I'm stuck.
I cant get into RSD mode cause when I hold vol up it just goes into fastboot.
IF I vol down it just blinks and turns off...
What are my options.
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Do you know how to go into android recovery and do a factory reset?
KurioHonoo said:
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Click to expand...
Click to collapse
Its just sitting at "Failed to boot 1"
bijan588 said:
Its just sitting at "Failed to boot 1"
Click to expand...
Click to collapse
Try pulling the battery and put it back in with the phone off plug in your wall charger and see if your recovery comes up
What were u trying to do before this happened?
*****Have u tried a fully charged battery?*****
failed to boot = sbf time
no big deal
skwoodwiva said:
failed to boot = sbf time
no big deal
Click to expand...
Click to collapse
U can't sbf if u can't start rsd protocol
my bad
wow do we have a real one?
if I remember well it would always say failed to boot 2 and rsd would be available .
Is this a Dx2?
Apparently he is getting a failed to boot 1 ..I think I remember seeing this before.
It might be in one of the.older sbf tutorial threads...myabe the one by dag425.
It would be helpful (maybe) to know what was being done that caused this to happen.
Hopefully he wasn't messing with bootloader partitions and signatures or something. I think that would he just about the only thing that could hard brick us.
Sent from my DROID X2 using XDA App
Could it just be hardware failure?
We wont know anything til the OP comes back and give more info on situation
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
LordRalh3 said:
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
Click to expand...
Click to collapse
I'm assuming he meant power+up.
Sent from my MB870 using xda premium
If u hold power and volume up it takes u directly into "starting RSD protocol "
it is the method I have ALWAYS used when flashing sbf
I am stuck here too! I only have two options:
1: fastboot
or
2: nvflash
I have no idea what the hell eather one does so any little help is greatly appreciated for this noob. Thanks in advance...
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
skwoodwiva said:
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
Click to expand...
Click to collapse
yeah thats what i used to get to android recovery and rsd protocol and stuff. this time i can only do fastboot and nvflash. i am also stuck at the failed to boot 1 on boot. Also, it will only turn on when connected to pc/wallcharger...thank you for helping as my problem is the exact same as his. any more info needed just ask. i will try to reply quickly and fix this for both of us
Edit: this is dx2
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
skwoodwiva said:
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
Click to expand...
Click to collapse
was messing with settings in BSR idk what it was:
eather
1. clean boot files or whatever
or
2. partition sd card
i think it was the partition sd card part. cuz after that the option to go back went away...very odd. did a batt pull and then got failed to boot 1. i think im gonna have to take it to vzw and hope the guys an idiot
Related
I hold the power button and volume button down what do I do to go in recovery I can't just turn the phone on I messed it up and it stays on Motorola dual core that's it
I have tried fastboot, and other RSS, and no recovery please help before I smash the phone thank you
alusher said:
I hold the power button and volume button down what do I do to go in recovery I can't just turn the phone on I messed it up and it stays on Motorola dual core that's it
I have tried fastboot, and other RSS, and no recovery please help before I smash the phone thank you
Click to expand...
Click to collapse
####should be in general or Q & A section####
once you see the fastboot at the top you have to scroll down untill you see android recovery. volume down until you see it. then volume up to enter. then you will get the droid and triangle, hit both volume up and down and the menu will op
**edit** this is the stock recovery, not recovery used to flash roms and create NAND backups.
Must have your phone plugged into the wall charger and not a USB connected device like a PC.
Pfilly said:
Must have your phone plugged into the wall charger and not a USB connected device like a PC.
Click to expand...
Click to collapse
this is true for BSR system recovery, for stock android recovery you do not need to be plugged in.
U might need to sbf if ur phone can't get into bootstrap via powerdown and plugging in.
or if a data wipe from Android stock recovery doesn't help.
There is a very nice tutorial on how to do it...a couple of em....one is a sticky so its easy to find...
ashclepdia said:
U might need to sbf if ur phone can't get into bootstrap via powerdown and plugging in.
or if a data wipe from Android stock recovery doesn't help.
