i am using minicm7 2.11,use cwnrecovery to update 2.13,boot in cwm then select install zip select file,after have error,now halt on start up "Sony Ericssion",can't power off,just can reboot,but press back up also no respond,please help me
eritang said:
i am using minicm7 2.11,use cwnrecovery to update 2.13,boot in cwm then select install zip select file,after have error,now halt on start up "Sony Ericssion",can't power off,just can reboot,but press back up also no respond,please help me
Click to expand...
Click to collapse
did you unlock bootloader?
did you flash naa v5 kernel?
everything is explained in the first page of minicm thread..
if you think you are not able to do that please revert to stock via repair option in sony-ericsson pc companion software
Gx3 said:
did you unlock bootloader?
did you flash naa v5 kernel?
everything is explained in the first page of minicm thread..
if you think you are not able to do that please revert to stock via repair option in sony-ericsson pc companion software
Click to expand...
Click to collapse
THANKS,i have try it,but the step of press back key and plug usb have problem,because i can't power off the phone,any solution?
eritang said:
THANKS,i have try it,but the step of press back key and plug usb have problem,because i can't power off the phone,any solution?
Click to expand...
Click to collapse
you can power off the phone by pressing and holding simultaneously back and power button until it reboots (equivalent to power off), when the screen goes blank release and press and keep back button pressed
@eritang: You can repair it with PC Companion and go back to stock firmware for short. Use under support the repair phone function. It's a little bit problematic to find the phone when it reboots all the time.
Press home button (middle), back button (right) and power button at the same time. Your device is shutting down completly.
You will be asked to connect your device for flashing ...
Press power to turn it on and fast after that the back button (hold) and insert the usb cable. Then, you're in flashmode.
After flashing, restart your device and be happy
I hope, this can help ;-)
P.S.: You can try to install the custom rom this time correctly. I can give you some help !!!
P.P.S.: My E10i is running fine with nAa Kernel 05 & miniCM7-2.1.3 ^^
Schmiddie23 said:
@eritang: You can repair it with PC Companion and go back to stock firmware for short. Use under support the repair phone function. It's a little bit problematic to find the phone when it reboots all the time.
Press home button (middle), back button (right) and power button at the same time. Your device is shutting down completly.
You will be asked to connect your device for flashing ...
Press power to turn it on and fast after that the back button (hold) and insert the usb cable. Then, you're in flashmode.
After flashing, restart your device and be happy
I hope, this can help ;-)
P.S.: You can try to install the custom rom this time correctly. I can give you some help !!!
P.P.S.: My E10i is running fine with nAa Kernel 05 & miniCM7-2.1.3 ^^
Click to expand...
Click to collapse
Sorry,i use flash tool sucessful,power on now no show sonyericsion just reboot,help
use SEUS (Sony Ericsson Update Service),when phone reboot,klik and hold back button 30 sec.SEUS download oryginal firmware and flash your phone
marcinwlkp said:
use SEUS (Sony Ericsson Update Service),when phone reboot,klik and hold back button 30 sec.SEUS download oryginal firmware and flash your phone
Click to expand...
Click to collapse
but update service said my software most update,no update
now i use flash tools show this error,i have not unlock bootloader?i try method to unlock but still not work,and now power on x10i just blank screen,no sony ericssion now,please helpthank you
Why not using PC Companion with phone repair function? Look under "support". Reflash the stock firmware and your device will be working ;-) After that, you can try all other things
Sent from my E10i using xda premium
Related
Hello, Im trying to flash my phone with Jerpelea`s tutorial, but I cant put this phone in Flash mode, it says to hold the Back button after power it off, but it seems to have no effect at all...
also hold the back buttom while powering the phone doesnt work...
can someone help me please??
Hold back button down first then plug USB in and continue to hold back button
Hello A have the same problem is there a other whay?
Thanks
you have to switch the phone off.. take out the battery for 5 seconds (min).. then.. this is the bit you need three hands for... you need to hold the back button whilst plugging in the USB cable.. continue to hold the back button until the software tells you to let go..
