Related
I'm stuck.
I cant get into RSD mode cause when I hold vol up it just goes into fastboot.
IF I vol down it just blinks and turns off...
What are my options.
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Do you know how to go into android recovery and do a factory reset?
KurioHonoo said:
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Click to expand...
Click to collapse
Its just sitting at "Failed to boot 1"
bijan588 said:
Its just sitting at "Failed to boot 1"
Click to expand...
Click to collapse
Try pulling the battery and put it back in with the phone off plug in your wall charger and see if your recovery comes up
What were u trying to do before this happened?
*****Have u tried a fully charged battery?*****
failed to boot = sbf time
no big deal
skwoodwiva said:
failed to boot = sbf time
no big deal
Click to expand...
Click to collapse
U can't sbf if u can't start rsd protocol
my bad
wow do we have a real one?
if I remember well it would always say failed to boot 2 and rsd would be available .
Is this a Dx2?
Apparently he is getting a failed to boot 1 ..I think I remember seeing this before.
It might be in one of the.older sbf tutorial threads...myabe the one by dag425.
It would be helpful (maybe) to know what was being done that caused this to happen.
Hopefully he wasn't messing with bootloader partitions and signatures or something. I think that would he just about the only thing that could hard brick us.
Sent from my DROID X2 using XDA App
Could it just be hardware failure?
We wont know anything til the OP comes back and give more info on situation
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
LordRalh3 said:
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
Click to expand...
Click to collapse
I'm assuming he meant power+up.
Sent from my MB870 using xda premium
If u hold power and volume up it takes u directly into "starting RSD protocol "
it is the method I have ALWAYS used when flashing sbf
I am stuck here too! I only have two options:
1: fastboot
or
2: nvflash
I have no idea what the hell eather one does so any little help is greatly appreciated for this noob. Thanks in advance...
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
skwoodwiva said:
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
Click to expand...
Click to collapse
yeah thats what i used to get to android recovery and rsd protocol and stuff. this time i can only do fastboot and nvflash. i am also stuck at the failed to boot 1 on boot. Also, it will only turn on when connected to pc/wallcharger...thank you for helping as my problem is the exact same as his. any more info needed just ask. i will try to reply quickly and fix this for both of us
Edit: this is dx2
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
skwoodwiva said:
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
Click to expand...
Click to collapse
was messing with settings in BSR idk what it was:
eather
1. clean boot files or whatever
or
2. partition sd card
i think it was the partition sd card part. cuz after that the option to go back went away...very odd. did a batt pull and then got failed to boot 1. i think im gonna have to take it to vzw and hope the guys an idiot
I had tried to flash the stock webtop on my atrix 4g, after i had done the webtop mod(due to the screen presses from the phone would not work, and it also would not allow me to have the normal functionality and so i wanted to go back to stock for webtop). Not too sure if I'm able to post the link to where i found the instructions, but i did get it from atrix forums.
But pretty much now, when i turn my phone on, it gets stuck on the Motorola screen with text saying...
Failed to boot 4
Starting RSD Mode
I did read up and saw that from my POV, the best thing would be to get the stock sbf and use RSD Lite and flash it back to the beginning. But a few things do come up,
I found a thread in XDA where it had all the sbf i could want, but they were uploaded into filesonic which will not let me download it.
Would this be the only option for me to go?
Also some background into phone, AT&T Atrix 4g, was running 2.3.4, firmware 4.5.91 and was rooted. Any enlightenment on my pridicament would be much appreciated. Thank you for your time in reading.
First, did you have an unlocked bootloader?
If not, that's your problem.
Second, is there an option to get into recovery?
If so, try to perform a "Factory Reset" within the recovery before trying to use RSD lite (not recommended).
Dilphat said:
I had tried to flash the stock webtop on my atrix 4g, after i had done the webtop mod(due to the screen presses from the phone would not work, and it also would not allow me to have the normal functionality and so i wanted to go back to stock for webtop). Not too sure if I'm able to post the link to where i found the instructions, but i did get it from atrix forums.
But pretty much now, when i turn my phone on, it gets stuck on the Motorola screen with text saying...