There is a very nice tutorial on how to do it...a couple of em....one is a sticky so its easy to find...
Click to expand...
Click to collapse
I think he's trying to get into stock recovery.
I have the the SBF thing down, I could do it in my sleep! Haha
Too many mess ups from being a n00b. I can't seem to escape it
Sent from my DROID X2 using XDA App
IDMA.DROID.X2 said:
I think he's trying to get into stock recovery.
I have the the SBF thing down, I could do it in my sleep! Haha
Too many mess ups from being a n00b. I can't seem to escape it
Sent from my DROID X2 using XDA App
Click to expand...
Click to collapse
Yeah...sbf isn't really that complicated...especially once u have all files/programs u need already installed it really.is only a 15min process depending on computer speed.
I use my sisters computer and the flash is done within 10minutes every time...
And yeah after rereading the op I also think they were looking for stock recovery.
Power and volume down. Then scroll wit volume down til u see android recovery. Then volume up to enter.
Once.u see triangle &exclamation point press volume up&down together. Presto.
But even still. Every time I have been stuck at M logo I needed to sbf...no amount of data wipes would help me...especially the first time it happen to me since I deleted init and build.prop. DURP! Lol
ashclepdia said:
Yeah...sbf isn't really that complicated...especially once u have all files/programs u need already installed it really.is only a 15min process depending on computer speed.
I use my sisters computer and the flash is done within 10minutes every time...
And yeah after rereading the op I also think they were looking for stock recovery.
Power and volume down. Then scroll wit volume down til u see android recovery. Then volume up to enter.
Once.u see triangle &exclamation point press volume up&down together. Presto.
But even still. Every time I have been stuck at M logo I needed to sbf...no amount of data wipes would help me...especially the first time it happen to me since I deleted init and build.prop. DURP! Lol
Click to expand...
Click to collapse
Haha, I deleted framework and systemui and f'd it up! Should have done a nandroid and I would have been fine haha
Sent from my DROID X2 using XDA App
I had tried to flash the stock webtop on my atrix 4g, after i had done the webtop mod(due to the screen presses from the phone would not work, and it also would not allow me to have the normal functionality and so i wanted to go back to stock for webtop). Not too sure if I'm able to post the link to where i found the instructions, but i did get it from atrix forums.
But pretty much now, when i turn my phone on, it gets stuck on the Motorola screen with text saying...
Failed to boot 4
Starting RSD Mode
I did read up and saw that from my POV, the best thing would be to get the stock sbf and use RSD Lite and flash it back to the beginning. But a few things do come up,
I found a thread in XDA where it had all the sbf i could want, but they were uploaded into filesonic which will not let me download it.
Would this be the only option for me to go?
Also some background into phone, AT&T Atrix 4g, was running 2.3.4, firmware 4.5.91 and was rooted. Any enlightenment on my pridicament would be much appreciated. Thank you for your time in reading.
First, did you have an unlocked bootloader?
If not, that's your problem.
Second, is there an option to get into recovery?
If so, try to perform a "Factory Reset" within the recovery before trying to use RSD lite (not recommended).
Dilphat said:
I had tried to flash the stock webtop on my atrix 4g, after i had done the webtop mod(due to the screen presses from the phone would not work, and it also would not allow me to have the normal functionality and so i wanted to go back to stock for webtop). Not too sure if I'm able to post the link to where i found the instructions, but i did get it from atrix forums.
But pretty much now, when i turn my phone on, it gets stuck on the Motorola screen with text saying...
Failed to boot 4
Starting RSD Mode
I did read up and saw that from my POV, the best thing would be to get the stock sbf and use RSD Lite and flash it back to the beginning. But a few things do come up,
I found a thread in XDA where it had all the sbf i could want, but they were uploaded into filesonic which will not let me download it.
Would this be the only option for me to go?
