Unbranding Titan ASIA to Europe operator by ansar - HTC Titan

Hi,
I will have my hands on a Titan for a few days or week about and
will try to unbrand ASIA branded in order to run a Europe operator ROM
Did you have any flashing issues up to now with Europe or ASIA ROMs?
Regards, ansar

hey ansar, i have not tried to flash any other roms on my usa at&t titan yet...but that sounds like really good news for us that you are getting a titan!!!
let us know how your progress goes after you get it. would really like to get custom roms on this bad boy!
thanks

If you could get an AT&T ROM flashed on a European Titan, that would be great. I desperately need English (US).

Great news we have a developer working on the titan.
I would prefer this type of post to be in the general section, as the read before sticky states (No questions in the development section). Once sorted, please post the results in the development section.
If you have any issues please feel free to PM me.
Thanks
Your friendly HTC Titan moderator

ansar.ath.gr said:
Hi,
Did you have any flashing issues up to now with Europe or ASIA ROMs?
Regards, ansar
Click to expand...
Click to collapse
Yes.
I have a a UK Titan here in Singapore, and there is a known bug which means that Contact Cards are not referenced when receiving an incoming call with a +65 prefix. This problem is not present on the Taiwan models.
So, our friendly Football sent my the Taiwan ROM for me to try flashing.
I can tell you that no chance with RUU. So next step is goldcard method.
However, problem is my Y-cable did something nasty and blew out the screen on my Titan The unit still works, just cannot see anything on screen. Its been in for repair since the end November and I still don't have it back to try again.
So yeah, very interested to see if you can cross-flash, and how.

Really look forward to method for successful flash!!

Idea....
if anyone backup a unbranded rom utilizing this and restore over a branded rom? its the same hardware why not try
if anyone post a unbranded backup i want to try because my titan still on warranty, and i doubt my network operator is going to check if i tried to install another software.

Hi,
I have received my HTC Titan today, unfortunately Its branded do Vodafone Ireland.
Today I'm gonna try to unbrand my phone with the xboxmod method, as you can see here
Does anyone have already tested this in the HTC Titan?
Let's hope this works.

NuMbErSeVeN said:
Hi,
I have received my HTC Titan today, unfortunately Its branded do Vodafone Ireland.
Today I'm gonna try to unbrand my phone with the xboxmod method, as you can see here
Does anyone have already tested this in the HTC Titan?
Let's hope this works.
Click to expand...
Click to collapse
did it work?

abo.saud said:
did it work?
Click to expand...
Click to collapse
Yes, today I have successfully unbranded my HTC Titan. I made a Y cable and the goldcard with my Micro SD (you can find more info here). I have used this ROM IMG_Eternity_HTC_Europe_1.08.401.02_Radio_16.23.02.09_2_16.24.00.23U_Signed_ETERNITY_RELEASE (you can find it here) and I renamed it to ETERIMG.nbh and then pasted it to the root of the card. After that, you just have to wait and enjoy.

NuMbErSeVeN said:
Yes, today I have successfully unbranded my HTC Titan.... After that, you just have to wait and enjoy.
Click to expand...
Click to collapse
Can you tell me - once you have goldcard with image - do you go into bootloader and then connect cables, or connect cables and then enter bootloader?
Nothing happing for me - except when connected I do not get the "serial" on bootloader screen...but nothing else happens For instance, does the bootloader screen say USB or anything?
Any more detail you can provide is appreciated.
EDIT: also no response in USB host mode (where you get the phone/laptop grahpic)

twisticles said:
Can you tell me - once you have goldcard with image - do you go into bootloader and then connect cables, or connect cables and then enter bootloader?
Nothing happing for me - except when connected I do not get the "serial" on bootloader screen...but nothing else happens For instance, does the bootloader screen say USB or anything?
Any more detail you can provide is appreciated.
EDIT: also no response in USB host mode (where you get the phone/laptop grahpic)
Click to expand...
Click to collapse
You can be into bootloader first (Vol down + camera + power) and as soon you connect your USB device with your image, the phone will start immediately the updade.
If the phone don't start the update, its because something is wrong with the cable or the goldcard.

