discussed in several threads, so that may be your problem. You need to use the charger that was included with your prime. Even car chargers not rated properly will not work as well.
gunz.jones said:
It may not be the cable. Check the charger as well. A lot of the chargers have gone bad and caused the same problem
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
It might just be my charger; it only charges my cell phone right now.
Dnakaman said:
If you are trying to charge by usb, you have to have a usb 3, not 2 port as the Prime requires 15v to charge and the usb 2 port does not provide that.
If you search these forums, it has been discussed in several threads, so that may be your problem. You need to use the charger that was included with your prime. Even car chargers not rated properly will not work as well.
Click to expand...
Click to collapse
Thanks I'll try usb 3.0 and see how that works out.
Dnakaman said:
If you are trying to charge by usb, you have to have a usb 3, not 2 port as the Prime requires 15v to charge and the usb 2 port does not provide that.
If you search these forums, it has been discussed in several threads, so that may be your problem. You need to use the charger that was included with your prime. Even car chargers not rated properly will not work as well.
Click to expand...
Click to collapse
Actually, that's false. It does not need 15v....it will work with 18 watts at 12x1.5 and 15x1.2. The Prime by itself will charge on USB 2.0, but very slow. The only difference with 3.0 is higher amps (.3-.4 average higher) from usb 2.0. The voltage is the same. It has been discussed, but I don't think you read the posts. Wikipedia has an excellent article on USB you should check on. Also, the charger that came from Asus have a variable rate from 5x2 to 15x1.2 based on resistance via the wall adapter. It's the same charger used on the 101. The 201 has better power management and can even take a charge through USB 2.0 with low usage, or at least keep the battery at a stable number. OC users will not have such success under use and wifi other than a slower dissipation of the battery. Check the 101 forums regarding the use of other chargers, both car and home, that work well. I use an adaptaplug from Radioshack that is 12x1.5. Unlike some of the problems people have been having with faulty no-name 3rd parties and the high rate of OEM failures, there have been some conventional and not-so-conventional projects that have been successful and not damaging to the tablet. Note: With the dock, you will need 12 volts at least for it to register correctly and charge since the dock battery is rated (if i remember correctly) at 7.5 volts. Maybe my results may differ based on OC kernels and their voltage tables as well as rom choice as far as battery usage. Just some facts to throw out there for readers and the OP for a better idea of what will and won't work.
Sent from my Transformer Prime TF201 using xda premium
RachellehcaR said:
It might just be my charger; it only charges my cell phone right now.
Thanks I'll try USB 3.0 and see how that works out.
Click to expand...
Click to collapse
Its the cable. I was also able to/charge my phone. I've found that the cable is quite delicate and doesn't like to be tied up, etc.
I have just had the same problem. Stock charger worked yesterday then wouldn't work today. Just stopped. Wouldn't light up or charge did not know why. I read a few of these forms and they kept talking about pins in the usb.
I got a torch of and looked at all the connection on both sides of the cable and the wall charger. Looked fine for my untrained eye
But i thought i would play with the pins in the usb cord side anyway. Plugged everything back in and it worked fine. Job done thanks to xda forums.
Mine stopped working a few months ago, so I unplugged it from the wall for a few days and left it alone. Decided to try it a few days later and it worked no problem. No idea what the issue was lol... Everything was plugged in fully and properly, and the outlet I used was the same both times.
Sent from my ADR6425LVW using XDA Premium.
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Slow Charge Message
arisch86 said:
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
Same here. Glad to hear it is not just me. I just got off with NA HTC Tech Support. There official stance is that they do not recommend or support using any device other than the official charging cable and plug in device. They went as far to say that they do not support charging in the car. I just about flipped my lid on the phone.
Here is the link to their site: http://www.htc.com/us/support/howto...783&p_name=droid-dna-by-htc-(verizon-wireless)
"Only the power adapter and USB cable provided in the box must be used to charge the battery"
I was told by Verizon that this was just a scare tactic, while HTC says I am not getting the right charge and they have no answer since they do not support DC charging in the car. Any info people have is appreciated. It works fine with Hard Wired DC -MicroUSB, but not with any USB Plug in.
Any apps that would help me measure the amount of charge it is getting?
Thanks in advance.
What are the specs on your car charger?
Sent from my HTC6435LVW using Xparent Red Tapatalk 2
So odd that they would do that, especially with the power draw of the phone. However you can charge using the battery packs?
My car adapter is a Macally USB car adapter model carusb10 output 5v/2.1 amp x1 500mA x2.
