Related
so... i search for wifi conections and i find the desired network, i then enter the correct wep password and press conect - it trys to connect for about 5 seconds and the says "disconected"
i have tried using the static ip address method- doesnt work
i have tried hard reset - doesent work
i have updated to 2.1 (about 3 times)- doesnt work
so any ideas?
i will also add that sony erricson support claim that this is not possible
Have you tried another network? Or reboot your router?
Sent from my U20i using XDA App
works well on one other network (and used to on this network!) - and yes rebooted but still not worked!
If it works on another network, i dont think its something wrong with your phone.
Try a few other hotspots
If you are using WPA then switch to WPA2 on your router!
I had a simular problem after going to 2.1 both on my mini pro and the ex's lg gt540, not sure what caused it, but reseting the router to factory and re entering all my settings fixed it for some reason
Use wep
Sent from my U20i using XDA App
I'm having a similar problem with my wife's x10mini. She has it for the past 6 months and has always been able to connect to our home router. Since 2 days ago she has been unable to see the router in her wifi settings and so unable to connect to it. The strange thing is that she can still see all of our neighbors wifi routers, just not ours, that is just 1m away.... I tried manually adding it but it says that the router is out of range.
I have gone through all router settings I can access and the phone still cannot see the router. I've even left the router wide open, without any protection whatsoever and the phone still couldn't see the router, despite seeing all other routers around.
Please give me some ideas to try. I've also formatted the phone and re-installed everything to no avail. I'm getting a bit lost now.
Maybe this can help someone else, my problem was solved by changing the router channel from Auto to Channel 10.
Maybe the router started using a channel that the phone couldn't see/use.
Sent from my GT-I9000 using Tapatalk
Maybe an complete reinstall of the base system would help also try simply turning on and off your wireless and see if it works
I also experience almost all of these bugs but turnin on and off my wireless fixed my problems
Maybe an complete reinstall of the base system would help also try simply turning on and off your wifi and see if it works
I also experience almost all of these bugs but turnin on and off my wifi fixed my problems
Hi just received my GTablet and have installed ClockworkMod v08. Next, I am attempting to install the TNT Lite Rom but I am having trouble connecting to my home router.
The response I keep getting when trying to connect is to the point of "Obtaining IP address.." then it disconnects. I am sure it's not the wireless router but just to be eliminate possibilities, I've even switched off all the security with connect to the router, but the sames results. It keeps trying to re-connect. I can easily connect with my other PCs and printers.
Any ideas? Thanks in advance.
Hello there,
did you ever solve your wifi problem, I am currently running the latest TnTlite, and this just started happening to me as well. It just hangs in Obtaining Ip then it disconnects.... I have never had this problem before in fact was online on the tab last night, now it seems i cannot connect... I will see if I can connect in another location hope nothing happened to the Tab..... BTW I tried restarting as what was suggested but that did nothing for me also....
Are you broadcasting your SSID?
Can you take the tablet somewhere else and try connecting at a Star Bucks, or a library, or something. See if it connects ok there?
Also, if it doesn't connect anywhere. Try flashing a different ROM to see if it is just that one.
I've had the same problem. I do not seem to be able to connect to any wifi that is encrypted with WPA. At work, we are WPA and I cannot connect at all. At home, I have WEP and can connect. I thought it might be something with the wifi settings on the tab, and have searched and searched and cannot find anthing.
By the way, this is my third tab and none of them could connect to a WPA encrypted router. The first two I returned as defective. IF there is an answer, I would love to hear about it.
Also, this is my first android device. I have been messing with Windows phones for a long time...thanks to the great people on this site.
Sorry to hear about your wifi problems. Just to let you know my experiences, I've (in the week I've owned my tablet) run TnT, VegaN and cyanogen (latest of each) and have never had a problem connecting to my home wifi - I do not broadcast my SSID at all and use WPA2/PSK encryption. You both mention WPA - can either of you try WPA2/PSK?
But on saying all of that, if you can't even connect to your wifi point without any security involved, it sounds either:
1) Hardware - faulty tablet but you said you're on your third so that sounds unlikely. Remember, while the tablet supports wifi G/N it does so over 2.4Ghz so if you have a router that only does 5Ghz or is set to work exclusively over 5Ghz, your router will not see your tablet
2) Software related - Have you reflashed your kernel at all? Did you possibly install a kernel (not rom) that does not have wifi drivers installed or something similar?
I hope something above might help you....