Also some background into phone, AT&T Atrix 4g, was running 2.3.4, firmware 4.5.91 and was rooted. Any enlightenment on my pridicament would be much appreciated. Thank you for your time in reading.
Click to expand...
Click to collapse
unlocked bootloader, that would be a negative. I guess that was what happened as to why i'm in this situation. But trying to get it back to factory settings, when i turn on the phone and hold down power button and vol down, it shows the Motorolla screen, i keep holding it down...it never shows the option for fast boot or the menu to change to be able to get it back to factory. Unless I'm doing it wrong, but it goes to Motorola screen then waits a bit and then screen turns off. Any ideas? If RSD Lite is not recommended, what's a good try to take? thanks for replying back quite fast.
Just to confirm the steps:
1. Press and hold the volume down button
2. Then press the power button (note: you don't need to continue holding the power button when doing this)
3. Continue holding the volume down button until it says "Fastboot"
If that's what you did then that would be correct. Actually, try just booting it normally and see if it gives you any options while booting.
Dilphat said:
unlocked bootloader, that would be a negative. I guess that was what happened as to why i'm in this situation. But trying to get it back to factory settings, when i turn on the phone and hold down power button and vol down, it shows the Motorolla screen, i keep holding it down...it never shows the option for fast boot or the menu to change to be able to get it back to factory. Unless I'm doing it wrong, but it goes to Motorola screen then waits a bit and then screen turns off. Any ideas? If RSD Lite is not recommended, what's a good try to take? thanks for replying back quite fast.
Click to expand...
Click to collapse
When I let it boot up without pressing anything, it just says
"Failed to boot 4"
"Starting RSD mode"
When i hold down vol down button for a bit nothing. I did notice though if i press the vol down button directly after i get "failed to boot 4" it blinks something real quick and then the screen goes black(which then i would have to take out the battery and put the batter back in). ...but what flashes, i believes says nvflash.
If i press volume up button after it says "Failed to boot 4" it gives me..
"Starting Fastboot protocal support"
So with no touch, "Starting RSD mode".
Vol down, I think it says nvflash
Vol up, Starting fastboot protocal support.
Well, when it says "Starting Fastboot protocol support" it means it is in fastboot but I don't know for sure what you could do from other than "fastboot -w" which would erase userdata and cache. Do you have the fastboot files? Have you thought about trying to flash Pudding if you can get it into RSD mode? You could then flash a custom recovery in fastboot from that point and either try to factory reset or flash a custom rom/fruitcake.
Dilphat said:
When I let it boot up without pressing anything, it just says
"Failed to boot 4"
"Starting RSD mode"
When i hold down vol down button for a bit nothing. I did notice though if i press the vol down button directly after i get "failed to boot 4" it blinks something real quick and then the screen goes black(which then i would have to take out the battery and put the batter back in). ...but what flashes, i believes says nvflash.
If i press volume up button after it says "Failed to boot 4" it gives me..
"Starting Fastboot protocal support"
So with no touch, "Starting RSD mode".
Vol down, I think it says nvflash
Vol up, Starting fastboot protocal support.
Click to expand...
Click to collapse
So what are the chances of me getting a hard brick if i did the RSD Lite as what was proposed in other occurences?
Also with pudding, do I need anything done special on the phone...unlock bootloader or anything else? just want to make sure, since i don't want to be in this situation again or worse lol.
Also, what do you mean by if i have the fastboot files? such as the ones i used to root the phone?
There's really no measurement of risk for using RSD lite. If used properly it should go without a hitch but there have been "rare" occurrences of things going wrong. If you can find the correct sbf(2.3.4-4.5.91 signed) and download the current RSD then you should be fine
Pudding is the unlocked bootloader.
Fastboot files is what is needed to give commands in fastboot mode. (eg. "fastboot.exe")
Dilphat said:
So what are the chances of me getting a hard brick if i did the RSD Lite as what was proposed in other occurences?
