Ok...I'm at a point where I had no other choice but to get another replacement. I looked just about everywhere my patience would take me, and decided to give up. I hope someone could/would have a solution for me or others like me.
I had EH03 deoxed rom and decided I wanted ICS build5. So I installed CM7, I whiped cache, DLVK, and system data. Then flashed ICSb5 and GAPPS, Rebooted and stuck on ICS splash screen.
At this point USB ports wouldn't recognize fascinate. Downloaded all Fascinate drivers from Samsung, drivers for Nexus S, ADB, Android SK. You name it I got it. Nothing worked for USB detection. I even followed YT videos on turning Vista/PC off and unplug. Nothing.
After messing with data cords,(numerous ones,trying another PC), PC ports, I happened to pull plug and battery out of Fascinate at the same time, not sure what version of CWM, it was blue, came on. Luckily I had two Nandroid backups on SD.
I flashed Nandroid back to CM7 successfully. Rebooted fine and hooked to USB but still not recognized. At this point I was able to get into recovery using ROM. So, I did something stupid...lol...I tried to flash earliest Nandroid which was performed when on EH03 deoxed. Once I did this, I wiped all needed data and rebooted. Now Fascinate shows Samsung logo. It doesnt reboot, just that the logo stays until I pull battery. Now if I have battery in wth phone off and plug in, the charging battery comes on but doesn't show battery level. Doesn't go away till I pull battery.
The funny thing is that I can get into Download mode but USB is still unrecognized/malfunction on PC/Vista. I only wish that I was able to link phone and PC just to use Odin with PIT file and stock EDO5 or EH03.
Any advice?
dssheeley1 said:
Ok...I'm at a point where I had no other choice but to get another replacement. I looked just about everywhere my patience would take me, and decided to give up. I hope someone could/would have a solution for me or others like me.
I had EH03 deoxed rom and decided I wanted ICS build5. So I installed CM7, I whiped cache, DLVK, and system data. Then flashed ICSb5 and GAPPS, Rebooted and stuck on ICS splash screen.
At this point USB ports wouldn't recognize fascinate. Downloaded all Fascinate drivers from Samsung, drivers for Nexus S, ADB, Android SK. You name it I got it. Nothing worked for USB detection. I even followed YT videos on turning Vista/PC off and unplug. Nothing.
After messing with data cords,(numerous ones,trying another PC), PC ports, I happened to pull plug and battery out of Fascinate at the same time, not sure what version of CWM, it was blue, came on. Luckily I had two Nandroid backups on SD.
I flashed Nandroid back to CM7 successfully. Rebooted fine and hooked to USB but still not recognized. At this point I was able to get into recovery using ROM. So, I did something stupid...lol...I tried to flash earliest Nandroid which was performed when on EH03 deoxed. Once I did this, I wiped all needed data and rebooted. Now Fascinate shows Samsung logo. It doesnt reboot, just that the logo stays until I pull battery. Now if I have battery in wth phone off and plug in, the charging battery comes on but doesn't show battery level. Doesn't go away till I pull battery.
The funny thing is that I can get into Download mode but USB is still unrecognized/malfunction on PC/Vista. I only wish that I was able to link phone and PC just to use Odin with PIT file and stock EDO5 or EH03.
Any advice?
Click to expand...
Click to collapse
In the op of ics and also droidstyles guide you have to flash build 1 before you can flash build 5
Sent from my SCH-I500 using XDA App
I've never flashed version 1 before flashing.build 5. In fact I've had the least amount of problems going back to stock (ED05) then flashing ICS.
I bootlooped when i went from stock EH03 to Build 5 so i did 3 first then 5.
But this doesn't help our poster here.
OP:
you get into DL mode but odin wont see your phone?
What i suggest is to try: Move the usb cable to a different port. see if your pc can see it then. Second thing try a totally different computer. Chances are your PC is trying to use borked up drivers.
Once you get odin going flash a stock image [i recommend eh03] then cwm then build 3 and now the new build 6. good luck!
if you need any links or a more detailed guide I STRONGLY suggest Droidstyles guild, it is by far the best and most up to date for the fassy!
OhioYJ said:
I've never flashed version 1 before flashing.build 5. In fact I've had the least amount of problems going back to stock (ED05) then flashing ICS.
Click to expand...
Click to collapse
Consider yourself lucky....going from stock to build 6 causes me problems and many others. Going from stock, to build 1, then build 6 works flawless.
MOD please close thread due to lapsed timeline and no longer support of this model.Ty
Sent from my SGH-i717/GT-N7005 w/phMOD_beta2
dssheeley1 said:
MOD please close thread due to lapsed timeline and no longer support of this model.Ty
Sent from my SGH-i717/GT-N7005 w/phMOD_beta2
Click to expand...
