[Q] My vibrant will never charge ovet 96% on MIUI - Vibrant Q&A, Help & Troubleshooting

Yea, as the title says.
is there a way to fix this ?
THANKS!

I would try re-calibrating your battery. Try this which is straight from my MIUI guide.... (I suggest method 2 as it is the easiest)....
RECONDITION YOUR BATTERY
AFTER FLASHING IF YOU FIND THAT YOU HAVE BAD BATTERY LIFE TRY ONE OF THE METHODS BELOW TO FIX:
Method One:
Use phone till it dies on its own, completely dead.
Charge phone completely, plus 30 minutes longer.
Unplug phone from charger
Reconnect, you'll notice it's not full, charge till it is again.
This is bump charging and NOT something you want to do often, a few times is okay, in my opinion. You could skip the bump charge if you like.
Phone remains plugged in.
Boot into recovery (volumes + power)
Advanced > wipe battery stats, reboot.
Use phone till it's literally about to shut off (or does) Charge till full + Use phone like normal
OR
Method Two:
Download the Battery Calibration app by NeMa from the Android Market
Click to expand...
Click to collapse
Tell me if this works for you...

A real battery capped to charge at 96% or 97% due to voltage issues that would occur if charged to complete 100%. But samsungs stock ROMS and most other ROMS are customized to display this 100% when its really not at that level. Since MIUI is based off of CM7(and this is uncredited of course), it is not modified in any way and it displays the actual battery life. Which in your case is 96%. Hope this helps.
Sent from my SGH-T959 using xda premium

Related

[Q] Battery not at 100% after charging?

So I charge my Galaxy S2 to full (or at least, it says it's full), unplug it, and it says it's only charged to 60%, or 43%, or something random. I plug it back in, and off it goes, starts charging again, this time usually up to the "proper" 100%.
On top of this, the battery drain is very fast (10-15% overnight)
So, believing it's the battery, I get a replacement. Same thing.
I then learn that the reason might be because I flashed Lite'ning ROM while not on full battery, and that it just needs a battery calibration.
Ok, so I do a battery calibration - I charge it to full, drain it to 0%, then charge again. Take it off the charger, plug it back in to make sure it's full and...what do you know, the battery meter shows it at about 20% It continues to charge for about 4-6 hours after this.
Help? Is my phone faulty, or am I just not doing the calibration correct? I don't think it was like this before I installed Lite'ning ROM. So I'm praying it's not the phone itself?
The only other thing I can think that it might be, is the fact that it's a UK Galaxy S2, but I'm using it in Japan with a Japanese charger. Though I don't think that's an issue.
Any help would be very much appreciated.... not only does my battery not charge to full in one go, but it has **** life afterwards
did you try removig battery stats from recovery mode?
ProNewb said:
did you try removig battery stats from recovery mode?
Click to expand...
Click to collapse
Yeah, that's what I meant by "tried the battery calibration".
Charged to full, wiped battery stats from recovery, then rebooted.
Try using app battery monitor widget, and check battery is actually charging it to around 4200mV, and discharges to around 3500mV at approx 1%.
100% is not full, it will continue charging for quite a bit after to around 4200.
At least you will know that the high and low scale is correct, and can monitor in between.
Sent from my GT-I9100 using xda premium
So I charged it overnight via AC adapter (with the phone turned on), woke up, and the phone was at 4%!
Seriously, what the hell?
Phone was indeed reading close to 3500mV via Battery Monitor when it was almost empty
Any help?
Try charging via usb, much slower than ac though, then check again.
Don't drain battery to 0%, certain reports indicate not good for the battery, others say no worries. Try 1% so the phone doesn't turn off.
Although the huge jumps in battery level indicate a battery issue; If still no good, try a different ROM, and recalibrate. Also try in flight mode overnight and check results.
Sent from my GT-I9100 using xda premium
UpInTheAir said:
Try charging via usb, much slower than ac though, then check again.
Don't drain battery to 0%, certain reports indicate not good for the battery, others say no worries. Try 1% so the phone doesn't turn off.
Although the huge jumps in battery level indicate a battery issue; If still no good, try a different ROM, and recalibrate. Also try in flight mode overnight and check results.
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Thanks for the suggestions man, I appreciate it. My main concern is whether or not it is a problem with the phone itself - the place I bought it from has a ****ty returns policy and won't exchange it or anything. So I'm hoping like hell it is something I can fix myself (new battery, new charger, different rom, etc etc etc).
As I mentioned, I'm currently on the latest Lite'ning ROM with Ninphetamine kernal I believe. Just did a factory reset/data wipe via recovery mode, thinking it would get rid of lite'ning rom and the ninphetamine kernal, but upon rebooting the Lite'ning rom theme (blue lightning on the icons, etc) is still there.
Anyway, I have it charging on USB now, and I have ANOTHER battery coming tomorrow, along with a stand-alone wall charging unit (that charges just a battery on it's own, not connected to the phone). Maybe I should charge the new battery via that for 16 hours, then stick it in the phone, wipe the battery stats via recovery, and flash a new ROM (say, the new villainrom)?
Yeah, forgot about that also, I have two SGS2 (one in for repair), and each time new have let is charge overnight without turning on before first boot. Then discharge to approx 1% (do not let it die), then charge fully to 100% and approx 4200mV. Quickly clear battery stats with Battery Monitor Widget (menu / stats / SU permission, no need for recovery as you'll waste battery rebooting and get inaccurate reading) and immediately disconnect charging. A new batt stats file will be generated.
At least with this method you'll know your at a "true" 100%.
Also, it may take a number of charge cycles for full battery potential, but don't let it die.
I use Cognition straight "out of the box" with no issues.
Sent from my GT-I9100 using xda premium

