Wifi Glitchy, but only on Android side of things - TouchPad General

I've been playing with an TP now for about a week or so. When I got it, the WiFi worked great, on both bootups. Now if I turn off the device and restart the WiFi never works on Android unless I go through the hassle of wiping my Delvik and or playing with a code I have for SuperUser. However if I boot up in WebOS, WiFi is there and connects immediately to any WiFi in the area.
Answers?!
Thanks in advance!

Not sure if Android wifi is perhaps detailed in another topic, but i'll post my issue here too while i keep searching for a solution.
I connect easily WebOS to Nexus One using "Portable Wi-Fi Hotspot" ..but in CM9 the wifi loops "Obtaining IP Address, Saving.. Obtaining IP Address" ..repeatedly.
Has anyone succeeded yet with Android-to-Android via portable hotspot?
EDIT: Okay, after re-applying sledgehammer, rebooting everytime i turn on TP's wi-fi (+ few FCs), disconnecting and reconnecting a few more times, it's finally connecting.. occasionally.

I'm not even trying to use the portable hotspot, at this point just trying to connect to my router at home, which it had no problem with earlier.
But the TP keeps looping the same as you...
"Obtaining IP Address, Saving.. Obtaining IP Address"
At least I'm not getting the 'force close' box anymore. Lol

I had terrible connection issues on CM7 and after installing CM9 all seemed fine until my first reboot, then I couldn't connect at all.
A few days ago, I changed my linksys router wireless channel from 11 to 4 and have not lost connection a single time since, even after multiple reboots. I have seen several others say they have had similar success.

However this happens no matter where I'm at, or who's router I'm using. ( I currently have an ActionTec, via Verizon), and I use the TP at school, so no idea what they have set up as wireless.

Had some issues with the portable hotspot from my iPhone but after making the TP forget the connection, toggling the wifi on both devices I can pick it up again. Not too bad. No issues with my home router.

I had to do the same, I 'Forgot' the network, then I toggled the Wifi on and then off. For whatever reason it has no issues staying connected to my home network now.
However at work I have to do that forget n' toggle everytime I reboot it.

Did you do a clean install or on top of CM7? When I loaded on top, I had many problems.
After an uninstall and fresh load of CM9, I do not have any problems like I use to experience in CM7. I would remove WiFi profiles and re-connect when going from Home to Office networks. I have none of that now in CM9, knock on wood.

I had issues frequently with CM7 and wifi, as was common. I haven't had any issues with CM9 or preludedrews latest build. I follow the "kill a fly with a sledgehammer" approach. I wipe data/factory reset, then wipe cache, advanced>wipe dalvik, mounts>format system, cache, data. Then installed. It takes an extra second to do all the wipes, but with experimental builds like this I always do it.
Now the only android issue I can't fix is ironically the xda app. In CM7, xron, CM9, or preludedrew's build whenever I try to do anything it FCs. That is my only complaint right now.
Sent from my Galaxy S II (i777)

I was not having the wifi troubles that two other touchpad owners I know were having. I installed Android on both of their devices, but couldn't figure out what to do to fix it and it was making me insane. Finally, we reset all our routers to a channel below 5 and found that they all connected to wifi well, HOWEVER, I found a better solution. I don't know if anyone has noticed this, but this must be a setting I fiddled with on my TP, that the other two TP owners had not fiddled with.
Go into Wifi Settings, then click the Menu button at the bottom left (the three bars)... click Advanced then click Regulatory Domain. In my touchpad, I had clicked on the 11 Channel option. On the two touchpads that could not regularly connect to wifi, neither had a selection made whatsoever under "Regulatory Domain." After clicking "11 Channels," all three touchpads can connect to wifi with no issues AT ALL, no matter the channel.
I almost can't believe this hasn't been posted in other forums yet, because it seems to be the key and much easier than setting every router you want to connect to, to a different channel.
Please let me know if this works.

