Related
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
So I managed to shatter the glass on my rezound....go me. I was wondering if anybody here has replaced the screen on the rezound and how hard it is to do. I didn't find a lot of rezound tear down info out there. I do a lot of laptop work and it seems like simular construction techniques. the only thing that has me a bit concerned is the whole adhesive issue. Using a heat gun to get the old screen off and I guess the new one will either adhere to the old adhesive or I need to find a source??
Anyway they appear to be 50 dollars for the part versus 100-150 to send the phone off to have someone else do it. Any thoughts???
While I haven't done the rezound yet, I have done a few others, the most recent being a Droid X. I ordered the 'official' advesive on the first phone screen repair I did but never again. It was hard to deal with...if you don't get it right perfectly the first time... you're done. I went with a 3M double sided foam tape after that and was SO much easir to deal with. Never had a screen pop off and anything like that. My wife is still using that phone as we speak.
Next biggest thing to watch out for is tearing those damn thin cables.... they tear so easy...seriously, do not use any sort of tension on those cables. One little tear could out your camera, or soft keys... or even portions of your digitizer. Such a pain in the ass.
Take care while dis & re assemb ling it, you should be fine. It's a lot more delicate than a laptop, so be careful.
I have never replaced the screen on my Rezound, but I have done a few other phones. My wife dropped her Dinc and broke the screen, then the digitizer went out on my OG DROID. If the Rezound is built like the Dinc then you will be golden. Took only about 20 minutes. But as stated above you MUST be very careful when disassembling the phone. The micro ribbons are a little forgiving but are pretty delicate.
Good luck though and let us know how it works out for you.
Sent from my ADR6425LVW using xda premium
Well I opted to get it replaced mainly because I found a local place that could do it and had the part in stock. However the one they installed has clear buttons instead of red, which I like more but I think its best to stay with the way it is suppose to look. Also there is a small black line that they think might be a smug. They are looking for a screen with the factory red buttons. The question I have is I noticed this digitizer registers 4 points and I thought the rezound did 5 can someone verify how many points of touch its suppose to recognize?
kappen said:
Well I opted to get it replaced mainly because I found a local place that could do it and had the part in stock. However the one they installed has clear buttons instead of red, which I like more but I think its best to stay with the way it is suppose to look. Also there is a small black line that they think might be a smug. They are looking for a screen with the factory red buttons. The question I have is I noticed this digitizer registers 4 points and I thought the rezound did 5 can someone verify how many points of touch its suppose to recognize?
Click to expand...
Click to collapse
My rezound i got from verizon refurb only has 4 input.
my rezound has always only had 4 points
Thanks for the replies.
Hi everybody. So, I've had my S3 since April.. it was a birthday gift. I love it and baby it as if it were my own child.. yesterday I had taken my Otter Box Commuter case off to take out my battery because my phone had restarted itself, but had been stuck in some odd boot loop. So wah lah, took the battery out and put it back in and Bob's your uncle it fired right up. Normal.. now I've only dropped it twice in the past three months I've had it and well, nothing had happened to it, except for some minor scuffs on the back casing.. yesterday, being the second time I've dropped it, hit the concrete pretty bad but on the back side only.. it may have impacted a corner of the phone though but never flipped on the screen side. Well I immediately put my case on after going back in the house and today, actually just about 30 minutes ago, im just scrolling down my Facebook page and I feel and hear a click sound.. at this point I was just thinking my case had shifted or moved in some way but I started looking at my Facebook again and there is now a crack going from about the middle right side of my screen curving up towards the top left all the way to the bezel of the phone just beside the LED.. Now come on.. I know we all make mistakes, but I didn't really expect my screen to crack this early.. especially for the price I paid for this device. Has anybody had this happen to them before, and if anyone could point me to a good screen replacement place it would be greatly appreciated. Thanks.. ps, the top glass or screen is all that cracked.. The LCD and Digitizer seem to be OK.
Sent from my GT-I9300 using xda app-developers app
There are guides to replace the screen only but it's fairly involved and requires things like heat guns. Obviously it voids warranty but having an international version in US means you probably have no warranty at all.