[Q] Battery Charging

I am using CM7.1 Weekly #4 and i am unable to charge it to full 100%. the best i can get is 95% and it says battery full on lock screen. i don't know how battery percentage works in CM7, battery life is awesome so can any one help me how to get back to 100% charging like stock rom.
If you just flashed the rom then it could take a couple charge cycles for it to work itself out. Another "trick" I've read about is to:
1. Turn off the phone and take the battery out
2. Plug it in while the battery is still out and still turned off
3. Wait for it to display the "battery logo", it should have a question mark in it
4. Put the battery back in, still leaving it turned off, and wait for it to recognize the battery
5. At this point it might only show like 5% or 10% charge, don't worry about that, just let it sit on the charger for about 30 minutes to an hour while leaving it still turned off
6. After waiting, turn it on while plugged in and wait for it to boot and then unplug
From my understanding, this is a method to "bump charge" it.
Also, try using search next time instead of starting a new thread.
http://forum.xda-developers.com/showthread.php?t=1198333
xateeq said:
I am using CM7.1 Weekly #4 and i am unable to charge it to full 100%. the best i can get is 95% and it says battery full on lock screen. i don't know how battery percentage works in CM7, battery life is awesome so can any one help me how to get back to 100% charging like stock rom.
Click to expand...
Click to collapse
yes i am aware of that method, i think this method is only if ur facing bad battery. i am having gr8 battery just wrong percentages that's all.

[Q] Can't charge beyond X%. (Yes, I've searched!)(Yes, I saw Dianne Hackborn's post!)