NuMbErSeVeN said:
You can be into bootloader first (Vol down + camera + power) and as soon you connect your USB device with your image, the phone will start immediately the updade.
If the phone don't start the update, its because something is wrong with the cable or the goldcard.
Click to expand...
Click to collapse
Hmm yeah it gets stuck on screen saying "Loading..." grr

Hi, I have here Titan branded with German Vodafone. I have made goldcard and copied the eterimg.nbh file to the root of sd card. But when I plug the double usb cable with the goldcard to the phone the "no image file" is written for split second on the screen. I have tried to create goldcard with xtc clip and with the goldcardtool but the same problem. I switched phone into bootloader by pressing vol- + camera and power. Can You help me? Thanks for reply.
B.R.
Karel
---------- Post added at 06:18 PM ---------- Previous post was at 06:14 PM ----------
twisticles said:
Hmm yeah it gets stuck on screen saying "Loading..." grr
Click to expand...
Click to collapse
This happened to me when I plug the double usb cable with no sd card or with no goldcard. Make the goldcard again and try it.
B.R.
Karel

Unbrand AT&T Titan
Has anybody tried this to unbrand an AT&T Titan successfuly using an unbranded european rom? I may try this myself. Thanks.
Dan

sunhi3man said:
Has anybody tried this to unbrand an AT&T Titan successfuly using an unbranded european rom? I may try this myself. Thanks.
Dan
Click to expand...
Click to collapse
Good question! I bet a lot of us in the US want to unbrand our phones just like I did with my HD2. Whoever is working on it, keep going. There's a lot of us waiting patiently.

Hi,
The ROM is at final testing and will be uploaded soon
Thnx 4 commenting!!
Regards, ansar

ansar.ath.gr said:
Hi,
The ROM is at final testing and will be uploaded soon
Thnx 4 commenting!!
Regards, ansar
Click to expand...
Click to collapse
This is great news!! just wondering though.. will we still need to do it through the gold card method?
I am actually looking forward to unbrand from eu to asia version

ansar.ath.gr said:
Hi,
The ROM is at final testing and will be uploaded soon
Thnx 4 commenting!!
Regards, ansar
Click to expand...
Click to collapse
Awesome. I hope this works with the U.S. AT&T Titan. Keep up the great work, can't wait to try it.

I DID IT!
Finally, got the Taiwan ROM 1.10.709.01 flashed onto my EU (UK) Titan.
After the flash (release 7720) I got the 7740 and 8107 updates to give me:
OS 7.10.8107.79
FW: 1600.2200.20302.709
HW: 0002
Radio: 16.23.03.17_16.27.00.23U
Radio HW: 2.122.0.D4
Bootloader: 2.3.160015.3(134621)
Although my UK Titan was unlocked/unbranded, there was a weird bug with caller contact cards not showing on incoming calls if the number was stored with international prefix. (There was also a bug that meant no contact name was shown on incoming text messages if there was NO international prefix. Basically- the phone was handling calls and messages differently, and often I only got the number displayed )
SO yeah, now that is fixed
After the flash, the first welcome screen is in Chinese, so you select the bottom right box (for "next") and the next screen gives you the chance to select English. After the reboot, everything seems to work as it did on the EU ROM, except that Connected Media app from HTC is still labelled in chinese, not english But if that is the only noticeable difference, I can live with that
andylhchen said:
This is great news!! just wondering though.. will we still need to do it through the gold card method?
I am actually looking forward to unbrand from eu to asia version
Click to expand...
Click to collapse
Totally possible with Goldcard method already
I will add that what took me so long (I had the ROM in late november!) is that firstly my home-made Y-cable blew my screen and the Titan went for vacation at HTC Service Centre for six weeks.
Then I kept making my Goldcard, trying all sorts of different methods to get it to work, but my phone kept getting stuck on "Loading..." screen.
I had tried reading the CID from my SD Card via my Android HTC Flyer with the Goldcard Tool, and a WM6 HTC Touch I had lying around with the PSAS tool, and weirdly the CIDs were different (same SD Card).
I tried using Hex editor to write the goldcard to the disk, but it kept coming back as not formatted...
Eventually, I downloaded an app on my tablet called "Goldcard Helper" which showed up TWO CIDs on my tablet...one for internal storage I guess, and one for my SD Card...thus, the goldcard tool was only giving me CID for my internal storage and I was trying to make that into a goldcard on another SD...
So anyways, when I finally established the correct CID, I used the online tool to generate the goldcard, then used Goldcard Tool to write it to the SD card. Then copied over the TW ROm, labelled it ETERIMG.nbh and plugged it in...no dice!
I had read someone that some female to female USB adapters are cross-over, so as a last resort I tried another f/f/ USB adapter...and WHAM flash starts.
Bit of a panic moment when the phone rebooted a few minutes in, but that seems to be part of the install process. Then it just a matter of waiting until the phone reports "success".
Sweeeeeeeeeeeet
---------- Post added at 03:19 PM ---------- Previous post was at 03:03 PM ----------
ansar.ath.gr said:
Hi,
The ROM is at final testing and will be uploaded soon
Thnx 4 commenting!!
Regards, ansar
Click to expand...
Click to collapse
Out of interest, what is special about the ROM you are developing?
Seems that NuMbErSeVeN has managed to unbrand with a goldcard ROM flash...and just today I managed a Asia ROM flash onto EU Titan...
If all you are looking for is to unbrand an Asia Titan to an EU one, why not just try a goldcard flash with one of the stock ROMs? If it works one way, why should it not work the other way?!?

