I found a couple posts about this but people seemed to just return or RMA it. Thought maybe my experience might help others and was curious if anyone else has this problem.
A few times I have picked up the Prime and hit the power button and the display would not come on. If I plugged it in I would see the green light on the power button come on and go off when unplugged. It appeared to still be attached to the WIFI. If I held the button down it would buzz, but nothing else.
I found out that if I held the button down, waited for it to buzz then continued to hold it down for another 30 secs or so (seems like it takes forever) the Prime would then reboot and I would get the Eee Pad boot screen.
I have been storing my Prime in the box to keep it clear of kids and cats until I get a case. My wife ended up picking up this cheap case from Walmart which used rubber bands around the corners, and this triggered the problem by holding down the volume up button. I have not been able to reliably reproduce it, but it seems like holding down the volume button (or combo of power and volume button) puts the device in some diagnostic mode or something that shuts off the screen.
The natural tendency to release the power button immediately after the buzz while trying to reset made the device seem like it was broken. Luckily I figured out how to start it back up so I did not return it or RMA; however I wonder how many others experienced this problem.
This appears to be a software problem and not a hardware issue. I have not had this happen since I started being cautious about the volume buttons, but have not tried to reproduce on the last firmware update.
I have had no other issues with the Prime. It runs great, WIFI works for me and I could care less about the GPS issue. However, this display thing has scared me a handful of times until I figure out how to reset it.
Anyone else have this kind of issue? I was going to wait for ICS and then see if I could reproduce it before calling ASUS, but it has not been crippling especially once I figured out that when all else failed just hold down the power button until the screen came back on.
I've had this problem as well, three or four times so far. Actually, it happened to me on the first full day I had mine, and was really freaking me out. I've been using the pinhole reboot button to get it working, but it sounds like you were more patient with the power button than I was.
I can't replicate it either, exactly, but I've noticed that it's only happened after extended periods (6+ hours) of inactivity without charging. I also looked at my battery usage last night, and saw that my device constantly is awake; maybe somethint's happening when it tries to sleep?
Anyway, I feel the same way you do - I'm waiting for it to happen on 4.0(.3?) before I really worry.
I've had this happen twice. held down the power button to reboot. I can't reproduce it either, but I don't have any problem with the device sleeping. I'm at 50 hours of uptime now (15 on current charge) and have not run into it. Mildly glad to see its not just me though.
TF201 | XDA Premium
Only once tonight. Scared me until I saw the boot screen. Interesting since it has been rock solid until this. No other problems just didn't turn on. Glad to be back working.
Sent from my Transformer Prime TF201 using Tapatalk
never had that issue...have used it quite a lot in many different situations
This morning it didn't wake up. I got it to turn on by holding get down the power and volume down button. Hopefully it doesn't happen again.
Sent from my Transformer Prime TF201 using Tapatalk
happened to me tonight freaked me out for a while - had to use the reset pin hole
I've had the same exact problem andthe funny thing is I also have a case from Walmart with the rubber bands. Is yours the case logic? Since reading this post, I've removed the upper left band. I wish my case would ship already!
guys if you're familiar with transformer 1 and hacking\custom ROM tegra devices power + vol up = apx mode kind of download mode blank screen, nothing wrong with the device just working like it should. now just a blank screen with sound when u plug in could be defective screen has happened to me
Awesome to know this is expected behavior.
I didn't have the original transformer, and googling has just led me to people who can/can't get into the mode, so I'll ask here: what exactly is apx mode? I get what it's for, sort of, but what is it?
also happened to me while it was in a case. maybe the power button was pressed too long or something...
this happened to me yesterday, except the screen is still off....tried everything mentioned and it wouldnt turn back on, its fully charged...i get no buuz sound or anything...
LOL, I was just searching for a thread like this.
Mine has been working flawless for the last 4 days. This morning, would not turn on. I tried every combo and button push I could think of.
