Hello everybody,
First of all ı apologize for my english if ı mention wrong
Nowadays ı m planing to buy HTC Amaze 4g but my friend told me like that when he was using Htc Amaze the main body is starting to play with time inside the backplate.He means you can feel like springy.
So anybody have as a problem like this?
It is just the way the phone is designed. It isn't a back plate like you might think. Other than a little at the bottom the "back plate" is the entire silver part around the screen - sides, top, back and the black at the bottom. The screen glass sits up in the middle of it. Therefore there is bound to be a little "springy-ness" to it due to tolerances. However I don't notice it during normal use at all. You can feel it if you pinch it front to back. If it was bothersome I'd guess a thin shim of paper would take up any tolerance slack.
Thanks for your answer.I think my friend is so sensitive.
in any case ı want to get my amaze as soon as possible
Related
Hello,
unfortunately my stylus cap came off.
Now the longer part of the stylus is stuck in the XDA :-(
Any ideas how to get it out again?
many thanks
golf
if you cant put the upper part into the xda and screw it a bit on and then pull it out
then maybe a longer metal or what ever stick with the same size thread
would be able to get screwed into the pen and then you can pull it out
Thanks for the very quick reply.
When it happened for the first time I was able to "reconnect" screwing the top part on.
But now it's not deep enough. I just doesnt connect, because the main part slid in to far or the thread doesn't grip :-(
I called O2 and they said I would have to send it in...
Very anoying...
well a long screw with the same size and the top would be able to connect would it not ?
You need to get something with the same thread as the top half but longer, then just screw it in and pull the lower half out, if it is broken off then thats a different story.
Thanks folks.
I will stop by at a DIY shop and see if I can find a long screw somewhere...
cheers
golf
I had this happen to me. I put some Krazy Glue in the top half and then pushed it onto the bottom half - waited about 20 sec, then it pulled out without a problem. My issue was the both screw threads became completely stripped.
Jon.
I used the handle end of a small artist's paint brush.
The tapered, plastic shaft was just the right size to push into the stuck portion of the stylus.
Obviously you'll need to hunt around for the right size, but most households will have something similar.
Thank you, the screw did it
I am happy to inform you that with your help yesterday I managed to release the stylus.
A long screw did the the trick for me easily.
Now the only problem left is the unstable screen color, but that's something I have to live with...
thanks again
golf
i need help since im on a kind of a hurry.
i have an x10a, unlocked rooter and cm6.1.2 i think, i have a terrible battery life with the 3g data network activated now.
because of that i need to know how to optimize the battery and the phone itself as soon as possible cuz i just got a white x10 for my gf and i want it to be froyo or gb and since she is a USER i want to give her a fully fuctional phone with a decent battery life (vs a bb lol easy).
i havent done a big search but the help its welcomed, i need to fix those phones
EDIT: there is a film over the screen of the xperia, that is an original screen protector or what? i want to change it since its pretty battered by my pocket but i dont know if its something important or just a screen shield
its a plastic film find a corner and gently pull it up and behold the pretty glass underneath
leo5111 said:
its a plastic film find a corner and gently pull it up and behold the pretty glass underneath
Click to expand...
Click to collapse
thanks, happy to know taht my screen its ... not that screwed hahaha
looks like im going to find out hte best wway to get the phone work right damn
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
SecUpwN said:
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
Click to expand...
Click to collapse
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
richyrocket said:
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
Click to expand...
Click to collapse
Thank you so much for stating this, exactly what I was talking about! Kind of a small release to hear I didn't buy faulty hardware. Do we have other readers here who can confirm that this behavior is normal?
I'll head out to the phone store today to double check. Still, does an app exist to check for hardware failures?
Yes no faulty equipment, it is normal on every single Evo.
( Don't ask for help as I couldn't care if your phone explodes, eh)
flashallthetime said:
Yes no faulty equipment, it is normal on every single Evo.
Click to expand...
Click to collapse
You just saved my whole HTC experience. Thank you soo much! How come this is the case on every EVO? Isn't that something draining the battery?
No it is actually bleeding from the main screen, I guess there's a small gap between the search button and the screen
( Don't ask for help as I couldn't care if your phone explodes, eh)
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Use your phone in the dark. Watch until soft buttons stop glowing. See the light behind the search button?
Mine has it too.
Sent from my HTC EVO 3D X515m using xda app-developers app
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Turn the backlight of touch buttons off using kernel tuner and keep screen on, you will notice light behind search key.
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
dessolator666 said:
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
Click to expand...
Click to collapse
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
SecUpwN said:
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
Click to expand...
Click to collapse
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
dessolator666 said:
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
That would actually be the coolest contribution I've seen in a ling time! Are you really willing to do that for our EVO community? If you did, you'd be our king.
Don't worry, it's on every EVO 3D. From GSM to CDMA.
The light bleed is from the screen back light. It does give the phone a cheap feel sometimes, but it's a common problem.
It's not as prevalent on cm10 with inverted gapps
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
flashallthetime said:
It's not as prevalent on cm10 with inverted gapps
Click to expand...
Click to collapse
How come?
SecUpwN said:
How come?
