Related
My xda's aerial came off in my hand the other day, while I was removing the stylus. I thought I'd fixed it back on, but I can't get a phone signal now (I live in a good reception area).
Anybody know how to fix these? There only seems to be one loose part inside (a small spring).
Thanks in advance
Ian.
I managed to break mine also, can you send me a picture of what you found under the black plastic cap? the address is [email protected].
Thanks
Hi !
Please send me foto also.
[email protected]
THX
You should have a small conical spring attached to the circular brass post under the plastic aerial/stylus appatuture cover (thin end up!)
Rick,
Thanks, that's what I have - I was worried that something else had popped out. I'm now led to believe that the spring is the aerial? Hi-tech components....
A secondary question. As the black plastic cover has worked loose, I plan to super-glue it to the body. Anyone think this is a bad idea?
Ian.
I had the same problem with mine and also lost the spring. A cut down spring from a biro worked quite well till I had a chance to get it repaired on warranty
Antenna super glue
SuperGlue seems the only way to
make sure it doesn't come off again.
Best regards,
Murk
Hi, is there any chance to get Topaz disassembly guide?
THX
Edit: Dont need it anymore, I have done it, not difficult at all (similar to Nokia phones). HTC made Topaz very easy to disassembly.
I was cleaning part between digitizer and LCD from dust with antistaic brush and compressed air.
There are just 3 connectors to disconnect mainboard (digitizer, phone receiver and LCD), to get to the LCD. No coaxial cables to connect GPS and bluetooth antenna (all just by touch connectors to the black plastic top back part), Chipset is covered by metal plate, cant see it.
LCD: S/N: 1EJV093Q000069
P/N: 60H00209-00M S508
Can I request you get some high res photos of the PCB/LCD and/or record the ic part numbers while you've got it apart? It would be really useful to know for Linux/Android development.
Can you post what kind of gps chipset is buildin ?
Thanks in advance
Daniel
Thanks for the photos! Would you be able to post a higher res version of the 3rd one or simply scribe what is written on the back of the LCD. I'm hoping the serial number might give an indication of the chipset used in the LCD.
cheers!tsy
So you can sure tell us if the front frame is really metal or plastic ?
Its metal body iside of plastic housing.
Great job !
Thanx
some instructions or tips of how you disassembled it would be nice
i unscrewed my diamond2, and i cannot find a way to disassemble it..
help!
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
i found a htc service manual for diamond 2 that was leaked
not sure if i can post it here..
it explains how to disassemble the device
EDIT: I am so sorry, the leaked document is the user manual, it is incorrectly posted as the service manual in many sites. sorry
post it! what's the worst they can do... tell you to remove it?
PhilipL said:
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
Click to expand...
Click to collapse
Look here:
http://forum.xda-developers.com/showthread.php?t=520795&highlight=solution%21%21%21
Sticky? New Thread? & Help
I think we either need to sticky this, or make a new thread that encompasses all disassembly / dust leak information about the topaz.
I still cannot disassemble my device, i wish someone could help :/
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Guinea.Pig said:
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Click to expand...
Click to collapse
Thanks for the steps. I just yesterday disassembled my TD2, but didn't dare remove the connections on the mainboard. The one on top left (see your pic mainboard.jpg) is no issue, but the other ones are tricky...or at least I thought they are. I couldn't figure out how to exactly remove those connectors. Could you maybe give some steps or info on how to remove those connectors? Thanks again for your help.
disassembly
thanks for the update . ill try and post pictures up when possible.
I am interested in this too, I have dropped mine a couple of times and am looking to replace the housing (although I have already been ripped off once by buying a repaired one on ebay).
So any idea where I can get a legitimate full housing and a guide to moving the guts from one to another?
Cheers,
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Awesome
stormyuk said:
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Click to expand...
Click to collapse
Thanks for your contribution stormyuk !
You can find housings on ebay, though most don't come with the buttons.
I bought one and its practically impossible to distinguish any differences,
Buy from kr-net on ebay its the seller that sold me my housing
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Brando ships worldwide and is pretty reliable. Why not use them?
On ebay.com I found some offers as well, some for about 33USD, like half price as from Brando Shop...
