bootloop after rooting, no other ROM - Galaxy Tab 10.1 Q&A, Help & Troubleshooting

I followed the directions to root on the LOOK HERE FIRST, so I installed Clockwork, then flashed the root zip, and that's it - I never installed any other ROM. It seems to operate just fine, but then at some point when I reboot it gets stuck at the Samsung logo. I repeatedly restore my NAND backup from before I rooted, flash the root zip again (and I tried redownloading it, in case it was corrupted), and try rebooting and it boots just fine. But then it always breaks itself and boot loops again after a while. I've done this a couple times.
I have the Wifi only tab 10.1 7510 (U.S.).

I suggest following this guide, step by step. It never fails.
This one will get you back to a fresh start.
http://galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-unroot-your-galaxy-tab-10-1/
And this one will get you rooted properly.
http://galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
After that, just make sure to do a nandroid/Titanium Backup before wiping Cache, Dalvik Cache, and then data, all before installing a new ROM.
And after you do the 3x wipe, don't boot up at all. Just install straight from recovery.

kehlan said:
I suggest following this guide, step by step. It never fails.
This one will get you back to a fresh start.
http://galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-unroot-your-galaxy-tab-10-1/
And this one will get you rooted properly.
http://galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-unroot-your-galaxy-tab-10-1/
After that, just make sure to do a nandroid/Titanium Backup before wiping Cache, Dalvik Cache, and then data, all before installing a new ROM.
And after you do the 3x wipe, don't boot up at all. Just install straight from recovery.
Click to expand...
Click to collapse
Those are both the same link, I'm guessing a mistake? I would be interested in the better root tutorial.
This last attempt seems to be working so far. I systematically restored/redid things and tried rebooting to try to rule out possibilities. The one thing I did differently this time is that I installed Busy Box to /bin instead of /xbin (Titanium Backup restore hangs without Busy Box). Go figure.

Earned yourself a thanks by pointing out my mistake.
Updating that post momentarily.
Edit: Updated, best of luck getting everything working.

kehlan said:
Earned yourself a thanks by pointing out my mistake.
Updating that post momentarily.
Edit: Updated, best of luck getting everything working.
Click to expand...
Click to collapse
I think it would be better if you updated the post permanently. Seems silly to just do it momentarily.

I meant I was going to update it momentarily from the point I had noticed it was wrong.
It's been correct since then, hope everything worked out.