Also with pudding, do I need anything done special on the phone...unlock bootloader or anything else? just want to make sure, since i don't want to be in this situation again or worse lol.
Also, what do you mean by if i have the fastboot files? such as the ones i used to root the phone?
Click to expand...
Click to collapse
is it that hard to find a signed sbf for 2.3.4 4.5.91 at&t?
Also, what would be the benefits of going the pudding way versus if i just attempt the rsd way?
which one is safer? lol
Pudding, in a sense, is safer as it will unlock your bootloader and you can flash ROMs all day with a custom recovery but it would help to have the appropriate knowledge before diving in. You mentioned you had rooted your phone but what else, as far as modding, are you familiar with?
I actually tried to find an sbf to link to for you but couldn't find one.
Dilphat said:
is it that hard to find a signed sbf for 2.3.4 4.5.91 at&t?
Also, what would be the benefits of going the pudding way versus if i just attempt the rsd way?
which one is safer? lol
Click to expand...
Click to collapse
well this atrix 4g is my first android based phone. As far as modding, i came from the winmo scene. from a fuze to tilt 2 to this atrix. thanks for actually trying to look for a sbf, i was able to find one not on filesonic...
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
but just not sure if it is the appropriate one needed. also, while i was at work, i did try and see what i could find on pudding and found a thread in regards to it, but nothing too much in detail about it. except for a if you don't understand any of the top 3 reasons then do this lol.
live4nyy said:
Pudding, in a sense, is safer as it will unlock your bootloader and you can flash ROMs all day with a custom recovery but it would help to have the appropriate knowledge before diving in. You mentioned you had rooted your phone but what else, as far as modding, are you familiar with?
I actually tried to find an sbf to link to for you but couldn't find one.
Click to expand...
Click to collapse
And what i'm getting when looking up pudding is this...
http://forum.xda-developers.com/showthread.php?t=1136261
and it looks like i still have to run rsd lite o_0, i'm so confused lol
Dilphat said:
well this atrix 4g is my first android based phone. As far as modding, i came from the winmo scene. from a fuze to tilt 2 to this atrix. thanks for actually trying to look for a sbf, i was able to find one not on filesonic...
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
but just not sure if it is the appropriate one needed. also, while i was at work, i did try and see what i could find on pudding and found a thread in regards to it, but nothing too much in detail about it. except for a if you don't understand any of the top 3 reasons then do this lol.
Click to expand...
Click to collapse
Failed to boot 4
Just in case someone else get's this error.
I used this sbf. at&t signed 2.3.4 4.5.91
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
and RSD Lite v5.6
From there when phone got to the motorola screen and said
"Failed to boot 4"
"Starting RSD Mode"
ran RSD with the sbf, it went through it's thing and it worked. it did revert everything that was done when the phone was rooted, and there is no root.
BTW, thanks for the help live4nyy!
live4nyy said:
There's really no measurement of risk for using RSD lite. If used properly it should go without a hitch but there have been "rare" occurrences of things going wrong. If you can find the correct sbf(2.3.4-4.5.91 signed) and download the current RSD then you should be fine
Pudding is the unlocked bootloader.
Fastboot files is what is needed to give commands in fastboot mode. (eg. "fastboot.exe")
Click to expand...
Click to collapse
edit* got the phone rooted again. now my problem is, webtop is gone lol. any thoughts on how to reinstall it?
Weird, the SBF file should of had that included. How big(MB) was the SBF file?
Dilphat said:
edit* got the phone rooted again. now my problem is, webtop is gone lol. any thoughts on how to reinstall it?
Click to expand...
Click to collapse
after extracted it is 1.46gb
live4nyy said:
Weird, the SBF file should of had that included. How big(MB) was the SBF file?
Click to expand...
Click to collapse
That sounds about right. How are you trying to access webtop? Do you have a lapdock or are you trying to just plug it into a monitor with the HDMI cable?
Dilphat said:
after extracted it is 1.46gb
Click to expand...