Hopefully I can state this in a way that doesn't scream "I don't know how to use teh search!"
I calibrated my battery stats using the free app on the market after flashing darkside. My phone used to charge to 100% on the indicator (4200+ mV). Now, a couple of weeks later, it charges to the same 4200-and-up charge but the meter tops out at 92%. Two days ago, it was topping out at 94%.
I've re-calibrated using the app, draining it down and charging fully up. Same result, 92% max.
I've wiped battery stats using CWM immediately after charging fully (verifying the charge is above 4200 mV). Rebooted. Still at 92%. Actually, now it's reporting 90% with 4128 mV.
so if wiping stats is a "useless operation", what gives? How is it possible that this method apparently fixed other users' miscalibrated battery meters stuck down around 30-40%?
Try this:
1. Charge as much as it will charge
2. Turn it off and take out the battery
3. While the battery is still out, plug it in and wait for it to show the battery image with the question mark
4. Put the battery back in (do not turn on yet) and let it charge for an hour
5. After an hour, turn it on, unplug, and report back
Note: On step #4 when you put the battery back in it will probably only show like 5% or 10%, just ignore that and let it charge
cowsaregreat said:
Hopefully I can state this in a way that doesn't scream "I don't know how to use teh search!"
I calibrated my battery stats using the free app on the market after flashing darkside. My phone used to charge to 100% on the indicator (4200+ mV). Now, a couple of weeks later, it charges to the same 4200-and-up charge but the meter tops out at 92%. Two days ago, it was topping out at 94%.
I've re-calibrated using the app, draining it down and charging fully up. Same result, 92% max.
I've wiped battery stats using CWM immediately after charging fully (verifying the charge is above 4200 mV). Rebooted. Still at 92%. Actually, now it's reporting 90% with 4128 mV.
so if wiping stats is a "useless operation", what gives? How is it possible that this method apparently fixed other users' miscalibrated battery meters stuck down around 30-40%?
Click to expand...
Click to collapse
Bump charging now. Will report back in an hour
.... all right, got impatient. Pulled it just now; 99% on 4158 mV. That's better. Many thanks!
IT REALLY WORKS.........Thanks so much!
yes the above method Does work try it and it Will work for Ya
Sent from my MB860 using Tapatalk
in cm7, charges to 98% normally, but sometimes takes hours to reach 100%.
I hope i'm not hijacking this thread, but since we are talking about mV i thought this might be a good place to ask....
I've been having problems with my battery levels for a while, i've tried all the voodoo to try and fix it but i can't get anything consistent.
here is what i get....
i have battery calibration app installed, sometimes it will read 4200mV and be 20% charged. Other times it will read 100% charged at 3700mV, it's all over the place, and trying all the suggestions to fix the battery life don't seem to fix it.
another thing i have is it will discharge from 100% to 5% within an hour but my mV will be at 3900+, then it will sit at 5% for another 8+ hours then the phone shuts off, so i plug it in and it says 5%, i let it charge for a minute or two and it's at 20%, i turn it on and it shows that it's above 3700 or 3800mV.
so the phone thinks it needs 3700+ mV to run, but not always, sometimes it will go down below 3600mV and still run
A couple questions
1. can someone post their mV reading at 5%, i'm guessing it should be about 3300
2. what is the max mV that you have....is it above 4200mV (mine never is)
FYI information i've tried fastboot -w, cwm battery wipe, deleting the battery stats file manually, even formatted /system and other file systems to make sure it was fresh
live4nyy said:
Try this:
1. Charge as much as it will charge
2. Turn it off and take out the battery
3. While the battery is still out, plug it in and wait for it to show the battery image with the question mark
4. Put the battery back in (do not turn on yet) and let it charge for an hour
5. After an hour, turn it on, unplug, and report back
Note: On step #4 when you put the battery back in it will probably only show like 5% or 10%, just ignore that and let it charge
Click to expand...
Click to collapse
Ok,
I did this and my battery starts off at 100% and all appears to be fine. The next time I charge, it only shows 83% and it is reading 4200mV which should be a full charge. Do I have to do this each time? Is there any other solution? I am running CM7 stable and the battery is an aftermarket one. Could this be the issue? Thanks in advance all.
boulos said:
Ok,
I did this and my battery starts off at 100% and all appears to be fine. The next time I charge, it only shows 83% and it is reading 4200mV which should be a full charge. Do I have to do this each time? Is there any other solution? I am running CM7 stable and the battery is an aftermarket one. Could this be the issue? Thanks in advance all.
Click to expand...
Click to collapse
One trick I've found is unplugging the micro-USB and plugging it back in immediately. When I do this the 4200mV usually drops to the low 4100 range and the % continues to increase.
Only caveat is you'll have to keep doing this until it reaches 100. It takes a while since it seems to get re-stuck at every 1-2% intereval. A pain, but it's a work around from having to pull the battery. :silly:
I have the same issue too but DO I ALWAYS HAVE TO DO THIS METHODS? My battery level drops day by day (becomes %92 max) from %100.
I'd had the issues you explain for AGES.
I'd heard that buying a new battery wouldn't help. But I bought a new, official battery off eBay and I've not had the issue since. That was a couple of months ago now... not saying it will definitely work but at worst you have a spare battery...
What works for me... Charge up as much as possible, then use root explorer and go to data/battd/ and delete everything except the file "uid" then reboot... Should be good to go...
Hope this helps!
Sent from my MB860 using xda premium
bamastang said:
What works for me... Charge up as much as possible, then use root explorer and go to data/battd/ and delete everything except the file "uid" then reboot... Should be good to go...
Hope this helps!
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
This definitely worked for me. I was having repeated issues that full charge/drain calibrations didn't fix. This did.
I had the same issues with charging it ,but i foudn out that the only failproof method of chargin it by using the oem ac adapter and the oem usb cable if you dont have the cable the nokia cables shoud do the trick but the samsung one does not work i dnno exactly why but i tested it myself.
live4nyy said:
Try this:
1. Charge as much as it will charge
2. Turn it off and take out the battery
3. While the battery is still out, plug it in and wait for it to show the battery image with the question mark
4. Put the battery back in (do not turn on yet) and let it charge for an hour
5. After an hour, turn it on, unplug, and report back
Note: On step #4 when you put the battery back in it will probably only show like 5% or 10%, just ignore that and let it charge
Click to expand...
Click to collapse
what do you mean of the 3 step, do you mean while the battery out, plug it to AC and wait ? mine doesnt do anything...I dont think any phone works without a battery.
shevin said:
what do you mean of the 3 step, do you mean while the battery out, plug it to AC and wait ?
Click to expand...
Click to collapse
Yes, that's what the step 3 means.
shevin said:
I dont think any phone works without a battery.
Click to expand...
Click to collapse
You'd be surprised.
ravilov said:
You'd be surprised.
Click to expand...
Click to collapse
Ha, I remember my old startac worked like a charm plugged in the charger without a battery xD
Enviado desde mi MB860 usando Tapatalk 2

