Hello,
Please read the WHOLE post, as I've already done hours of XDA research and could not come across a similar situation.
I'm afraid that after months of flashing away, I've finally bricked my phone (for good).
I was ODINing back to stock from CM7, but something went wrong and ODIN froze. Not thinking it was a big deal, I took out the USB cable out.
This prompted my phone to not respond at all (no power, no recovery combo). However, searching around XDA, I found the way to enter download mode (through the plug in USB then plug in battery while holding volume buttons trick). I flashed the Froyo bootloaders, thinking that my bootloader was corrupted. This made the phone turn on to the "VIBRANT" screen, but nothing else. I still could not get into recovery mode through the 3 button combo.
I then proceeded to ODIN a JFD image, along with the 512 pit file. This put my phone into a non-responsive (read: no buttons work) state again, and so I flashed the Froyo bootloaders again. Once again, I was stuck at the "VIBRANT" screen.
Then I ODINed a JFD image without repartitioning with the 512 pit file. This continued to put my phone at the "VIBRANT" screen.
What went wrong?
I read up something about JTAG service; is this what I need? (From what I read, if you can access download mode, you're good to go, so I'm not sure if I "hard-bricked" my phone)
THANKS so much...
if you were on cm7 it was 2 button
3 button is for recovery
battery out\ reinsert battery
press volumeup\down insert usb cable.... downlod should appear
odin to stock
Sugartibbs said:
if you were on cm7 it was 2 button
3 button is for recovery
battery out\ reinsert battery
press volumeup\down insert usb cable.... downlod should appear
odin to stock
Click to expand...
Click to collapse
I can get into recovery, and I can ODIN to stock, but my phone is continually bricked--in fact, if I ODIN to stock, my phone doesn't turn on. (I know I'm doing it correctly because I've done it successfully before)
R you ona 3g samsung vibrant?
Sugartibbs said:
R you ona 3g samsung vibrant?
Click to expand...
Click to collapse
Yes, I have the original 3G Samsung Vibrant.
Sorry, but i had to ask, when you come out of odin and have green pass you should come out in recovery and either reboot or have an error message, yet you have the vibrant logo, is reboot checked? If all ese fails Aio toolbox, then you know pit, pda and if necessary drivers are correct. and not corrupted.
This is gonna take a bit more searching but your gonna have to find Eugene's froyo that doesn't brick. Odin that and then Odin back to stock maybe you can pm him for the files.
Sent from my SGH-T959 using XDA App
Sugartibbs said:
Sorry, but i had to ask, when you come out of odin and have green pass you should come out in recovery and either reboot or have an error message, yet you have the vibrant logo, is reboot checked? If all ese fails Aio toolbox, then you know pit, pda and if necessary drivers are correct. and not corrupted.
Click to expand...
Click to collapse
Thanks for all your help!
I figured out the problem--apparently the PDA file was corrupted. Internet here is spotty, so I guess it corrupted while downloading. I flashed the re-downloaded PDA file, and was able to un-brick my phone.
Related
I googled how to reset my phone back to factory settings and they gave me this link
"[STOCK ROM] Odin3 One-Click Downloader"
(cant link links)
i misread that it was for the captivate, and i went through with all the directions.
now my phone keeps flashing an AT&T bootscreen and i cant get it in recovery mode..
help?
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
nevermind, i found the Odin program for the samsung vibrant and re did it.. but i still have BOTH at&t boot screen at the tmobile vibrant boot screen.. anyone know how to get rid of that? it would be much appreciated thanks!
http://forum.xda-developers.com/showthread.php?t=741027
where did u find it.. please share..
Edit: NVM..
stepinmyworld said:
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
Click to expand...
Click to collapse
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Does not boot!
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
setzer715 said:
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Click to expand...
Click to collapse
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
stepinmyworld said:
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
Click to expand...
Click to collapse
I don't want your money, but if you PM me I will try to type up a detailed how to.
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Ok,
The_Chrome_Coyote really helped me!!!! Thank you so much and im back up and running. There was something missing from the original tutorial, not that we should be spoon fed but I didn't have the WinRAR program on my pc and didn't know I needed to extract anything. I was looking for exe. for it to be a program and just open it. It's a little more complicated than that. I added my additions in BOLD
The_Chrome_Coyote's Original post to me:
Odin isnt that hard, its just REALLY picky about working.