As for my house adapters the RCA 2 port USB wall adapter. 2.1 Amp x 1 or 1000mA x 2 I believe.
Sent from my HTC6435LVW using Tapatalk 2
Everyone with a stock DNA unplug your charger and flip it around. As in flip the prongs. It should give you this message even with the HTC supplied one. Or try this. When you use another charger and it gives you that message unplug it and flip it. It should straighten out. I dunno. Something about the way the power is drawn.
xcesivemastub8ah said:
Everyone with a stock DNA unplug your charger and flip it around. As in flip the prongs. It should give you this message even with the HTC supplied one. Or try this. When you use another charger and it gives you that message unplug it and flip it. It should straighten out. I dunno. Something about the way the power is drawn.
Click to expand...
Click to collapse
I have tried several different USB adaptors, from Razorfish(BestBuy), Belkin single USB input 2.1amp, innocell (RadioShack) dual SUB 3.1amp. Same problem on all.
On the other hand, any direct Wall connection with USB cable attached seems to work fine.
Also, I have the Motorola p4000 battery backup and when I plug that in, it also works fine and views it as AC.
Swapping the pins didn't work for me, same issue. Its a pita for me especially charging in the car because when using phone for navigation it charges so slow that it can't actually charge my phone and my battery decreases. I've went the route in the car I use my nexus 7 charger connected to an inverter.
Sent from my HTC6435LVW using Tapatalk 2
From my phone conversation with Seth from HTC Support, the slow charging warning is due to the update because the update incorporates the faster charging feature that qualcomm & htc have referenced too recently (can't remember what its actually called). The phone has a new type of charging setup that makes it charge faster than some other phones.
Unfortunately some chargers (wall/car) dont supply enough voltage to activate the charging feature so while the phone does charge fine (it charges at standard phone charge rate) it cannot charge at the faster rate due to the charger.
He states that this will not harm the phone and ther phone will charge fine and it a normal time. You can disregard the warning. For those that like the faster charge rate, you have to use the right charger/cable.
Before the update our phones were mostly charging at the slower rate and that's why most didn't see a warning unless the cable being used was below the standard rate of charge.
Hope this helps
arisch86 said:
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
Why are there so many problems about this thing lately even me, I experience this most of the time
When I use the Best Buy 2.1 amp wall charger I still get the message.
I'll need to find my oem wall charger.
So far every one I have gives this message.
I haven't seen this message at all on any of my charges but I haven't charged in the car yet. My battery usually lasts for more than the while day so I just charge at night.
Sent from my HTC6435LVW using xda app-developers app
Well with the faster charging enabled it does charge pretty quick especially using my nexus 7 wall adapter, even with my Nokia Qi pad. But man that last percent takes a while.
As of now I'm using supercharged hatka ROM slim 3.0.3 and getting good battery life. Even in the middle of nowhere where 75% percent of the time when I'm in the plant its searching for signal. I'll leave work after 8 hours and still be at 60%
Guess you can say its the only negative I have for the phone. Trust me the battery life is much better in the plant then my old bionic. I use to have to change the standard battery after 4 or 5 hours as it was completely dead.
Sent from my HTC6435LVW using Tapatalk 2
Last night I received my daughters replacement Rezound from the warranty company. It came with a 1 amp wall charger.
I plugged it into my DNA and did not get the notice of slower charging and it charged quicker than I've ever seen it.
Too bad my 2.1 best buy one won't.
The quick charge capable chargers must output just slightly higher voltage to trigger the rapid charge mode.
I'll experiment some day and see.
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
I have the charger that came with the phone it it fully charges my DNA in 2 hours from 3%
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
I kinda figured it was something with the pins if I wasn't voltage offset.
I did find that one of my car chargers from best buy runs in quick charge. The cable I fixed, rather than using a usb cable in a slot on the charger.
The best number 2.1 amp wall charger uses a data type cable.
Maybe I'll check into shorting the pins on that sucker to get quick charge mode.
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
The phone is doing more than checking pins now. I have a 2.1 Amp dual charger with pins shorted and get the warning. It happily charged in AC mode before the update. The charger can also charge a nexus 10 at 2 Amps. I'm guessing the kernel devs will have to locate the source of the warning. I thought the resistance between the data pins might be the trigger, but there is no difference between the HTC charger and my dual charger. It does seem my car charger is unaffected.
I have found that to trick the phone into AC mode you have to short the the actual cable. Hence strip the insulation off the wires and short the data wires together. Has worked for me on all my chargers.