[Q] Battery is burning FAST !

First of all it wouldnt charge past 99%, And then, after one hour of standby it went down to 88%!!
Cm7 official stable release.
Me too no pass 99% :S
Try to download a "battery caliberation" app and do that, also burn it to 0% and charge to 100% while the phone is off..i heard that this might help.
Now i will flash Nottachtrix and do what i wrote Good luck man !
Velcis Ribeiro said:
Me too no pass 99% :S
Click to expand...
Click to collapse
The charging thing is something that is (seemingly) well known throughout the community. I have tried to do the calibration, but it doesn't seem to work that well (at least for me). There is a thread around here somewhere for fixing the issue. I just have never tried it due to work reasons.
The charging past 99% is a known issue with most of the ROMs. There is a thread in here that takes you step by step to get it to display 100%. Basically....
Charge the phone long enough to where you know it should be at 100% even though it is still displaying 99%.
Power the phone off while it is still connected to the charger and then pull the battery.
With the battery pulled, power the phone back on until you see the battery indicator with the "?".
Put the battery back in and reboot.
You will then see the display of 100% with the phone still connected to the charger. The only downside is that as soon as you disconnect the charger, it will drop back to 99%. I have done this multiple times.
You can try the latest nightly: update-cm-7-20120508-NIGHTLY-olympus-signed.zip
I read good things about it.
First of all, use Wipe Battery Stats function at recovery.
1 - Discharge all your smartphone battery;
2 - Connect it to the wall charger and don't turn it on;
3 - Wait till it shows you 100%;
4 - Remove the battery, wait 10 seconds, put it again and keep it turned off;
5 - Wait 30 minutes, keep it connected to the wall charger and press power button till it turns on;
6 - Wait 30 minutes, keep it connected to the wall charger and use Battery Calibration App to calibrate it;
It doesn't make any sense, but sometimes, after step 5, i prefer connect it to usb port in a laptop or computer and wait one hour. It always worked with me.
It might solve your problem .
Wiping battery stats does nothing. it just takes a few charge cycles. If it's a new rom and it's draining fast it's also cause you are probably playing with it a lot
Sent from my Galaxy Nexus using Tapatalk 2
nathan96 said:
after one hour of standby it went down to 88%!!
Click to expand...
Click to collapse
It could be a bluesleep problem... Install CPU Spy App and look if it goes into deep sleep mode. If not, there is a fix for it.
Aside from the OP's issue with the battery draining quickly, why does it matter if it doesn't show 100%?
Nothing can ever 'really' be 100% charged because as soon as you take it off mains it is instantly on the battery at lets say 99.9999%...
As long as the battery doesn't drain quickly I couldn't care less if its showing 99 or 100%.
The problem was that it was draining very quickly to smt like 50% and then it would hold longer...I just wiped everything, restored a neutrino 2.7 nandroid backup i had, flashed the jug fix v2 and now it shows 100%