No LED charging lights, nada.
I finally reverted to the paper clip in the reset hole. Booted right up.
Don't know what the issue is.
reset button wont even work for me...
Yes It happend to me yesterday twice... i think if we leave it for an extended period without out charge , the screen is getting locked somehow... both the times i have held the power button till the buzz.. then it rebooted....
Same behavior here, was fully charged in the Morning, and plugged in, when i got home Both LED's (Dock and Tab) were green but the Screen won't turn on, pressing the Power button for 10sec rebooted the device, maybe some kind of power saving feature... hopefully it will be fixed with ICS
Okay, rockstatus90's problem seems different, but the rest of us, pceasar explained that we're likely entering APX mode, right? It's designed behavior? Now I just want to know what APX mode is, and if there's an easier way to exit than rebooting.
Happened twice for me so far.
chinly43 said:
Okay, rockstatus90's problem seems different, but the rest of us, pceasar explained that we're likely entering APX mode, right? It's designed behavior? Now I just want to know what APX mode is, and if there's an easier way to exit than rebooting.
Click to expand...
Click to collapse
Yes this is normal. Although most other Android devices seemed to give some sort of on screen message.
It is mentioned here as a process of rooting the original TF:
http://eeepadhacks.net/transformer-hacks/how-to-root-your-eeepad-transformer/
Basically, this is a mode that outputs to your PC and is supposed to blank your screen. You are supposed to reboot afterwards, so there is no other way out.
I have not had the problem since being sensitive about pushing volume+ and power at the same time.
rockstatus90 said:
reset button wont even work for me...
Click to expand...
Click to collapse
Unfortunately it looks like return or rma is your solution. I would try to call Asus and see if they can troubleshoot it. Best case they can reset it for; worse case its dead.
Really wish you could pull the battery. Thats the sure fire reboot.
Related
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
EDIT: Just happened again, although now I can't seem to get the thing back on. The screen is just off and vol. up + power only makes the thing vibrate after a few seconds. I simply left the prime on the lock screen and came back and it was stuck again.
Prime BT tether lockups
XHolyPuffX said:
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
Click to expand...
Click to collapse
Mine does the exact same thing when I tether it to my Sensation with BT.
I'm still on 2.11.1 though
UPDATE
I just manually updated my pad to .13 this morning. It did NOT alleviate my problem but it didn't make it any worse. Unlike many other user who report the lockups when sleep now, mine still only occurs when I tether BT and it goes to sleep. On the upside, I've tested my wifi and do confirm an improvement ~20% increase in signal strength and quality.
According to dd-wrt on my router signal increased from about ~49% to 63%
and Wifi analyzer signal strength ~77-68dB to ~54-47dB. I have not tested GPS.
Apparently the build variance between pads are reflected by the variance in the effects of the update
nattylite said:
Mine does the exact same thing when I tether it to my Sensation with BT.
I'm still on 2.11.1 though
Click to expand...
Click to collapse
How do you get it back on? I can't seem to power it up now.
EDIT: Nevermind, I just held power and it turned back on after about 5-7 seconds. I think it might be a "Wifi off during sleep" issue..but idk.
XHolyPuffX said:
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
EDIT: Just happened again, although now I can't seem to get the thing back on. The screen is just off and vol. up + power only makes the thing vibrate after a few seconds. I simply left the prime on the lock screen and came back and it was stuck again.
Click to expand...
Click to collapse
same thing is happening to me after the update. My prime never used to do that but something in the update screwed with it. is there anyway we can revert back?