Whill this work for de x10i ??
Resisting the temptation for sarcasm....
Yes, it's the x10i method.
Sent from my X10i
Sorry, I don't understand.. because on my x10 with froyo beta2 hotfix1 of zdzihu, this method does not work...
Italiano38 said:
Sorry, I don't understand.. because on my x10 with froyo beta2 hotfix1 of zdzihu, this method does not work...
Click to expand...
Click to collapse
There is only only method for the X10a/i/mini/mini pro/1.6/2.1/2.2 into flashmode, as Mr Iceman has already explained, if it doesn't work for you you're doing something wrong or your phone is broke. To save having to use 3 hands, plug the lead into the phone first, then attaching it to the PC is a much simpler task.
Oki, thank you, I will test it later because I have a bigger problem like I said here: http://forum.xda-developers.com/showthread.php?p=10781800#post10781800
Is this method work for the latest xperia mini pro[SK17i] ?? pliz.. im newbie here..
My xperia sola cannot be put into into flashmode. as i connect the usb while holding the volume down key the green light appear and after 5 seconds the green light is out and change to red one and the phone shows the sony logo.
please help me how to install or connect my xperia sola to flash mode. tnx
tsoytsoy1880 said:
My xperia sola cannot be put into into flashmode. as i connect the usb while holding the volume down key the green light appear and after 5 seconds the green light is out and change to red one and the phone shows the sony logo.
please help me how to install or connect my xperia sola to flash mode. tnx
Click to expand...
Click to collapse
Xperia sola is different than x10
so if you ask in xperia S forums you will get your answer
Teio said:
Hello, Im trying to flash my phone with Jerpelea`s tutorial, but I cant put this phone in Flash mode, it says to hold the Back button after power it off, but it seems to have no effect at all...
also hold the back buttom while powering the phone doesnt work...
can someone help me please??
Click to expand...
Click to collapse
Hey Teio, check if that video works for you, avoid all the information just pay attention on the hardware process:
Turn off phone or take out battery
Conect your USB cable to PC
Open Flashtool
Select Kernel that you wanna flash
Wait for pop up message
Connect your phone
Hold back button
Re Insert Battery
Put Xperia x10 in flash mode
Regards
Press volume down button
radiation626 said:
Is this method work for the latest xperia mini pro[SK17i] ?? pliz.. im newbie here..
Click to expand...
Click to collapse
Since back key is feather touch button it won't work while phone is switched off....., So those phone you should press volume down button instead...
vijay.pushkin said:
Since back key is feather touch button it won't work while phone is switched off....., So those phone you should press volume down button instead...
Click to expand...
Click to collapse
I have the same problem, this metod don´t work in the xperia mini pro[SK17i], 'press volume down button' isn´t recognized
whit a command according to forum 'supported devices' . How can i flash this model of xperia now?
Hello everyone, i'm sorry for my bad English, I accidentally moved the "app" folder from the system to the sd card using root explorer, and I have lost almost all applications (market, root explorer, astro, ecc...), then I try to resolve this problem doing a hard reset , but now the phone goes on and after about 1 minutes goes off again again and again, and I can not stop it. also does not connect to pc .. anyone knows a way to fix it? I think I'll take it in assistance, the phone is still under warranty but it was rooted
Thank you guys
maicolboss said:
Hello everyone, i'm sorry for my bad English, I accidentally moved the "app" folder from the system to the sd card using root explorer, and I have lost almost all applications (market, root explorer, astro, ecc...), then I try to resolve this problem doing a hard reset , but now the phone goes on and after about 1 minutes goes off again again and again, and I can not stop it. also does not connect to pc .. anyone knows a way to fix it? I think I'll take it in assistance, the phone is still under warranty but it was rooted
Thank you guys
Click to expand...
Click to collapse
flash using binarys guide or repair from seus
Unfortunately i can't connect my phone in flash mode...
maicolboss said:
Unfortunately i can't connect my phone in flash mode...