Failed to boot 4
Starting RSD Mode
I did read up and saw that from my POV, the best thing would be to get the stock sbf and use RSD Lite and flash it back to the beginning. But a few things do come up,
I found a thread in XDA where it had all the sbf i could want, but they were uploaded into filesonic which will not let me download it.
Would this be the only option for me to go?
Also some background into phone, AT&T Atrix 4g, was running 2.3.4, firmware 4.5.91 and was rooted. Any enlightenment on my pridicament would be much appreciated. Thank you for your time in reading.
Click to expand...
Click to collapse
unlocked bootloader, that would be a negative. I guess that was what happened as to why i'm in this situation. But trying to get it back to factory settings, when i turn on the phone and hold down power button and vol down, it shows the Motorolla screen, i keep holding it down...it never shows the option for fast boot or the menu to change to be able to get it back to factory. Unless I'm doing it wrong, but it goes to Motorola screen then waits a bit and then screen turns off. Any ideas? If RSD Lite is not recommended, what's a good try to take? thanks for replying back quite fast.
Just to confirm the steps:
1. Press and hold the volume down button
2. Then press the power button (note: you don't need to continue holding the power button when doing this)
3. Continue holding the volume down button until it says "Fastboot"
If that's what you did then that would be correct. Actually, try just booting it normally and see if it gives you any options while booting.
Dilphat said:
unlocked bootloader, that would be a negative. I guess that was what happened as to why i'm in this situation. But trying to get it back to factory settings, when i turn on the phone and hold down power button and vol down, it shows the Motorolla screen, i keep holding it down...it never shows the option for fast boot or the menu to change to be able to get it back to factory. Unless I'm doing it wrong, but it goes to Motorola screen then waits a bit and then screen turns off. Any ideas? If RSD Lite is not recommended, what's a good try to take? thanks for replying back quite fast.
Click to expand...
Click to collapse
When I let it boot up without pressing anything, it just says
"Failed to boot 4"
"Starting RSD mode"
When i hold down vol down button for a bit nothing. I did notice though if i press the vol down button directly after i get "failed to boot 4" it blinks something real quick and then the screen goes black(which then i would have to take out the battery and put the batter back in). ...but what flashes, i believes says nvflash.
If i press volume up button after it says "Failed to boot 4" it gives me..
"Starting Fastboot protocal support"
So with no touch, "Starting RSD mode".
Vol down, I think it says nvflash
Vol up, Starting fastboot protocal support.
Well, when it says "Starting Fastboot protocol support" it means it is in fastboot but I don't know for sure what you could do from other than "fastboot -w" which would erase userdata and cache. Do you have the fastboot files? Have you thought about trying to flash Pudding if you can get it into RSD mode? You could then flash a custom recovery in fastboot from that point and either try to factory reset or flash a custom rom/fruitcake.
Dilphat said:
When I let it boot up without pressing anything, it just says
"Failed to boot 4"
"Starting RSD mode"
When i hold down vol down button for a bit nothing. I did notice though if i press the vol down button directly after i get "failed to boot 4" it blinks something real quick and then the screen goes black(which then i would have to take out the battery and put the batter back in). ...but what flashes, i believes says nvflash.
If i press volume up button after it says "Failed to boot 4" it gives me..
"Starting Fastboot protocal support"
So with no touch, "Starting RSD mode".
Vol down, I think it says nvflash
Vol up, Starting fastboot protocal support.
Click to expand...
Click to collapse
So what are the chances of me getting a hard brick if i did the RSD Lite as what was proposed in other occurences?
Also with pudding, do I need anything done special on the phone...unlock bootloader or anything else? just want to make sure, since i don't want to be in this situation again or worse lol.
Also, what do you mean by if i have the fastboot files? such as the ones i used to root the phone?
There's really no measurement of risk for using RSD lite. If used properly it should go without a hitch but there have been "rare" occurrences of things going wrong. If you can find the correct sbf(2.3.4-4.5.91 signed) and download the current RSD then you should be fine
Pudding is the unlocked bootloader.