Firstly you need to download the Samsung drivers for your OS which can be found:
http://forum.xda-developers.com/showthread.php?t=728929
added:
Second you need to make sure you download WinRAR x86 (32 bit) 3.93 (google it and you should be able to get it) otherwise if your pc doesn't have a program to recognize rar and tar files, you are out of luck.
then read this thread from JAC:
http://forum.xda-developers.com/showthread.php?t=734475
1. Now, Extract ODIN from its .rar and place the .exe on your desktop
2. Extract the .pit file from its.rar and place that on your desktop
3. Place the JFD .tar file on your desktop but DO NOT EXTRACT
Now you can use ODIN
4. Start ODIN Odin3. [Android + SLP], through ODIN select the .pit file
5. Hit "PDA" button, and through ODIN select the .tar file
6. Plug your TURNED OFF PHONE into the USB cable
7. Wait for the Battery/ charging indicator to start
8. HOLD VOL UP+ VOL DOWN+ POWER, as soon as the screen goes black RELEASE POWER, and continue to HOLD VOL UP+ VOL DOWN Until it enters download mode. Which should happen quickly and looks like a men at work highway sign.
9. If a COM port has turned Yellow in ODIN, then the device has been recognized. If it hasnt, unplug and plug your phone back in.
10. Dont select any options other than whats set at default.
11. Hit Start and be patient, takes me maybe 5 minutes to get back up and running.
NOTE: If you do not see a blue progress bar on the phone's screen after a minute;
11a. Turn your phone off by pulling the battery.
11b. CLOSE ODIN
11c. Start at step 4 again.
ODIN needs to be open and ready to flash before the phone is plugged in, in my experience. Its very picking about this, and not everyone has this issue, but I did and following all these steps helped me flash my phone more times than I can count the other day haha.
Hope this helped! and your $20, donate it to Wes, JAC, or Eugene to keep them making great stuff for our phone.
Reply With Quote
Thank you thank you thank you
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
Same thing happened to mine when i tried odin. Now all i get sometime when it come on. are 7 rows of text that seems to be a code on screen in amber. Ishipped back 2 samsung. Since t-mobile won't take it after 14 days.
ok I screwed up guys.
I installed ROM manager from the market, flashed clockwork, it asked me if I wanted to partition and I said yes.
Now I just get a black screen at boot. I've managed to run odin and it says success. But I still just get a black screen after boot.
Little help?
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
daddysays said:
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
First: everyone was a noob at one time, so simmer down.
Second: Pleast post an update.zip that will make my phone work.
Cannot get past Galaxy S boot screen
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
jmoney1017 said:
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
Click to expand...
Click to collapse
If you can see the samsung logo you are fine. Load up recovery and try a full wipe first. If that fails then you can odin back to stock and root again.
Sent from my SGH-T959 using XDA App
1. If you have questions, there is a q and a forum for this device!!!!!!
2. THIS IS THE DEV PART OF THE FORUM. IE FOR DEVS POSTING STUFF FOR THE PHONE!!!!!
3. Learn how to Google. Not that hard. Example, you don't know what the *.rar extension is. GOOGLE IT!! Google knows everything.
4. If you don't have basic android or computer skills, don't try anything stupid. You do have a chance to brick your phone, even the pros like cyanogen have bricked their phones.
5. Don't offer cash for someone to fix your phone. Keep it in qna and some one will help you. Save your cash for the development that work hard on making these things work.
6. Can a mod please move this thread to qna.
7. THE MOST IMPORTANT THING. USE THE SEARCH FINCTION BUILT ONTO THE FORUMS. IT WILL SAVE YOU TIME AND THEN YOU WILL NOT LOOK LIKE NOOBS THAT JUST GOT THIS PHONE BECAUSE IT HAD AVITAR IN THE BOX!!!!!
Sent from my SGH-T959 using XDA App
cache.fs problem in odin
setzer715 said:
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Click to expand...