Click to collapse
I just figured out what i did wrong, i didn't have my hd multimedia dock plugged in lol
live4nyy said:
That sounds about right. How are you trying to access webtop? Do you have a lapdock or are you trying to just plug it into a monitor with the HDMI cable?
Click to expand...
Click to collapse
Major "derpage"...
Glad you got it working.
Dilphat said:
I just figured out what i did wrong, i didn't have my hd multimedia dock plugged in lol
Click to expand...
Click to collapse
I know right, and yup...I'm glad I got it working as well. but yup, in case it happens to anyone else, i put up the link to the sbf. just in case lol.
Now this gives me time to read up into unlocking the bootloader and flashing roms
live4nyy said:
Major "derpage"...
Glad you got it working.
Click to expand...
Click to collapse
I just flash from RSD lite... and it's fail.... (maybe because of low battery power)
I already recharge the battery full using external charger...
But now... mu photon Bricked.. I can't start the RSD mode (Power + Vol Down)
is there still any chance for it?
Thanks b4
Have you tried power + up? Does it give you any options when trying it? And are you in a boot loop or stuck at dual core screen?
Sent from my MB855 using XDA
hyem said:
I just flash from RSD lite... and it's fail.... (maybe because of low battery power)
I already recharge the battery full using external charger...
But now... mu photon Bricked.. I can't start the RSD mode (Power + Vol Down)
is there still any chance for it?
Thanks b4
Click to expand...
Click to collapse
Can you describe what the phone does? Does it turn on?
Sent from my Photon
I believe, the RSD mode is [Power+Vol Up].
In any case, take out your battery and reinsert it.
Press [Power+Vol Up] as soon as you insert the battery.
Report back on what happens.
Spmeone has tp unlock the boatloader for 2.3.5 in order to go back to sprint sbf. I woulnt get my hopes up if i were you
melon69 said:
Spmeone has tp unlock the boatloader for 2.3.5 in order to go back to sprint sbf. I woulnt get my hopes up if i were you
Click to expand...
Click to collapse
? What? Unless I missed something I never recall op stating anything about flashing 2.3.5. Anyway, any progress on getting phone into RSD?
Sent from my MB855 using XDA
Try this step.
1. Connect your photon and PC/Laptop.
2. Press RSD protocol (volume up + power)
See if this work.
Was i has same problem, failed when flashing using rsdlite (when entering bp passthough), when try to enter rsd protocol, its just stuck on moto logo. But when i try to connect it with pc/laptop and try again entering rsd protocol, its work.
My device is: Motorola atrix 4g mb860 AT&T.
I used my phone as usual, and it seemed it went out of battery (possibly), when I tried to power it up it said:
"Failed to boot 2
Starting RSD mode" and got stuck, however, if I take out the battery and try to power it up again it will show the same issue, I cant enter the fastboot protocol support if powering it up while holding the volume up key, it just stucks, I cant either enter the selection of modes if powering it up while holding the volume down key way, it brings me to a black screen.
Ive read about this RSD Light and stuff, tried to flash 3 different sbf files, or more, after trying to flash it shows this in the device:
"Failed to boot 2
Starting RSD mode
sec_exception febe 35, 35", the phone get stucked, and in the program it says "FAILED" under the tab "Result", however, it happens only after the status of the phone in the program "Waiting for re-enumeration" changes to "Failed flashing process. Phone[0000]; Phone did not re-enumerate after RAM-downloader was sent. (0x703E)".
When i take the cable of the phone out and do a restart to it, I'm back to the first problem at the beginning, Failed to boot 2, Starting RSD mode.
It seems someone had a samiliar problem to me, but he used clocked and stuff... his thread:
http:/ /ww w.atrixforums.com/forum/rescue-squad/6164-se-flash-olympus-help.html
DELETE SPACES.
Waiting for answers, thanks anyway, and have a good day, Matan.
Sorry mate,sounds like a soft brick.
you can try flashing a stock SBF
Well can you help me with this?