Doubt this is an update issue as I haven't seen it yet or most others. Or they all would be posting about it. That is strange though. You all didn't root n go messing around with stuff did you? Lol. If anything I'd try a fresh reboot. Maybe even clear out all the caches. Something else is seeming to cause this. By any chance did you install chrome beta? Some users reporting strange things since installing it. I don't think its the app but it is strange though or coincidence.
demandarin said:
Doubt this is an update issue as I haven't seen it yet or most others. Or they all would be posting about it. That is strange though. You all didn't root n go messing around with stuff did you? Lol. If anything I'd try a fresh reboot. Maybe even clear out all the caches. Something else is seeming to cause this. By any chance did you install chrome beta? Some users reporting strange things since installing it. I don't think its the app but it is strange though or coincidence.
Click to expand...
Click to collapse
no I didn't root. I may factory reset if it keeps doing it and see if that works. I got a decent working prime and it would suck if this update is giving me problems. yes I did install chrome beta but this issue happened before I even installed it so that can't be it.
Ok, this has to do something with the update.
My perfectly fine from before prime wouldn't unlock. I couldn't get it to respond. (I thought it was dead..) I tried to unlock and pressed volume, did nothing.
I just read this thread and tried holding the power button and it vibrated and booted after the hold...
Asus needs to stop the patch roll out untill this is fixed...
Same problem for me. And after a short sleep, it wakes up, but there is a delay of about one half second that didn't used to be there.
-gary
After that one sleep, it has not yet repeated since last night for me
not only did mine do the same thing but it also killed my battery life while my Prime was sleeping... epic fail asus its time to return for a refund and never look back.
Maybe try reverting back and see if the problem goes away.
This hard-to-wake-up issue happened to me once after the update, but my Prime did finally wake up. Have not had the issue since. There was a lag in the wake up yesterday also, as others have mentioned, but even that seems to be gone now (or I'm just used to it).
Possible fixes for this situation:
1) Hard reset (stick an open small paper clip into the little hole just below the microSD) -- I'm sure most of you have tried this already...
And, if that doesn't work:
2) Hard reset, then reapply the .13 firmware update manually right after (assuming that is possible)
My tendency is to always do a hard reset just before any firmware updates -- makes me feel a little more confident. I was lazy and did not do that yesterday, but it won't happen again.
enough with this crap
Dude, you really gotta stop trolling, this is the third thread you are spewing this crap in in the last three I read.. You obviously are not returning it, you just like to *****.
PrimeTimeBro said:
not only did mine do the same thing but it also killed my battery life while my Prime was sleeping... epic fail asus its time to return for a refund and never look back.
Click to expand...
Click to collapse
unsure if this is the right thread, but mine's been acting up since the update as well. when i'm actively using it and turn off the screen, it boots up as quick as before to the unlock screen. however, after letting it sit for a few hours, it seems to have shut off where i'll have to hold the power button on for a few seconds (after 2 or 3 tries) to get it to boot up again as if i reset the tab.
Having the same issues with mine as well. I have installed Chrome Beta, but had it running for a few days pre-update without issue.
I almost always keep mine in the dock, but haven't had a chance to determine if it only happens in the dock or not.
i have seen this occur in the past ..before the update.. i thought the battery was dead but plugging in the charger didnt do much.. held the power+vol up 3 times finally woke up .. and said 36% battery left... i m on the verge of returning this after 2 weeks of use.. just cant get over these silly silly issues
Mine just did the same thing. I'm on the newest update. Had to hold power button 10+ seconds for it to come back.
Sent from my Transformer Prime TF201 using Tapatalk
Mine died over night with a charge of 36% in balanced mode. Had to hold the button down for 10 seconds to get it to turn on today after it was plugged in the charger for 20 minutes. Now when i wake it out of sleep there is a .5/1.5 second delay for the screen to come on.
Same issue
Had absolutely no issues with my tablet prior to this update - no random reboots, but now if it's off for a minute or more, I have to hold power in for 7-12 seconds to boot up the system.
Hey, just a thought.
Maybe also include the first few of your tablet's serial number to see if the problem is consistent with some batch(es) and not others? May help others that's going to update...
I hope this is the right sub-forum to open this thread if not please movie it.