Thanks for the tip. My touchpad had nothing selected either in that menu. Hopefully this will solve my wifi woes!

hotlikefriction said:
I was not having the wifi troubles that two other touchpad owners I know were having. I installed Android on both of their devices, but couldn't figure out what to do to fix it and it was making me insane. Finally, we reset all our routers to a channel below 5 and found that they all connected to wifi well, HOWEVER, I found a better solution. I don't know if anyone has noticed this, but this must be a setting I fiddled with on my TP, that the other two TP owners had not fiddled with.
Go into Wifi Settings, then click the Menu button at the bottom left (the three bars)... click Advanced then click Regulatory Domain. In my touchpad, I had clicked on the 11 Channel option. On the two touchpads that could not regularly connect to wifi, neither had a selection made whatsoever under "Regulatory Domain." After clicking "11 Channels," all three touchpads can connect to wifi with no issues AT ALL, no matter the channel.
I almost can't believe this hasn't been posted in other forums yet, because it seems to be the key and much easier than setting every router you want to connect to, to a different channel.
Please let me know if this works.
Click to expand...
Click to collapse
nice find thanks I'll give it a try

i cant even find the wifi settings/menu. i go into the wifi and can view the networks available, look at known connections, and when i look at preferences i'm only given one option to toggle which is whether the wifi turns on or off while sleeping.
so where do i look to find the above mentioned wifi settings which leads to the menu button that i cannot find? thanks.

Pvster said:
i cant even find the wifi settings/menu. i go into the wifi and can view the networks available, look at known connections, and when i look at preferences i'm only given one option to toggle which is whether the wifi turns on or off while sleeping.
so where do i look to find the above mentioned wifi settings which leads to the menu button that i cannot find? thanks.
Click to expand...
Click to collapse
I don't thank it is for CM9.

It's on top corner. You can access menus there. However, on CM9 build I do not have the regulatory options to change the channels as you explained. It's an advanced tab that gives me access to sleep policy, etc. Are you on CM7?

Yep, it's only CM7.

cdmcfud said:
I don't thank it is for CM9.
Click to expand...
Click to collapse
Sorry, I should have specified that I'm on CM7. It works so wonderfully for me that I won't be doing CM9 until many more of the bugs are worked out.

I'm running Miui with CM7 base. I do not see where these 'menu' options are. *head scratching*.. Is it under the 'advanced' tab?

Found it, but it to is selected with 11 channels already.

# rm -rf /data/misc/wifi && reboot
this also works, but it's a pain to have to copy and paste it and run it through the terminal daily. just hoping for a solid fix. cm9 seems to be the way to go, but once they have a few more of the bugs worked out.