Fastboot files is what is needed to give commands in fastboot mode. (eg. "fastboot.exe")
Dilphat said:
So what are the chances of me getting a hard brick if i did the RSD Lite as what was proposed in other occurences?
Also with pudding, do I need anything done special on the phone...unlock bootloader or anything else? just want to make sure, since i don't want to be in this situation again or worse lol.
Also, what do you mean by if i have the fastboot files? such as the ones i used to root the phone?
Click to expand...
Click to collapse
is it that hard to find a signed sbf for 2.3.4 4.5.91 at&t?
Also, what would be the benefits of going the pudding way versus if i just attempt the rsd way?
which one is safer? lol
Pudding, in a sense, is safer as it will unlock your bootloader and you can flash ROMs all day with a custom recovery but it would help to have the appropriate knowledge before diving in. You mentioned you had rooted your phone but what else, as far as modding, are you familiar with?
I actually tried to find an sbf to link to for you but couldn't find one.
Dilphat said:
is it that hard to find a signed sbf for 2.3.4 4.5.91 at&t?
Also, what would be the benefits of going the pudding way versus if i just attempt the rsd way?
which one is safer? lol
Click to expand...
Click to collapse
well this atrix 4g is my first android based phone. As far as modding, i came from the winmo scene. from a fuze to tilt 2 to this atrix. thanks for actually trying to look for a sbf, i was able to find one not on filesonic...
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
but just not sure if it is the appropriate one needed. also, while i was at work, i did try and see what i could find on pudding and found a thread in regards to it, but nothing too much in detail about it. except for a if you don't understand any of the top 3 reasons then do this lol.
live4nyy said:
Pudding, in a sense, is safer as it will unlock your bootloader and you can flash ROMs all day with a custom recovery but it would help to have the appropriate knowledge before diving in. You mentioned you had rooted your phone but what else, as far as modding, are you familiar with?
I actually tried to find an sbf to link to for you but couldn't find one.
Click to expand...
Click to collapse
And what i'm getting when looking up pudding is this...
http://forum.xda-developers.com/showthread.php?t=1136261
and it looks like i still have to run rsd lite o_0, i'm so confused lol
Dilphat said:
well this atrix 4g is my first android based phone. As far as modding, i came from the winmo scene. from a fuze to tilt 2 to this atrix. thanks for actually trying to look for a sbf, i was able to find one not on filesonic...
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
but just not sure if it is the appropriate one needed. also, while i was at work, i did try and see what i could find on pudding and found a thread in regards to it, but nothing too much in detail about it. except for a if you don't understand any of the top 3 reasons then do this lol.
Click to expand...
Click to collapse
Failed to boot 4
Just in case someone else get's this error.
I used this sbf. at&t signed 2.3.4 4.5.91
http://www.4shared.com/archive/viniGE9x/1FF-olympus-user-234-4591-1106.html
and RSD Lite v5.6
From there when phone got to the motorola screen and said
"Failed to boot 4"
"Starting RSD Mode"
ran RSD with the sbf, it went through it's thing and it worked. it did revert everything that was done when the phone was rooted, and there is no root.
BTW, thanks for the help live4nyy!
live4nyy said:
There's really no measurement of risk for using RSD lite. If used properly it should go without a hitch but there have been "rare" occurrences of things going wrong. If you can find the correct sbf(2.3.4-4.5.91 signed) and download the current RSD then you should be fine
Pudding is the unlocked bootloader.
Fastboot files is what is needed to give commands in fastboot mode. (eg. "fastboot.exe")
Click to expand...
Click to collapse
edit* got the phone rooted again. now my problem is, webtop is gone lol. any thoughts on how to reinstall it?
Weird, the SBF file should of had that included. How big(MB) was the SBF file?
Dilphat said:
edit* got the phone rooted again. now my problem is, webtop is gone lol. any thoughts on how to reinstall it?
Click to expand...
Click to collapse
after extracted it is 1.46gb
live4nyy said:
Weird, the SBF file should of had that included. How big(MB) was the SBF file?
Click to expand...