I was never able to connect to the wireless router. I shut all the security off, reset the router, rebooted the tablet but still the same results, "obtaining IP address" then it fails and tries again. I could connect to my neighbors Linksys so I know the tablet wifi is ok. I also so know that the router was ok since it had been serving my other PCs & printers for a number of years. It just wouldn't connect to each other.
The problem still persists.
+++++++++++++++++
Running TNT Lite 4.2.1
bevbeng said:
I was never able to connect to the wireless router. I shut all the security off, reset the router, rebooted the tablet but still the same results, "obtaining IP address" then it fails and tries again. I could connect to my neighbors Linksys so I know the tablet wifi is ok. I also so know that the router was ok since it had been serving my other PCs & printers for a number of years. It just wouldn't connect to each other.
The problem still persists.
+++++++++++++++++
Running TNT Lite 4.2.1
Click to expand...
Click to collapse
You didn't answer in your response above, is your router a 5Ghz router or 2.4Ghz? Could the frequency of your router be causing your problem here? Remember the tab only supports 2.4Ghz frequencies
1. if your tablet can connect to your neighbor's router, then problem lies between your router and the tablet.
2. is your router a linksys? what wireless router are you trying to use?
3. are you using mac address filtering? is dchp enabled on the router or by some sort of home server?
4. your tablet can see your router, but for some reaon they cant agree on how to talk to each other. i'm on a linksys wrt54gsv4 and havent had a problem, not with default settings or wpa2 or mac filtering or the custom firmware i eventually installed on it (ddwrt), tomato)
Sent from my GTablet-TnT-Lite using Tapatalk
bevbeng said:
Hi just received my GTablet and have installed ClockworkMod v08. Next, I am attempting to install the TNT Lite Rom but I am having trouble connecting to my home router.
The response I keep getting when trying to connect is to the point of "Obtaining IP address.." then it disconnects. I am sure it's not the wireless router but just to be eliminate possibilities, I've even switched off all the security with connect to the router, but the sames results. It keeps trying to re-connect. I can easily connect with my other PCs and printers.
Any ideas? Thanks in advance.
Click to expand...
Click to collapse
You are ATTEMPTING to install TnT ROM? You dont need the Internet connection, just sideload it then install. Am i Right?
Then after you install the TnT rom, sideload also the Kernel TnT base with wifi fix.
http://forum.xda-developers.com/showthread.php?t=895825
Hope this will solve your problem.
Good luck
powercrazy said:
You didn't answer in your response above, is your router a 5Ghz router or 2.4Ghz? Could the frequency of your router be causing your problem here? Remember the tab only supports 2.4Ghz frequencies
Click to expand...
Click to collapse
I have an older Microsoft 2.4Ghz B/G wireless Router. I'll try to sideload the Kernel TNT base with the WiFi fix.
Thanks for the tips.
Since the original posting I have got TNT Lite installed (using my neighbors router)
bevbeng said:
I have an older Microsoft 2.4Ghz B/G wireless Router. I'll try to sideload the Kernel TNT base with the WiFi fix.
Thanks for the tips.
Let us know if it solve. If not, I think you have defective unit.
Goodluck!
Click to expand...
Click to collapse
Something else occurs to me out of pure ignorance. I'm not sure how Android stores profile information. But I know with both mac and windows I've had occasion where "forgetting" the network and letting the device rediscover it has solved problems.
It sounds like you've been down that road already. However, it does bear asking. It's the more obvious things we often forget to consider.
Well it looked like the tablet needed to be reset a couple of times as i was just online with it... now the tab just froze, shut off and now i cannot turn it on... off to another thread to see what to do now... god i hope this thing is not bricked....any suggestions on what is a good thread would be appreciated... off i go.......
edit: found a thread now to find the internal reset button. thanks to all at xda....
RyuFDAC01 said:
Well it looked like the tablet needed to be reset a couple of times as i was just online with it... now the tab just froze, shut off and now i cannot turn it on... off to another thread to see what to do now... god i hope this thing is not bricked....any suggestions on what is a good thread would be appreciated... off i go.......
edit: found a thread now to find the internal reset button. thanks to all at xda....
Click to expand...
Click to collapse
Try to hold the power button for a long time and maybe it may turn back on. Before doing your last resort (disecting the tablet).
I had a problem with my wifi going into loops when I first got the unit. It would show it connecting/disconnecting/connecting/etc as described in the first post.