Related

Vario II crashed

Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked

[Q] T-mobile HD2 Update MR Software (Version 3.14.531.1), What is it?

T-mobile HD2 Update MR Software (Version 3.14.531.1), What is it?
Today T-mobile release a new software update. Does anybody know what it is for?
I assume if you have a rom installed it is no good. I am running Energy Rom, and Radio 2.15.50.14, so I am assuming updating would be a bad idea.
yeah has anyone installed it and what are the benefits of it?? I want to know b4 installing...
You may get better answers over in the TMOUS HD2 forum on this
Features of the 3.14.531.1 update
I also had the same question - what is it that changed with the new HTC HD2 ROM? I spent a lot of time searching, and found this:
Pasting the text below, just in case that link dies (I hate it when that happens):
[pasted from phonesreview uk on 10/22/2010]
==============================================
For all you T-mobile HTC HD2 smartphone users out there who have been waiting for an official software update to land, you’ll be happy to know that today is the day you have been waiting for as T-Mobile is to release software update version 3.14.531.1 to the HTC HD2.
According to an article over on Tmonews, the new software update from T-mobile will deliver several fixes along with stability improvements and access to new apps like Amazon MP3 and Shazam. As for those bug fixes…
The new software update will fix such stuff as slow browsing when on Facebook, the inability to delete Gmail messages in the preview screen, Twitter errors, SMS being delivered to the wrong person, and the white screen whilst browsing the net, the inability to hear Visual Voicemail, unable to unlock the device, unable to unlock the HTC HD2 with correct password, and the lack of a space bar on company directory keyboard, and finally the speakerphone doesn’t work after using the Call Assist app to call 611.
HTC HD2 user can download the new software update by visiting t-mobile and following the instruction; however T-mobile will issue a notification by text to HTC HD2 users when the update is ready, which should be today the 19th of October so keep an eye on your text messages and let us know how you get along.
xxandy said:
I also had the same question - what is it that changed with the new HTC HD2 ROM? I spent a lot of time searching, and found this:
Pasting the text below, just in case that link dies (I hate it when that happens):
[pasted from phonesreview uk on 10/22/2010]
==============================================
For all you T-mobile HTC HD2 smartphone users out there who have been waiting for an official software update to land, you’ll be happy to know that today is the day you have been waiting for as T-Mobile is to release software update version 3.14.531.1 to the HTC HD2.
According to an article over on Tmonews, the new software update from T-mobile will deliver several fixes along with stability improvements and access to new apps like Amazon MP3 and Shazam. As for those bug fixes…
The new software update will fix such stuff as slow browsing when on Facebook, the inability to delete Gmail messages in the preview screen, Twitter errors, SMS being delivered to the wrong person, and the white screen whilst browsing the net, the inability to hear Visual Voicemail, unable to unlock the device, unable to unlock the HTC HD2 with correct password, and the lack of a space bar on company directory keyboard, and finally the speakerphone doesn’t work after using the Call Assist app to call 611.
HTC HD2 user can download the new software update by visiting t-mobile and following the instruction; however T-mobile will issue a notification by text to HTC HD2 users when the update is ready, which should be today the 19th of October so keep an eye on your text messages and let us know how you get along.
Click to expand...
Click to collapse
It will also **** up some stuff, while fixing others.
No Bluetooth stack fixes...
Its horrible...I'm having the worst connections to apps like Omarket, Marketplace, Slacker Radio...The Wifi will not stay connected...The only thing working as far as connections is the internet.
edit: Everything's working now except the Facebook app.
hi... does anyone know?
i buyed my hd2 t-mobile unlocked and i'm using it in argentina with "Claro Argentina"... the question is... if i change the rom in this Leo... it's going to be locked again to be used only with T-Mobile?
i don't want to blow it!
thanks!
cainmako said:
hi... does anyone know?
i buyed my hd2 t-mobile unlocked and i'm using it in argentina with "Claro Argentina"... the question is... if i change the rom in this Leo... it's going to be locked again to be used only with T-Mobile?
i don't want to blow it!
thanks!
Click to expand...
Click to collapse
no. Once a phone is network unlocked it cannot be locked again.
cainmako said:
hi... does anyone know?
i buyed my hd2 t-mobile unlocked and i'm using it in argentina with "Claro Argentina"... the question is... if i change the rom in this Leo... it's going to be locked again to be used only with T-Mobile?
i don't want to blow it!
thanks!
Click to expand...
Click to collapse
yes, it will be locked again! But, there is no reason why T-mobile will not request an unlock code from HTC on your behalf. Usually it takes 24-48hrs
erezgati2 said:
yes, it will be locked again! But, there is no reason why T-mobile will not request an unlock code from HTC on your behalf. Usually it takes 24-48hrs
Click to expand...
Click to collapse
Not correct sir, ons your device is bean unlock't and you upgrade/downgrade your Rom it will not be locked again.
DensoYamaha41 said:
T-mobile HD2 Update MR Software (Version 3.14.531.1), What is it?
Today T-mobile release a new software update. Does anybody know what it is for?