Click to collapse
You realised you just bring a a old thread back yourself and no longer support of this model wtf you realise people.still use this phone everyday Right?
Sent from my SCH-I500 using Tapatalk 2
Related
okay i'll preface this by saying i read all the way through the Vibrick thread and any others i could find on this subject.
i was running NeroV3, decided to try CM7. made a dumb move (apparently?) by restoring back to my stock 2.2 backup via CWM, then flashing to CM7 and THEN trying to flash the Overstock kernel (these steps should be reversed?). i wiped the cache and dalvik cache, but then the kernel flash failed ("installation aborted"), so i rebooted, which went fine. i used ROM Manager to get back to recovery, tried flashing the kernel again, failed again, hit reboot, and then my phone got stuck on the Vibrant screen.
I tried every 3-button combo (also with battery pulls) to get to Download mode but nothing works. when i plug in the USB the spinny-working-hourglass thing pops up but freezes, the green charging bar does not come up, and it does not go to download mode.
when not plugged in, it just keeps returning to the Vibrant screen. i can't even get it to turn off without pulling the battery. i'm definitely not comfortable trying the solder method.
any help is appreciated - i'm not giving it long til i take it to t-mobile and play dumb, worst comes to worst i'll just get a cheapo replacement from the store and find another vibrant (or similar) used on craigslist.
thanks!
UPDATE:::
got the phone into download mode thanks to a thread by Dolphinwigs. had to do have odin open when replacing the battery/holding volume up/down.
waiting on the stock rom download now (internet is slow). hopefully all goes well from here...
The biggest issue I find is that people give up on ODIN to easily. Getting into download mode is not that hard but also not that easy eiither. This is why everyone should purchase a jig, never give up on ODIN try it a thousand times and then once more. Always have ODIN up and ready with the proper files on hand, and as soon as it connects to ODIN be ready to make shyt happen.
In your case an ODIN flash should get you where you need to be and after you root again flashing to CM7 should not be an issue. Keep in mind if you use the .tar in ODIN as well as the .pit you will lose everything on both internal/exteral SD. At this point unless you made a backup prior to your issue its really a lost cost.
Good luck!
i am now back up and running, i just didn't realize i needed Odin running when i tried to go to download mode. so simple, but so frustrating.
one thing though, the ROM i got is Eclair. do i need to update to FroYo before flashing CM7?
and also, so i do it right this time, do i flash the Overstock kernel BEFORE i flash CM7? or does it matter?
This is what happens when you have too much info with waaaay too little experience.
Bought an unlocked Vibrant from Amazon a year ago after the original tmobile one got stolen. It had issues like freezing up, tons of apps running all of time, etc. I finally tried installing froyo and it made the phone SO MUCH BETTER! Everything ran 1000% faster. I should have stopped there. But, it was pretty addictive I started reading about the new ice cream roms and somewhere, before I even got into it, I messed up the internal sd card. I have been working on this for a week, reading, downloading, flashing, etc. I feel like I have tried everything and have gone around in circles.
I can get into download mode with no problem. The furthest I have gotten after that was getting the "pass" in Odin. The phone does the boot up, then stay on the Galaxy S screen. Now, my computer won't recognize the phone (which has already happened) but now I am soooo confused and frustrated about where to go next. I have used AIO toolbox, Eugene's no brick, installing new drivers, new usb cord, etc.
Sorry so long. Thanks again.
bump...hope someone can help.
Could you give a clearer explanation/timeline of what you did? How did you mess internal sd?
Did you Odin stock jfd?
Sent from my GT-I9000 using XDA App
nolamom said:
bump...hope someone can help.
Click to expand...
Click to collapse
Is Clockworkmod recovery installed? If not, google: Samsung_Vibrant:_Full_Update_Guide and go to the Cyanogenmod wiki entry. Read through the "Installing Clockworkmod recovery" section.
In addition, from Addictivetips, to start recovery mode using the hardware buttons:
"Using hardware button combination on most Android devices:
On most Android devices including ones by HTC, you can enter recovery by powering your device off and then powering it back on while keeping either the ‘Volume Down’ or the ‘Volume-Up’ button pressed, depending on the device. This will enter the bootloader from where you can select the ‘RECOVERY’ option by navigating to it with the Volume key and entering it with the ‘Power’ key.
Sorry, but I'm not allowed to post links yet.
On most Samsung devices specifically Samsung Galaxy S series devices, you must keep both the ‘Volume-Up’ and ‘Home’ keys pressed while powering on the device, to directly enter recovery."