I had another router (both the same makes - Linksys WRT54G but different model numbers) so I tested the other router and I connected fine. I haven't gone back to test the first router yet and I am using the 2nd one.
The router I couldn't connect to has DD-WRT micro on it, and I haven't had problems connecting other wireless devices to. The one that is working fine with the g-tablet now has Tomato on it (it is a lower version number which supported Tomato).
Too bizarre... I now have this problem.
I received my gtablet today and installed clockwork mod recovery and vegan-tab ginger RC 1. Or, essentially, I followed the instructions here and got everything working. http://forum.xda-developers.com/showthread.php?t=865245
Wifi worked fine until the evening. Wifi is on, and in the settings under the SSID of my wifi network, it says Obtaining IP address for a minute until it says Disabled, network in range. I've done some common trouble shooting, like restarting, turning wifi off and on, forgetting the network and reentering password. That didn't work. My cell phone has a mobile hotspot feature and the gtablet CAN join that. I wonder what gives... I hope someone can help.
(This could be just coincidence, but it's about when I powered up my desktop computer. The desktop connects to the internet through a DMZ router that has a wired connection to the wifi router in another room. The desktop is now off and the gtablet still has this problem.)
Ok. Resetting my router fixed it. I never thought that my router could just "dislike" one particular device. I thought for sure something had to be wrong with the device. Forgive my ignorance!
G Tablet Wifi
I do not transmit my SSID and this has never been a problem with any of our laptops or netbooks. When I first received my G Tab and tried to connect to my network, even though I had entered the SSID and Passphrase correctly, it still would not connect. As soon as I set my wireless router to transmit the SSID the G Tab connected without any problems.
This is the first time I've encountered a problem of this nature. Comments?
This is what worked for me. I posted this in a similar thread as well.
Hey, I had WiFi connection issues too. I just got a Viewsonic G-Tablet with the Android 3.0 OS and have a D-Link DI-524 wireless router. It could see router and would try to connect, but would cycle and never connect. I could try to connect to other available networks in the area. It connected fine to an unsecure network, and when I tired to connect to secure networks there was a place where I could enter a network key/password. However, I noticed this option was not available on my network when I tried to connect. I reset my router which did not help. I then chose the option to add a network on the tab. This worked!! I was able to enter the key from the add a network option. I then told the "bad" connection to be forgotten. Hope this helps someone else, as I had looked on the internet for awhile for an answer. I was about to buy a new wireless router too!! Oh, I am using WEP too.
edit: ok when I power my tablet back on the same issue was happening. This time I could enter a network and the cycling still contiuned. I even forgot and re-entered the network. The fix this time was to reboot the tab. However, my internet has been acting up lately so IDK.
Hi, is anyone has the same problem? When I'm connected at home to my Tenda router (WIFI b/g/n) after cca 30 min. my phone WIFI stops sending and recieving data, Skype is offline, etc... but WIFI in phone is stil switched on. After I switch WIFI off and back on (on my Samsung, not on my router), everything works good for a while and after cca 30 min. is situation the same. Is there in Samsung any WIFI sleep mode or something like that? Or some settings, which is not visible? Any other suggestions? Sorry for my poor English. Thanx in advance.
I'm having the same problem. But I did a factory reset and it works fine afterward.
And just few hours ago, I encountered this problem again. What did to get this error was, I pressed "on samsungapps" and it failed to update and thus results wifi connection stopping. What about you? Also my Kies air is not working.
are you guys sure you have wifi sleep policy set correctly? just to be sure, settings, wireless, wifi, menu button, advanced, wifi sleep policy to NEVER.
Yes. And also even if i manually disconnect and reconnect the wifi back. The data still doesn't come in. It is stated there as connected but no data at all.
Somehow Wifi keeps searching every few seconds, even thought it's connected.
This is bound to cost in battery life too.
I have reseted router to default settings, disabled n mode, disabled security (only mac filtering is on), disabled all unnecessary features and PROBLEM IS SOLVED !!! Thanx God Tomorrow I will experiment with router settings to know, what was causing this error ;-)
Well at least u're connected, I'm facing the same problem as the thread starter. No data flow at all. Browser showing me offline msg. I had the same problem on the 1st day with the phone after I woke up. previously playing with most of the default aps. So i'm not sure what went wrong, did a factory reset and it works fine.