Click to collapse
I FOUND A SOLUTION TO THE CACHE.RFS PROBLEM!!
http://www.fractionalphones.com/?p=121
Hello everyone. I have a question about the current state of my Vibrant. Coming from a G1, I just upgraded to the Vibrant and have been loving since. I rooted my device, installed Clockwork Recovery, and flashed a new Rom. I decided to switch back to the stock rom but now when I turn on my Vibrant, it just sits at the Vibrant Samsung boot screen... Here are the steps I did up until this point:
1. Starting from the Stock T-Mobile rom, I applied Root update zip but booting into Recovery Mode (Holding down the volume Up/Down buttons and then pressing the Power button).
2. Installed Clockwork Recovery, and then did a Nandroid Backup.
3. Using Clockwork, I installed Eugene's Vibrant7 rom (I left create ROM Backup and Wipe Data options checked)
4. Vibrant7 rom flashed successfully but decided to switch back. So I used Clockwork to boot into manual recovery mode, selected Nandroid and then Restore
After it finished the Restore, it now sits at the Vibrant Samsung boot screen everytime I power it up... I'm thinking I should have not have used the Nandroid Restore to revert back to the stock ROM (unless I'm totally mistaken, I never used Clockwork Recovery before and have flash roms before with my G1).
At this point, could I just reflash back to the stock firmwire using ODIN (Directions from this thread [ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working) in the Vibrant/Android Development section). Would that take care of my problem or is my phone currently 'bricked' or SOL?
Thanks in advance for any help or clarification
yeah just odin back to stock... Read the directions carefully
this exact same thing is happening to me. I have tried to follow the instructions to odin. but when I hold volume down and power it just keeps rebooting to the vibrant page. but if I hold volume up and down and power I can get into recovery but non of the options fix my problem. Am I screwed or am I doing something wrong.
i'm having the same problem...stuck on boot screen
i'm on the bell network, are there instructions on how to use odin to fix my phone?
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
flashed a sgh t959 with a galaxy s i9ooo kernel oops
hi im stuck in manual mode and when i try to boot the screen shows two different galaxys s screens then goes back to manual mode and i cant get into down load mode it just goes back two manual mode was trying to root used wrong file i think im screwed i flash with oden and used i9000xxxhph tar file
Same with me, I think I soft bricked my vibrant, so I tried to restore to stock rom using odin. Odin detects it and runs stock rom just fine, but once it was restarting, the phone would not still boot up and would stay stuck at the vibrant samsung screen. I tried other roms such as froyo no brick, and i9000 stock rom also, would not boot also, just stuck at the samsung screen. What do I do? Odin works through the process fine though......why isnt it fixed?
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
yes yes yes! your mistake was using the power button! Lol.
FUTURE NOTE: if you upgrade to any gingerbread roms.... new bootloaders are required. If your JIG didnt get you into download mode before...... then it isn't working right. Once your into the the new Bootloaders for gingerbread, the sequence is........ HOLD VOL UP and POWER until you trigger DL mode. No USB required.... DO NOT FLASH NEW BOOTLOADERS WITHOUT A WORKING JIG IN YOUR POSSESION. TEST IT BEFORE YOU FLASH. I had...... an experiance.... lol
Not working
ParaMount33 said:
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
Click to expand...
Click to collapse
I tried all the instruction still stuck on Vibrant logo if i connect cable the Loader pix cums but doesnt load or show me battery image what to do now? also Odin doesnt recognize neither i can go to download mode!!!!!
If you can get in DL mode you are halfway there, next make sure you have correct drivers. Uninstall current drivers and reinstall correct drivers. Odin can be funny sometimes, you might need a new USB cable, try every USB port as well.
You can also use the All In One (AIO) program to get drivers and back to stock. If you are having issues with Odin try this
http://forum.xda-developers.com/showthread.php?p=11358713
sent from the depths of helly bean
hi,
Once i gt a prob restoring. But then I re-flashed the ROM which the nandroid backup was taken and then in CWM selected advance and gave restore data option(as i remember).. (it was not full restore with system..b/c I flashed system separately)
You can go back to stock using ODIN .. as mentioned by Daddy_617 previously.
tc
Also if Odin doesn't work for you try Heimdall. I've seen post where this has worked for others.
Vibrant stuck on "Vibrant Samsung"
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
I tried this but the say thing keeps happening ... really need help
Hello guys. My phone don't turn on when i press power button, VOL UP/DOWN buttons don't work also.