Related

[Q] Problem with hone wireless network connection

A couple of days ago my wireless connection quit working at home. The wireless network icon turned white all the time, and never switched to green. I hard wire the modem/router (ATT Uversre 2Wire 3800HGV-B) into a 5 port switch and plug my computer, network storage drive, and media streaming box into the switch. I've had all of this set up for a few months in it's current configuration and there was never an issue before. This just seemingly happened out of the blue...funny how computers do that sometimes, right? I have an HTC Aria, I was running CM7 RC1 when the problem happened, I just updated to RC2 hoping maybe it would change and it didn't.
After reading posts and checking settings here's what I've found:
My wireless router is set to act as the DHCP server. I set all of the IP addresses manually. I've had it set this way for some time, haven't made any changes recently. The attached network storage (D-Link DNS 323 also has DHCP server capability, but that is disabled)
I found that while my phone was set in the router's setting to connect to 192.168.1.67 for whatever reason it was connecting to 192.168.0.200 (which is out of range, my DHCP is set to address to 192.168.1.64 - 192.168.1.253)
Any idea what would cause this?
I have a temporary fix right now, I've set the phone for static IP and entered all the values. It now connects to my home network on the correct IP and appears to work. This will be a hassle though because there will likely be conflicts when I try to connect to public wifi or at my office. I could just go in and set it back to automatic IP when I leave home....but that is a hassle, and obviously, something isn't working quite right.
Anybody have a clue what would be making this happen?
thanks!
theWilly said:
A couple of days ago my wireless connection quit working at home. The wireless network icon turned white all the time, and never switched to green. I hard wire the modem/router (ATT Uversre 2Wire 3800HGV-B) into a 5 port switch and plug my computer, network storage drive, and media streaming box into the switch. I've had all of this set up for a few months in it's current configuration and there was never an issue before. This just seemingly happened out of the blue...funny how computers do that sometimes, right? I have an HTC Aria, I was running CM7 RC1 when the problem happened, I just updated to RC2 hoping maybe it would change and it didn't.
After reading posts and checking settings here's what I've found:
My wireless router is set to act as the DHCP server. I set all of the IP addresses manually. I've had it set this way for some time, haven't made any changes recently. The attached network storage (D-Link DNS 323 also has DHCP server capability, but that is disabled)
I found that while my phone was set in the router's setting to connect to 192.168.1.67 for whatever reason it was connecting to 192.168.0.200 (which is out of range, my DHCP is set to address to 192.168.1.64 - 192.168.1.253)
Any idea what would cause this?
I have a temporary fix right now, I've set the phone for static IP and entered all the values. It now connects to my home network on the correct IP and appears to work. This will be a hassle though because there will likely be conflicts when I try to connect to public wifi or at my office. I could just go in and set it back to automatic IP when I leave home....but that is a hassle, and obviously, something isn't working quite right.
Anybody have a clue what would be making this happen?
thanks!
Click to expand...
Click to collapse
I don't understand when you say your router is your DHCP server but you set all the addresses manually...I can understand setting your network storage and media streaming to static IP's but you may want to reconsider for everything else, if your router allows for that to happen.
Have you tried rebooting your router and switch? May be worth doing that. I would not recommend a RESET because you'll have to reconfigure everything and I know how much of a hassle that is.
So, when you say you set the phone for static IP, do you mean through the phone gui or through the router?
Another thing to check is the number of available IP addresses. You could be out. I doubt this is the case in a home network, but never hurts to check.
"Do you mind if I turn up the AC?"
I have somewhat of a similar situation... I just installed CM7 RC2 and I can connect to my home's wifi and browse the internet etc... but some apps like Facebook won't update. With Facebook, I can retrieve messages sent to me but the news feed never updates and I can't view profiles. And for some reason everything works when I use my university's wifi...
corber22 said:
I have somewhat of a similar situation... I just installed CM7 RC2 and I can connect to my home's wifi and browse the internet etc... but some apps like Facebook won't update. With Facebook, I can retrieve messages sent to me but the news feed never updates and I can't view profiles. And for some reason everything works when I use my university's wifi...
Click to expand...
Click to collapse
Have you checked (turned on) your Background Data and Auto-sync?
Menu > Settings > Accounts & Sync ......
Have you checked (turned on) your Background Data and Auto-sync?
Menu > Settings > Accounts & Sync ......
Click to expand...
Click to collapse
Yeah, it's on. Still doesn't work. One other thing I noticed is that even though I'm with At&t the Amazon App Store works when I'm using my university's WiFi but no where else...
corber22 said:
Yeah, it's on. Still doesn't work. One other thing I noticed is that even though I'm with At&t the Amazon App Store works when I'm using my university's WiFi but no where else...
Click to expand...
Click to collapse
Go here and download the latest Nightly cm_liberty_full-30.zip
WiFi performance has been dramatically improved since RC2, and if nothing else, it's a better place to continue trouble shooting from.
Go here and download the latest Nightly cm_liberty_full-30.zip
WiFi performance has been dramatically improved since RC2, and if nothing else, it's a better place to continue trouble shooting from.
Click to expand...
Click to collapse
Didn't help I don't get what's happening. I can use the browser fine but certain applications always time out and won't update.
I have the same problem. I've found the following apps to not work correctly when I connect my Sprint HTC Evo 4G (CM 7.0.3.1) to my home wireless network (Apple Airport Extreme Base Station):
Facebook (news feed won't update)
Amazon MP3 (Only the cloud player doesn't work)
Netflix (won't let me log in)
Speedtest (downloads fine but shows 0.00Mbps for uploads)
Again, all features works great on 3G or on the wifi at work (a university network running WPA2 Enterprise with LEAP authentication), which leads me to suspect there's something wrong with my home wifi setup. I have updated the Airport Extreme to the latest firmware and reset it several times yet the problem persists. Any ideas?

X10 wifi SCANNING - DISCONNECTED loop! HELP!