Sent from my HTC6435LVW using Tapatalk 2
This message does not have to do with the update. I have still not updated my DNA and have been struggling with this for about 6 or 8 months. I am on 2.08. The issue has continually gotten worse since the first time I saw it. At first it would just appear about 1 in 10 times I plugged it in to a car charger. It then got to the point where it would only not show the message with a certain car charger. Now it is showing it on the one car charger that works, but if I mess around with it and unplug and replug it a few times it will finally charge normally. The last few days it has started showing the message on the OEM charger. I have cleaned out the port on the phone and cables quite a few times now, but it doesn't help. I found that doing that only helps if it gets really full of lint and the cable rocks in the port causing it to loose connection if you move it, but it does not change the slow charging message at all. The phone is also definitely not charging at full speed when that message is shown. If I have it plugged in and it shows that message my battery actually drains if the screen is on. With the screen off I only gain about 10% per hour. I am not sure where the issue is, but I think it is different in different circumstances. In my case I think it is the phone itself, but from what I have read about others experiences it seems their problem might be the charger/cord. I hope this gets sorted out soon.
Clay333 said:
This message does not have to do with the update. I have still not updated my DNA and have been struggling with this for about 6 or 8 months. I am on 2.08. The issue has continually gotten worse since the first time I saw it. At first it would just appear about 1 in 10 times I plugged it in to a car charger. It then got to the point where it would only not show the message with a certain car charger. Now it is showing it on the one car charger that works, but if I mess around with it and unplug and replug it a few times it will finally charge normally. The last few days it has started showing the message on the OEM charger. I have cleaned out the port on the phone and cables quite a few times now, but it doesn't help. I found that doing that only helps if it gets really full of lint and the cable rocks in the port causing it to loose connection if you move it, but it does not change the slow charging message at all. The phone is also definitely not charging at full speed when that message is shown. If I have it plugged in and it shows that message my battery actually drains if the screen is on. With the screen off I only gain about 10% per hour. I am not sure where the issue is, but I think it is different in different circumstances. In my case I think it is the phone itself, but from what I have read about others experiences it seems their problem might be the charger/cord. I hope this gets sorted out soon.
Click to expand...
Click to collapse
It could be the charging equipment your phone or it could also be the power source not providing enough power to the device for it to charge fast so it charges slow.
Sent from my HTC6435LVW using XDA Premium 4 mobile app
Hi everyone,
I have just swapped my Galaxy S3 to a HTC One X+ because I couldn't stand Samsung's Touchwiz, and I love Sense 5. The downside is the charging times on this new phone are pretty laughable!
Now I know different cables can give different currents consistently, but I have three cables (one at work, one in car, one at home) that would all deliver 1000mA to my GS3 and I could go from 10% to 100% in about 90 minutes, about 1% per minute, it was great! Battery life on this phone never degraded so I know 1000mA wasn't damaging at all (all GS3s can take a maximum of 1A).
I've now moved over to the HOX+ and it's taking absolutely forever to charge, between 3-4 hours to charge from low. I simply can't wait this long, it's beyond a joke :crying: I've checked Better Battery Stats and my battery usage is about the same as my GS3 when unplugged (about 4-5% per hour) which is fine, so why the difference in charging times?
On my GS3 I had an app which showed me charging current that was specific to GS3s and was very reliable, but I can't seem to find a reliable app for the HOX+, the one I have is Battery Monitor Widget and it reckons I'm charging @ 330mA and I'm currently at 22%, that can't be right can it?
Here is what my phone is says when charging "Charging (USB)".
In the past hour it's done about 20%.
Sent from my HTC One X+ using xda app-developers app
Keydogg1 said:
Here is what my phone is says when charging "Charging (USB)".
In the past hour it's done about 20%.
Sent from my HTC One X+ using xda app-developers app
Click to expand...
Click to collapse
Erm thats the issue. When you charge using the AC (By cable to the electric socket) it says "Charging(AC)" . This usually takes me from 10-100% in about 90 minutes with the HOX+.
Somehow either you are connecting it to a usb hub (laptop or a computer) which is pretty slow compared to the AC, or your phone is mixing up the AC and USB currents. So an advice, use an electric socket and make sure it says "AC" in the power tab. IF so, check the charging time you should find it similar to that of Samsung.
I also think usb 3.0 is faster in charging than 2.0 ? If you are on a new pc with a new motherboard you should find your sockets 3.0, so don't use a usb hub especially if it says usb 2.0 since it will be pretty slow.
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Keydogg1 said:
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Click to expand...
Click to collapse
Sorry.. I am kinda sleepy so I posted without saying any thing. Anyway I wanted to post a pic of the text on ny stock charger. Says the following : output: 5v ~ 1A .