I assume if you have a rom installed it is no good. I am running Energy Rom, and Radio 2.15.50.14, so I am assuming updating would be a bad idea.
Click to expand...
Click to collapse
Why you say it's a bad idea...because the official is no good or because you can damage the phone this way ? I went from omega to the 3.14.531.1 and I experience many problems freezes restarts etc ...I think the update damaged the phone (although it was successful)
yorgosb said:
Why you say it's a bad idea...because the official is no good or because you can damage the phone this way ?
Click to expand...
Click to collapse
no, because it would remove the rom he was using, which he didnt want.
I went from omega to the 3.14.531.1 and I experience many problems freezes restarts etc ...I think the update damaged the phone (although it was successful)
Click to expand...
Click to collapse
you probably left hspl installed, 3.14 plus hspl = "many problems freezes restarts etc"
Ι am no expert but I am sure I replaced HSPL with SPL 2.08
Still I experience all these freezes and restarts with both 2.13.531.1 and 3.14.531.1 versions (in 3.14.531.1 it even freezes when you insert the memory card)
Can it be something else ?
yorgosb said:
Ι am no expert but I am sure I replaced HSPL with SPL 2.08
Click to expand...
Click to collapse
so, is that spl 2.08 or hspl 2.08 or spl 2.08.0000 or hspl 2.08.hspl? clarity please, leaving off the last 4 digits prevents us from double checking your work.
enter bootloader, whats it say next to spl? (all of it, not just the x.xx bit)
samsamuel said:
so, is that spl 2.08 or hspl 2.08 or spl 2.08.0000 or hspl 2.08.hspl?
Click to expand...
Click to collapse
Entering the bootloader right now says 2.10.0000
It must have been changed after flashing the official 2.13.531.1 (via USB)
Prior to doing that I had run the utility hspl3 and chosen 2.08.0000 (there are 2 choices in this utility as you say 2.08.0000 and 2.08.hspl) so (I thought) I had replaced the hspl with the official loader
Does this utility (hspl3) effectively changes the SPL or just updates the displayed number ?
Do you suggest following the micro SD card method to flash and not the USB method ?
I read somewhere that the ONLY way to replace the SPL is by flashing from micro SD...so what is the hspl3 utility for ?
Can you help me with that please ?
I need help because the phone right now although it seems to have been flashed correctly to official 2.13.531.1 and displays 2.10.0000 as it's SPL version freezes and restarts every some minutes...
yorgosb said:
Entering the bootloader right now says 2.10.0000
Click to expand...
Click to collapse
thats stock - any ending 0000 is stock
It must have been changed after flashing the official 2.13.531.1 (via USB)
Click to expand...
Click to collapse
yes, because you chose teh wrong 2.08 (next step) it will be changed by usb flashing. Had you chosen 2.08.hspl, this would still say 2.08.hspl
Prior to doing that I had run the utility hspl3 and chosen 2.08.0000 (there are 2 choices in this utility as you say 2.08.0000 and 2.08.hspl) so (I thought) I had replaced the hspl with the official loader
Click to expand...
Click to collapse
you replaced stock with stock
Does this utility (hspl3) effectively changes the SPL or just updates the displayed number ?
Click to expand...
Click to collapse
completely changes the actual spl software in your phone.
Do you suggest following the micro SD card method to flash and not the USB method ?
Click to expand...
Click to collapse
usb, always usb
I read somewhere that the ONLY way to replace the SPL is by flashing from micro SD...so what is the hspl3 utility for ?
Click to expand...
Click to collapse
thats old instructions.
for a start hspl .exeis for applying hspl, not just removing it - you can simply run hspl3 (or hspl4, whichever, makes no difference) - choose an spl ending .0000, hspl is gone. choose one with .hspl and, , , guess, , , yes! it loads hspl onto teh phone.
Can you help me with that please ?
I need help because the phone right now although it seems to have been flashed correctly to official 2.13.531.1 and displays 2.10.0000 as it's SPL version freezes and restarts every some minutes...
Click to expand...
Click to collapse
yep, happens a lot that, especially with stock roms,, give 3.14 a try perhaps.
3.14.531.1 has more problems...not only it freezes with certain applications (or making phone calls) but it freezes when inserting the microSD card as well...that's why I went to 2.13.531.1...at least I could keep the microSD inside without freezing...
And that's why I think it's not a firmware-software issue...that's what I'm trying to verify...
Now I have another bigger issue...after trying to flash a firmware that I think it wasn't T-Mobile's by mistake (the phone is T-Mobile model) the SPL is now 3.03.0000 and the 2.13.531.1 and 3.14.531.1 firmwares refuse to start flashing
Is there something I can do ?
I want to go back to 2.13.531.1 so I can sent it to T-Mobile
Thanks
Use hspl4, choose 2.08.hspl, reflash 2.13.
Sounds like you flashed a non tmous stock 3.14,,, don't do anything that silly again.
Just confirm for us,,, your send key is green, right?
Thank you very much I used hspl4 and managed to go back to the proper ROM
As for the send key if you mean the key with the little telephone on it yes it's green...the phone is T-mobile it says so on the top
Now that I have tried 2.10.531.1 - 2.13.531.1 and 3.14.531.1 versions and all 3
suffer from strange freezes and restarts when making phone calls or watching movies from the internet or the storage card (after some time) don't you think it's safe to presume that there is a hardware fault and return it to the vendor ?
Do you think there is something else for me to try ?
Thank you again for your help...