Router information: Linksys Wireless-N WRT120N
I have done everything that i could think of to get this working. i have done several google searches and they all say to do specific things.
For example:
-Reset router
-Enable B/G only or G only set at channel 11
-turn off router firewall settings
-and a bunch of other random sh*t
i have done all of the above then some and i still cant get it to connect. all i get is *scanning* then *disconnected* thats the only two things it says. except right after i reset the router. every time i reset the router i get * obtaining IP yadadada* then goes to *disconnected* then back to the "scanning, disconnected" loop.
there have been some people that have said flashing a custom firmware on the router would fix the issue with mobile connectivity on Wireless-N routers.
please someone be helpful with this and please dont tell me i need to reset my router. i have asked this same question on several forums and the only replies i get are "if you reset the router and turn off security it WILL work fine" thats bull****. im not an idiot. thats the first step any computer literate person would take before asking questions.
**Update: same as from General thread. i had to repost because it was closed for some reason there. also here are the answers to the other two guys to responded.
"not standing close enough" -i have been standing next to it. i have yet to test it more than 10 feet away lol so it cant be there
"flash another rom or reflash current rom" -it has nothing to do with my rom, kernal, or radio. this issue is also happening on my girlfriends xperia running Wolfxperia and mine is the blackeditionHDv2. its also an issue with her sisters xperia. hers is still stock 2.2(i think). their stepdad has an iphone and it wont connect with that either. from what ive gathered... its a mobile issue. i know all these phones say (b or g only) but even setting the router to broadcast in b/g it still wont connect. it notices the routers name with full strength on all devices. also i might add that their laptop is an older laptop. does not support N but still can connect to the router and have internet.
Same here. Xperia mini x10 pro. When on it says connecting even thought I nothing appear visible.
Sent from my DesireS to your screen
Has it ever worked or it just not Working now? It happened to me before I reverted to stock and it worked
Sent from my X10S using XDA
*sorry for hijacking your post ts*
as for me it just started, before that when i was at col i was able to watsapp as usual, the phone is currently not with me but when i get i will post some ss for you to see.
-------------------------------
Here are the ss
any idea on how i can solve this?
I'm guessing this is an ip issue. The mobile devices are not able to get one. This usually happens to me on a public network and I even get a " limited or no connectivity".
The work around I do is to assign a static ip on my phone. Its very simple to do and if you need help doing it, let me know.
There's no clear explanation I can tell you, but it seems some mobile devices have a hard time pulling ip's from different types of routers. Hope this helps.
Sent from my X10 using Tapatalk
daniel.b said:
I'm guessing this is an ip issue. The mobile devices are not able to get one. This usually happens to me on a public network and I even get a " limited or no connectivity".
The work around I do is to assign a static ip on my phone. Its very simple to do and if you need help doing it, let me know.
There's no clear explanation I can tell you, but it seems some mobile devices have a hard time pulling ip's from different types of routers. Hope this helps.
Sent from my X10 using Tapatalk
Click to expand...
Click to collapse
Will ask my gf to give it a try. It happened so abruptly, it was working fine when she was at col then when she came back it won't detect any wifi, whether it's her house or mine, and now that she is back at her col she still can't connect.
I know how you feel.
I have had this issue ever since I first upgraded to Stock 2.3.3 last July. On 1.6 and 2.1 (both stock also) I never had issues.
Basically, in my case, resetting the router DOES solve the problem, but only for a limited time. This limited time is random, as sometimes it will work for a few days, and then sometimes it will cut out a few hours again after I have reset my router. I am also using the static IP method (and an app called WiFi Stat which I initially thought had solved the problem, but it hasn't) I'm not sure what triggers the WiFi connection to be lost, but there must be a trigger. Like I said, I never had this issue in my previous old Android versions.
I had hoped (somewhat naively) that moving to a custom ROM would solve the issue, but after installing Wolf's latest ROM, I still have this issue.
Have you tried anything based on 2.3.4 or above, to see if this is an Android 2.3.3 issue? Are there any good ROMs people could recommend that are based on higher versions than 2.3.3?
WEP/WPA key issue?
If its not the kernel/ROM/version of the phone, it could have something to do with the way the security is set up for your router. I had the most frustrating time logging into my university's wireless (think it was encrypted with 802.1x EAP) which required username and password. Though most home-owned router are equipped with WPA/WPA2 PSK or WEP, you can try the steps below:
1. Go to Settings ->Wi-Fi Settings -> Add Wi-Fi network
2. Type in the network SSID (yeah this is the manual part)
3. Open the "Security" drop-down box and set the following:
Security: 802.1x EAP
EAP method: PEAP (default)
Phase 2 auth.: MSCHAPV2
CA cert.: leave unchanged
User cert.: leave unchanged
4. Type in username (if any) and password.
Once again, this would work 99% for 802.1x...not sure about WPA/WEP. Good luck!
Try Channel 6 in router option and hope it works.
Solve
setting a static ip doesnt seem to work.. any idea? i wish not to re-flash as i dun think that would be a permanent solution.
again i dun think it has anything to do with my router as other gadgets are able to connect with it and i didnt fiddle with the security.
It is unable to detect any router as i have tried it different hotspots.
Hope to get some help.
------------------------------------
I wipe clear the settings and it worked again.. hope the problem doesn't persist again.