Related

How I fixed my phone

So i'm going to consolidate and give everyone a brief recap on how I fixed my phone since it required the use of SEVERAL posts. I figured someone will eventually get caught in the same situation I was.
This is by no means the best way, or the correct way to fix any phone, do this at your own pace and liability. I am, and no one mentioned in this thread is liable for your phone.
Please excuse any of my grammar mistakes, this is spewing out as I type.
History: Stock DI01 update w/ JT's Voodoo .2 OC Kernel.
Flashed JT's Super Clean ROM V.4 & Remix Incognito Theme.
** Market would no longer work. I had this issue before updating to the 2.2 market after the DI01 update, so I uninstalled and worked again, however, that option wasn't available with the ROM Flash.
I couldn't find a single fix that would work to get the market to work, even ADB pushing older market apk's to the system wouldn't fix it. I decided to do a flash of JT's Super Clean ROM V.2, that didn't fix the issue either.
**I was clearing data and wiping dalvik after each flash**
With nothing seeming to work, I decided to try Deodexe's Zinc ROM, and this is where **** hit the fan. After doing this, I sent my phone into FC boot loop hell. I was getting the process.acore FC everytime I pressed a key. I rebooted back into Clockwork, tried to recover from an old ROM I had backed up the previous day, notta. Damage was done. I was getting FC bootloop hell with a very crappy performance.
I decided it was time to Odin restore and start over. These aren't the exact steps I took, but if I had to do it over again, this is how I would do it. If at any point you're getting a process.media FC, remove your SD Card, and leave it out until you need it for CWM.
STEP ONE:
If you installed Voodoo (at any point, removed or not, do this step)
Thanks to adrynalyne
http://forum.xda-developers.com/showthread.php?t=804784
This was the main culprit behind my phone not working correctly after a complete restore. I moved this to the top of the list, because after that, it's downhill.
STEP TWO:
Completely Restore with Odin Restore Files
Thanks to fallingup
http://forum.xda-developers.com/showthread.php?t=782204
The instructions are a little un-clear, but do this. First, Only use the PDA option, and flash each backup one at a time along with the PIT file. You're not out of the clear yet. Read on.
STEP THREE:
Flash CWM Recovery (read my notes below)
Thanks to fallingup
http://forum.xda-developers.com/showthread.php?t=788099
After you've flashed CWM. Boot into CWM Recovery, Boot back in Stock Recovery and wipe data and cache. Boot back to CWM (select sd:update.zip) and do the exact same thing there. Reboot phone.
STEP FOUR:
Do a data factory reset
Even though you have just restored the **** out of your phone, you're still not there. Get through all the account setup fields and go to Settings > Privacy > Factory Data Reset.
After a reboot, you should be on your way to a completely 100% stock fixed phone. At this point, I would suggest making a ROM back up of this point before moving ahead with flashing again.
LAST STEP (for me anyway):
Restore apps via Titanium Backup
This restored most my apps and settings that I had already saved, including LauncherPro and the backups I had for that. If you haven't used Ti, then use whatever app backup app you do have, if you do indeed have one.
I decided to re-flash JT's Super Clean ROM V.4 found here. Thanks to JT
http://forum.xda-developers.com/showthread.php?t=796171
I am also running the Remix Incognito Theme here: Thanks to frostman89
http://forum.xda-developers.com/showthread.php?t=801867
Right now I'm mixed on updating a new Voodoo Kernel, I haven't decided if I want to do that again or wait for something else.
Thanks again for all the DEV support, hopefully someone searching will find this thread useful.
Pretty much my standard routine when trying new kernels.
I have a nandroid with my basic rooted setup (apps and data intact), so this doesn't set me back by a huge amount.
Just a few differences...
I use:
Odin (System, then kernel) (step only needed if things are *really* messed up...won't boot)
Boot into Recovery
flash update.zip to get into CWM
Wipe Data/Cache/Davlik
Reboot into recovery
run jt's voodoo_uninstall (flashes stock.zip and replaces mbr with stock mbr)
reboot into recovery
restore nandroid image.
This has yet to fail me and usually takes under 10 minutes. The nandroid image is key. Most of the time, I can skip the Odin step completely if I am not seeing anything truly, staggeringly horrific going on.
Again, jt's voodoo-uninstall seems to solve a lot more than just voodoo issues. This thing should get it's own topic/forum/entry in ROM Manager/zip code/nobel award...you get the picture.
PhoenixPath said:
Again, jt's voodoo-uninstall seems to solve a lot more than just voodoo issues. This thing should get it's own topic/forum/entry in ROM Manager/zip code/nobel award...you get the picture.
Click to expand...
Click to collapse
+1 I agree
Nice write up! I'm sure this will help many people.
Thanks
This along with several other threads allowed me to recover from my own mental retardation.
Gotta remember to remove voodoo before doing stuff. I should know better.
Thanks again.
This is not working for me. I removed voodoo (using the uninstaller). I then did odin and my phone boots but I cant do anything past the unlock bc of all the fcs I get. I wiped the cache and data. CWM is not working, when I try to do the update.zip I get a "failed to verify whole-file signiture". - I deleted the voodoo folder from the sd-card after uninstalling voodoo, dont know if that contributed to the problem. Any ideas?
Ke1evraTi said:
This is not working for me. I removed voodoo (using the uninstaller). I then did odin and my phone boots but I cant do anything past the unlock bc of all the fcs I get. I wiped the cache and data. CWM is not working, when I try to do the update.zip I get a "failed to verify whole-file signiture". - I deleted the voodoo folder from the sd-card after uninstalling voodoo, dont know if that contributed to the problem. Any ideas?
Click to expand...
Click to collapse
Sounds like you need to re-flash ClockworkMod through Odin. I'm guessing it got wiped out when you went back to stock.