1. I flashed my vibrant with Unofficial TMO 2.2 Froyo ODIN *2E Recovery +SD Fixed Updated*11/09/10*. Don't know why after what i can't access download mode by 3 buttons. I had Android System Recovery <3e>.
2. After that i try go to download mode with battery out method, and it was fine. Next step was downgrade firmware to T959UVJE8-factory-final-MS_Guru.
3. After that i had "Android System Recovery <2e>" message
4. I tried to reinstall back Unofficial TMO 2.2 Froyo ODIN *2E Recovery +SD Fixed Updated*11/09/10* but something happend and Odin software Failed and i had "picture phone ! pc".
5. I tried both methods to go to download mode and after half an hour method with battery out and pushing vol up/down buttons accepted.
6. Then i tried to reinstall original firmware one more time. And it was fine. You can see screenshot in attachment.
7. But my phone after flashing turns off for rebooting and died.
When i trying to connect it with pc or charger nothing happens. Buttons don't work. Nothing on screen. Battery out not helped.
What to do??????
Did you try holding volume up and down and plug in usb cable method to get into download? I'm kind of wondering why you had those other files in there. The guides I saw just had the sit and the pda tar.
mbrockway said:
Did you try holding volume up and down and plug in usb cable method to get into download? I'm kind of wondering why you had those other files in there. The guides I saw just had the sit and the pda tar.
Click to expand...
Click to collapse
I think mbrock meant pit, not sit.
And yes, you only need the .pit and the .tar files.
~SB
mbrockway said:
Did you try holding volume up and down and plug in usb cable method to get into download? I'm kind of wondering why you had those other files in there. The guides I saw just had the sit and the pda tar.
Click to expand...
Click to collapse
Yes i tried this method. It doesn't work for me. I done all steps exactly how wrote MS_Guru in "Reflash Your Vibrant To Original Firmware"
bafxyz said:
Yes i try this method. It doesn't work for me. I do all steps exactly how wrote MS_Guru in "Reflash Your Vibrant To Original Firmware"
Click to expand...
Click to collapse
have you tried eugene's froyo that doesn't brick then go back to stock?
when going back to stock you only use the pda and the pit. that seems to be you problem.
Sent from my SGH-T959 using XDA App
iynfynity said:
have you tried eugene's froyo that doesn't brick then go back to stock?
when going back to stock you only use the pda and the pit. that seems to be you problem.
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
I used this one:
Eugene_SD+2E_JK2_Froyo Download >Vibrant_Full_Froydin_AND_2E_Recovery_+SD_Fixed
Unzip Download
&
Load s1_odin_20100512.pit into .pit at top of ODIN
&
Load Eugene_2E_JK2_Froyo.tar.md5 into PDA of ODIN
P.S. Tommorow i'll try to modify USB cable with resistors. Hope this will help me.
bafxyz said:
Hello guys. My phone don't turn on when i press power button, VOL UP/DOWN buttons don't work also.
1. I flashed my vibrant with Unofficial TMO 2.2 Froyo ODIN *2E Recovery +SD Fixed Updated*11/09/10*. Don't know why after what i can't access download mode by 3 buttons. I had Android System Recovery <3e>.
2. After that i try go to download mode with battery out method, and it was fine. Next step was downgrade firmware to T959UVJE8-factory-final-MS_Guru.
3. After that i had "Android System Recovery <2e>" message
4. I tried to reinstall back Unofficial TMO 2.2 Froyo ODIN *2E Recovery +SD Fixed Updated*11/09/10* but something happend and Odin software Failed and i had "picture phone ! pc".
5. I tried both methods to go to download mode and after half an hour method with battery out and pushing vol up/down buttons accepted.
6. Then i tried to reinstall original firmware one more time. And it was fine. You can see screenshot in attachment.
7. But my phone after flashing turns off for rebooting and died.
When i trying to connect it with pc or charger nothing happens. Buttons don't work. Nothing on screen. Battery out not helped.
What to do??????
Click to expand...
Click to collapse
was your battery low when your flashing ?
djkdawg said:
was your battery low when your flashing ?
Click to expand...
Click to collapse
It was almost full.