Thanks so much for the help. Ascallop: I tried to run Heimdall suite 1.3.1. The first time the drivers installed but I could not get passed the "run as administrator" on the next step. I have Windows XP professional even though I am on a home computer. It is automatically checked off to do so. When I tried again later that day, my computer again only recognized the vibrant as an unknown device. I just followed your link to Cyanogenmod's wiki and downloaded the older version and the same thing happened with the unknown device. I can't get passed that. Trailblazerz11, I think when I got to clockwork mod recovery, I hit repartition (if I am explaining that right). I was able to get into download mode and use Odin to get to the bootloader loop. I can't get into recovery. I was getting the message about the internal sd error. Now, I am stuck with the unknown device issue. I have tried a couple of different versions of Odin, the AIO toolbox, different usb ports, a new samsung cord, etc. Thanks again for helping this noob.
update: Used heimdall frontloader and installed cmenard overstock. Now I am stuck at the overstock screen. I am searching through different posts to find out more. But if you have any advice or can point me in the right direction, I'd appreciate it. Thanks again.
Have you tried repartition on odin?
sent from the xda app on my android smartphone.
Do you have an external SD card installed? If so, then remove it during the entire recovery process. I had lots of trouble recovering and flashing new kernels/roms while it was installed. Probably should have mentioned this earlier... sry.
No. It was already taken out. I am having trouble still with the vibrant not being recognized. I used the zadig, it recognized the samsung, did the next step, frozen at overstock screen. Now, after unplugging cable, Vibrant pops up as unknown device. Can't do zadig again.
I'm travelling until Friday, when I get back to my home PC, I'll odin my Vibrant back to stock Eclair and will list the steps that I took some months ago to install CWM/CM7. I once was at the same point as you are now, I just can't remember the steps verbatim regarding the recovery process. One question though: have you updated your phone via Kies at any point? If so, was the last update to Froyo?
BTW, I'm currently running (quite happily) ICS Passion V12 on my T-Mobile Vibrant.
The Vibrant is a pretty hard device to truly brick. Don't worry too much, yet.
Thanks so much ascallop! I think I tried Kies when froyo was offered as an update through Samsung. But, it wouldn't work. I thought it was because my phone came unlocked so I came here and was able to update to froyo and I loved it. I haven't used Kies since. The ICS Passion looks awesome. I think the ease of using froyo made me ridiculously overconfident. As of right now, I have gotten the drivers to download in Heimdall and used the frontend to flash the kernel. I'm not sure what to do next because it seems that if I reboot to get into download or unplug the usb, the computer won't recognize the phone again. I'm sure I'll be happily running ICS when you get back on Friday. Kidding, kidding.
nolamom said:
Thanks so much ascallop! I think I tried Kies when froyo was offered as an update through Samsung. But, it wouldn't work. I thought it was because my phone came unlocked so I came here and was able to update to froyo and I loved it. I haven't used Kies since. The ICS Passion looks awesome. I think the ease of using froyo made me ridiculously overconfident. As of right now, I have gotten the drivers to download in Heimdall and used the frontend to flash the kernel. I'm not sure what to do next because it seems that if I reboot to get into download or unplug the usb, the computer won't recognize the phone again. I'm sure I'll be happily running ICS when you get back on Friday. Kidding, kidding.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=13132341#post13132341
Let's get your phone back to Stock first. I just did this to my own Vibrant
I am officially back to stock!!! Thanks so, so much. After all of the reading and researching, you actually jumpstarted my recovery! Thanks again!!!
You're welcome
BTW, I flashed ICS V12r1 with Nelson's new kernel today. I love it. GPS works great for me, although others have reported problems. Same old deep sleep issue for them.
I wonder if flashing back to stock first is the key to fixing the prob. Don't really know though...
After the stock flash, the steps I took were:
copied kernel and rom to the internal sd card
One-click rooted the phone
odin (1.3) the Overstock kernel just to get cwm installed (instructions on the cm7 wiki)
reboot to cwm
wipe data/factory reset
wipe cache/dalvik
flash rom
reboot, let settle
reboot to cwm
flash kernel (I used: ICS_Passion_sunset_with_nova)
reboot, let settle
---------- Post added at 05:29 PM ---------- Previous post was at 05:24 PM ----------
One more thing: I flashed the Gingerbread bootloader as well. After you do this the key combo for cwm is: Vol-up + power. Let go when you see the boot splash.
Sounds sweet! Although I'm back to stock, I can't root because I can't access the internal drive. A message comes up about E: no such file, etc. I can see the phone storage memory amount and the phone holds data. I don't have an external card in right now. So, here I go again....