touchpad Android wireless issues sorted

Should probably go in development but as a noob I can't post their yet.
Since updating to CM7 A3.5 I started having wireless issues. Would lose IP connectivity but connection up. Other wireless devices no issues and previous CM7 versions had been okay.
Updated to Xron 2.91 on here which seemed to make things worse.
Ran a wifi signal app and noticed neighbours AP on the same channel. Reconfigured mine and have had no touchpad issues since.
As all other devices were fine I didn't think of checking the frequency. Obviously the touchpad is a bit sensitive.
Hope someone else benefits from this. Thanks to those who released the Xrom and CM7 roms. Makes the touchpad a wicked cheap tablet.
Matt.
This has been talked about before and is considered one way of fixing wifi problems. If you still can't connect you could make the touchpad forget the network from settings and reconnect again. Using an app like regpon wifi keep alive helps a lot and finally a reboot helps if everything else fails
Sent from my Touchpad using Tapatalk
Also: Make sure your date/time is correct and a reboot into webOS often fixes it.
Yeah the wifi issues seem to be a hit or miss. Sometimes changing the channel works for people. Other times it's just the router. I would need to always "forget" the connection before turning my TP off then reconnect after at my house. But it works perfectly at my friends house. Thanks for the post though. It might help others with this issue.
i was just going to actually post in the thread, but like you, i am a newb with insufficient rights =)
ive done 4 touchpads, 3 different routers, cm7 3.0/3.5 and xronified 2.1 and to 2.9:
-asus rt12n w/tomato 1.28 in WDS mode with WPA1 AES on channel 11:
runs flawlessly on every revision and touchpad ive done so far.
-airlink ar670w w/ddwrt sp1 with WPA2 AES on channel 11:
initially connects but when TP goes to sleep, it will not reconnect on wakeup and strobe on and off and lock up wifi settings. cm7 3.0/3.5 and xronified 2.7/8/9
-linksys wrt54g w/hyper thibor with WPA2 AES on channel 11:
same results the airlink with ddwrt
after searching and experimenting, ive gotten both the linksys and airlink to play nice by doing the following:
1) changed encryption from WPA2 to WPA1
2) changed channels to 6 or 1 (personally i just picked whatever seemed less crowded)
3) disabled wifi sleep and scanning on TP.
4) rebooted TP into webos then back into android and rebooted router.
hope one or some of these solutions helped.
Even if your other devices weren't having issues being on the same wifi channel can cause packet loss due to interference making your Internet feel slower.
I also read that people had succes using the FXR Wifi Fix app to fix some of their wifi issues. If anyone is still having issues, you might want to try that out as well.
Grizzy3 said:
I also read that people had succes using the FXR Wifi Fix app to fix some of their wifi issues. If anyone is still having issues, you might want to try that out as well.
Click to expand...
Click to collapse
how can u even download the app when ur wifi isint working
Toney Starks said:
how can u even download the app when ur wifi isint working
Click to expand...
Click to collapse
Download the apk and install manually from computer. just connect the touchpad to the computer and copy the file over.
The fxr app does restore my wifi connection, but does not permanently fix my disconnect issues. I am trying out the regpon app now, so hopefully this will help maintain my connections!
As far as messing with routers, this is not an option for me as I use my school's wifi network when I'm working in my lab.
I have only dropped once at home and after forgetting the network and reconnecting I never had trouble again.
First post here... Just want to say that this is an amazing community. So many cool heads willing to spend time to help. It's awesome. With guidance from many of you(I have done EXTENSIVE reading around here for days), I just did my first CM install on my TP and I am in heaven.
The solution I'very found is to tap the icon next to the back icon and then the wireless icon. Don't even know what the icons called, butit has buttons to turn. on/off wifi, Bluetooth, suond and what I'm assuming is the camera.