[Q] Problem Installing New Vegan Ginger

OK i have to say i m not a noob anymore. And i m pretty confident.
Having said I am coming from Vegan 5.1 and tried many times to download the new Vegan Ginger. But each time I got stuck at the "birds" screen.
And yea I do all the same steps for when i was ROMing to Vegan 5.1
So my questions are: why isn't it working this time?
Do i have to be on Stock Rom for it to work?
Any suggestion?
Thank you
Its always a good idea to start from stock and then going to custom rom. I suggest you use nvFlash to go back to stock, then flash cwm .8 and then try to follow your steps to install it.
enjoy
Best way to flash a new rom is to fully wipe data cache dalvik ect ect do that in cwm then install zip from disk. Works every time and usely it take like ten minites to fully install. If you need help just look around or ask.
Good luck
Awessssoooommmee
You guys are awesome
I just Nvflash and Install the ginger edition easily
Thank youuuuu
I'm having the exact same problem. Even fully wipe data, cache and davik does not help.
I noticed that, when ClockworkMod Recovery showed that it was installing update, the progress bar stayed grey, not changing or moving at all.
Guess I'll have to try nvflash.
Yeah do that
ww9rivers said:
I'm having the exact same problem. Even fully wipe data, cache and davik does not help.
I noticed that, when ClockworkMod Recovery showed that it was installing update, the progress bar stayed grey, not changing or moving at all.
Guess I'll have to try nvflash.
Click to expand...
Click to collapse
Yea do that, cause it looks like this ONLY works on stock rom. And after that just do your usual process, and you should be good.
Everything went so well that my first boot took less than a minute

Need help with booting

hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
PLEASE CLOSE
did you not wipe system and data? I am not super skilled, but maybe it tried to stick the entire ROM into the left over space of the last ROM that is still on there?
It won't boot to recovery? It should boot to recovery
weezymagic said:
hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
Click to expand...
Click to collapse
The error message you received is going to be the key to understanding the issue that occured. When it says unmounted, it is referring to a specific partition, either /data or /system most likely.
For starters, when it hangs on the htc white screen, this is usually either a kernel or ramdisk issue. If the kernel is known to be good, then it is probably a ramdisk issue. most ramdisk issues relate to a mismatch/incompatibility between the loaded kernel and the ROM.
First suggestion would be to reflash the ROM, clearing /cache and /data.
Second suggestion would be to restore a backup. This will confirm there is nothing wrong with your device hardware wise and you'll know it is a specific issue with the ROM you wanted to load.
Third suggestion, find the exact error, word for word, which occured in recovery and post up in the ROM thread asking if other users of that ROM also encountered, how they handled. Also feel free to post back up here.
When writing the programming behind a custom recovery, the error messages are added in there to help allow users and developers better knowledge of the exact issue so they can work to resolve them. Without the exact error message, it is similar to going to a car shop and saying, some light came on my dash, but I don't know what it was and now the car doesn't work. Fix it? Another words, it is very vague.
Hope the suggestions and tips help! Good luck!
my first instinct was to reflash the backup or new rom again but it wont boot to any rom, recovery or bootloader. it just hangs on the htc white screen
idk what happened but i got into the bootloader through battery pull, power+vol down. i know ive tried that in the past but this time it worked. now im restoring a nandroid from yesterday
weezymagic said:
idk what happened but i got into the bootloader through battery pull, power+vol down. i know ive tried that in the past but this time it worked. now im restoring a nandroid from yesterday
Click to expand...
Click to collapse
are you on twrp 1.0.x ? There is s charging issue where it won't restart right because it thinks It's already in recovery
sent from my EVO 3D via XDA app
weezymagic said:
hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
PLEASE CLOSE
Click to expand...
Click to collapse
You missed a step. After you wipe dalvik and cache, you ALWAYS need to wipe /system and /data, do a factory reset to make sure, or download a superwipe tool. The ONLY time you don't need to wipe completely is when you're updating your ROM, but even then it is recommended to wipe everything.
Twolazyg said:
You missed a step. After you wipe dalvik and cache, you ALWAYS need to wipe /system and /data, do a factory reset to make sure, or download a superwipe tool. The ONLY time you don't need to wipe completely is when you're updating your ROM, but even then it is recommended to wipe everything.
Click to expand...
Click to collapse
Agreed^^^^^