Half an hour ago I Got the 9.4.2.15 firmware update from asus. after the update was applied my prime asked me if I want to turn it off....I approved and the device shut down and stayed off.I tried to turn it on and nothing happened.
When I applied the update I had more then 80% of the battery.
I plugged the phone to the charger and the charger light on the power button changed from orange to green
While the Prime was charging(and after it was fully charged) I tried to do some stuf
I tried to press the on button and nothing happened and no vibration.
I tried to hold the on button for about 30 seconds and the only thing that happened is that I got a vibration(the same you get when you turn on your device).
I tried to reset the device with the reset hole near the microsd with a needle and nothing happened.
I tried holding the power button and the volume button(once the up and the other time the down) and nothing happened except the vibration after about 10 seconds.
ANY IDEAS?
*my biggest problem is I purchased the Prime from "Amazon US" and I don't leave in the us...How If I need do I use my ASUS warranty.who do I connect?
Thanks.
Try draining the battery completely then charging it back up. Then try to boot it up again. You might have a glitch or bug. Its always good after an update is applied to let it update then it reboots itself. After it loads back up,go into home screen. Then **** down device and cut back on. This will eliminate anything happening from rogue codes.
http://service.asus.com/InfoPage.aspx?rid=7
Good luck
demandarin said:
Try draining the battery completely then charging it back up. Then try to boot it up again. You might have a glitch or bug. Its always good after an update is applied to let it update then it reboots itself. After it loads back up,go into home screen. Then **** down device and cut back on. This will eliminate anything happening from rogue codes.
Click to expand...
Click to collapse
Any Idea how do I drain the battery, The Prime has now 100% battery and I am unable to turn it on...the screen stays black?
jdbaker82 said:
http://service.asus.com/InfoPage.aspx?rid=7
Good luck
Click to expand...
Click to collapse
Thanks.
Any more ideas?
*By the way I have the option to take the prime to a shop that could fix it, I am sure the problem is a software bug and not hardware...Should I try doing this because ship it to asus ans back will take about 3-4 weeks.
Try a hard reset and if that doesnt work do a search for this (EP201_SDUPDATE.ZIP)
ohwell said:
Try a hard reset and if that doesnt work do a search for this (EP201_SDUPDATE.ZIP)
Click to expand...
Click to collapse
I am unable to do "Hard reset" because the device do doesn't start, after pressing the power button nothing happens the screen stays black. the onle response I get from the device is vibration(after I hold the power button for about 10-12 seconds).
I don't think that "EP201_SDUPDATE.ZI" will help because I don't have accesses to my bootloader
Did you happen to drop the device or bang it pretty hard? If so, could be a chance the connector to your display is loose and device is actually on but the screen is off. Best way to check this is to connect your prime to your t.v. thru HDMI. Then try to cut it on. If something displays on your t.v. but screen still won't cut on, then connector came loose from your display. That is the best way to check. Plus you could also operate tablet like that.
Nope,didn't drop or hit it.
Unfortunately I don't have HDMI cable that connects to the prime.
your idea is good but even without the cable I am sure it's not the problem...but lets say that it is the problem...then if the device is actually on I should be able the hear the sound it makes when I use the volume buttons and when I receive new emails...the thing is I am unable to produce any sound from the device.
I just applied my update and it didn't ask me if I wanted to power down, it did itself. Did you power down when it was starting to install?
My screen did say "power down" but I knew it would do it itself.
Maybe like doing a battery pull during a flash?
Sent from my Transformer Prime TF201 using xda premium
Maybe you are right and for some reason I turned the device off while it was in the middle of the update... so 5hat means as you said that I interupted the flash process...in this case the problem is the software of the device ...could I do somthing to fix it without going with it to a lab?
Sent from my Galaxy Nexus using Tapatalk
You might try inserting a pin or a paperclip into the reset hole next to the micro SD port.
PROBLEM SOLVED!!!