I will post a picture when I wake up in a couple of hours.
Sent from my HTC One x+ using XDA developers app
Ghand0ur said:
Sorry.. I am kinda sleepy so I posted without saying any thing. Anyway I wanted to post a pic of the text on ny stock charger. Says the following : output: 5v ~ 1A .
I will post a picture when I wake up in a couple of hours.
Sent from my HTC One x+ using XDA developers app
Click to expand...
Click to collapse
No problem! The charger I am currently using is a 5V/2A (for tablets) and has worked fine for every phone previously, giving 1A current.
Keydogg1 said:
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Click to expand...
Click to collapse
dont ever use after market charger even though it is for tablet or note samsung...i tried and it is prety damn slow...
so just use your htc/stock charger...it will be fast charge...2hr the most maybe less...
anyen said:
dont ever use after market charger even though it is for tablet or note samsung...i tried and it is prety damn slow....
Click to expand...
Click to collapse
That isn't necessarily true. This charger has been the fastest thing to ever charge my HTC Sensation and GS3, and come to think of it my Nexus 7 charges faster with this charger too. As I said earlier, I had an app on the GS3 which showed it was outputting 1000mA (maximum the GS3 allows) and it would charge that phone in around 90 mins. According to the HOX+ app I have I'm only getting 330mA. Whilst I agree that poorer after-market chargers often give dubious results I'm confident that this isn't the charger's fault.
I'll try the a HTC charger when I get home, but the other night I had it on charge with the HTC charger and it didn't seem to move very quickly.
I'll just say what I know from experience with my HOX+: it only seems to be charging in a normal (and pretty fast) way with the original, from the box, charger.
I tried charging it with the charger from a Desire Z - slow; charger from Desire S - slow; a Nokia charger - slow.
I also noticed that while the Desire S or Z can get charged while being used, when using a car charger (a Nokia one), the HOX+ seems to be using more current, and it ultimately dies. It happened this summer, so this might be an issue.
geojoking said:
I'll just say what I know from experience with my HOX+: it only seems to be charging in a normal (and pretty fast) way with the original, from the box, charger.
I tried charging it with the charger from a Desire Z - slow; charger from Desire S - slow; a Nokia charger - slow.
I also noticed that while the Desire S or Z can get charged while being used, when using a car charger (a Nokia one), the HOX+ seems to be using more current, and it ultimately dies. It happened this summer, so this might be an issue.
Click to expand...
Click to collapse
I think you're right! I tried my wife's HTC One S charger last night (because the HOX+ doesn't come with one) and it changed to Charging (AC) for the first time. I have to say this is a massive let down for me, my car charger saved me so many times with my GS3 (for example I drove to Scotland and used GPS all the way, and the phone still charged right up at the same time) I'm not sure I can handle it not being able to cope with other chargers.
I find this extremely frustrating Is there not a hack to get around this with root?
I'm not sure about the Samsung, but the HTC will only go into the fast/AC Charging mode when it see the Data+ and Date- signals shorted on the USB port. This can be designed into the charger, such as the factory HTC wall charger, or you can buy "charging only" cables and then use any USB charger to get your HTC to go into AC charging mode. These charging only cables are tough to find, but amazon does sell them. Keep in mind that the charging only cables will not transfer data at Data+ and Data- are shorted. Once you are in AC charging mode, the phone takes over and determines how fast to charge. At low battery levels (less than 80% or so), the charging rate can be as high as 1000ma/h or the maximum the charger is rated to deliver. If the charger is rated to deliver more than 1000 ma/hr, the most your phone will draw is 1000 ma/hr.
Now there is another variable, the cable itself. Cheap cables sometimes have too much resistance to pass 1000ma/hr and can be the problem as well.
One other issue is the number of knock off chargers and cables out there. Beware of e_ay. You may not be getting what you think you are.
One final note, Apple designs the ipod to look for the Data+ and Data- signals to not be shorted (opposite of HTC and most android manufacturers). So chargers that are designed to charge Apple devices will need the Charging Only cables to charge android devices in the AC charging mode.
So if I didn't confuse myself, hopefully this will answering some charging questions. I've researched this and have tested many chargers and cables.
It appears to be the connection in the phone. We have tried multiple charging cords, but some don't work at all, or others just give a very slow charge. I have looked for a spare battery with separate charger, but there doesn't seem to be much available for this phone. Will a battery from another model work in this phone? Does anyone have any other suggestions?
You may have already tried this, but look for a 5v charger that's at least 2A.