Click to collapse
That sounds about right. How are you trying to access webtop? Do you have a lapdock or are you trying to just plug it into a monitor with the HDMI cable?
Dilphat said:
after extracted it is 1.46gb
Click to expand...
Click to collapse
I just figured out what i did wrong, i didn't have my hd multimedia dock plugged in lol
live4nyy said:
That sounds about right. How are you trying to access webtop? Do you have a lapdock or are you trying to just plug it into a monitor with the HDMI cable?
Click to expand...
Click to collapse
Major "derpage"...
Glad you got it working.
Dilphat said:
I just figured out what i did wrong, i didn't have my hd multimedia dock plugged in lol
Click to expand...
Click to collapse
I know right, and yup...I'm glad I got it working as well. but yup, in case it happens to anyone else, i put up the link to the sbf. just in case lol.
Now this gives me time to read up into unlocking the bootloader and flashing roms
live4nyy said:
Major "derpage"...
Glad you got it working.
Click to expand...
Click to collapse
I somehow messed up my photon. It says failed to boot 2 starting RSD mode. I try to use RSD lite, and flash the sbf and it fails to re-enumration (sorry forgot how to spell it) But when I pull the battery and it boots back into rsd mode I tried to flash derpunlocker and it says failed to boot 0x2004 after it boots back up. I can't figure out what I am doing wrong. Any help would be appreciated. (Sorry if I sound dumb)
jokerofchaos said:
I somehow messed up my photon. It says failed to boot 2 starting RSD mode. I try to use RSD lite, and flash the sbf and it fails to re-enumration (sorry forgot how to spell it) But when I pull the battery and it boots back into rsd mode I tried to flash derpunlocker and it says failed to boot 0x2004 after it boots back up. I can't figure out what I am doing wrong. Any help would be appreciated. (Sorry if I sound dumb)
Click to expand...
Click to collapse
Is your photon unlocked? Does it show "unlocked" when you turn on your device? You might be able to flash the recovery if unlocked and then flash a rom
No it doesn't say unlocked. It gives me some weird thing when trying to unlock it.
Svf 116:1:2
and then something about sec_exception b655
I will try to take a picture of it somehow to show or get the exact error it is giving me. Because it won't do anything but give me errors in rsd lite.
Sounds like you flashed the electrify bootloader unlock. Double check the file you flashed when you started getting this error.
Sent from my MB855
devastatorx said:
Sounds like you flashed the electrify bootloader unlock. Double check the file you flashed when you started getting this error.
Sent from my MB855
Click to expand...
Click to collapse
It is supposedly the one for the photon. I checked it again to make sure.
I tried it just a minute ago. I was using derpunlocker.sbf It gave me the error on my phone (i'd take a picture but I don't have a way) The error it is giving me is
SVF: 106:1:2
sec_exception: b655, eddc, eb
On rsd lite it says phone did not re-enumerate after RAM downloader was sent. (0x703E)
Go get 4.5.1A-1_SUN-198_7. Go back to Stock!!!
dsims7_2000 said:
Go get 4.5.1A-1_SUN-198_7. Go back to Stock!!!
Click to expand...
Click to collapse
I've tried that before and it gives me the same error, but I will try one more time.
OK, take a deep breath!!!
I'm uploading zip file you need. Not to insult you, take it, unzip it where you know where it is. (f**k, file too big, get if from Shabby!)
1. (Important) Make sure you charge your battery 100%
2. On PC, bring up RSDLite, upper left side, open that file. After you open it, it should come up in large box on upper right!
3. Holding down Voulme Down Button, power on phone, keep holding both down. You will see "Fastboot". release buttons. press volume down until you see "Android Recovery". Press the power button.
4. You will get triangle with "!" in the middle and little green android dude. Hook phone up to computer.
5. On Phone, Press Volume up and down at same time!
6. On computer in RSDLite, phone will come up in bottom box. click it. You shouldl see in on left next to box in step 2 above.
