Related
Hi all. I have multiple problems in my x10i.it has 2.1 It was rooted and worked fine..few days ago I tried to wipe the phone and did the master reset via xrecovery ..after the restart it just hanged at the boot logo and xrecovery is not working from then....I wanted to update with SEUS via USB... but the phone is not connecting as well...What should I do? PLZ HELP ME GUYZ........
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
If SEUS/PCC doesn`t recognize your phone, remove them from PC and reinstall them.
You have an USB driver problem
ohm74 said:
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Click to expand...
Click to collapse
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Take the phone with the warranty for repairing.
mistake_man said:
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
Click to expand...
Click to collapse
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
iMatth3w said:
Take the phone with the warranty for repairing.
Click to expand...
Click to collapse
I bought it from ebay ...no warrenty... think thats stupid :/
rumanbsl said:
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Click to expand...
Click to collapse
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
rumanbsl said:
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
Click to expand...
Click to collapse
Well your usb is definitly working then as its glowin green?..
Are you sure you are doing it all right? It happened the same to me, and it ended I was pressing the wrong buttom (I knew which one was the correct one, but was blind cause I was scared that Ive broke it totally), a day later I noticed it and I was able to flash my phone.
However, read a guide and follow it step by step, reinstall everything and start from beginning maybe?
Or use the repair function with PC Companion
Hi! I had the same problem!
1. Search and download from this forum Flashtool 0.2.6
2. Install it.
3. Download from this forum one generic ROM (for exemple X10i_2.1.A.435_GLOBAL-GGL GENERIC 1232-9897 )
4. Put the file in directory Flashtool/firmware
5. Launch X10flashtool.exe
6. DO NOT PUT THE USB CABLE IN THE PHONE
7.From option "flash select the desired ROM
8. Wait the program to begin(a picture will appear)
9. Pressing the back button, insert the usb cable.
10. Wait the flashing to begin and release the back button.
Follow instructions and WAIT around 5 minutes until flashing will complete
11. Send me two words if it helps you! Success!
ohm74 said:
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
Click to expand...
Click to collapse
I've did everything as u told.....no luck ! guess its the time to go to repair center...btw a guy from help center told me about software tampered,,!!out of luck
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
jakadewantara said:
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
Click to expand...
Click to collapse
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
try thread from DoomLORD : [DEV][How-To] Get Back to Stock Even With Broken / Damaged USB Port in http://forum.xda-developers.com/showthread.php?t=1054818
tarzerixx said:
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
Click to expand...
Click to collapse
Likely the USB port is dead and you have to send it in for repair.
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
pccobra said:
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
Click to expand...
Click to collapse
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
RedAxe said:
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
Click to expand...
Click to collapse
Hapenned the same to me...
I try to follow the steps, but i can't pass step 4 (it's unavaiable the "clean cache" bottom...)
Please help...
Restore original firmware with SEUS
RedAxe said:
...then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen...
Click to expand...
Click to collapse
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
do u have trick for my problem here forum.xda-developers.com/showthread.php?t=1388476
my x10 just vibrate once and stack on blank screen.
Sent from my X10i using Tapatalk
When I use SEUS It keep saying "You have the newest software available"
I tried the hard reset and all. The phone now just won't start at all
Hi,
i got the same problem what you describe ive stuck at the SE logo and cant get into recovery and i cant use flashtool. i tried to do what you say in the first post, but when i press the shell root button, it says "wait for device" then its not responding, and i cant moce on to the next step... what should i do now?
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
u totally saved me =D
X10 mini revived!
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
cruzstar said:
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
Click to expand...
Click to collapse
Update phone using SEUS....
Just google SUES
Definitely it will work....
Sent from my X10i using xda premium
yea i have use the SEUS..by pressing the back button..but it dont work..plz help me
Dear sir i already done that procedures but no use in seus shown u already updater software. plz help me
Cannot unbrick xperia mini E10i
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
Hello Guys,
I need your urgent help.
I cannot restore phone with SEUS or Companion. It says I already have the soft.
Getting fatal errors in Flashtool, I am stuck with SE logo and bootloader relocked.
I have the stock kernel but CM7 ROM.
Do you have any other ideas?
Tanks a lot!
deBelch said:
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
Click to expand...
Click to collapse
nope...didnt work...there is NO Install beneath...wonder why? is it i am using the latest SEUS?
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few seconds it boot automatically. and when i try to flash anything it boot automatically. please help me
---------- Post added at 12:21 AM ---------- Previous post was at 12:16 AM ----------
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few minutes it boot automatically. and when i try to flash anything it boot automatically. please help me
i am using minicm7 2.11,use cwnrecovery to update 2.13,boot in cwm then select install zip select file,after have error,now halt on start up "Sony Ericssion",can't power off,just can reboot,but press back up also no respond,please help me
eritang said:
i am using minicm7 2.11,use cwnrecovery to update 2.13,boot in cwm then select install zip select file,after have error,now halt on start up "Sony Ericssion",can't power off,just can reboot,but press back up also no respond,please help me
Click to expand...