[Q] Help Getting A Working Rom after Bootloader Unlock

Hi all,
I have a Droid incredible 4g (stock, unrooted/unlocked, w/ the recent OTA update). I saw the Bootloader Unlock exploit in the developer's forum so I gave it a go, and it worked fine. Then I installed the Viper 1.0 ROM, but I haven't been able to get it to do anything after successfully booting except run through a loop of errors such as "Unfortunately, the process android.process.acore has stopped working." After I click "OK" on about 10 critical errors, it self-reboots and does the whole thing again.
Unfortunately, I didn't do a backup this time, so I have nothing to restore (first time I haven't done a backup, but also the first time I've ever had any kind of an issue w/ a ROM). I tried using the HTC Android ROM Update Utility 1.0.5.2011 that I found in the dev forum, but that didn't work either. Finally, I installed 2.17.605.2 Verizon Global Sense4.1 Android 4.0.4. It's a lot more stable than Viper was and the phone is basically usable, but I still get lots of critical errors. So this morning I went back to the forum and saw that I needed to downgrade to the old 1.43.605.3 kernel. I tried that and then reinstalled Viper 1.0, but it seemed to have no effect--still stuck in a critical error/reboot loop.
I realize that's the risk of playing with ROMs and I should have done a backup, but anyone have any ideas on how I can get my phone back and running?
Thanks!
Even though it explicitly stated you didn't need to do a backup, I did one anyway, to prevent something like this from happening. Always do a backup.
Did you verify the MD5Sum of ViperLTE?
Did you go to Recovery and Wipe -> Factory Reset and Wipe -> System both twice before trying to install the ROM?
Did you change anything in the ROM before attempting to load it?
There are lots of questions we could ask to ascertain the root of the problem, but these three are among the most important.
Wi-Fi won't work without the old boot.img, and from what I can tell, that's the only thing. It doesn't give critical errors.
I'm thinking since you are new to root you were un-aware the need to wipe before installing a rom.
im thinking that is the issue.
Thanks for the reply!
I didn't check the MD5 last night but I did just now and it matches.
I did a cache wipe the first time but not a system wipe. Then I started getting more desperate and tried reinstalling w/ system wipes and factory resets, but it didn't change anything.
No, I didn't change the ROM. Doing the Bootloader unlock exploit was about the absolute maximum of my technical abilities! The only thing I know I did wrong was that I didn't downgrade to the old boot version the first time (mainly because the wifi thing sounded inconsequential and I didn't want to learn the procedure if I didn't have to).
Anyway, I just tried Ultimate KangBang and it seems to work--no error messages so far. I don't know what I did wrong, but hopefully this keeps working!
IceDragon59 said:
Even though it explicitly stated you didn't need to do a backup, I did one anyway, to prevent something like this from happening. Always do a backup.
Did you verify the MD5Sum of ViperLTE?
Did you go to Recovery and Wipe -> Factory Reset and Wipe -> System both twice before trying to install the ROM?
Did you change anything in the ROM before attempting to load it?
There are lots of questions we could ask to ascertain the root of the problem, but these three are among the most important.
Wi-Fi won't work without the old boot.img, and from what I can tell, that's the only thing. It doesn't give critical errors.
Click to expand...
Click to collapse
andybones said:
I'm thinking since you are new to root you were un-aware the need to wipe before installing a rom.
im thinking that is the issue.
Click to expand...
Click to collapse
Yes, I took a short-cut that didn't quite work out. I didn't want to wipe the system because I wasn't sure if my pictures would be wiped too, but then when everything died I tried wiping everything and reinstalling and it didn't seem to improve anything. I did end up losing my pictures too. Oh well. Maybe it's just a combination of stuff I did to try to get things working (there was some trial and error in unlocking the bootloader but I did get that to work finally, and then more trial and error with the ROMs).
I guess the best thing to do is leave the phone the heck alone as long as it's working, for now. I just don't know why nothing seemed to work--I thought factory reset/fresh ROM would do it.
franklin411 said:
Yes, I took a short-cut that didn't quite work out. I didn't want to wipe the system because I wasn't sure if my pictures would be wiped too, but then when everything died I tried wiping everything and reinstalling and it didn't seem to improve anything. I did end up losing my pictures too. Oh well. Maybe it's just a combination of stuff I did to try to get things working (there was some trial and error in unlocking the bootloader but I did get that to work finally, and then more trial and error with the ROMs).
I guess the best thing to do is leave the phone the heck alone as long as it's working, for now. I just don't know why nothing seemed to work--I thought factory reset/fresh ROM would do it.
Click to expand...
Click to collapse
If UKB ROM works then Viper ROM will too, installing the boot.img is very simple it's one command
I can help you with that if you'd like
in recovery before installing ROM, do a wipe of, (I go in this order, but it doesn't matter.)
1) Factory Reset
2) System
3) Cache
4) Dalvik Cache
then install the ROM
just DO NOT do External storage (unless of coarse u WANT to wipe your SD-Card.)
as long as you don't wipe External Storage you won't lose anything that's on your SD-Card.
in the future it is always good practice to backup(nandroid) your current ROM. I have been burned too many times, always do a nandroid before you do anything in recovery.
your photos are normally saved to the SD, flashing ROMs or wiping the system will not delete them
andybones said:
If UKB ROM works then Viper ROM will too, installing the boot.img is very simple it's one command
I can help you with that if you'd like
in recovery before installing ROM, do a wipe of, (I go in this order, but it doesn't matter.)
1) Factory Reset
2) System
3) Cache
4) Dalvik Cache
then install the ROM
just DO NOT do External storage (unless of coarse u WANT to wipe your SD-Card.)
as long as you don't wipe External Storage you won't lose anything that's on your SD-Card.
Click to expand...
Click to collapse
It worked this time! Maybe the difference was that the boot.img file I downloaded was called "boot_signed.img" or something. I had no idea what it was supposed to look like, so I installed it that way and it didn't work. Then I tried renaming it to "boot.img" this morning and installing viper, but that didn't work. And then I restarted and installed UKB, and it worked. Just now I wiped and tried again with Viper and it's working fine. Maybe I did something this morning that caused it not to take properly when I tried with Viper, and then I reset and it worked.
Thanks for the help!
franklin411 said:
It worked this time! Maybe the difference was that the boot.img file I downloaded was called "boot_signed.img" or something. I had no idea what it was supposed to look like, so I installed it that way and it didn't work. Then I tried renaming it to "boot.img" this morning and installing viper, but that didn't work. And then I restarted and installed UKB, and it worked. Just now I wiped and tried again with Viper and it's working fine. Maybe I did something this morning that caused it not to take properly when I tried with Viper, and then I reset and it worked.
Thanks for the help!
Click to expand...
Click to collapse
na the name has nothing to do with it. it can be named whatever.
im guessing the wipe worked.
franklin411 said:
Hi all,
I have a Droid incredible 4g (stock, unrooted/unlocked, w/ the recent OTA update). I saw the Bootloader Unlock exploit in the developer's forum so I gave it a go, and it worked fine. Then I installed the Viper 1.0 ROM, but I haven't been able to get it to do anything after successfully booting except run through a loop of errors such as "Unfortunately, the process android.process.acore has stopped working." After I click "OK" on about 10 critical errors, it self-reboots and does the whole thing again.
Unfortunately, I didn't do a backup this time, so I have nothing to restore (first time I haven't done a backup, but also the first time I've ever had any kind of an issue w/ a ROM). I tried using the HTC Android ROM Update Utility 1.0.5.2011 that I found in the dev forum, but that didn't work either. Finally, I installed 2.17.605.2 Verizon Global Sense4.1 Android 4.0.4. It's a lot more stable than Viper was and the phone is basically usable, but I still get lots of critical errors. So this morning I went back to the forum and saw that I needed to downgrade to the old 1.43.605.3 kernel. I tried that and then reinstalled Viper 1.0, but it seemed to have no effect--still stuck in a critical error/reboot loop.
I realize that's the risk of playing with ROMs and I should have done a backup, but anyone have any ideas on how I can get my phone back and running?
Thanks!
Click to expand...
Click to collapse
weird, i was having the same problem with the same processes stopped working. i wiped cache dalvik and system but not factory reset. once i factory reset, it worked fine. i figured a system wipe would have been enough....