7. On phone, there is an option to initialize or something, do that. (cannot remember the exact words? sorry)
8. On Computer, upper right of RSDLite, click button to flash or install (again, I cannot remember exact words)
Go get a beer and come back in 30 minutes, all good. I actually came back every 5 minutes and shook the mouse so desktop did not go to sleep!)
Oh, I forgot, do not use USB on front of desktop, not enough power.
Trust me, it took Shabby, Joker, and Deedscreen 2 days to un-f**k me, I know the feeling of having a brick! anything else my e-mail is [email protected] and I got ya!
It gave me an error again. Should i use a desktop instead of a laptop? And does it matter if I have a sd card in the phone?
jokerofchaos said:
It gave me an error again. Should i use a desktop instead of a laptop? And does it matter if I have a sd card in the phone?
Click to expand...
Click to collapse
I left my SD card, nothing on it anyway!
You might want to use Desktop. I was reading somewhere NOT to use USB on front of Desktop, use USB on back because they have more juice? You might have same issue with Laptop? Matter fact, I did have issues with laptop, but I think it was more security with job?
It gave me the same error as before on the desktop. My mom's step brother is going to take a look at it today and might fix it for me. If he does I will post any info on it that could help.
Did you do step 7 of my instructions BEFORE you tried to connect the phone? That, more or less, gets rid of EVERYTHING and prepares for flash. I cannot remember exactly what the wording is, but there are like 10 Options. All of them are blank except THAT one! you need to let that complete before going to RSDLite.
Also, remember, you need a good battery charge!
I was able to fix it by flashing it, but now it is motorola electrify. Appearently i flashed the 235pudding on accident, and thats what messed it up. I do have it working now, but it sucks cause the bootloader is locked and i don't have a custom recovery but for the most part i am happy to have the phone back lol
What if it is not letting you charge nor holding power and volume down just makes it go black screen?
From the edge of time and space.
Heavy Metal said:
What if it is not letting you charge nor holding power and volume down just makes it go black screen?
From the edge of time and space.
Click to expand...
Click to collapse
Is the battery dead?
Hello, I am new to this forum.
I will try to explain the best that I can about how I got into this situation.
I was previously running on ICS 4.0.4(don't really know if it is .211 or .214 or something.). I tried to root it using Matt's Droid Razr Utility 1.7. I didn't really know what to do and was stupid enough to follow the video in the help thread(which was for upgrading from GB rather than rooting an ICS). Then I panicked.
I used option 1, followed by option 9, followed by option 3, followed by option 2, and then all four in random orders. Later on, I realized that I had to recover from the .211 file in the sd card after option 1(failure on my part). However, now whenever I try to enter recovery, I get Invalid Flash Mode Boot failure, whereas a normal boot will give me Invalid Flash Mode Flash failure.
I tried to use ADB tools and it didn't work.
Then I tried Utility 1.81. My driver is the same as the one provided, and the cable is the one that came along with the charger and phone.
My phone carrier is Singtel.
Any way out of this? Thanks in advance.
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
misterx11 said:
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
Click to expand...
Click to collapse
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
rageofshadow said:
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
Click to expand...
Click to collapse
chip0 said:
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
Click to expand...
Click to collapse
Do yall have XT910 or XT912 i.e. GSM or CDMA...
circleofomega said:
Do yall have XT910 or XT912 i.e. GSM or CDMA...
Click to expand...
Click to collapse
Since the thread name is Droid razr i think it is xt912
Go fast boot (power off your phone[if you cant then push and hold vol down+vol up and power button the same time, when you see your display flashed quickly release all buttons and press them again and hold- you should get boot menu and then use vol down to get on AP fastboot and use vol up to select it]).
Then use rsd lite and FXZ files to get your phone running, no need for any kind of wipe after this. Wait until rsd lite says finished.
What fxz files do I use? I've tried like 3 different ones and they always fail
Sent from my DROID RAZR using xda app-developers app
Hello,
I've searched for help on this and can't seem to find any.
Problem: Motorola Razr is stuck on the red m logo, but I cannot boot into the boot menu to flash via RSD or anything. The logo is offset to the left a little and has a small 1-2 pixel high rainbow of colors across the bottom. When trying to boot into the menu with power and vol + & - it simply boots without a logo but still the small bar of colors.