WiFi Disappeared

Have had my nook tablet for awhile now...started with cm7 alpha 1...no issues with wifi connecting to my hotspot, work wifi (non secured guest network) or my home wifi...as of today I'm on alpha final and I come home to no wifi. Only thing different I did today was connect to my works secured wifi and shut off my nook tablet after leaving work and turned it back on at home. If i do a wifi scan my home network doesn't even show up. Rebooted my router (its a linksys router running tomato firmware) laptop, ps3, wii, and my other computer all see the wifi just fine....nook tablet does not see it. Short of reloading the whole cm7 alpha final rom...any other ideas? I've tried turning wifi off waiting a minute then back on, wiping out any and all other wifi found (aka forgetting any wifi profiles) as well as rebooting the nook tablet. Can the nook tablet only handle one type of secured wifi profile?
And an hour later...I mysteriously can connect to my wifi....on a whim I did setup a static IP for my Android device (static dhcp option on router) so if by chance it does have to do with leases that should solve that issue
Sent from my Nook Tablet using Tapatalk
WiFi weirdness
I'm seeing some strange issue with my wifi connections also. Not exactly what you're seeing, but an oddity that's turned up recently. I'm running CyanogenMod-7.1.0. Which I believe is the latest "stable" version.
What I'm seeing is that occassionally the wifi will lose connection and go into a "Turning Off" state that requires a hard power off (hold down power button for 10-15 seconds) and power back on (hold down power button for 5 seconds). This clears up my problem until it happens again. This seems to be fairly new, IE in the last week or so.
I'm connecting to different secured networks in the course of a day. IE several different work encrypted/open hot spots/networks and then a WPA secured wifi at home. Now I'm wondering if what I'm seeing is similar to you, in that the change in profiles is causing the lock up. I'll test it some and see if I notice a pattern.
having the same problem as you
Excessiveidling said:
And an hour later...I mysteriously can connect to my wifi....on a whim I did setup a static IP for my Android device (static dhcp option on router) so if by chance it does have to do with leases that should solve that issue
Sent from my Nook Tablet using Tapatalk
Click to expand...
Click to collapse
I've been experiencing the same exact thing lately on my 8GB NT running cm7 alpha via sandisk sd card. Sometimes the wifi works great and then suddenly it stops working completely and the wifi on the nook doesn't show ANY wifi networks (ordinarily there will be 20 from neighbors, etc. at any given time). I have tried the turning off, rebooting, removing/forgetting, etc. and nothing brings it back. Until it randomly just returns on its own. This time, however, as of yesterday, the wifi is not "seeing" any other networks at all and it's just staying in that state. I'm at a loss about how to bring it back.
Any ideas??
I was going to say, "CM7 beta now works on the 8GB", but then I see that CelticWebSolution's post says it's internal...
Hmmm, then does succulent's CM7 beta for 8 go on a card ? ? ? . . I think that raywaldo was playing with that ? you could PM him. He is a very nice and helpful person. ( if they were handing out awards... he'd get one ! )
http://forum.xda-developers.com/showthread.php?t=1545766
.
Then there is the adage, "when in doubt, wipe it out". This rule is "ONLY" true when it is relatively easy to re-create the end result ( card ).
old_fart said:
.
Then there is the adage, "when in doubt, wipe it out". This rule is "ONLY" true when it is relatively easy to re-create the end result ( card ).
Click to expand...
Click to collapse
Thanks.
Yeah...I've previously wiped it out and reinstalled it like 3 times already. Not hard to do...just inconvenient. I suppose that'll be my next step unless someone responds soon with a more permanent solution.
I have had similar problems running CM7 from an SD card. When the NT will not "see" a network that I know is there, I have found that deleting remembered Wireless Networks fixes the problem. I haven't taken the time to figure out why, I just know it works.

[Q] Aussie McDonalds WiFi?

So I was trying to browse internet at a McD restaurant the other day and couldn't get my prime to redirect to McD splashscreen. Tried various browsers......opera, dolphin, stock, chrome and none of them would redirect. Used wifi tool and confirmed an ip address had been issued but the wifi fan would just stay grey. Dhcp settings checked, must admit I haven't tried another mcD location but just wanted to confirm whether others in Oz are able to bring up the sign in splashscreen with their primes running latest stock ICS.
Two Thoughts....If the McD's router is using the AD-HOC mode, you need the fix that's shown in the forum (or wait for update 19/20 - it's supposed to be in there)
2nd, At times, the only way I can get my Prime to work with Wifi is to reboot the router....Wifi Analyzer shows the signal there, but even shutting the Prime down, and restarting, wont work.....then I reboot the router and everything is fine.
I have no idea of what modes the Free Wifi Hotspots use
Thanks, now that you mention it I did already change the wpa_supplicant file some months ago as mentioned in this forum, I wonder if thats what is causing connex issues with mcD`s. Will try with original nxt time.

Categories

Resources