Until, few hours ago, I tried my kies air which didn't work. Browser couldnt load the address given. And I thought i had an outdated kies air, so i went to click on samsungapps, which failed to update me. At that point the wifi is still working, i leave my phone for about 30 mins, and when i came back. The same problem which happened on the 1st day came back. I was hoping to find an answer here so I didnt do the factory reset it. On another note, the phone wifi works after restart, but wouldn't last.
Edit: The wifi works after i resetted my modem to default. oh well. at least that solved it.
lukecz said:
I have reseted router to default settings, disabled n mode, disabled security (only mac filtering is on), disabled all unnecessary features and PROBLEM IS SOLVED !!! Thanx God Tomorrow I will experiment with router settings to know, what was causing this error ;-)
Click to expand...
Click to collapse
Hi,
Did you find out what setting was causing the connection issue? I also have this problem with my Tenda router. I thought it might be the wireless N, but disabling that doesn't fix it. I have a wireless distribution system set up with other tenda routers so didn't want to disable all the settings to troubleshoot if i can help it!
Thanks
spen2 said:
Hi,
Did you find out what setting was causing the connection issue? I also have this problem with my Tenda router. I thought it might be the wireless N, but disabling that doesn't fix it. I have a wireless distribution system set up with other tenda routers so didn't want to disable all the settings to troubleshoot if i can help it!
Thanks
Click to expand...
Click to collapse
I have the same problem, my router is N and the conection between SGS2 and my router is bad. Any idea?
Same problem here, I'm running WZR-AGL300NH in access point connected to my Ubuntu Server. Everything else works in the house just fine but SG2 stops transmitting data after a while.
I recently upgraded to KF1 firmware (and unknowingly wiped out whole phone, being on the bleeding edge and that didn't seem to help.
I would very much appreciate all tips because this problem is very annoying!
Additional Info:
- Buffalo is running latest firmware
- Authentication WPA2-PSK
- Encryption AES
paranoidi said:
Same problem here, I'm running WZR-AGL300NH in access point connected to my Ubuntu Server. Everything else works in the house just fine but SG2 stops transmitting data after a while.
I recently upgraded to KF1 firmware (and unknowingly wiped out whole phone, being on the bleeding edge and that didn't seem to help.
I would very much appreciate all tips because this problem is very annoying!
Additional Info:
- Buffalo is running latest firmware
- Authentication WPA2-PSK
- Encryption AES
Click to expand...
Click to collapse
Same symptoms here. Cisco DDR2200. WPA2 PSK. Haven't tried fiddling with the router yet.
This seems to be a common problem. Anyone knows of a definitive fix?
Bump...I have the same problem and the issue persists even after i reset the phone
Sent from my GT-I9100 using XDA App
Glad I found this, thought it was the ROM I had flashed to the phone (which is VillainROM)
I keep losing connection from my phone via wifi like everyone else in this thread
edit: I've just assigned my phone an IP address via my routers settings and I can connect to the net again
Also when it wasn't working, I couldn't ping the phone. When I assigned the IP just now I still couldn't ping it.
When I did a tracert to it, I could get to it when the IP was assigned and when it wasn't.
I have no removed the assigned IP for the phone from the router. Wifi connection is still working after disconnecting/reconnecting wifi on the phone.
I can also now ping the phone, where as before it was getting timeouts.
Also when it wasn't working the first time when I did a tracert it was showing up as HPsomething (didn't make note of the numbers)
this time when it is working it's just showing up as the IP address when doing a tracert.
Another update:
Just checked my printer, it has an IP address manually set on it, which at one stage when the phone wasn't working for internet it had the same IP as the printer, hence when tracert'ing it I was going to the printer instead of the phone and getting the HP etc back.
When it wasn't working at that time and looking at my routers DHCP list, it had the MAC Address of the phone against the IP that the printer has....
So I've got some issues with how my own network is setup ^_^ which looks like is causing me grief.
So the issue is with DHCP? Setting a static IP fixes it? I'll have to try, but I doubt this is a problem with the network, as all my other devices use DHCP without this problem.
I have the exact same problem!!
It's really annoying.
i was having problems with wifi too.. it keeps scanning and checking, etc, signal dropping for no reason..
fixed mine..well for me it worked
backup ur phone ( i dont take responsibility if ur phone catches fire or dies or chases u around )
u need to be rooted
download FXR WiFi fix and rescue from market
and just run the app.
now my wifi signal stays constant speed and i get good speeds
alternatively try
WiFi Fixer
both of them will cause high battery usage..i think since it keeps the signal at maximum.. so only enable wireless when i need it or use juice defender or green power.
greenpower seems great. using this at the moment
So my WiFi has been working fine on my prime connecting to any network till yesterday. I went to work, connected to the WiFi network, everything working fine. Then I disconnected from the network and tried to reconnect and it wouldnt connect. All I get is it saying obtaining ip address. I went to my girls after work, same issue there, sees the network but all I get it obtaining ip address and it never goes past that. It does connect to my sensation hotspot though. I hard reset it, even factory reset it and still have the issue...any ideas?