How to Dismantle
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Scary Procedure
Hello! My touch screen is scratched and I bought another one to replace it. Well, it isn't so easy and after I dismantled the device, I decided not to replace it and wait for some tips because no documentation exists. No manual included with the package and no info on the net. (there are some youtube videos for other phones)
After you open the device, you end up with your phone in 3 parts. The Touch screen has a black marquee surrounding it witch I don't know how to remove, and it is connected with the main board with a very very thin wire witch I'm afraid to pull and I'm not sure if I have to pull it or do something else to remove it from the main board. Tips are welcome. Thank you!
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
yianp said:
Hello! My touch screen is scratched and I bought another one to replace it.
Click to expand...
Click to collapse
where did you find the replacement?
Marcell-o said:
where did you find the replacement?
Click to expand...
Click to collapse
I bought one from ebay. Unfortunately no instructions with the package
Kajmaj said:
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
Click to expand...
Click to collapse
Hey Kajmaj THANK YOU SO MUCH!!!!
yianp said:
I bought one from ebay. Unfortunately no instructions with the package
Click to expand...
Click to collapse
i've tried to open the device.
It's not so hard:
AT OWN RISC!!!
Unscrew the 4 screws, click it slightly open.
now you can see on 1 side a small flatcable for the digitizer, unlock it by swapping the behind of the connector. Unplug it.
Flip the PCB and unplug the 2 connectors for the screen and buttons.
Now you can unscrew 2 litle screws at the buttons.
remove the buttons carefully.
Now you can slightly press on the back of the old digitizer untill it loosses.
Place the new one, carefully press on the glue-parts untill you think it is tight enough.
Now read this post backwards to put it all together again.
If you're ready, push the on button.
When it asks for the pincode press : volume up + centerbutton to calibrate.
Et voila.
AT OWN RISC!!!
i'm not responsible for any damage.
Scratched external screen
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
yianp said:
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
Click to expand...
Click to collapse
You can leave it there.
You have to push at the back of the digitizer.
it's verry tight glued so you have to be patient and careful that you do not break the housing.
The rubber you talk about is meant to leave dust out of there.
i placed my new one just now and it works great.
I made some pictures of the repair and i'll post them tomorrow if i don't forget.
Pictures of the repair
Here are some pictures with some info.
And again:
AT YOURE OWN RISC, I'M NOT RESPONSIBLE FOR ANY DAMAGE!!
before the repair it was like this.
As you can see, it was in a very bad shape.
you can see what i use the most.
The "X" at the upper right corner and the IE scrollbar (yeah thats right, i use Explorer )
When you managed to open the cover you can see at the right side that there is a very small flatcable. (this is the Digitizer cable)
You can open the connector by flipping the handle to vertical.
Use tweezers to unplug it.
Now you can flip the mainboard. As you can see there are 2 more flatcables unplug them with tweezers.
by the way: #1 is for the screen and #2 is for the buttons
Place the mainboard on a safe place so it can't be harmed.
Now the hard part!
Unscrew the 2 very small screws on the red spots and save them on a place where you can find them back again (I lost one and it took a half an hour to find it back on the floor with a magnet whehe)
Now the screen and the button-PCB is ready to take apart from the casing. A bit of the flatcable is glued so be patient.
When you managed to loosen the screen and buttons, place this part at a safe place so it can't be harmed.
Now this is tricky.
Now you have only a front casing with the digitizer.
It's very tight glued so you have to press at the back of the digitizer to loosen it. Be patient, you can break the casing of your device.
Also take care that you do not break the flatcable of the old digitizer because you have to place the cable of the new one at the same way, take a look at the old one when you placed it apart from the casing.
You have to flip the cable like this picture when you placed the new one in the casing.
when you did this, you can replace a little cushion which you had to remove from the flatcable from the old digitizer.
Now replace the screen and button part. replug the 2 flatcables, place the mainboard its place, replug the small flatcable of the digitizer (be sure that the handle is vertical when you do this. When the cable is plugged, place the handle horizontal.
Replace the backcover, the 4 screws, simcard and the memorycard and batterycover.
Press the on button.
Et voila!