Click to expand...
Click to collapse
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
You're a genius!!!!.... I thought my phone was dead.... but now is resurrected ... thank you so much!!
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
Dude, you're a machine - my phone wouldn't power off so i was waiting for it to run flat lol... your post helped a ****load to get my phone repaired.
Thanks!
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
had the same issue of not being able to connect my phone to pc to repair with seus. thanks loads the "press both midle and right button at the same time and press the power button" trick!!!
I tried your solution but seus just tell me my mini it's up-to-date and there's no more the button for installing anyway android.
The phone just reboots over and over
I seem to have a slightly different problem. I tried the process and right after it said that the phone is connected, the green light on the phone goes out and it looses connection to the phone and prompts me to reconnect. My phone is stuck on the sony ericsson logo, will not shut off and will not boot, can not be detected by the computer. I think I have little more than a very expensive hockey puck.
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
THANKYOU THANKYOU THANKYOU THANKYOU THANKYOU
Could never live without my phone, thankyou your the best
lije87 said:
I tried your solution but seus just tell me my mini it's up-to-date and there's no more the button for installing anyway android.
The phone just reboots over and over
Click to expand...
Click to collapse
try this mate
http://forum.xda-developers.com/archive/index.php/t-981935.html
I have the same problem SEUS says my phone is "up-to-date" what can we do?
Hey yhis helped me too thanks !
something similiar too...
Hi,
Here is my problem.
I have Xperia x10 mini/ yesterday , but mistake, I installed the firmware of the X10 mini PRO !!!
Now, once I understood the mistake, I want to flash with x10 mini firmware.
In order to flash I need to have FLASHTOOLS and need to press the BACK button - the problem is that since the phone is using now the wrong firmware, the BACK button (needed for the flushing ) doesn’t do anything and thus, I cannot install the correct firmware. I tried pushing all other buttons without any luck.
Any idea how I can overcome this problem ? I can’t use my phone now.
ramimos said:
Hi,
Here is my problem.
I have Xperia x10 mini/ yesterday , but mistake, I installed the firmware of the X10 mini PRO !!!
Now, once I understood the mistake, I want to flash with x10 mini firmware.
In order to flash I need to have FLASHTOOLS and need to press the BACK button - the problem is that since the phone is using now the wrong firmware, the BACK button (needed for the flushing ) doesn’t do anything and thus, I cannot install the correct firmware. I tried pushing all other buttons without any luck.
Any idea how I can overcome this problem ? I can’t use my phone now.
Click to expand...
Click to collapse
The flashmode is initialized before any firmware is loaded, so that isn't your problem
It should always work when your phone is turned off, you press the back-button and attach it to your usb-cable, it should enter flashmode.
If you can't turn it off, connect your phone to your pc, press home and power together till the screen goes black, and then press the back-button.
Well,
I managed to turn the phone off ( using the home+power button), then release the two of them, pressing the BACK button and connecting the USB cable .
nothing hapenns till i release the BACK button and then the phone starts to load with the previous problem.
before installing the the wrong firmware, using the BACK button was OK.
any idea?
update
I managed to hold together the HOME+BACK button and then pushed the POWER button and flashed the E10i 2.1.1 A.0.6 firmware!!!!
while doing it, i noticed for a meesage that the phone is not rooted.
upon finishing the flashing, the phone doesnt boot up, i managed to see the green light and thats all.
i also downloaded the S1 tool in order to root the phone but it says that it can not detect the phone....
what should i do now?
---------- Post added at 01:11 PM ---------- Previous post was at 12:15 PM ----------
update #2
phone doesnt boot up.
when i connect the flashtool i get the message "Device connected in flash mode".
how to continue from that point ?
Hi all. I have multiple problems in my x10i.it has 2.1 It was rooted and worked fine..few days ago I tried to wipe the phone and did the master reset via xrecovery ..after the restart it just hanged at the boot logo and xrecovery is not working from then....I wanted to update with SEUS via USB... but the phone is not connecting as well...What should I do? PLZ HELP ME GUYZ........