Click to collapse
did you unlock bootloader?
did you flash naa v5 kernel?
everything is explained in the first page of minicm thread..
if you think you are not able to do that please revert to stock via repair option in sony-ericsson pc companion software
Gx3 said:
did you unlock bootloader?
did you flash naa v5 kernel?
everything is explained in the first page of minicm thread..
if you think you are not able to do that please revert to stock via repair option in sony-ericsson pc companion software
Click to expand...
Click to collapse
THANKS,i have try it,but the step of press back key and plug usb have problem,because i can't power off the phone,any solution?
eritang said:
THANKS,i have try it,but the step of press back key and plug usb have problem,because i can't power off the phone,any solution?
Click to expand...
Click to collapse
you can power off the phone by pressing and holding simultaneously back and power button until it reboots (equivalent to power off), when the screen goes blank release and press and keep back button pressed
@eritang: You can repair it with PC Companion and go back to stock firmware for short. Use under support the repair phone function. It's a little bit problematic to find the phone when it reboots all the time.
Press home button (middle), back button (right) and power button at the same time. Your device is shutting down completly.
You will be asked to connect your device for flashing ...
Press power to turn it on and fast after that the back button (hold) and insert the usb cable. Then, you're in flashmode.
After flashing, restart your device and be happy
I hope, this can help ;-)
P.S.: You can try to install the custom rom this time correctly. I can give you some help !!!
P.P.S.: My E10i is running fine with nAa Kernel 05 & miniCM7-2.1.3 ^^
Schmiddie23 said:
@eritang: You can repair it with PC Companion and go back to stock firmware for short. Use under support the repair phone function. It's a little bit problematic to find the phone when it reboots all the time.
Press home button (middle), back button (right) and power button at the same time. Your device is shutting down completly.
You will be asked to connect your device for flashing ...
Press power to turn it on and fast after that the back button (hold) and insert the usb cable. Then, you're in flashmode.
After flashing, restart your device and be happy
I hope, this can help ;-)
P.S.: You can try to install the custom rom this time correctly. I can give you some help !!!
P.P.S.: My E10i is running fine with nAa Kernel 05 & miniCM7-2.1.3 ^^
Click to expand...
Click to collapse
Sorry,i use flash tool sucessful,power on now no show sonyericsion just reboot,help
use SEUS (Sony Ericsson Update Service),when phone reboot,klik and hold back button 30 sec.SEUS download oryginal firmware and flash your phone
marcinwlkp said:
use SEUS (Sony Ericsson Update Service),when phone reboot,klik and hold back button 30 sec.SEUS download oryginal firmware and flash your phone
Click to expand...
Click to collapse
but update service said my software most update,no update
now i use flash tools show this error,i have not unlock bootloader?i try method to unlock but still not work,and now power on x10i just blank screen,no sony ericssion now,please helpthank you
Why not using PC Companion with phone repair function? Look under "support". Reflash the stock firmware and your device will be working ;-) After that, you can try all other things
Sent from my E10i using xda premium
My phone was working, I had MiniCM7Pro V21 Installed and I tried to install the CWM Recovery Version 5, because in my installed version the Battery Stats Wipe wasn't working and my battery was draining very quickly.
After the CWM Recovery Version 5 Installation my phone got bricked because it's getting stuck in Sony Ericsson Text.
I am trying to Reflash but only Flash button is active and it doesn't show any firmware though I have copied both zip and unzipped files in firmware folder in FlashTool_0.2.9.1
I tried to use SuperOneClick to root but it gets stuck in Waiting for device. Kindly help.
It gives the following error :-
OK
Pushing rageagainstthecage...
error: device not found
FAILED
I have installed it.
ggsetup-2.2.0.10
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Thank you for the reply, the black screen do u mean the black screen with Sony Ericsson Text ? When I Press Home+Power Button I can see the Sony Ericsson Text Black Screen and then I press and hold the back buton Pluging my phone into computer I keep on seeing the Sony Ericsson Text Black Screen with no green flashlight.
I am still trying.
Black screen without any logos. Just black screen. Don't forget to hold back button.
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
camelgrg said:
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
Click to expand...
Click to collapse
reflash to stock kernel and ROM
- install PC companion.
- connect phone in repair mode
- install drivers.
- after driver installed, reflash stock kernel using flashtool
- after stock kernel installed, reflash stock ROM using PC companion
- after stock kernel and ROM flashed,your phone should be like just when you bought it.
- bootloader should be locked now
- Root again
- unlock bootloader again
- Flash nAa again
- Flash cm7 again
- DONE!
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Ones again: to enter restore mode you have to power off your phone, using home+power buttons or powering off like I have on picture. Then press and hold back button, while plugging it into computer.
camelgrg said:
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Click to expand...
Click to collapse
- To relock bootloader you need to flash stock kernel which is 2.1.0.a.06 kernel.
- You need to flash stock kernel because if you have nAa kernel or any custom kernel installed, you wont be able to repair your phone using pc companion.