I decided to try and fix my prime one last time before I use the warranty. so I took a needle SMALLER one then I used the first time I tried to "Hard reset" the prime and inserted it into the hole near the microSD port....and this time I felt a "click"...I pressed for about 10 seconds and then released and the screen turned on
I immediately got the screen withe the open green robot and with a blue line under it that showed me that the update was applied....then the screen changed to the screen you get when you turn on the device(asus symbol and tegra3 symbol) and again I got a blue line showing me that the update is going on.
After the blue line went foreword to 100% it disappeared from the screen and I was left with the screen you get when you turn on the device(asus symbol and tegra3 symbol).
I have waited for about 20 minutes and nothing happened....I turned off the device with the power button and then turned it on again(this time the device responded after 1-2 seconds)...I got a vibration and the screen was on(asus symbol and tegra3 symbol). after a few seconds the screen changed to another screen( another ASUS symbol with a turning circle under it) after about 8 seconds my device was fully working all my data was present(didn't reset with the needle should have deleted everything?) and my software number was 9.4.2.15,so the update was fully applied.
I tried turning on and off the device for a few times and had no problems with it.
So basically the device is working and I have no idea what was the problem
The tip i got for everyone trying to reset the device with a needle/paper clip....YOU HAVE TO FEEL THE CLICK
that's awesome! Congrats!
These are expensive toys (in my case addiction).
Maybe it was a bad flash which can be really spooky if you're not rooted with a custom recovery.
Sent from my Transformer Prime TF201 using xda premium
My friend that I bought the Asus prime for, asked me if I could take a look at his prime.
Here is the screnario:
Listening to radio station app, screen went to sleep while the radio was still playing and he tried holding the power button down and nothing worked to reboot or wake up the prime. The Prime was left playing to drain down the battery. It has all its recent updates (.15), not rooted, and not unlocked. When I looked at it, I charged it up, I can see the light and turned green to full battery status. I can feel the prime vibrate as I hold the power button, I tried volume + power hold, tried the hard reset with the paper clip hearing the click next to the sd card slot holding it for 10-30 seconds. The laptop can see the folder in the prime as i hold the power button and also disconnects when i power down. ordered 12-28 from best buy so the return window has expired and its a BC0K serial number.
Anybody find a solution with a black screen prime that just vibrates and can be seen on the laptop before I send it for an RMA?
Was there any shock to the device? A small bump or anything, it sounds like the ribbon cable for the screen has become disconnected, there are some reports of this on the forums.
flyingwolf said:
Was there any shock to the device? A small bump or anything, it sounds like the ribbon cable for the screen has become disconnected, there are some reports of this on the forums.
Click to expand...
Click to collapse
This + have you went into recovery?
maybe try draining the battery again then charging up. ive seen a few post issue like this. if screen connection didn't break, then letting it drain again and charging up might fix it. good luck!
Actually, the prime was already drained maybe a total of 3 times. There was no shock to the device as it was working with the radio app on and when it was being listened to while it was on the bed, the screen went into sleep and could not wake up no matter what button was being pushed so the prime was left to drain its battery. My friend didnt know how to reboot, so he decided to left the battery to drain. Could the radio playing + sleep of death + battery drainage caused the permanent screen sleep? Too bad I dont have the micro hdmi connector to see if i can isolate the screen as the problem.
yup the micro hdmi would help a lot probably. But if your PC recognizes it I suggest you back up data that you need then try to do a blind factory reset so you can get rid of any non oem app installed including that radio app if any of them is whats causing the screen not to turn on.
1. Hold volume down then press and hold power.
2. When you feel it vibrate (this could take up to 10 seconds if the tablet was already on) wait another 5 seconds and then release both buttons.
3. After you release wait another 5 seconds (dont wait too long here or it will reboot on its own if you dont select anything after about 10 seconds) then press volume down 1 time and volume up 2 times.