As good as new :
The only issue is, that we do not have a dust free environment like HTC has.
The result:
Don't forget to calibrate
All the pictures are clickable.
Sorry for my bad English
And now one more beer and a long sleep
Thanks!
Thank you Marcello! I will give it one more try.
Hi Marcell-o your guide looks solid and the pics look nice...
You are from the Netherlands, where did you get your screen? I am from Belgium, that's why I am asking...
I have two problems with my Jade:
1) My screen is all scratched up, and I need to replace it, so for this only the upper part is needed, right?
2) A few weeks ago when I was in the bathroom and took the phone with me there is since a square "oily" stain in the middle of the screen. I read elsewhere that it's due to the humid enviroment, so I guess I need to replace the LCD part too?
I saw that the screws beneath the backcover are Torx, but what number Torx is it exactly, and is that same Torx used for the screws on the mailboard of the phone?
Thanks in advance for any answers!
Greetz
I bought it here: http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=260513873708
verry good price!
I'm sorry, i do not know the torx number i was just happy to have the right one.
What you need for the scratched screen is indeed the touchpart(digitizer)
The screws inside(for the buttons/screen) are just the four points(?)(kruisschroef) The mainboard is clicked.
Can you make a picture of the "oil" stain maybe it's also solved with the digitizer replacement.
Hi Guys,
just this morning I've managed to replace a digitizer in my Jade, as it was punctured by some pointy child's teeth . A bit unlucky though, cause I couldn't find this thread before (silly me !) as to get some instructions how to do that.
I'd like to add some tips to Marcell-o's guide:
1. The tools you need are:
TORX T6 screwdriver for 4 outside screws
Philips PH0 (or 00) screwdriver for 2 inside (button panel) screws
Thin Tweezers for replacing flat cables.
Office/Swiss knife for replacing Digitizer itself
2. To prevent any damage to your front cover, I would recommend to 'cut-off' the Digitizer from the inside, before pushing it out. I used a thin Swiss knife for this and started from the top corners, slowly going towards the bottom. This also left all (or most) of the glue at the case side so there was no need to apply additional glueing.
See attached Photo
[Sorry for adding like that, but I'm not allowed to add link as a new user]
3. To make your Jade scratch-proof as well as responding better to your fingers, I'd recommend the Advanced Screen Protector from ProPorta.com. It's nothing close to cheap crap from e-bay as 3 screens for a quid and literally increases touch sensitivity rather than decrease.
Good luck!
Catalan said:
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Click to expand...
Click to collapse
would you sell it as is ? Pm me/
zubenelgenubi said:
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Click to expand...
Click to collapse
and would you also ?
I am looking for some help/instructions as to how to do this. Has any one done this before? I am wondering if this would be easy or difficult.
Thanks in advance.
JSenthil
Here is information how to disassemble StarTrek http://forum.xda-developers.com/showthread.php?t=313066
Replacing is very easy, You only need to unscrew front cover. Few screws and lift front cover(first the plastic part, then more screws and metal part), unscrew screen and disconnect it. The front metal part sometimes doesn't lift but You'll figure out how to do it. And make sure you clean everything because dust always gets on the screens. Good luck.
Hi Kucyk,
Thank you for the link and explaining how to do it. This is exactly what I need. I appreciate it.
Thanks,
JSenthil
Hey guys, does anyone have any experience to share on changing the power button? Mine is flushed down and and it doesn't click. I saw the flex cable on sale on Aliexpress, do you know how easy/hard it is to repair (starting from the back cover removal...)?
Very easy. 10 to 15 minutes.
could you share the links and take pictures or video of the process when you do it?
Mine is already tilting a lot up and down. thanks!
https://www.youtube.com/watch?v=no0xV89CPMs&list=WL&t=132s&index=29
I think this is the most comprehensive video of p9000's disassembly
I've just replaced one and it's very easy.
Take back off, unscrew the top plastic cover to access the ribbon cable, remembering to unscrew the single screw with a sticker on it. The buttons just slide in and the ribbon cable clips in as usual.
check this video! https://www.youtube.com/watch?v=_Us9A-Il0AY&index=69&list=WL