Click to expand...
Click to collapse
Inverted gapps has black backgrounds so the screen bleeding is reduced
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
---------- Post added at 10:56 PM ---------- Previous post was at 10:51 PM ----------
I can drastically reduce screen brightness which helps, there's still some bleeding
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
dessolator666 said:
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
HermanV0929 said:
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
I'm sure it can be done... because you have to do pretty much exactly that when replacing the LCD or digitizer
Yeah,
I love it first phone i've had in a long time without the dumb carrier logo on the front!!!
Beautiful phone...Back is even nicer with that deep rich 3D look to it coming through the lacqured back..of course they had to put the logo back there...but at least it doesn't say AT&T just the globe...
SD/SIM slot cover feels cheep...everything else very nice...whish it would have had a little metal trim around headphone jack, would have classed it up a bit
only negative is out in the sunlight you can really see the digitizer dots or whatever they are called
way to go LG i thing this may be your first real hit in a while
Just a quick question. Anyone else have an issue with their screen cracking? My P9000 has developed a crack over the led. I didn't drop, knock or bump the phone. I've emailed support for advice. I'll keep this forum posted.
Update got a very prompt response. Two sentences
"Good day!
we are sorry to hear that, but screen will not crack by itself. it may have some physical damage on it."
No details of how to get a repair, that's it! Not the best customer service. I've replied enquiring about service centres, costs etc. and will update the post when I get more info. There are a few posts asking for similar details re. Screen replacement so the info will be useful for the community.
actually it's strange to think that a screen can brake by itself , can you post some pictures?
elephone customer care have already proved it's lower quality service . i don't know where you live but best solution imho is to give the phone to a local cinese phone repair shoop , here in my city there are a couple that repair - fix phones for low money and they also provide spareparts that arrive very quick and at low price thanks to it's black market channel, try to search one
I agree it's very unusual that the screen would break in this way, but I'm really very careful with all my devices and this has never happened before.
If Elephone say that this cannot happen then I'm not going to quibble, I'm more interested in repairing the phone. Sending it back to the seller for repair will be an interesting, long and probably prohibitively expensive process, but I'll make enquiries.
In other news Elephone are still working on a new ROM for the device, I took the opportunity to ask supplementary questions in my email :laugh: so the chatter on the forums about the 19/04 build being the last one can abate for a while.
The crack in question. Doesn't impair functionality and there's are no signs of impact
The only replacement display I found on the Web is this one https://m.aliexpress.com/item/32673463140.html Unfortunately I have no clue if this is an original display and if could place it on my phone by myself
Your phones has physical damage along the bottom side of the metal frame can clearly see where its been scraped. You sure it didn't drop or get dragged along something while face down? Hopefully there's an OEM replacement as its just the glass that seems to be damaged not the LCD
Thanks I wouldn't know how to even begin the repair but it's useful info.
I had a similar small crack appear on mine which had not been dropped I assumed it had been knocked whilst in my pocket, But then today i put my phone in my pocket to drive and collect the kids when i got to the school i had 3 additional cracks I assume its something to do with the size of the screen and it not flexing.
The new cracks now make it pretty tough to use the phone as they are affecting the touch functions, once i can unlock it i will take some photos to post.
Banathe said:
I had a similar small crack appear on mine which had not been dropped I assumed it had been knocked whilst in my pocket, But then today i put my phone in my pocket to drive and collect the kids when i got to the school i had 3 additional cracks I assume its something to do with the size of the screen and it not flexing.
The new cracks now make it pretty tough to use the phone as they are affecting the touch functions, once i can unlock it i will take some photos to post.
Click to expand...
Click to collapse
Thank you. I'd almost convinced myself that I must have knocked the phone.
Events have taken a new turn. The left hand side of the screen now creaks and pops when you press on it. If I press sufficiently hard enough it stops creaking and popping, almost as if it is correctly seated again only to literally and audibly pop out again 5 minutes later.
I will post a video later, and will be contacting elephone with evidence that there is a design flaw with the device. I'll keep this forum updated on my progress.
thats weird thats where my spontaneous crack started images attached, the bottom one is under the glass but i think was the cause of the left side one.
Adding images as attachments as well given the URLS don't seam to be showing correctly.
Mine also has a minor crack on the screen, it's in a case and has not been dropped. There is no damage to the frame at all, I'm guessing it's from being in my pocket. The phone obviously isn't as strong as mainstream manufacturers. My crack is very faint in the top right corner and you really have to look at it in a certain light to see it.
If it gets worse, I'll buy a new phone (One Plus 3) and not look at this device again
Sent from my P9000 using Tapatalk
Mine broke in my front pocket without impact. It was the aluminium frame that was bending and must have cracked under the stress. In hindsight I should have started putting the phone in my pocket the other way around. Ha ha!
YorkshiresSnipper said:
Mine broke in my front pocket without impact. It was the aluminium frame that was bending and must have cracked under the stress. In hindsight I should have started putting the phone in my pocket the other way around. Ha ha!
Click to expand...
Click to collapse
I note the replacement screens have come down in price I may have to have a go at a repair.
Sent from my Z2 Plus using Tapatalk