Rom/Battery

Having issues with roms lately. Some roms won't even give me 2 hours of battery life. (Maybe 4 hours even in standby!!)
Talked to Motorola over the phone they think maybe it's the battery, they sent me a free one but I still have the same issues.
Sometimes I look at my phone and it has already been drained. Then I see that standby has taken up 75% of the battery. Like wtf lol.
So the question is, what is the best ROM for battery life?
Thanks.
Neutrino v2.9
Make sure you install bluesleep fix if the rom you are using doesn't have it....
For me the best results have: "old" ALIEN and CM7 !!!
CM7 - 1day and 27minutes with 7hours and 28minutes screen on (30-35% luminoziti)
Sorry for english!
Atrix - "CM7"
Seeing as it happens with every ROM, you may try to calibrate your battery, it may help. Download 'Battery Calibration' app from the Play Store and follow the in-app instructions. I always calibrate mine after changing ROMs exactly because problems like yours happened to me in the past.
MaxK47 said:
Seeing as it happens with every ROM, you may try to calibrate your battery, it may help. Download 'Battery Calibration' app from the Play Store and follow the in-app instructions. I always calibrate mine after changing ROMs exactly because problems like yours happened to me in the past.
Click to expand...
Click to collapse
That app does not calibrate the battery. All it does reset the previous battery usage graphic table.
Sent from my MB860 on CM10 (Epinter)
Soldier-2Point0 said:
That app does not calibrate the battery. All it does reset the previous battery usage graphic table.
Sent from my MB860 on CM10 (Epinter)
Click to expand...
Click to collapse
But it helps. If I don't do it, after 2~3 flashes of different ROMs I start to have huge drops (staying at ~80% for 6 hours, then instantly dropping to 20%) or the system misreads the actual battery capacity (turning off with at least 30% battery remaining, for example).
Have you tried wiping battery stats?...
Charge the phone as far as it will go (lets say over night)(also if you need to plug the phone into the charger after it has charged over night without the battery in it so you get he battery with a question mark, then put the battery in and it should show like 5% battery or something then let that charge as long as it will, which is usually around 15% if i remember correctly), then wipe battery stats in cwm or whatever way you prefer. Reboot the phone and use it until it is completely dead (0% battery and the phone shuts itself off and wont turn back on, but do not try to drain the battery using video loops or anything, just use it like you normally do. Then charge it up to 100% but do not turn it on, let it stay on the charging screen until it gets to 100% and dont use or unplug it at all. It should take longer to get from 99% to 100%, just be patient Hopefully that solves the issue.

Categories

Resources