Please help me revive me 1 year dead phone!

Hi folks! Please help me! I killed tons of nerves because of this phone!
So here is my sad story. 1 Year ago i bought second hand HTC HD2. Seller told me that phone is locked to T-mobile(Not US one!! UK one!! Transaction was held in UK). After I got phone I rushed home to install Android and I was successful at this point. Then I bought a unlock code from ebay, so I Finally could make phone calls. Then I realized that the only way I can insert code is putting back WM 6.5. And here the worst part starts. I read hundreds of manuals but still was unsuccessful. I downloaded many official WM 6.5 ROM installers but they didn't flash my phone. They just got stuck at 0% and error pops up. I was trying it for a week and then I just raged and put phone to the shelf and was waiting til I get will power to start over again.
I hear that every phone needs its own ROM installer for particular region and operator but I couldn't find UK T-mobile ROM so used many others and it didn't help.
I also heard that by IMEI it is possible to find to what operator the phone is locked(just to check if seller didn't lie me) but again I didn't manage to do so.
Here is my IMEI 354120035834066
Please experts help me, little nooby, with this horrible situation.
thank you
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
samsamuel said:
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
Click to expand...
Click to collapse
Thank you, but always when I am trying yo install HSPL4 critical error comes up. I think it comes up because I have spl 2.1000000 which should be 2.08 I found information that in order to downgrade to 2.08 I need to flash official ROM. But when I am trying to do so it is always stuck on 0%...
I am so $%^& up ...
any ideas?.... thx
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Mister B said:
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Click to expand...
Click to collapse
Hi. Thanks for ROM, but still.. got stuck on 0% and doesn't go further..
When I try to install HSPL4 it always gives me critical error...
Fixed my problem. Now everything works fine!! Thank you very much guys!!
how ??
rom4eg said:
Fixed my problem. Now everything works fine!! Thank you very much guys!!
Click to expand...
Click to collapse
explain

Bricked my HD2?

