Every month I have paid much money for phone and internet fee(9800 yen). I want to disable internet connection because it is not necessary for me.
thanks in advance
you can create a new internet connection and replace the default with it.
thanks for reply but how to make new connection.
Hello. What do you mean? You mean I can use it for a non-softbank account? (via 3g?) Of course, I suppose we could just delete the whole softbank account, and therefore it would not be able to "connect" via 3G, and we could connect via a wireless account, but then softbank mail would not work, right? I wonder if it is possible to just disable connecting to the internet via explorer.... any ideas?
@taicyber: i ran into a similar problem. sometimes while in my carrying case, my keitai would connect to the internet via internet explorer, and my monthly fee for internet usage was much higher than it should have been. so i took a couple steps. first, i changed the internet button on the front of the phone to a different function (that's apparently the button that often gets accidentally pressed). after that, i changed pie's (pocket internet explorer's) start page to a local file (ie. the help file). that step solved the majority of my problems. what was happening when it auto-connected was that yahoo.co.jp was the start page, and that page has HUNDREDS of little pics and ads that refresh every few minutes and drive those packet amounts up. if you make it a local file you'll no longer have those mystery packets being sent. and it doesn't affect your mms/sms in any way. having the dummy file as a start page made it safe for me to change the pie button back to it's default function of opening up pie.
also, just for reference, i don't think you have to worry about the phone being connected to the 3g network too much. unless a page that refreshes itself frequently is opened, then no data is sent. the only problem i run into with 3g being connected is that it kills my battery faster.
thanks shunsai. I have experience like you said. and I also changed the button and defalult.html(in /windows).But I am not sure if my phone will connect internet via other way.
Hey it might not be super helpful in this case, but for me I disable gprs using a piece of software called 'NoData'. it will let you quickly switch on / off data connections. Search the forums for NoData and you'll find links to it.
The issue sounds specific to Softbank the carrier though so YMMV.
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (for the Hermes). It should currently be "BTPAN1".
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc")
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. I imagine this will drain your battery in a hot minute, so bring your charger.
UPDATE (28-Oct-2007): Attached are some more beta releases of patched intshare.dll. I've created versions for most of the adapter names people have requested. By renaming this dll to intshare.dll and copying it to \Windows, Internet Sharing will use TIACXWLN1 (or whichever dll you use) when Bluetooth PAN is selected. I.e., if you use this, you will not need to make the registry changes above.
This will handle the registry part, but of course you'll still need to set up the ad-hoc network on your own.
UPDATE (03-Nov-2007): I've attached a beta version of the patched Internet Sharing app. It's in its own cab so it won't overwrite your existing IS. This app replaces Bluetooth PAN with 802.11b/g Wireless Ethernet. No registry hacking required. This app is well suited to replace the MS version on cooked ROMs.
If you use an adapter other than TIACXWLN1 then replace intshare.dll just as before.
UPDATE (08-Nov-2007): Attached is v 0.9.1 of the Internet Sharing Mod. This update addresses the 10 minute disconnect bug most people have experienced.
best,
fluxist
This is the first thing I'll try when i'm at home again!
I can't believe this! Waiting for this since i got my Hermes. Thx for this development. This is the greatest effort since Hard-SPL and WM6 upgrade.
Now I can connect my XBOX360 to the Internet without starting my PC and sharing it over PC-LAN. USB-Charger is at the Front of the XBOX360.
I hope it will work.
You said the Max-Connections can be reworked. Does this mean it will support Ad-Hoc AND WLAN-Routing to many recepients too?
This worked for me too on a Kaiser/TYTN II
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
odessaranger said:
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
Click to expand...
Click to collapse
not sure what you mean by replacing the connection. With ICS, obviously you cant share your connection over BT while sharing it over WIFI. and you can normally use wifi to connect to another computer by using an ad-hoc connection and manually entering a private ip on the same subnet for each computer.
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
boniestlawyer said:
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
Click to expand...
Click to collapse
Were you able to use more than one client connected?
I'll admit..when I saw this my first thought was that this was another "How can I do internet sharing via wifi" and the title was just misleading..instead I find myself very impressed with your accomplishment. Very well done! As a "hack" untill you figure out how to mod the dll which I'm sure is only a matter of time now that you have pointed everyone in the right direction, you can export the registry key for both the Bluetooth adapter and the Wifi one and "import" whichever one you want to use at a given time...it's not pretty but it should work.
Some issues of concern would be that the AP is wide open and can be connected to by anyone with no password etc...the bluetooth pairing allowed some security but using the wifi doesn't have the same shared key protection...or am I missing something obvious?
fluxist said:
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
When I used it I was only able to get one client to connect, however there is a reg value, HKLM\Comm\BTPAN1\Parms\MaxConnections that may help if it is changed from 1 to 2 (or whatever). But I haven't tried.
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. So that's a good thing, although I imagine this will drain your battery in a hot minute, so bring your charger.
I was going to release a patched intshare.dll so that the normal Internet Sharing utility can do this, but I'm having trouble changing the section addresses in the dll to the right values after I add data. If anyone knows how to do this PM me and I'll give you the details.
best,
fluxist
Click to expand...