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
If SEUS/PCC doesn`t recognize your phone, remove them from PC and reinstall them.
You have an USB driver problem
ohm74 said:
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Click to expand...
Click to collapse
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Take the phone with the warranty for repairing.
mistake_man said:
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
Click to expand...
Click to collapse
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
iMatth3w said:
Take the phone with the warranty for repairing.
Click to expand...
Click to collapse
I bought it from ebay ...no warrenty... think thats stupid :/
rumanbsl said:
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Click to expand...
Click to collapse
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
rumanbsl said:
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
Click to expand...
Click to collapse
Well your usb is definitly working then as its glowin green?..
Are you sure you are doing it all right? It happened the same to me, and it ended I was pressing the wrong buttom (I knew which one was the correct one, but was blind cause I was scared that Ive broke it totally), a day later I noticed it and I was able to flash my phone.
However, read a guide and follow it step by step, reinstall everything and start from beginning maybe?
Or use the repair function with PC Companion
Hi! I had the same problem!
1. Search and download from this forum Flashtool 0.2.6
2. Install it.
3. Download from this forum one generic ROM (for exemple X10i_2.1.A.435_GLOBAL-GGL GENERIC 1232-9897 )
4. Put the file in directory Flashtool/firmware
5. Launch X10flashtool.exe
6. DO NOT PUT THE USB CABLE IN THE PHONE
7.From option "flash select the desired ROM
8. Wait the program to begin(a picture will appear)
9. Pressing the back button, insert the usb cable.
10. Wait the flashing to begin and release the back button.
Follow instructions and WAIT around 5 minutes until flashing will complete
11. Send me two words if it helps you! Success!
ohm74 said:
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
Click to expand...
Click to collapse
I've did everything as u told.....no luck ! guess its the time to go to repair center...btw a guy from help center told me about software tampered,,!!out of luck
Hi to all,
i'm trying to install the MiniCM7.
I rooted, installed xrecovery an unlocked the bootloader correctly.
After installed the latest E10_nAa-06 the phone rebooted and the nAa screen appear, than disappear but noting.
The phone doesn't answer.
i can't turn off or turn on the phone.
i've tried with pc companion but a "plug the phone" message appear.
if i try with flashtool the phone are recognized but i can't do noting, if i try to reinstall the kernel a message "connect the phone in flash mode" is displaied.
What can i do?
Please help me
You can do a search and do a ask im proper forum section.
i did it but i didn't find or i didn't understand a solution!
open the back cover
remove the rubber near camera and unplug the pin using pen and reconnect it and start flash tool and connect the phone pressing and holding back key
after flashing kernel reboot phone &start pressing back key quickly after backlight is on
ukyo1234 said:
Hi to all,
i'm trying to install the MiniCM7.
I rooted, installed xrecovery an unlocked the bootloader correctly.
After installed the latest E10_nAa-06 the phone rebooted and the nAa screen appear, than disappear but noting.
The phone doesn't answer.
i can't turn off or turn on the phone.
i've tried with pc companion but a "plug the phone" message appear.
if i try with flashtool the phone are recognized but i can't do noting, if i try to reinstall the kernel a message "connect the phone in flash mode" is displaied.
What can i do?
Please help me
Click to expand...
Click to collapse
Hold power+home button, wait until screen goes black, then immediately press and hold back button, while plugging usb cabel into phone. Then do anything you want, your phone will be in restore mode.
Next time post your question in another section named "XPERIA X10 Mini Q&A"
hi
i have the same problem but i flashed the kernel via flashtools 0.3.5
If i press home and on/off the phone goes off but after few seconds it starts new.
I see the picture from the nAa Kernel and then i get a black screen.
The flashtool identificate the phone with the new kernel but i cant flash a other kernel.
sorry for my bad english
bye bye
use the update service from sony ericsson.
-start update service
-connect your hp using usb to the computer
-press and hold power + home till it restart
-flash back the stock 2.1 version
----> then continue again on the kernel update
Thanks for your help but I have the problem solved differently. My cell phone could not be connected to the Seus. I installed a rom by cwm.