Probable cause: Phone's screen wasn't turning on and the phone wouldn't turn off so I did the reset with vol up and power while the phone was still probably on. Before when my phone's button wasn't responsive i used that to reset it and it had worked.
Info on phone and rom:
Rom - Rage rom 2.2 upgraded from 2.1 (worked for the past two months fine)
Phones base version: 98.72.16 (the april JB release) flashed via droid razr utility
Safestrap version 3.11
What I've tried: was going to try rsd flashing but i can't reach the boot menu.
Basic summary: Stuck on M logo and can't get into boot menu or safestrap, after holding vol up + power while phone was on.
Going into the boit manager and flashing via rsd lite both are different .
For flashing via rsd lite ya need to switch off ya mobile and then press both volume down and volume up at same time and press power button then.
It ll take ya into the bootloader and then using power down come till 3rd option ap fastboot and then press power up to select that now connect ya phone to pc and then flash the fastboot using rsd lite
Edit : make sure ya have installed appropriate drivers to get recognise ya phone by rsd lite
Thanks!!
Please hit the thanks button if i helped ya in anyways !!!
I think i have the same problem
I had MIUI on my Razr and today i wanted to try CyanogenMod, so i downlaoded it and installed it with ClockWorkMod, then rebooted and struck in the big red M, and no way to access the boot manger because if i press volume up + volume down + power it reboot, show the big red M then black sceen, and if it's conneced to my pc it tryes to install some drivers bit it fail, but still black screen
Is it bricked? What can i do?
morphalex90 said:
I think i have the same problem
I had MIUI on my Razr and today i wanted to try CyanogenMod, so i downlaoded it and installed it with ClockWorkMod, then rebooted and struck in the big red M, and no way to access the boot manger because if i press volume up + volume down + power it reboot, show the big red M then black sceen, and if it's conneced to my pc it tryes to install some drivers bit it fail, but still black screen
Is it bricked? What can i do?
Click to expand...
Click to collapse
Ya can't use boot manager and cwm recovery both . If ya want to use cwm ya need to remove all the files of bmm . Its just soft bricked not hard bricked so no need to worry just flash the appropriate fastboot file using rsd lite to get back to stock
Thats it
Edit : i think ya know the flashing method
Thanks!!
Please hit the thanks button if i helped ya in anyways !!!
anurag.dj2u said:
Ya can't use boot manager and cwm recovery both . If ya want to use cwm ya need to remove all the files of bmm . Its just soft bricked not hard bricked so no need to worry just flash the appropriate fastboot file using rsd lite to get back to stock
Thats it
Edit : i think ya know the flashing method
Thanks!!
Please hit the thanks button if i helped ya in anyways !!!
Click to expand...
Click to collapse
Thanks for trying but I tried following your instructions to get into fast boot and the screen just goes dark. Also when plugging into my PC it pops up on windows' end saying that a USB device has malfunctioned. I think I may just get it replaced under warranty unless sometime soon I find out theres a new way to fix it. But yeah it seems its too hard to tell if I'm actually in fastboot or if its even getting there properly.
Thanks!
As far as i know ya have tried all the unbrick method , none of them seemed to work . I believe ya razr is not soft or hard bricked and its not software problem too . Its hardware problem ya need to take it to service centre because it may be LED problem
Thanks!!
Please hit the thanks button if i helped ya in anyways !!!
How I fixed my Motorola Razr i (Intel)
Hello guys,
Since my Motorola Razr i phone is a company phone where I receive my corporate emails, I wasn't allowed to root the phone whatsoever.
My phone got stuck on the Red Motorola logo under normal usage. One day I turned it off and when I turned it back on, I had this problem.
How I solved it:
1) Downloaded and installed RSD Lite 6.1.4 which worked on Windows 8.1. Ensure all drivers are installed and that nothing is undetected in Device Manager. #important
2) I am based in Germany and I had the Vodafone Retail (EU) version. So I downloaded "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip" from http://sbf.droid-developers.org/phone.php?device=13. This corresponds to Android 4.1.2 Retail Europe.