Click to collapse
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
I ran into same issue with XP internet sharing. Another workaround is to have a linux machine do NAT( since you can specify the IP used there) to whatever other clients you want and have it connected via bluetooth dun or bluetooth PAND (which is the solution I use to give internet to my replaytv and a couple of laptops in the house)...my edge connection is my main internet feed..a cacheing proxy such as wwoffle, squid of my personal preference "polipo" helps alot to when using gprs/edge etc since it helps with the latency.
fluxist said:
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
Click to expand...
Click to collapse
Impact on BT?
What a brill find. Well done.
Does it break anything with bluetooth?
Tx
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
if someone manages to get this working with xbox 360 make a tutorial plx ;D
superflysocal said:
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
Click to expand...
Click to collapse
thats what i wanna know , could i use my hsdpa connection via wifi to my psp?
I'll do a tutorial when i'm at home again. Maybe somebody with know-how can make a cab-file v1.0 for this "WLAN-Modem hack".
This surely will be a great app.
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
when you say click "IEEE 802.11b/g Compatible Wi-Fi" do you mean the wifi network adapters in my case would be "tiacxwln compatible wireless ethernet"? im trying it on a 6700 WM5
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
Got it - except on my device it's Programs -> accessories -> IS
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
Check - but is the T1ACXWLN1 device specific? If so, how can I find the interface ID on my device?
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
For me it's settings -> connections -> network cards, but I don't have an IEEE 802.11 listed. I connected to an existing AP, and found that my 'SDIO WLAN Wireless Adapter' does receive a DHCP address, so I tried changing it to 192.168.1.1...
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
Found this and set up my WING-FI network.
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
The client PC connects to WING-FI, but never receives an IP address...
What could I be doing wrong? Is it the hardware ID in the registry? I've created the network with WPA, then after the connection problems, with no security - but still no change.
Thanks!!
Ryan
neonstorm said:
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues...
Click to expand...
Click to collapse
Very likely the string TIACXWLN1 needs to be something different. Check HKLM\Software\WZCSV\Parameters\Interfaces\
There should be a key there with the name of your wireless adapter. It should end in "1".
And if not there, it should also be visible under HKLM\Comm\
Let us know how it works out.
EDIT: I just noticed you typed T1ACXWLN1. The string must be TIACXWLN1. That's "i" not one.
fluxist
I own a PPC6700 as well and I was able to get it working no problem other than the fact that our wireless adapter is not the same as the one mentioned. The reg edit is the same it's just the first network adapter in the list when you create the network settings.
fluxist said:
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
Click to expand...
Click to collapse
If you send me the dll I could look into it.
i have some experience with editing dlls.
good work man
So, as I look above, the question I have is to access my wireless at work, I need to have the ability to change the settings from OPEN to SHARED, or vice versa...
But as far as I can see, there's no option to do this? Or is there?
I have to say I am liking this device more and more every time I see it in action!
I am not entirely sure what you are asking for, but if you need to change the type of network that you would be connecting to, you can only do that at the router you cannot do it at the connecting device (in this case tablet).
If your work is using a WEP/WPA protected wireless network your tablet should have no trouble seeing it and connecting to it assuming you have the correct credentials.
Hey,
A friend of mine wants to lock the data connection of his 11 years old daughter's phone. So i thought, this would be easy, change the DNS as root to localhost or something like that. I read that it is possible to do so with the Wifi connection, but not permanent with the mobile data. This would just work for the current session, after a phone reboot, the normal mobile data DNS is back.
So my question is, what could i do, to lock every data connection? Is it possible?
Thanks for the answers!
why not just remove all apns and saved wi-fi networks? then there would be no mobile networks or wi-fi networks to connect to.
also, why does an 11 year old girl have an s2? if one isn't able to check on what their child is doing on the internet, and/or won't let them on the internet at all, might the s2 not be a little much?
This girl is not stupid, she knows how to connect to a Wifi network. Also it's thus a metter of time, till she knows to add the correct apn, or a friend of her does it.
I need a solution to realy change someting, that data is no longer possible. So she, or someone who knows a little bit about smartphones cannot enable it.
well that certainly is respectable, she knows how to crack wpa2 wi-fi keys?
then your dns trick, even if it were stored permanently, would be no use either.
i don't know, what country you are from, but at least here, every carrier offers the possibility to disable mobile data connections for your sim card. that way, no matter what you try to set up, the carrier would not accept you into their mobile network.
Could you delete APNs and wifi keys, then lock the settings app so the 11 year old cannot access it to edit the connection settings?
ZDBox is freeware and contains a reliable app locking tool.
Question: Is there a way to modify Android WiFi settings, even if rooting is required, such that the radio ignores all channels but one, say 165 in the 5ghz WiFi spectrum?
I know there is a way to limit the channels for a radio because this must be done for each country. I was just wondering if there is a way to augment the country specific settings by eliminating even more channels. The reason I would like to do this is to take an Android TV stick with Miracast Sink capability and limit the channels to one that is unused in my environment without relying on some sort of network negotiation. We have a wireless network that is quite dense and it seems to bog-down Miracast solutions. One like the Netgear PTV 3000 works fine at home but is really flakey at work. Also, the wireless network guys and security gurus don't like the idea of a wireless device that can't be tuned. This is just an attempt to remove one hurdle. Another hurdle would be to reduce the power setting of each radio but the channel selection is the most important.
Bryan