You shouldn't need an external card to root. Try One click root:
http://forum.xda-developers.com/showthread.php?t=1125414
nolamom said:
Sounds sweet! Although I'm back to stock, I can't root because I can't access the internal drive. A message comes up about E: no such file, etc. I can see the phone storage memory amount and the phone holds data. I don't have an external card in right now. So, here I go again....
Click to expand...
Click to collapse
When I've seen that E: error, it has been because of a mismatch between the CWM version and the filesystem layout on the device. CWM for CM7 doesn't work for ICS, for example. At least not for me.
---------- Post added at 10:24 AM ---------- Previous post was at 10:22 AM ----------
cashmundy said:
When I've seen that E: error, it has been because of a mismatch between the CWM version and the filesystem layout on the device. CWM for CM7 doesn't work for ICS, for example. At least not for me.
Click to expand...
Click to collapse
And of course the stock recovery won't work with anything else. Different partitioning, different filesystems.
Okay. I was able to root with the one click root app. Now, I need to figure out what to do next. Ascallop, I was reading about your latest updates. I have to go through it a few times so that I can understand it all. I had froyo before and it blew away stock. I can't imagine what ICS is like Thanks again for all of the help. I HATE being back to stock.
The only reason I'm not running ICS is that I'm waiting for CyanogenMod permissions management to appear in anyone ICS rom. I'm really tempted to try Passion. ICS is markedly better than the best GB in various ways. Just remember to take a nandroid backup before upgrading, and that if something doesn't work and you need to downgrade, you will have to get the downgrade done successfully before you can nandroid-restore. Good luck!
Thanks Cashmundy. I saw the video for the root and install ice cream sandwich by Eddie West (I think that is his name.) He is a dj also. It looks like everything I would need so I may go with that.
A friend just gave me a SGH-T959 Galaxy S Vibrant. It still has the stock 2.1 on it. I'd like to upgrade it to CM7 or maybe CM9, but all the instructions I've found say you should at least be on 2.2. I've been trying for several days to upgrade to 2.2 using Mini Kies. It downloads the rom (not sure where it stores it on my machine), reboots the phone in download mode and just sits. I left it for hours several times and nothing. If I reboot it it is fine when I reboot. It is just never copying anything to the device.
Is there a way to do the update without Mini Kies. I should also mention that my machine is a MacBook Pro running lion. I've tried this on a Windows XP VM in VMWare Fusion and I get the same exact results, it goes to download mode and then nothing.
xltrigger said:
A friend just gave me a SGH-T959 Galaxy S Vibrant. It still has the stock 2.1 on it. I'd like to upgrade it to CM7 or maybe CM9, but all the instructions I've found say you should at least be on 2.2. I've been trying for several days to upgrade to 2.2 using Mini Kies. It downloads the rom (not sure where it stores it on my machine), reboots the phone in download mode and just sits. I left it for hours several times and nothing. If I reboot it it is fine when I reboot. It is just never copying anything to the device.
Is there a way to do the update without Mini Kies. I should also mention that my machine is a MacBook Pro running lion. I've tried this on a Windows XP VM in VMWare Fusion and I get the same exact results, it goes to download mode and then nothing.
Click to expand...
Click to collapse
Whoops, mix up, JFD is 2.1 Eclair. You can still flash CM7 without 2.2, just follow this guide:
http://wiki.cyanogenmod.com/wiki/Samsung_Vibrant:_Full_Update_Guide
After flashing the kernel via heimdall, if it never boots, just wait a few minutes and pull the battery, then boot into recovery by VOL-UP + VOL-DOWN + Power, then continue.
Just flashed the zImage. I'm waiting for boot. The talking updates on time remaining are kewl. Thanks for you help. Hopefully all works well.
Is CM9 stable enough to run ok, or should I stick to CM7.2?
xltrigger said:
Is CM9 stable enough to run ok, or should I stick to CM7.2?
Click to expand...
Click to collapse
CM9's okay. I run it. But both CM7 and CM9 may still have intermittent issues with 911 calling. There are two people who can't call period (they _may_ have a corrupted /efs which would prevent them from calling even on stock now, but not sure). Some who failed and then worked, etc, etc.
Looks like I may have screwed myself. It won't boot after the zImage. I can boot CWM, but I can't do a USB mount in CWM. I can enter the menu, but it never shows up. If I had copied CM and GAPPS before the zImage I'd likely been ok. I tried putting the zip files on external MicroSD, but CWM offers me no way that I can see to apply a zip from that. It only sees the internal.
If you have any suggestions on where to go from here please let me know.