Trying cable method with resistors. Not working
I've got exactly the same problem
After trying to flash my phone with odin it went black and that's it, nothing can wait it up (
Email me [email protected]
The best phone in the world
Maybe this info will be helpfull. In this situation with dead Samsung Galaxy, Vibrant, Captivate only one ressurection. You need to open your mobile phone and reflash boot loader using RIFF Box JTAG which you can find only in service center. And you need to save your IMEI information which you must read from this address 0х80000 and this lenth 0хA80000. Thats all.
i tried that method you decscribed , now my phone is in MOde that say "power reset or unknown upload mode" any clue about how to get into download mode from this. odib detects my phone in this mode but i don't think it will load the software since it is not in download mode.
Today was I was watching the video on how to flash darky's resurrection.zip rom,
then zi tried flashing it to my wifes Vibrant , I folloeed the video step by step. I used odin I get the green light saying the phone passed then when it reboots it get stuck on the galaxyi900 screen and it doesnt boot up. Ive flashed the thing with odin at least 10 -15 times after and still no luck, it keeps getting stuck at the opening. My wife says if I dont fix it I have to buy her a new phone. Someone save me please!!!!!!
LMAO........... yeah my wife said the same thing...... sounds like you may have not disabled the voodoo lagfix before the flash.
you will probably need to flash back to stock. I am not sure what is stock on this phone I am going to assume it is the same Vibrant.
If you can get into recovery and you did have voodoo installed disable it. If not you can disable it on your phone and copy the folder and then load it into the internal sd card messed up phone and replace the old folder.
Then you may need to use Eugenes froyo that does not brick as a intermediary flash. if you can Odin that (use Odin 1.7) then when it you flash it do not check the repartition box. When it is beginning to reboot, do not let it fully reboot, pull the battery. Then Redo the Odin as described below:
Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Leave all check boxes the way they are. Check the repartition box.
Click the PIT button and select the 512.pit file
Click the PDA button and select T959JFD.tar and then click Start
When it is done you will be back at stock. Then Root the phone and go from there.
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
My phone just keeps flashing the opening Samsung galaxy s gt-i9000
Oh good I don't know the pit or .tar files sorry
Sent from my SGH-T959 using XDA App
Omar50 said:
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
Click to expand...
Click to collapse
take the battery out, wait 30 seconds, plug the usb cable in, and then hold both the volume buttons and slide the battery in. Presto! Download mode.
This has saved me numerous times lol. Then just flash JDF like oka said
i dont have problem entering download mode. When I flash with odin I get a pass on it. but when the phone reboots it stays on the opening screen go on and off
i download the heimdall suite 1.1.1 and the necessary windows program to run it. when i plug my phone into download mode heimdall start button isn't accessable. am i missing something?
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Omar50 said:
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Click to expand...
Click to collapse
Depends on what you smoke........
You may need the pit 513 file instead of the pit 512 file, these mapping files are a bit different and it may be a cause. Hard to know without seeing the phone
Also you could do a full wipe if you can get into recovery, wipe cache, phone reset and dalvik wipe (in advanced) then try That may work better for you.
It is recoverable.......... and also the best way to get your wife to calm down......... a romantic restaurant with candle light........ you go on Tuesday and she goes on Thursday........
Hope you get it fixed..........
thanks for the support but no luck I tried 513 pit nothing my phone still wont boot up I still get the opening screen then it shuts off and starts again.
im really having a bad day now i tried flashing the stock rom 2.2 with odin now the phone wont even power on! i guess its really a brick. i bought myself a paper weight
I searched Stuck on Vibrant screen and tried everything I could. What else can I try???
I bought this phone from a friend who said it just froze on him. He wasnt rooted or anything.
----When I turn on the phone it gets to the vibrant screen and stays there.
--If I try the three button method, letting go of the power button when the vibrant screen comes on, it then starts a boot loop of that screen only.
----Get into download mode and using ODIN 1.70, I use the T959UVJFD and vibrant512.pit with re-partition checked and also unchecked. It stays stuck on Vibrant Screen for 20 minutes.
--Then I try the 3 button and same thing happens
----I ODIN "Eugene_2E_JK2_Froyo.tar.md5" and "s1_odin_20100512.pit" with re-partition checked and unchecked. It then gets into a boot loop of the little circle timer symbol, like its thinking or getting ready to charge for 20 minutes.
--Try the 3 button salute and get the vibrant screen boot loop.
----Try just turning it on and it just gets stuck on vibrant screen for 15 minutes.