Hello all
My dad own a HD2, the flat cable has been replaced. When you turn it on, you just see a white screen sometimes you see HTC logo, and the down left side you see
R 2.05.51.05_2
G 15.28.50.070
B 1.48.71294
We went into 3 colour mode, but we can't make any factory reset.
I tried to flash HSPL but everytime i get an error (image attached)
Stock one is SPL-1.42.0000 XE
I run windows 7 x64bit
can someone please help me?
Update: I have downloaded RUU stock rom from xda, and after 1% its says ERROR 270 update error the image file is corrupted. check your update utility
efi2222 said:
Hello all
My dad own a HD2, the flat cable has been replaced and we tried to make factory reset but without any luck
as far as i know there is no way to flash stock rom through the recovery mode (3 colour mode) with original SPL
It's SPL-1.42.0000 XE
I tried to flash hard spl and it fails everytime i get an error CRITIAL ERROR (image attached)
I run windows 7 x64bit
can someone please help me?
Update: I have downloaded RUU stock rom from xda, and after 1% its says ERROR 270 update error the image file is corrupted. check your update utility
Click to expand...
Click to collapse
Try task 29 wipe phone re download the original ruu and retry . are you using a t mobile us based hd2 ? if so you need specific rom or you will brick device !
also read these 1st to make sure you are doing it right, you should not need to return to stock to flash.
[TUT] Flashing your First GSM USA 1024LEO ONLY!! (For Noobs) http://forum.xda-developers.com/showthread.php?t=653614
[GUIDE] Flashing Your First HD2 NAND Android Rom [For Newbs] http://forum.xda-developers.com/showthread.php?t=893948
[GUIDE] Flashing Your First HD2 Clockwork Mod Android Rom [For Newbs] http://forum.xda-developers.com/showthread.php?t=1044830
task 29?
i can't make a factory reset. I have tried original ruu i get the same error
i tried to find it though htc but i don't see the download section there....
I know i must flash the same model, it's not a t-mobile phone, it's the regular one (99HJY035-00)
http://uk.hardware.info/productinfo/89425/htc-touch-hd2-uk
What can i do?
Follow the link on flashing android and see if it works . If it does then stick with that !
Sent via old skool carrier pigeon
---------- Post added at 01:52 AM ---------- Previous post was at 01:50 AM ----------
Ruu error might be miss match with imei original firmware. Go for Android !
Sent via old skool carrier pigeon
I prefer WM.
I know, but i can't find th place to enter my imei to download original RUU from htc site. Why HSPL doesn't work?
efi2222 said:
I prefer WM.
I know, but i can't find th place to enter my imei to download original RUU from htc site. Why HSPL doesn't work?
Click to expand...
Click to collapse
Its been a long time but im wondering if your problem is goldcard related, you really need somebody who has more expereince recently with wm as my memory is not so good on this now im afraid, hold on what exactly word for word is the error when installing hspl? does it say anything about missing files? are you flashing in bootloader mode (3 colours) and are you running the flasher as administrator???? right click run as administrator??
Originally Posted by powerofthink
1. Use Task29 tool on HD2 toolkit. (it erase all of your rom)
2. HD2 Toolkit 4.2.0.1;Use this tool. it has own HSPL (and also Task29, Magldr, Recovery) tool. choose 2.08.HSPL.
http://www.mediafire.com/?2qz0xa7xfxney47
(after this, if you want to load 3.03.HSPL, then use your HSPL4 tool)
3. after that install this radio rom;Radio ROM 2.15.50.14;
http://www.mediafire.com/?1th8o158r2t6dba
4. And after that you can install original win 6.5 RUU rom or any custom win 6.5 rom. [/QUOTE]
HSPL3 says;
Quote:
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
Hope this helps source:http://forum.xda-developers.com/showthread.php?t=611433&page=355
I tried to download your tool. clicked HSPL then tried to flash 2.08 HSPL
i get the same error like in the first picture
CRITICAL ERROR
flow: 00000006
Error code: 00000014
Description: Unkown
yeah i run it from the bootloader mode, and i do run it from administrator
efi2222 said:
I tried to download your tool. clicked HSPL then tried to flash 2.08 HSPL
i get the same error like in the first picture
CRITICAL ERROR
flow: 00000006
Error code: 00000014
Description: Unkown
yeah i run it from the bootloader mode, and i do run it from administrator
Click to expand...
Click to collapse
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
---------- Post added at 11:34 PM ---------- Previous post was at 11:30 PM ----------
swukjay said:
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
Click to expand...
Click to collapse
Also you can factory reset by holding both the up and down volume buttons down at the same time and switching the device on with the buttons still held down !
swukjay said:
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
---------- Post added at 11:34 PM ---------- Previous post was at 11:30 PM ----------
Also you can factory reset by holding both the up and down volume buttons down at the same time and switching the device on with the buttons still held down !
Click to expand...
Click to collapse
I tried also your tool same error
as i wrote at the first message i can't make factory reset god knows why.
efi2222 said:
as i wrote at the first message i can't make factory reset god knows why.