4. The tablet will factory wipe and after another 10 seconds it will reboot.
If the tablet still wont turn on then you got another issue and that isnt caused by the radio app or any other app.
Didnt work. It just vibrated and the screened stayed black... Im wrapping this puppy up and bringing shipping it to the repair center. Thanks anyways.
Vibrates when power button is held but wont turn on
My Prime also has the basic problem. I use it daily for about 3 to 4 hours, reading replying to e-mails and web browsing. While I was reading, the volume started going up on its own and I noticed that even after I put in standby mode, the battery discharged so I shut it down completely.
After that I could not turn it on. When I hold down the power button it vibrates bit the screen does not come on even after I fully charged till the led turns green.
logical_motion said:
My Prime also has the basic problem. I use it daily for about 3 to 4 hours, reading replying to e-mails and web browsing. While I was reading, the volume started going up on its own and I noticed that even after I put in standby mode, the battery discharged so I shut it down completely.
After that I could not turn it on. When I hold down the power button it vibrates bit the screen does not come on even after I fully charged till the led turns green.
Click to expand...
Click to collapse
Had to RMA back to Asus for them to fix the display and it took about a week. Warranty covered it, but if you do RMA ask them to ship you a shipping label. You shouldnt have to pay for shipping it to them for a manufacturer defect. And take pics and videos of the tablet and packing for your safety. They just need the tablet and nothing else. Good luck
Asus is F-ing with my endorphines...
I've had my TF201 since March 30th. Been using it for 1 week and it suddenly went dead (nothing on the screen, no vibration if I held the power button down). Tried everything I could find on the forums, it didn't work so I sent it to repairs (not immediately, cuz I had more important stuff to do). They kept it for almost 3 weeks, got it back this last Monday (May 21st) and... it died out on me again yesterday night (after just 3 days of use, congratulations ASUS technicians!). I was simply browsing and I clicked on the icon to increase the luminosity to the maximum supported (IPS+, I was charging it at the time) and the screen suddently went black. Like "nothing visible on it" black.
After that, I tried numerous times to reset it (including the volume+power down, according to the indications in this thread) - all I could get from it was the vibration as if it starts. Nothing else popping up on the screen. I plugged it this morning into my computer and it got somehow recognized, cuz my W7 tried installing drivers for it (even tho it had recognized the tablet again after it came from repairs and I already had drivers for it installed) but failed with the error "APX - no driver found".
I've had enough. Two months already and only one week and half of actual use. It's pathetic, ASUS needs to be taught a lesson, so I'm calling Consumer Protection in my country and the European Consumer Protection Comission. All the forums that I've surfed are filled with reports of broken units and ASUS will just tell you "if you have a valid warranty we'll repair it for free". I DON'T ****ING NEED regular repairs every 2 weeks!!! I need a functional tablet that I can use or give me my money back!
I'll post the results of my tribulations here...
I had a user that suffered the blank screen.
When you think it's presumably on. Try a paperclip to the reset hole on the left side. His came back up at that point and hasn't done it again since.
Never had this happen on mine.
So I put my prime on my bed (it was on and working but closed in its dock) and proceeded to move my sheets to get in bed. The amount of static electricity it created was amazing (its been very cold and dry here) I didn't really think anything of it. I've shocked my prime touching it many times, however its completely dead. I have tried everything I could find in any post but it basically come down to this.
I let the unit charge fully and the green light comes on, but no matter what buttons I press and hold it never once vibrates (held power over 2 mins), nor does it show anything in device manager.
I was rooted and unlocked, I did the wheele nvflash thing more than a couple months ago. I have also hardware modified my device with external antenna for the WiFi when i got it less than a year ago.
i'm pretty sure i'm screwed but just looking for anything that might help.
mystkrh said:
So I put my prime on my bed (it was on and working but closed in its dock) and proceeded to move my sheets to get in bed. The amount of static electricity it created was amazing (its been very cold and dry here) I didn't really think anything of it. I've shocked my prime touching it many times, however its completely dead. I have tried everything I could find in any post but it basically come down to this.