Update:
Even though I couldn't get into the device when booting normally, I was able to get connect using adb.
I did "adb push cm-9-20120707-NIGHTLY-vibrantmtd.zip /sdcard/" and was able to copy the update to my phone.
I did the same for gapps. So far so good. I'll update this post again when all is finished.
Update 2:
I've got CM9 installed and booted. Downloading my apps now. Thank you so much for your help /me is really happy now
If its your 1st time on ICS with the T959 I suggest reading this:
http://forum.xda-developers.com/showthread.php?t=1464423
Hello all,
I have a question that has not been answered after many hours of searching. Hopefully I'm just dumb, and my buddy's stock firmware and data isn't hosed. I'm trying to get his stock firmware running again so I can back it up safely.
What I've done:
Tried to flash CWM's update.zip via stock recovery (signature verification failed on the three different zip's I could find in the forums and various links)
Used Heimdall to push "cmenard-T959-CWM" zImage (this worked, and I get a different screen at boot)
The phone boots to the point of the T-Mobile splash screen with the annoying shriek sound, but goes to a black screen after. If i touch any of the soft buttons, they light up and remain lit. It'll stay like that for at least 20 minutes.
Is it possible to re-flash the system partition and not the data partitions using ODIN? Is that even feasible? Like I mentioned above, I'd like to get the stock firmware running such that I can make a good backup of it with all the user data intact. I haven't been able to because the CWM+root wouldn't flash.
Any suggestions or insight would be greatly appreciated.
thanks in advance!
Well as long as you don't format the internal SD, any pictures and videos and things should remain intact.
Here is a similar thread. See if it resembles your issue.
http://forum.xda-developers.com/archive/index.php/t-794869.html
Toast6977 said:
Well as long as you don't format the internal SD, any pictures and videos and things should remain intact.
Here is a similar thread. See if it resembles your issue.
http://forum.xda-developers.com/archive/index.php/t-794869.html
Click to expand...
Click to collapse
Thanks for the suggestion, Toast. I don't believe the internal SD has been messed with, and I don't plan to mess with it either. The thread you linked is not quite related to my issue, as far as I can tell.
I am able to get into Download Mode, and the Stock Recovery mode as well. However every time I try to flash an 'update.zip' with the Stock Recovery, I get an error about Signature Verification Failure.
After stepping back from it for a day, I think I've gained some clarity. Since all I've done is flash a different Kernel with Heimdall, I'm going to try to flash a stock kernel then see what happens.
Is this phone on stock Froyo or have you got it back to JFD (eclair)?
If Froyo, that's the problem. Using Odin back to Eclair and run update.zip. It won't work from stock Froyo.
*-*- I made some assumptions in my previous post. The shrieking sound. Black screen. Lights stay lit. Sounded like a poltergeist.
Glad you can get in download mode and recovery.
The old 2E vs 3E problem. Nice catch Toast
Give this a whirl: recovery 3e modified to work like recovery 2e
Might have to ABD push it to your internal SD card though.
Toast6977 said:
Is this phone on stock Froyo or have you got it back to JFD (eclair)?
If Froyo, that's the problem. Using Odin back to Eclair and run update.zip. It won't work from stock Froyo.
*-*- I made some assumptions in my previous post. The shrieking sound. Black screen. Lights stay lit. Sounded like a poltergeist.
Glad you can get in download mode and recovery.
Click to expand...
Click to collapse
Woodrube said:
The old 2E vs 3E problem. Nice catch Toast
Give this a whirl: recovery 3e modified to work like recovery 2e
Might have to ABD push it to your internal SD card though.
Click to expand...
Click to collapse
hahaha poltergeist!
Wow, so I'm glad I asked. I wouldn't have known about this issue, as I do not have any history with this device.
I know that the ROM is currently 2.2, and the Android System Recovery is showing "3e".
If I understand correctly, once I'm ready to flash up to ICS, I'll need to ODIN back to 2.1 to get Android System Recovery "2e", which will let me flash 'update.zip' packages freely. Then I flash an 'update.zip' to get CWM, then flash CM7, then CM9 (and CM9 is my intended destination).
The things mentioned in the thread you linked do appear to apply to my situation.
However I still want to get the stock OS booted and working, then do a Nandroid backup of it. (it's the computer tech/security pro in me. Since I'm new to this device, I -tried- to read up on everything first, and didn't want to make a change without being sure it would work.)
Does anyone happen to know if flashing a stock kernel over the 'cmenard' kernel will harm anything, and hopefully get a successful boot? Again, I'm trying to get the stock ROM booting again in order to verify I have everything I need off of it, then do a nandroid backup. Flashing to CM9 will come afterwards.