Sent from my HTC Sensation 4G using xda premium
Ever try resetting the router?
I would never have reset over it.. not without rebooting routers/modems first and it sounds like you didnt try this. I get this issue now and then - rare - and a router reboot always fixes it. I never have to resort to drastic stuff like phone or tablet resets. The fact it can talk to your phones hotspot - not router related - even more signals to the router as first place to look.
Lock-N-Load said:
- even more signals to the router as first place to look.
Click to expand...
Click to collapse
I agree....this will work for when he's at his "girl's", but the bigger problem is the office network. That can't be rebooted at will.
Best suggestion I have is to go into the Adanced mode, and where an option "modify Network"...choose that....sometimes just hitting SAVE works, sometimes I re-enter the WEP key and hit save.
In worst case, you could say "forget network" and try starting from scratch....
Good luck,
Bob
You sure your work doesn't do any sort of MAC filtering? Maybe something adaptive?
Dear All ,
I have been suddenly encountering wifi connection issues with my S3.
It refuses to connect to any router unless i am very near to it.
There is no problem with reception as the phone can detect the wifi and has 3-4 bars
If i try connecting while far away from the router to a detected network, it just gets stuck on "connecting.."
If i connect while near the router and then walk away, remains connected but I have no internet access..
Things I have tried:
1-cycling wifi on/off , reboot phone, reboot gateway
2-turning off wifi power saver from service mode *#0011#
3-flashing a different non stock rom after doing a wipe/factory reset.
4-searched extensively for three days with no avail
If any encountered such a problem before and was able to solve it, your help is highly appreciated.
marwanhamed said:
Dear All ,
I have been suddenly encountering wifi connection issues with my S3.
It refuses to connect to any router unless i am very near to it.
There is no problem with reception as the phone can detect the wifi and has 3-4 bars
If i try connecting while far away from the router to a detected network, it just gets stuck on "connecting.."
If i connect while near the router and then walk away, remains connected but I have no internet access..
Things I have tried:
1-cycling wifi on/off , reboot phone, reboot gateway
2-turning off wifi power saver from service mode *#0011#
3-flashing a different non stock rom after doing a wipe/factory reset.
4-searched extensively for three days with no avail
If any encountered such a problem before and was able to solve it, your help is highly appreciated.
Click to expand...
Click to collapse
I haven't encountered this specific problem before, but I have had other problems with my S3 and WiFi. It turned out the problem was my router, which was in 5ghz mode. If you have a 5ghz router, try to switch it to 2.4ghz.
Something else you can try is to change your modem and/or kernel. Those 2 both have something to do with WiFi, so maybe it'll work.
Again, I haven't encountered your specific problem myself, these are just some suggestions.
Sent from my Galaxy S3 with Tapatalk
marwanhamed said:
Dear All ,
I have been suddenly encountering wifi connection issues with my S3.
It refuses to connect to any router unless i am very near to it.
There is no problem with reception as the phone can detect the wifi and has 3-4 bars
If i try connecting while far away from the router to a detected network, it just gets stuck on "connecting.."
If i connect while near the router and then walk away, remains connected but I have no internet access..
Things I have tried:
1-cycling wifi on/off , reboot phone, reboot gateway
2-turning off wifi power saver from service mode *#0011#
3-flashing a different non stock rom after doing a wipe/factory reset.
4-searched extensively for three days with no avail
If any encountered such a problem before and was able to solve it, your help is highly appreciated.
Click to expand...
Click to collapse
I'm having the same problem for about 2 months now, it's driving me crazy, if anyone knows how to fix this please let us know! Thank you in advance.
AS the guy above you suggested try changing your modem and if that fails try a new kernel which should sort out the problems you are having. Or as he also suggested try your router and make sure it isnt in 5ghz mode only.
Try logging into your router's configuration and changing the wireless network channel from auto to a manual setting (e.g. 9 or 3). The only wifi problems I ever had with my S3 were (misconfigured) access points and routers.