For the people that have flashed a cwm capable kernel:
Just go to recovery menu via home, down on / off and volume
Hi,
I would like to ask you for advice before throwing my X10 mini away and buying something else.
I have had MiniCM7 installed for a very long time (more than a year), and upgraded to all versions without any problem. Today I installed MiniCM9 3.0.2, but I decided to reinstall MiniCM7 because of some problems detected with this version, so I went to SEUS, downgraded to 2.1.1.A.0.6, installed BusyBox, xMiniRecovery, root and flashed MiniCM7 2.2.0 and gapps. I have done it quite a lot of times before.
But, when I tried to reboot onto MiniCM7 2.2.0, my phone was stuck onto Sony Ericsson logo. Here's what I did:
1) Ok, Home+Power and reenter into recovery by pressing back key. No, no luck, it doesn't enter into any recovery.
2) B plan, I'll go to SEUS again. Home+Power, connect USB and keep back key pressed. Nothing, SEUS doesn't recognize anything, but Companion does activate a little popup on my Windows, as if it detects my phone plugged into my computer. No red, yellow, or green lights in the phone.
3) C plan. Flash kernel directly. I downloaded kernel from http://forum.xda-developers.com/showthread.php?p=17674938#post17674938 and used FlashTool. But, again, when I press Home+Power, connect the USB cable and press back key, it doesn't recognize anything, FlashTool is waiting for me to connect something. Antivirus is disabled.
If I keep back key pressed, no SE logo appears; black screen. If I release back key for a little while, SE logo appears and it gets stuck.
Both if I connect it to the computer or to the power socket, no green/yellow/red led appears.
Does anybody have any idea? Everything (cable and phone) were working wonderfully before flashing 2.1.1.A.0.6 for the last time.
Kind regards,
Jordi
Ok,before u try this u should know it will delete everything of phone memory:apps,contacts,etc.
And it removes root and recovery and phone will be like the day u bought it except that bootloader is not touched if unlocked stays unlocked
TRY AT UR OWN RISK
Steps:
1-download sony erricsson pc companion
2-click support zone and choose software update
3-before clicking continue click on repair phone
4-wait till loads and choose phone type
5-concentrate on this one cuz it has 2 methods
5a:if ur phone doesent restart automaticlly just plug usb in computer first then with phone powered off hold the back button and connect the usb cable only let hold when it says u can
5b:if ur phone DOES restart automaticlly remove battery till u reach this step and put back cover bedside till ur done with this method what were gonna do is when we reach this step we quickly plug battery and before it restarts just hold back and insert usb cable.
6-wait to install
7-congratulations unbricking
8-(optional):click the thanks button :xD
Sent from my U20i using XDA
Hi,
Thank you very much for your quick answer. I had never realized the procedure shown in steps 2-4.
But Companion refuses to install it! "It's impossible to install or setup update components of phone sotfware" grrrrrrrrrrrrr Tomorrow I'll try to get another computer and follow your procedure.
Thank you very much
Always happy to help as ive been in such issues alot
Sent from my U20i using XDA
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
SmG67 said:
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
Click to expand...
Click to collapse
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
jordisegurapla said:
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
Click to expand...
Click to collapse
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I've tried that already, doesn't work...
Looks bad, huh???
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I do not know what did I do, but by trying for the 1000th time to do the Home+Power+Back key combination with USB connected and keeping Back key pressed, and pressing and releasing it madly afterwards, while FlashTool was waiting for me to flash MiniCM7, FlashTool has reacted!!!!!! It allowed me to install MiniCM7 again!!!
What happened? I do not know, perhaps I pressed Back key just the microsecond that the hardware needed it.
Thank you very much!!!!
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
SmG67 said:
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
Click to expand...
Click to collapse
Ok, you are right again; FlashTool allowed me to install the kernel ;-) and then, everything else.
Thank you very much, really!!!