Ok, here are some things for you.
Here is a kernel pack that you can use. Read the OP because there are Froyo AND Gingerbread kernels in there.
[KERNELS] Moped_Ryder SGS Kernel Pack v2 [20+ Froyo/GB Kernels]
I really suggest using something like BaliX 1.2 or BaliUV kernels to make your back up. They are smooth, fast and OC/UV-able. To flash just Wipe /cache, /dalvik -> flash kernel -> Wipe /cache, /dalvik (I also fix permissions too bc that is the way that I learned and I just do it that way all the time). Reboot and Bam!! you should be able to get to the point that you can make a backup.
Look in my signature, there are downloads and flashables that are direct download linked. There is also an ICS install guide that can help your journey. Once you have your backup, then use Odin from the Toolbox in my signature and flash back to stock JFD. From there you will be able to follow my guide.
If you need any files, just let me know and I will upload them when I get home (won't be until late though, i have plans right after work).
Using HB, can I choose any theme? I am not so acquainted with the Theme chooser and boot animation of my phone. I flashed a boot animation zip yesterday and it was stuck in "ANDROID" screen. So I have to flash again. I never used any boot animation and themes in my phone yet. I want to know about them.
Sent from my SGH-T959 using xda app-developers app
Wrong thread. Put that question in the Jelly Bean Banter thread. No need to hijack this thread until we get OP up and running.
Ugh, so I've been on vacation for a while, and since being back I've been super freaking busy =(
Finally spent some time with the phone tonight. Took some fiddling to get the right drivers working for the phone on my Win7x64 laptop.
In any case, I checked out that Kernel thread, and extracted the Bali kernel. Since I had flashed successfully(?) with Heimdall at first, and I'm becoming more familiar with it, I used it to flash the Bali_1.8.8-zImage. That appeared to work, as I get a new boot screen/animation with the Bali logo.
However, after the Bali logo disappears, the T-Mobile animation+sound plays, and then gives me a black screen. The screen is on (backlight is on) but all black. Also, if I touch a soft-button, they'll light up and the phone will remain in that state for as long as I can stand to wait. (one episode of Archer)
So, it's doing the same thing as before, but with a new boot logo/animation.
I wonder if something else in the ROM has been messed up? Should I forget trying to save it, and just use ODIN to flash a whole new rom/kernel package? I'll talk to the owner tomorrow and see if he's now willing to do that.
I also wonder if I was wrong to use Heimdall again, instead of using the CWM method. Please correct me if I'm wrong, but I think those two methods end up doing the exact same thing. Is one method more reliable than the other?
Bah, this sucks; I have more questions than answers at this point =( Any ideas, Woodrube, Toast?
maxpeet said:
Ugh, so I've been on vacation for a while, and since being back I've been super freaking busy =(
Finally spent some time with the phone tonight. Took some fiddling to get the right drivers working for the phone on my Win7x64 laptop.
In any case, I checked out that Kernel thread, and extracted the Bali kernel. Since I had flashed successfully(?) with Heimdall at first, and I'm becoming more familiar with it, I used it to flash the Bali_1.8.8-zImage. That appeared to work, as I get a new boot screen/animation with the Bali logo.
However, after the Bali logo disappears, the T-Mobile animation+sound plays, and then gives me a black screen. The screen is on (backlight is on) but all black. Also, if I touch a soft-button, they'll light up and the phone will remain in that state for as long as I can stand to wait. (one episode of Archer)
So, it's doing the same thing as before, but with a new boot logo/animation.
I wonder if something else in the ROM has been messed up? Should I forget trying to save it, and just use ODIN to flash a whole new rom/kernel package? I'll talk to the owner tomorrow and see if he's now willing to do that.
I also wonder if I was wrong to use Heimdall again, instead of using the CWM method. Please correct me if I'm wrong, but I think those two methods end up doing the exact same thing. Is one method more reliable than the other?
Bah, this sucks; I have more questions than answers at this point =( Any ideas, Woodrube, Toast?
Click to expand...
Click to collapse
Wrong they are not the same. cwm can do the work without a PC beside you can erase, back up , restore and flash, which make our life easier, heimdall or Odin ," I prefer odin "are the last option when you can't fix it with cwm
To fix your phone use Odin or heimdall and go back to stock don't worry all your files, photo, music, will be safe. Then
1 get root on you , if you don't how ask
2 get cWm
3 do a nandroid back up
4 have fun flashing all roms you want lol
Sent from my SGH-T989 using xda app-developers app
Yeah, I would just Odin back to stock JFD w/ repartition checked...