Click to expand...
Click to collapse
because theres no rom on the phone to perform a hard reset on.
samsamuel said:
because theres no rom on the phone to perform a hard reset on.
Click to expand...
Click to collapse
Well I hope you can solve this one as I have to admit defeat, I know is the error code can indicate a damaged file but he has re-tried with a new flasher and its the same error, I was wondering if it was a goldcard issue as I seem to remember that can cause a flash fail, but we don't use goldcards anymore, I suppose it is possible its bricked but if its entering the tri coloured screen it should flash, so I am stumped, your turn lol
How the rom got deleted? we just replaced flat cable
Anyway, there is a way that i can do flash the rom?
i was assuming you'd done a task29, (i dont read back previous posts, it'd take me forever, heh, so sometimes i miss / miss-remember something)
Just had a quick 20mins reading and googling, , strange thing is, , your line "B 1.48.71294" , , , thats an odd looking rom version, it would normally be something like 1.43.206.4, , where the .206. gives the rom locale, and carrier (206 is O2 uk, for example)
71294 is (i think) a build number, something like that, but i dont remember it ever being displayed on the start screen (course its been a loong time since i booted winmo)
If i remember correctly, it gets that info from the registry of the installed rom, which would suggest to me the possibility of a non stock rom, something thats been messed with, you sometimes see people post odd entries after JTAGGing and the like.
What's the history of the phone? you know where it originally came from? the original carrier? has it been repaired in any shady one-man phone repair shops?
for me, id try the following,,, get a 2gb (4gb at a push, certainly no bigger) and make a goldcard (instructions here - gc creator here )
get the wwe unbranded 3.14 rom, extract the ruu_signed, rename to leoimg,,, (blah blah u know how to sd card flash)
samsamuel said:
i was assuming you'd done a task29, (i dont read back previous posts, it'd take me forever, heh, so sometimes i miss / miss-remember something)
Just had a quick 20mins reading and googling, , strange thing is, , your line "B 1.48.71294" , , , thats an odd looking rom version, it would normally be something like 1.43.206.4, , where the .206. gives the rom locale, and carrier (206 is O2 uk, for example)
71294 is (i think) a build number, something like that, but i dont remember it ever being displayed on the start screen (course its been a loong time since i booted winmo)
If i remember correctly, it gets that info from the registry of the installed rom, which would suggest to me the possibility of a non stock rom, something thats been messed with, you sometimes see people post odd entries after JTAGGing and the like.
What's the history of the phone? you know where it originally came from? the original carrier? has it been repaired in any shady one-man phone repair shops?
for me, id try the following,,, get a 2gb (4gb at a push, certainly no bigger) and make a goldcard (instructions here - gc creator here )
get the wwe unbranded 3.14 rom, extract the ruu_signed, rename to leoimg,,, (blah blah u know how to sd card flash)
Click to expand...
Click to collapse
Great info, I did suggest to the OP that he may need a goldcard but its been a long time since I have made one, hopefully he will get his phone working soon !
How task29? i don't have HSPL and you must have it do task29
My dad officaly bought it from the offical import of the phone in israel, "Newpan", with offical hebrew on it
Simfree from factory.
It was repaired by him
Clicked "'Get SD Serial and Disk ID" - the software get stucked. it's suppose to take that long?
efi2222 said:
My dad officaly bought it from the offical import of the phone in israel, "Newpan", with offical hebrew on it
Simfree from factory.
Click to expand...
Click to collapse
hmm, cant find any reference to an official (as in htc) newpan rom, just a few mentions of people installing something from the htc desire to get rtl text working, perhaps newpan cooked their own, , shouldnt matter though, at least we're sure its not a jtagged device, or a rebuild from parts.
It was repaired by him
Clicked "'Get SD Serial and Disk ID" - the software get stucked. it's suppose to take that long?
Click to expand...
Click to collapse
no, it shouldn't, what sd card reader are you using? a usb one? one in teh front of a pc? cos if they're usb mounted then you actually often get the cid of the card reader not the card, ,
In htc site you can't find roms for hd2 at all
Through my samsung i9000 because 64bit doesn't support my card reader
even though it's not connected it's stuck.
sorry, out of ideas, other than hunt out sources of card readers, , friends computers, laptops, other phones, multibooting a 32bit operating system.,,,,
samsamuel said:
sorry, out of ideas, other than hunt out sources of card readers, , friends computers, laptops, other phones, multibooting a 32bit operating system.,,,,
Click to expand...
Click to collapse
I will connect it through SD adaptor straight into a laptop
efi2222 said:
I will connect it through SD adaptor straight into a laptop
Click to expand...
Click to collapse
Same error on trying to flash hspl (other computer running win7 32bit) and also trying to make a goldcard. Revskill just get stucked