3) I booted the phone in Fastboot (Power + Vol down; after restart and little vibrate, release power, keep finger on Vol down.)
4) The phone was detected in RSD Lite. I chose the zip file, unpacked and flashed.
5) Done. Phone was fresh. No warranty was void, nothing was rooted. All good.
Hope that helps somebody out there!
Cheers,
Shailen.
I've got the same issue. Took the OTA (was on stock OTA, rooted). Not, nothing but moto-logo with the only working option being AP Fastboot. Tried script utility to bring back to 4.1.2, but it fails on writing system and boot (preflash validation failed FAILED (remote failure)).
Is there another way to get the stock images flashed on there?
---------- Post added at 10:09 PM ---------- Previous post was at 09:36 PM ----------
crazifuzzy said:
I've got the same issue. Took the OTA (was on stock OTA, rooted). Not, nothing but moto-logo with the only working option being AP Fastboot. Tried script utility to bring back to 4.1.2, but it fails on writing system and boot (preflash validation failed FAILED (remote failure)).
Is there another way to get the stock images flashed on there?
Click to expand...
Click to collapse
Well, with RSDLite 6.1.6 and the most recent build from droid-developers . org I'm back in operation. Old version, wiped out, but at least I can make/receive phone calls.
How I got my Razr HD (XT925) Working! Flashed It WITHOUT LOSE ANY FILES!
I know this is a old thread, but if some one else falls here just like me, I had a problem with my XT925 too, and figured out that my only choice was to flash it up.
My phone was stuck in the red motorola logo, and it doesn't even tried to load the android.
After reading a lot of information and tried EVERYTHING, I fall here, and the comment of @shailentj saved my phone!
So I basically followed the steps that @shailentj posted in this very thread, with some differences.
1 - His link goes directly to Motorola RAZR i (XT890), but if you access ' sbf.droid-developers.org ' (I can't post links yet) you will be able to find your own model, which in my case was Razr HD (XT925).
2 - Extracted the whole firmware package (.zip file) and edited the .xml file, removing the "getvar" line. If you don't know what or how to do this, is just remove the line where you find the text "getvar". If you have trouble, just google it, there is a lot of information.
And finally, the reason I'm here. I found a way to don't delete USER DATA! My phone stuck, and I did't have any backup of my contacts (that is a lot of numbers) nor my files (photos, movies).
So I start to read the .xml file, and find a step "userdata", with operation "erase". This line says to erase the user's data partition, and in most cases, we don't want that.
Then, just remove the line in the xml written: " <step operation="erase" partition="userdata"/> ", and your files (may) not be erased!
4 - I start to flash, and then I got the infamous message "sistem_signature" failed. The solution was just download the last RSD I found (which in my case was 6.1.6).
5 - My phone restarts, with everything working great, system restored and ALL MY FILES AND CONTACT NUMBERS were there!
So very thank you @shailentj, your post really helped me a lot!
And yeah, you can flash your phone without lose any contacts or photos!
Now go, and spread the word!
pls i need a direct link to download the fastboot files for my droid razr xt912 verizon
my phone is brick and need to restore
da_proman said:
pls i need a direct link to download the fastboot files for my droid razr xt912 verizon
my phone is brick and need to restore
Click to expand...
Click to collapse
http://sbf.droid-developers.org/phone.php?device=9
Sent from my Razr XT910
I need help. My Droid Razr M (XT907) has the red circle and M logo and frozen screen. Can not find anyone who will attempt to flash the phone, like in the method that vitox32 posted about. Like most I have alot of information that I do not want to loose. Can anyone help????
purdy64 said:
I need help. My Droid Razr M (XT907) has the red circle and M logo and frozen screen. Can not find anyone who will attempt to flash the phone, like in the method that vitox32 posted about. Like most I have alot of information that I do not want to loose. Can anyone help????
Click to expand...
Click to collapse
try the correct forum
http://forum.xda-developers.com/droid-razr-m/help/qa-question-noob-friendly-t3142939
Sent from my XT1254 using XDA Labs