I let the unit charge fully and the green light comes on, but no matter what buttons I press and hold it never once vibrates (held power over 2 mins), nor does it show anything in device manager.
I was rooted and unlocked, I did the wheele nvflash thing more than a couple months ago. I have also hardware modified my device with external antenna for the WiFi when i got it less than a year ago.
i'm pretty sure i'm screwed but just looking for anything that might help.
Click to expand...
Click to collapse
This may or may not help but I had it once where my prime would not turn back on.
I took it out of the dock and plugged the power cable directly into the tablet and then held the power button and it powered up with full charge in it.
Yours does sound like a short issue but it's worth a go.
flumpster said:
This may or may not help but I had it once where my prime would not turn back on.
I took it out of the dock and plugged the power cable directly into the tablet and then held the power button and it powered up with full charge in it.
Yours does sound like a short issue but it's worth a go.
Click to expand...
Click to collapse
Nope but thanx for the help
Has anyone ever seen one that wouldn't vibrate before?
Okay, so my prime was on the latest CM10.1 offered here: http://forum.xda-developers.com/showthread.php?t=2053269
I had TWRP 2.5.0.0 on it as well as the corresponding GApps. I did nvflash and everything on my Prime and it was working flawlessly since the day I bought it. I have had ZERO issues and thought it would never brick.
Just a few weeks ago, I began to notice my TF201 acting VERY slow. When I say slow, I mean like opening Solid Explorer, for example, would take a long time. I didn't pay it any mind and continued on watching movies on it, reading books, browsing and just my every day normal usage. Two nights ago, I copied over some files using AirDroid and saw that I had 36% battery left. I left it charging overnight and unplugged it when I woke up. When I came home, it wouldn't turn on. I don't know if my charger is borked and somehow f*ck'd up my TF201 while it was charging, but I can't think of anything else.
I've tried the following:
-plug it in and hold power button
-leave it plugged in to charge some more
-leave it unplugged for a few days to drain and then plug it in, holding power button
-pressing and holding the power button
-holding vol up + power (10+ seconds)
-holding vol down + power (10+ seconds)
-holding reset button (10+ seconds)
-plugging into my computer
The screen just stays off. No vibration or anything. If I look at the power button, it just stays orange, steady not blinking. If I leave it unplugged it goes off. If I leave it plugged, it stays orange never green.
Is my battery done? Fried? By the charger? I have babied this tablet since I bought it. I have a $60 Gumdrop case for it. It is flawless on the outside with zero blemishes. How could this happen? Has anyone else seen this kind of brick before?
Sounds like some sort of catastrophic hardware failure. Slowness and boot failure could be perhaps explained by fried eMMC/SSD but it's strange that it doesn't power on at all. Because of the speed issues you mention that were happening, it doesn't really sound like the battery.
I hope you get it figured out -- have you tried contacting Asus or any tablet repair specialists? Surely someone might be willing to talk some debugging. I take it that it's not under warranty anymore?
mnasledov said:
Sounds like some sort of catastrophic hardware failure. Slowness and boot failure could be perhaps explained by fried eMMC/SSD but it's strange that it doesn't power on at all. Because of the speed issues you mention that were happening, it doesn't really sound like the battery.
I hope you get it figured out -- have you tried contacting Asus or any tablet repair specialists? Surely someone might be willing to talk some debugging. I take it that it's not under warranty anymore?
Click to expand...
Click to collapse
It's definitely out of warranty --both the limited time and the fact it was hacked to the teeth. I'm not as upset anymore about losing that tablet. It barely had any XDA love anyway. Lol. My Xoom is at least still heavily supported by Team EOS and Steady Hawkin.
The reason why I suspect the battery is because of the fact it wouldn't turn on at all. The power button just stays orange. I could be wrong, of course.