Help me undo my stupid mistakes! (Bootlooping)

Hi everyone,
I would like to preface with I made some very stupid mistakes late last night/early this morning. I decided at around 11pm I was going to root and install a custom recovery on my SGP311. I followed this guide exactly to obtain root and recovery and it worked PERFECTLY.
http://forum.xda-developers.com/xperia-tablet-z/development/root-sp321-ftf-10-5-1-0-283-t2873377
Then the mistakes started happening. First mistake I made.
1) Instead of backing up everything in recovery I just Wiped everything. I deleted cache, davlik cache, system, and data. I thought at the time no big deal ill just flash a rom.
2)I decided to flash a CM nightly and I got the "your device is a pollux and this rom is for pollux_windy" error and assumed I was wrong. I downloaded the pollux version, and flashed it. That was the dumbest thing I did. I booted and immediately started looping at the cyanogenmod screen.
3) I attempted to troubleshoot by flashing firmware and kernels through Flashboot. It made it worse and now I cant get into recovery at all.
Here is the positives
I can connect to the device through Flashmode and Fastboot.
What should I do next to remedy this situation?
TheShackSpecialist said:
Hi everyone,
I would like to preface with I made some very stupid mistakes late last night/early this morning. I decided at around 11pm I was going to root and install a custom recovery on my SGP311. I followed this guide exactly to obtain root and recovery and it worked PERFECTLY.
http://forum.xda-developers.com/xperia-tablet-z/development/root-sp321-ftf-10-5-1-0-283-t2873377
Then the mistakes started happening. First mistake I made.
1) Instead of backing up everything in recovery I just Wiped everything. I deleted cache, davlik cache, system, and data. I thought at the time no big deal ill just flash a rom.
2)I decided to flash a CM nightly and I got the "your device is a pollux and this rom is for pollux_windy" error and assumed I was wrong. I downloaded the pollux version, and flashed it. That was the dumbest thing I did. I booted and immediately started looping at the cyanogenmod screen.
3) I attempted to troubleshoot by flashing firmware and kernels through Flashboot. It made it worse and now I cant get into recovery at all.
Here is the positives
I can connect to the device through Flashmode and Fastboot.
What should I do next to remedy this situation?
Click to expand...
Click to collapse
I just quickly read your post from work but since you wiped it and can no longer boot your tablet...just flash back a stock FTF with FlashTool and your tablet will back to full stock...you'll have to re-root obviously. Hope this helped... :good:
Crash338 said:
I just quickly read your post from work but since you wiped it and can no longer boot your tablet...just flash back a stock FTF with FlashTool and your tablet will back to full stock...you'll have to re-root obviously. Hope this helped... :good:
Click to expand...
Click to collapse
I'm downloading the FTF right now, Ill let you know how I make out so that people can see the resolution!
*EDIT* IT WORKED!!!! I missed the simple solution because I am so tired right now. But my tablet is working which is the important part THANK YOU!!!!

Categories

Resources