[POSSIBLE FIX][AT&T] Successful Flash Back to 1.10 Bootloader

Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
I had to flash SPL via Y-cable per Cotulla's instructions in the HSPL Thread. But you may not need to let it sit overnight, I don't know. Maybe you can flash right away and get back to 1.10 or maybe not. It was just an unplanned event that had a brilliant result.
I hope it works for you too.
nikola92 said:
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
Click to expand...
Click to collapse
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
nikola92 said:
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
Click to expand...
Click to collapse
Please check out my post under debrand instructions under Windows Phone 7 development; you do not need your SPL to read 1.09 or 1.10 to successfully HSPL; it is imperative with whichever ROM you use for your device to read "HTC Titan x310e" not "HTC Titan P139100" following that first flash via Gold Card or everything that follows is mute. It is the 2nd step that will test your patience if you find yourself staring at "Entering USB Host Mode..." If following your flash of SPL205's NBH file you do not read on that screen, "Radio - OK", "Bootloader - OK", "Update Successful, UPDATE COMPLETED" your device will not HSPL on the next step. I recommend from the very beginning you rename the .NBH files to ETERDIAG (8 characters; no more) for steps 1 and 2 flashing via Gold Card. When you make your Gold Card use Quick Format; do not re-format your card following step 1; it is not necessary. I do recommend prior to copying the respective .NBH files to your Gold Card that they are renamed prior to copy. One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
berrywr said:
One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
Click to expand...
Click to collapse
This exactly. I was able to make calls and use the device as intended. Not like I wanted, but definitely as intended.
I was wanting to get back to stock SPL because I thought it was the only way to flash. The Titan forums are full of people that have been unable to attain HSPL due to the idea of being stuck on 2.5 bootloader was the cause. If your method works, that's awesome. As I said in my post, maybe it was a fluke but it seems so much easier to flash from stock. My primary device now is a One X so I may do some tinkering with my Titan soon. Regardless of how it turns out I appreciate your input into this.
R
But the now i when i write ETERDIAG i get flasing progres to start it comes nearly to end and then i get error 39 update terminated
Please Mr. berrywr Can help me ?
Pardon my English i'm an Italian Titan owner
I try your Plan B to debrand and have HSPL on my device because it doesn't go on using ETERIMG
I go on with ETERDIAG and everythings go in right way but ..
when i try to flash the renamed ETERDIAG.nbh copied from “SPL205” folder
my device don't FREEZE to Entering USB Host Mode but return on bootloader screen
i try after 15 or 20 minutes to move pointer with volume button and i'ts died no moove nothing change
only when i disconnect usb cable it's possible to move pointer up the bootloader menù
Now i try to change rom .
i start with european rom IMG_Eternity_HTC_Europe_1.09.401.02_Radio_16.23.02.09_A_16.24.00.23_Signed_ETERNITY_RELEASE
and i want follow your help and try with IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE.nbh.
hope to read HSPL on my device please if someone have same problem PLEASE help me go on with my job
i write back if everythings go ok wih cingular rom but .. ok i write back
Best Regards Fabio Ducilli form Italy
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
silentP said:
Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
Click to expand...
Click to collapse
It did not work for my titan...
ppgame said:
It did not work for my titan...
Click to expand...
Click to collapse
Sorry to hear that my friend. However, berrywr has been giving some excellent tuts for flashing. Thanks for giving it a shot though.
Specification of proble titan 1 hspl
berrywr said:
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
Click to expand...
Click to collapse
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
wileharley said:
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
Click to expand...
Click to collapse
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
nikola92 said:
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
Click to expand...
Click to collapse
I restarted my device in Bootloader Mode; it reads as follows:
1st line: PI39100 - That's Papa India Three Nine One Zero Zero
2nd line: HSPL2.5.160015.3(137079)
3rd line: eMMC SND 15188MB
4th line: CotullaH(F:81, ID:1, V11,B:F8)
5th line: "Double Space"
6th line: Radio-17.5006.08.27 (This is the required radio for the Eburon WP7.8.8858 custom ROM).
In regards to your device reading x310e; that's good news! You're half way there. You need to have a successful second flash with your gold card with SPL205. Your device will automatically restart and return to Entering USB Host Mode prompt...it is this step you must have patience; it has to read Radio - OK, Bootloader - OK...Update Successful, UPDATE COMPLETED; it cannot be anything else or any combination other than these four.
Upon completion of the 2nd flash...SPL205's nbh file does your display indicate both Radio-OK and Bootloader-OK, Update Successful, UPDATE COMPLETED?
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
nikola92 said:
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
Click to expand...
Click to collapse
If what you've written is correct then you are two-thirds the way there and what's left to do is connecting your device to your computer with Zune running, Your device is to be in bootloader mode when you do this, look for USB at the bottom and execute the program by right clicking the application and run it as administrator.
I did that, proces said finished and boom no hspl cotula writing......
Same problem with HSPL for me
[/COLOR]
berrywr said:
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
Click to expand...
Click to collapse
i do the same :
ok flash the european rom using ETERDIAG .. ALL OK
ok flash spl 2.05 and everything ok Radio etc with ETERDIAG MODE ALL OK
ok install as adminitrator DFT__HSPL_WP7SG1 and ALL OK
but when i restart it can't find cotulla inside my bootloader
i'm happy because my original rom was only english and now i have european rom but
i need unlock it with HSPL .. grrr
---------- Post added at 06:38 PM ---------- Previous post was at 06:00 PM ----------
06.57 PM 01/01/2013 just finish to RETRY all .... nothing good only my italian rom
not work for me too
No good news
No work for me too

Categories

Resources