- After flashing stock kernel:
1. open pc companion
2. click support zone. (click start below it)
3. after clicking start, there should be a new window which also has a "start button"
4. on the 2nd start button, there should be a button under it which says "repair"
5. after clicking repair, just follow the steps for you to connect your phone in repair mode.
6. complete the repair installation.
7. DONE!
8. Bootloader should be locked now.
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
camelgrg said:
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
Click to expand...
Click to collapse
You are welcome my friend
And how should I proceed if I have a really hard brick (u20a)?
I tried to flash nAn on it, followed some instructions to unlock the bootloader, but something went wrong, the results were not the ones that should had been, and I made the mistake of turning it off. Now whenever I try to power it on, it doesn't do squat.
The only thing that makes me think it's still alive is that (after several months) I plugged it in and it began blinking on red (perhaps really low battery).
I've tried to pull the battery, put it back in, press back (keeping it pressed), and then plugging the cable to the computer and nothing.
Any ideas? Or should I flush it down the toilet? :crying:
x10 mini unbricking
Mrakoris/ said:
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Click to expand...
Click to collapse
i tried the thing you suggested, but the green light only lasts a while even if i continue to hold the back button. also, i am not able to repair my phone through se pc companion, as it keeps cancelling the repair update the moment the green light stops appearing. any help? thanks!
Hi,
I would like to ask you for advice before throwing my X10 mini away and buying something else.
I have had MiniCM7 installed for a very long time (more than a year), and upgraded to all versions without any problem. Today I installed MiniCM9 3.0.2, but I decided to reinstall MiniCM7 because of some problems detected with this version, so I went to SEUS, downgraded to 2.1.1.A.0.6, installed BusyBox, xMiniRecovery, root and flashed MiniCM7 2.2.0 and gapps. I have done it quite a lot of times before.
But, when I tried to reboot onto MiniCM7 2.2.0, my phone was stuck onto Sony Ericsson logo. Here's what I did:
1) Ok, Home+Power and reenter into recovery by pressing back key. No, no luck, it doesn't enter into any recovery.
2) B plan, I'll go to SEUS again. Home+Power, connect USB and keep back key pressed. Nothing, SEUS doesn't recognize anything, but Companion does activate a little popup on my Windows, as if it detects my phone plugged into my computer. No red, yellow, or green lights in the phone.
3) C plan. Flash kernel directly. I downloaded kernel from http://forum.xda-developers.com/showthread.php?p=17674938#post17674938 and used FlashTool. But, again, when I press Home+Power, connect the USB cable and press back key, it doesn't recognize anything, FlashTool is waiting for me to connect something. Antivirus is disabled.
If I keep back key pressed, no SE logo appears; black screen. If I release back key for a little while, SE logo appears and it gets stuck.
Both if I connect it to the computer or to the power socket, no green/yellow/red led appears.
Does anybody have any idea? Everything (cable and phone) were working wonderfully before flashing 2.1.1.A.0.6 for the last time.
Kind regards,
Jordi
Ok,before u try this u should know it will delete everything of phone memory:apps,contacts,etc.
And it removes root and recovery and phone will be like the day u bought it except that bootloader is not touched if unlocked stays unlocked
TRY AT UR OWN RISK
Steps:
1-download sony erricsson pc companion
2-click support zone and choose software update
3-before clicking continue click on repair phone
4-wait till loads and choose phone type
5-concentrate on this one cuz it has 2 methods
5a:if ur phone doesent restart automaticlly just plug usb in computer first then with phone powered off hold the back button and connect the usb cable only let hold when it says u can
5b:if ur phone DOES restart automaticlly remove battery till u reach this step and put back cover bedside till ur done with this method what were gonna do is when we reach this step we quickly plug battery and before it restarts just hold back and insert usb cable.
6-wait to install
7-congratulations unbricking
8-(optional):click the thanks button :xD
Sent from my U20i using XDA
Hi,
Thank you very much for your quick answer. I had never realized the procedure shown in steps 2-4.
But Companion refuses to install it! "It's impossible to install or setup update components of phone sotfware" grrrrrrrrrrrrr Tomorrow I'll try to get another computer and follow your procedure.
Thank you very much
Always happy to help as ive been in such issues alot
Sent from my U20i using XDA
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
SmG67 said:
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
Click to expand...
Click to collapse
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
jordisegurapla said:
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
Click to expand...
Click to collapse
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I've tried that already, doesn't work...
Looks bad, huh???
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I do not know what did I do, but by trying for the 1000th time to do the Home+Power+Back key combination with USB connected and keeping Back key pressed, and pressing and releasing it madly afterwards, while FlashTool was waiting for me to flash MiniCM7, FlashTool has reacted!!!!!! It allowed me to install MiniCM7 again!!!
What happened? I do not know, perhaps I pressed Back key just the microsecond that the hardware needed it.
Thank you very much!!!!
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
SmG67 said:
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
Click to expand...
Click to collapse
Ok, you are right again; FlashTool allowed me to install the kernel ;-) and then, everything else.
Thank you very much, really!!!