Then I'd flash something real stable for him. There are lots of stable ROMs to choose from. I used Bionix V for a long time before moving onto Jelly Bean.
Since the phone belongs to someone else, I'd stick with something lower than JB though. 911 can have/has issues.
Toast6977 said:
Yeah, I would just Odin back to stock JFD w/ repartition checked...
Then I'd flash something real stable for him. There are lots of stable ROMs to choose from. I used Bionix V for a long time before moving onto Jelly Bean.
Since the phone belongs to someone else, I'd stick with something lower than JB though. 911 can have/has issues.
Click to expand...
Click to collapse
do no check de re-partition button and use a .pit file follow this tutorial and you will be fine
http://forum.xda-developers.com/showthread.php?t=848737
I've been running rooted with Alliance Rom build 32 for about a year with zero problems. The phone battery ran low last night and the phone turned off. When I turn it on it stops at the first logo. I can't get into Philz
recovery. It will go into downloader mode. I tried using Odin to revert to the stock MJ9 I started from when I used Casual. It flashed successfully (stock pit and MJ9) but still gets stuck at the the first logo and won't go into recovery.
SD card is removed. I haven't made any modifications to the phone for the past six months except adding a few well known apps from the store.
Any advice on how to get back to where I can load recovery and proceed to reinstall would be greatly appreciated.
PS.
I would have bought a new phone last year but it seems all the ones I like are bootloader locked. I can live without the stylus (would love a new note though...). Any recommendation on a replacement for the Note 2 would be much appreciated.
dsteinschneider said:
I've been running rooted with Alliance Rom build 32 for about a year with zero problems. The phone battery ran low last night and the phone turned off. When I turn it on it stops at the first logo. I can't get into Philz
recovery. It will go into downloader mode. I tried using Odin to revert to the stock MJ9 I started from when I used Casual. It flashed successfully (stock pit and MJ9) but still gets stuck at the the first logo and won't go into recovery.
SD card is removed. I haven't made any modifications to the phone for the past six months except adding a few well known apps from the store.
Any advice on how to get back to where I can load recovery and proceed to reinstall would be greatly appreciated.
PS.
I would have bought a new phone last year but it seems all the ones I like are bootloader locked. I can live without the stylus (would love a new note though...). Any recommendation on a replacement for the Note 2 would be much appreciated.
Click to expand...
Click to collapse
If you're looking for a newer phone that lets you unlock the bootloader, you might want to check out last year's Nexus 6 or the newer Moto X Pure Edition. The Nexus 6P from Huawei also looks nice and I'm keeping an eye on it as my next potential phone. The Nexus 5x from LG should also have a boo that can be unlocked.
-----------
Hopefully, you didn't flash the stock Verizon MJ9 4.3 firmware back onto your phone. If so, then you have locked your bootloader with no way to unlock it.
I'm thinking that you're probably getting confused with needing to flash Beanstown106’s modified MJ9 firmware (which doesn't return the phone to stock or contain the 4.3 bootloader). See one of my previous posts ( http://forum.xda-developers.com/showthread.php?p=58541771 ), which discusses a similar issue and has a link on how to flash the stock recovery back onto the phone if you'd like to try that rather than restoring the phone back to stock 4.1.2.
You could also just Odin restore the phone back to Verizon factory stock 4.1.2 and run Casual again to start fresh. See Droidstyle's restore guide here: ( http://forum.xda-developers.com/showthread.php?p=34891181 ) to get instructions on how to flash back to 4.1.2.
Once back on 4.1.2, you need to go into the stock recovery and wipe cache /factory reset to make sure everything is wiped off the device for a fresh start. (Odin doesn't wipe everything in it's flashing process).
If you restore back to stock 4.1.2, then be careful not to let your phone take an OTA because if it gets updated to 4.3+, then you won't be able to unlock the bootloader any longer.
I usually remove my Sim card when restoring to stock 4.1.2... just to ensure I don't accidentally take an OTA update before I get it rooted again. (You can skip the initial phone Setup screen with the method in this YouTube video - https://youtu.be/qekEpn1Bufc ). It says it's for the S3 but works on the Note II as well. Once you get back into the phone and enable USB debugging in Developer options, you should be able to run Casual again. The phone doesn't have to be activated or on wifi to do this.
Once Casual is successful, it's safe to put the Sim card back in because I don't believe an OTA can install successfully with a custom recovery installed.
Good luck.
mattnmag said:
I
Hopefully, you didn't flash the stock Verizon MJ9 4.3 firmware back onto your phone. If so, then you have locked your bootloader with no way to unlock it.
Click to expand...