BoriDe said:
Sorry mate,sounds like a soft break.
you can try flashing a stock SBF
Click to expand...
Click to collapse
well, then can you help me get these files? i used mine SBF files and didn't worked, maybe yours will.
I'll try your SBF files if needed.
mtnjustme said:
well, then can you help me get these files? i used mine SBF files and didn't worked, maybe yours will.
I'll try your SBF files if needed.
Click to expand...
Click to collapse
I´m in the same problem here, did you get out of this trouble ?
iddpioneer said:
I´m in the same problem here, did you get out of this trouble ?
Click to expand...
Click to collapse
Search das8nt on yahoo or something, you'll find it. Or just simply run a search for atrix sbf instead of being lazy
Sent from my MB860 using xda app-developers app
As the title says:
My phone: Motorola Razr Maxx / xt910
I have used 3.65 but i decided to update to 3.73 along since i hopped to CM11 M9 from CM11 M7
This is where my problems started.
I made a new partition, and activated it as "active" one.
I installed CM11 M9 onto it, and google apps after that.
I booted to the new system and setup my apps and everything was fine, then i shut down the phone.
After i re-started the phone today it was stuck on motorola dual core technology logo. (which happens before safestrap).
And i managed to get into bootloader and deleted the CM11 M9 partition and switched back to stock rom as active one.
Then i attempted to re-create the partition and when it was doing the partition, the phone went off (still had 96% battery left).
After starting the phone up again, it's stuck on infinite boot loop, and flashes the green safestrap BIOS for half a second.
Is there any way i can fix my phone?
Try to flash it with RSD Lite, but its loss of data :/
Thank you for answering
archie1988 said:
Try to flash it with RSD Lite, but its loss of data :/
Click to expand...
Click to collapse
That is least of my worries And i got all data backed up pretty well
Is there any step by step tutorial for this?
stefeman said:
Thank you for answering
That is least of my worries And i got all data backed up pretty well
Is there any step by step tutorial for this?
Click to expand...
Click to collapse
Go here: http://forum.xda-developers.com/showthread.php?t=2155576
And scroll to video named undbrick/restore/unroot via rsd lite.
On the first page [emoji6]
archie1988 said:
Go here: http://forum.xda-developers.com/showthread.php?t=2155576
And scroll to video named undbrick/restore/unroot via rsd lite.
On the first page [emoji6]
Click to expand...
Click to collapse
I can't even get to AP Fastboot.. the safestrap flashes upper area and ****s up before that
Enough with this ****.. I'll bring this **** to my ISP and pay something so they null it and re-install stock system..
Lesson of the day.. don't update safestrap lol
stefeman said:
I can't even get to AP Fastboot.. the safestrap flashes upper area and ****s up before that
Click to expand...
Click to collapse
Turn off the phone and while it's off press vol- vol+ and the power button at the same time.
If you do it right,you shouldn't see anything related to SS.
Sent from my Razr XT910
welder73 said:
Turn off the phone and while it's off press vol- vol+ and the power button at the same time.
If you do it right,you shouldn't see anything related to SS.
Sent from my Razr XT910
Click to expand...
Click to collapse
Done that multiple times and the screen just flashes on upper area of the screen and goes off..
I can't even power it on without plugging in a charger first.. If i unplug charger it flashes and goes off..
The battery is close to 96-98%
stefeman said:
Done that multiple times and the screen just flashes on upper area of the screen and goes off..
I can't even power it on without plugging in a charger first.. If i unplug charger it flashes and goes off..
The battery is close to 96-98%
Click to expand...
Click to collapse
What about the led light,is it white?
If it's white then your battery is too low,you must buy or make the factory cable to be able to flash the fastboot with Rsd lite.
Sent from my Razr XT910
welder73 said:
What about the led light,is it white?
If it's white then your battery is too low,you must buy or make the factory cable to be able to flash the fastboot with Rsd lite.
Sent from my Razr XT910
Click to expand...
Click to collapse
Led light is never shown.. =/