----I then tried flashing the Zimage from "stock+Voodoo-Froyo-T959-UVJK6" kernal with re-partition checked and unchecked.
--Tried the 3 button salute both times and I still get the Vibrant boot loop.
I also tried with the T959UVJI6, get same results.
CAN SOMEONE PLEASE HELP ME. I DONT KNOW WHAT ELSE TO DO
First, i would recommend you to download the AIO Vibrant Toolbox because it have all the files you need, the latest version of Odin and all the instructions. Did you try unchecking re-partition when using Odin?
About your phone, usually, when you are able to go into download mode, and Odin can see your phone, you are not bricked, except, if there is any hardware issues.
Thanks for the quick reply.
I will try that next and then report.
Thank u.
Oh and yes I did try both checked and un-checked
So downloaded the AIO Vibrant Toolbox and tried using it with no success.
Still gets stuck on vibrant screen while waiting 20 min, even after battery pull the 3button salute will not work and it is still stuck on vibrant screen.
Any other ideas??
power off the phone
open odin
hold volume up and down
plug usb in
or
open odin
pull the phone battery
plug usb in
hold vol up and down
push battery back in (while holding vol buttons)
both of these ways should put you in download mode, if they dont straight away just keep trying and try different ports on your computer
kyle51 said:
power off the phone
open odin
hold volume up and down
plug usb in
or
open odin
pull the phone battery
plug usb in
hold vol up and down
push battery back in (while holding vol buttons)
both of these ways should put you in download mode, if they dont straight away just keep trying and try different ports on your computer
Click to expand...
Click to collapse
Thanks, but I am able to get into download mode and complete the ODIN. But when the phone resets, it stays on the Vibrant Samsung screen.
boner2007 said:
Thanks, but I am able to get into download mode and complete the ODIN. But when the phone resets, it stays on the Vibrant Samsung screen.
Click to expand...
Click to collapse
So Odin finishes flashing, then it continues to loop?
You're US T-Mobile Vibrant correct?
I personally used this:
http://androidspin.com/2010/08/09/how-to-restore-or-recover-your-samsung-vibrant/
Use this: T959UVJFD.tar (worked for me, updated easily)
http://files.androidspin.com/downloads.php?dir=androidspin/samsung/vibrant/&file=T959UVJFD.tar
P.S.: Use the latest version of Odin. Search in the forums.
Yessir, it continues to loop.
It is the us tmo.
I believe I used odin ODIN 1.87 or somthing like that from the AIO Toolbox. I will try those links and search to sdee if there is a newer ODIN.
I really appreciate the help. I tried my best explaining everything I tried in my OP. Except now I am using the ODIN 1.87.
boner2007 said:
Yessir, it continues to loop.
It is the us tmo.
I believe I used odin ODIN 1.87 or somthing like that from the AIO Toolbox. I will try those links and search to sdee if there is a newer ODIN.
I really appreciate the help. I tried my best explaining everything I tried in my OP. Except now I am using the ODIN 1.87.
Click to expand...
Click to collapse
Good luck, with the link I gave it should work and put your Galaxy S back to 2.1.
ODIN3 v1.7 - Thats the one I use. Good luck!
MasterGGM said:
I personally used this:
http://androidspin.com/2010/08/09/how-to-restore-or-recover-your-samsung-vibrant/
Click to expand...
Click to collapse
I love to reference that article!! LOL. I like the way that one starts, "So you've messed it up huh,....." rofl. That and it mentions JAC/JAD's thread, oh those were the days.
I got caught in the boot loop about a week ago and this worked for me as nothing else did to get back into recovery screen.
I don't remember if I pulled the battery or restarted the phone, but either way, once the phone was powered down, I held down the power button and both volume buttons, I waited until the VIBRANT logo came back up and BLINKED ONCE, then let go of only the power button, then I immediately hit the home button.
This brought me right back into recovery mode, well, clockwork recovery at which time I reflashed the rom prior that was working fine.
Might be worth giving it a shot.
I encourage you not to give up. I've been in similar situations before, and I always find it helps to exercise precise controls on your resuscitation attempts. Try using the same procedure in different USB ports, try using the same procedure 2 or three times in a row. Try Eugene's Froyo that does not brick and then going to stock JFD and then back to Eugene's again. Maybe try Heimdall.