My friend brought by his Galaxy Tab 10.1 over for me to fix and another of his friends had loaded a custom ROM on it and it was stuck in an endless boot cycle. I got into the CWM recover menu to factory reset and wipe all cache folders used ADB to push Android Open Kang Project - p4wifi (build 21) followed instructions to a T... Rebooted and started the first time setup of ICS and it froze and rebooted just like the other ROM before. I re-flashed the ROM with out Gapps and factory reset. Rebooted and it got to the home screen and froze again after about 30 seconds. I turned it off (by holding the power button down). Now when I try to turn it on it does nothing. Hold power and vol - it does nothing. Plugged it into the wall to charge it does nothing. Power and vol + does nothing a well. Plugged it to my PC the drivers are no longer found... Tried everything the only signs of life are the fact that when its plugged to the PC the drivers don't install (listed as APX under other devices) and power + vol + makes a 3 beep tone on my windows idk what that means...
Related
Good Day,
I have an Archos70IT that i had not used in a while, It was working OK, I went ahead and reset everything to factory and it booted OK, I installed applings and Gapps and still worked OK then suddenly it froze, I used the power button to reset and after that I get a boot loop with the Archos Entertainment your way splashscreen and then after a couple of seconds blank screen and almost immediately the same splashscreen.
This is what I have tried/found out so far:
- Tried to boot the recovery console by resetting (Hold Power for 10 sec), waited a minute, tried to boot with Power and Volume Down (-) pressed and I only get a static splashscreen and it stays like that until I reset again.
- Let the battery die by leaving the splashscreen bootloop all night, connected to power and after a couple of days tried again with the same result.
- Have tried resetting and connecting to USB nothing detected by the computer, at this step have tried resetting, holding power + volume up and down and no luck, same result.
So I have no idea on what else to do, I think I screwed up by not updating the firmware before installing apps after the whole factory reset.
So thanks to Netflix and its implementation of security net I wanted to install Magisk on my Z2.
Im running the stock 6.0 Rom which was just rooted with supersu.
My tab was charged 80+%
I uninstalled SuperSU, went to TWRP and flashed Magisk.
After flashing the screen stayed black. Nothing at all.
Long press power gives me one vibration after 3 seconds but nothing else.
Long press power & vol - gives me the same vibration
Long press power & vol + gives me nothing
Connecting the tab to the computer gives me nothing. No device recognised (no adb, no fastboot)
Connecting the tab to a charger has the LED blinking red.
Long pressing power makes the led turn solid (no blinking)
Power & vol - the same
Power & vol + nothing
Basically I seemed to somehow have turned my tab into a brick oO
I can't even get it to boot to twrp or fastboot
Atm I'm letting it charge just to see if that was an issue (I doubt it)
Otherwise the only thing I can think of is opening it and disconnecting the battery...maybe that will help?
Ok nevermind. I managed to get into flashmode and reflash. tab is now working again!
How did you get it to be recognized and reflash? I flashed mine after rooting and I get similar behavior to what you were getting. It will vibrate once if I press the power button, I can get it to turn the light blue if I hold the up volume and the power button while plugged in. The screen will not turn on at the Emma tool doesn't seem to recognize it.
Same Problem here.
@pseudoheld could you please provide some more info?
I have installed Crdroid Nougat ROM to my LG G2 D802 yesterday, everything was fine. After flashing something via recovery phone went dark. When I boot device it shows only LG logo with secure booting error, then the screen goes black while phone is still on. Download mode and recovery wasn't working. When I plug to usb computer was going crazy with device errors. I tried a lot of solutions like this , with ubuntu and windows 10. Nothing worked for me. After a few hours I found a simple solution in a forum. Worked for me, maybe work for others..
Press Power and Vol Down buttons together for about 10 seconds, When you see LG logo release for a half of second and immediately press and HOLD again Vol Down + Vol Up button. Factory reset screen will come. Select yes with vol down button and press power button to factory reset.
themaster33 said:
I have installed Crdroid Nougat ROM to my LG G2 D802 yesterday, everything was fine. After flashing something via recovery phone went dark. When I boot device it shows only LG logo with secure booting error, then the screen goes black while phone is still on. Download mode and recovery wasn't working. When I plug to usb computer was going crazy with device errors. I tried a lot of solutions like this , with ubuntu and windows 10. Nothing worked for me. After a few hours I found a simple solution in a forum. Worked for me, maybe work for others..
Press Power and Vol Down buttons together for about 10 seconds, When you see LG logo release for a half of second and immediately press and HOLD again Vol Down + Vol Up button. Factory reset screen will come. Select yes with vol down button and press power button to factory reset.
Click to expand...
Click to collapse
This worked beautifully after a few tries to get the timing right! Thank you!!
Hello. I have a SM-G925F which i rooted and then installed TWRP recovery by following youtube and tutorials here. Everything works fine for an hour and then the phone suddenly stop responding with a frozen screen. I tried to reset it by holding Power and Vol -. It turned off just fine however, it did not respond after attempting to turn it on. I have a feeling that i somehow messed up my firmware or whatever during twrp installation.
Notes:
1. No response when charging
2. Not powering on
3. Nothing happens when i pressed V up + power, Vol down + power... etc.
4. Does not respond to USB Jig.
Hope someone could help me out.
Hello,
as I wrote in this (now locked) thread, I installed Superior OS and got stuck in bootloop. I get "Galaxy S9+" screen followed by system bootanimation, which repeats itself indefinitely. It doesn't restart by itself, it just boots endlessly.
The problem here is that I can't access recovery or even download mode. I tried to restart (power + volume down) and then quickly press combination to access recovery or download mode. No luck. I couldn't even turn the damn phone off. I just kept restarting.
So I let it drain the battery hoping I could then power the phone on with correct key combination. I tried holding bixby button + volume down while inserting USB. It just started booting up to system with boot animation. I tried holding bixby + volume up, or even power + bixby + volume down. No luck either.
I got correct USB drivers installed, as I flashed the phone with Odin in the past. Odin recognizes phone while it sits on boot animation, but it won't start flashing. ADB or fastboot do not work on bootanimation, as the ROM is freshly installed. I presume it has ADB turned off by default...
I'll be grateful for any ideas and suggestions.
No escape , man. I tried all ( check this rom for galaxy note 9 )
Nice...
I went to service center, they said they can fix it for me. 40 euros for reflash (download mode isn't necessary), 100 euros for complete unbrick. I hope the unbrick isn't necessary and the bootloader is intact. I'll post with update.