Click to collapse
All the ROM's and tools are from threads here so pretty sure I'm using Bean's modified MJ9. I was on Beans 4.3 for over a year before I went to the Alliance ROM.
You could also just Odin restore the phone back to Verizon factory stock 4.1.2 and run Casual again to start fresh. See Droidstyle's restore guide here: ( http://forum.xda-developers.com/showthread.php?p=34891181 ) to get instructions on how to flash back to 4.1.2.
Once back on 4.1.2, you need to go into the stock recovery and wipe cache /factory reset to make sure everything is wiped off the device for a fresh start. (Odin doesn't wipe everything in it's flashing process).
If you restore back to stock 4.1.2, then be careful not to let your phone take an OTA because if it gets updated to 4.3+, then you won't be able to unlock the bootloader any longer.
Click to expand...
Click to collapse
4.1.2 sounds like a better idea - I have that also.
Thanks your advice here is just what I was looking for in my effort to get this phone running again.
Update: I can still go into Download mode but cannot get a computer to recognize the phone now.
Not one of three computers, numerous cables including one out of the Galaxy Note 2 box and all the tricks I could find like pulling the battery while connected helped.
The first day of this problem (stuck at first logo) I was able to connect to the phone with Odin. I flashed the following:
1. sch-i605-16gb.pit
2. CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar
Would something like http://forum.xda-developers.com/galaxy-s2/help/guide-how-to-make-usb-jig-reset-binary-t1604707 help?
Should I look into the JTag guys on ebay?
Thanks,
dsteinschneider said:
Update: I can still go into Download mode but cannot get a computer to recognize the phone now.
Not one of three computers, numerous cables including one out of the Galaxy Note 2 box and all the tricks I could find like pulling the battery while connected helped.
The first day of this problem (stuck at first logo) I was able to connect to the phone with Odin. I flashed the following:
1. sch-i605-16gb.pit
2. CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar
Would something like http://forum.xda-developers.com/galaxy-s2/help/guide-how-to-make-usb-jig-reset-binary-t1604707 help?
Should I look into the JTag guys on ebay?
Thanks,
Click to expand...
Click to collapse
I don't know if a USB jig would help the computer recognize the phone again.
Since you tried 3 different computers and still couldn't get it recognized... I'm wondering if something got fubared when you Odin flashed the VRLJB stock Rom. So when you go to Device Manager in the computer, the computer doesn't even show anything connected at all?
I don't know that it would be worth the time, but (on the computer that last worked for your phone), you could try uninstalling the Samsung Drivers, and then use a program like DevManView to totally uninstall all Android related drivers. Restart the computer afterwards and then reinstall the Samsung USB Drivers (from here: http://www.samsung.com/us/support/owners/product/SCH-I605) . Then connect your phone back to the computer in Download Mode to see if it will reinstall the drivers and recognize it.
If the computer still doesn't recognize the phone after all that, then I'm out of ideas.
I'll try the devmanview driver cleanup (love nirsoft utils!) and install the driver in your link on the orginal pc which I use for flashing ROMs. If that doesn't work I'm going to look into sending it out to a JTag guy although they claim if you can get into download mode after they perform their magic that they were successful.
Went with the LG G4 which I'm very happy with. As far as getting the Note 2 running again I've been thinking l might buy a used Verizon Galaxy Note 2 motherboard on ebay rather than sinking a lot of time into trying to... should I say "unbrick" it.
If you ran casual first, it will not connect to the samsung driver, until you uninstall the USB services from the device manager, and then run find new hardware.
But maybe this will not help considering you already tried 3 machines?
I may have had the Samsung driver on all 3 machines. Good suggestion - I'll post back if it works.
Related question. I see you are running CM 12.1 - do you have standby battery drain issues? My 4.4.2 Alliance 32 would drain the battery down to 0 if I didn't plug it in at night even though I might still have 1/3 charge.
dsteinschneider said:
I may have had the Samsung driver on all 3 machines. Good suggestion - I'll post back if it works.
Related question. I see you are running CM 12.1 - do you have standby battery drain issues? My 4.4.2 Alliance 32 would drain the battery down to 0 if I didn't plug it in at night even though I might still have 1/3 charge.
Click to expand...
Click to collapse
Right, it was in the Adam Antler video, for casual. Once you use the casual on USB, the samsung driver will not work until you uninstall and reinstall USB system.
I can get almost 3 days out of a phone battery with little or no use. The one I am using could make it a day and 1/2, but I charge that one every night because I do not need and down time just in case.
I am using the nightly build, 12.1-20151222 12/22/15, I am not sure how the other builds are, or even the stable build for that matter?