The unit is often sold with screen but you can buy the glass only but you'd want to get a professional to do it I'd say,
Now when you're asking to recommend a good "Screen replacement place" what do you mean? You want us to recommend a shop? Not really knowing anythign about where you are, it's unlikely we can do that. Any descent repair shop / service centre should be able to help.
Please be aware, the general section is not the place for support threads. Should be in Q&A. I've reported the post to be moved.
I have read about the screen replacement and using a heat gun so yes I will have somebody who knows what they're doing get ahold of it. Do you know any long term effects of using a phone with a cracked screen are? Like other damages that could occur? Besides the glass cracking even more than it already is.. Thanks for the reply though, and sorry about the post in the wrong area..
Sent from my GT-I9300 using xda app-developers app
Theres a digitiser under the glass somewhere so it's possible to pierce that after some time if the glass gives. It's obviously weaker now. I would definitely recomend getting it changes ASAP.
Alright :thumbup:. Thanks for the suggestions.
Sent from my GT-I9300 using xda app-developers app
No probs. Good luck!
Hello Everyone,
I did a search but I didn't see anyone else posting something about this, but it seems likes my display glass is starting to separate from my phone about halfway down the body. The glass is now a hair higher that the actual plastic body on the left and I can physically push it down and the screen actually shows a wave, like when pressing too hard on an LCD or touching a non-touchscreen. I was wondering if anyone else was having this issue?
I am trying to determine my best option for warranty service as I used the transfer the upgrade trick on VZW and don't want to throw up any red flags. I also want to keep my battery door because I have the wireless charging sticker on it.
GTiceman said:
Hello Everyone,
I did a search but I didn't see anyone else posting something about this, but it seems likes my display glass is starting to separate from my phone about halfway down the body. The glass is now a hair higher that the actual plastic body on the left and I can physically push it down and the screen actually shows a wave, like when pressing too hard on an LCD or touching a non-touchscreen. I was wondering if anyone else was having this issue?
I am trying to determine my best option for warranty service as I used the transfer the upgrade trick on VZW and don't want to throw up any red flags. I also want to keep my battery door because I have the wireless charging sticker on it.
Click to expand...
Click to collapse
Well that's no good! Sorry to hear that, I've not seen anywhere online either where people are having that problem.
As far as your options go though... Not sure you have many. You can either pay someone to replace the screen, if it's repairable and you can find someone.... Or obviously you'd have to just go for the insurance... I'm curious, how would you throw up any red flags if in fact there is something as obviously detected as your screen? I've not done the " upgrade trick " myself so bear with me if that's a silly question.
Well I might be able to get replaced under Manufacturer Warranty as there are no signs of damage. I also do not have insurance on the phone.
I'm having the same problem, the middle left edge of my screen is lifting up (very slightly) as well. Light bleeds through the edge of the screen and the lcd changes color when I press with moderate pressure. I plan on contacting Verizon for warranty support tmrw.
So I spoke to VZW and they told me that the screen lifting off from the bezel is considered a physical defect rather than a manufacturers defect so it is not covered under warranty support. FWIW my phone has not sustained any major drops or any major damage at all...
Do you guys have the qi sticker on yours? Mine does and it's a really tight fit... I was thinking that maybe it could be pushing out the screen
My Verizon LG G3 screen is now separating from the midframe on both sides in the middle of each side. It is up about a 16th of an inch, can be pushed easily back down but doesn't stay. Light leaks from the edges.
Sent from my VS985 4G using Tapatalk
---------- Post added at 05:10 PM ---------- Previous post was at 04:27 PM ----------
I discovered I had a spare sd chip and spare sim stored under my battery. When I removed them both, reinstalled the battery and qi circle case, the light leaking was gone.
Looks like the G3 is pretty flexible and that the display is not glued down except at the corners. If you crowd it in the back, the display can bulge out the front of the frame. This doesn't mean its broken or defective, just tight.
Sent from my VS985 4G using Tapatalk
Same thing has happened here on the left hand side only. I must admit I decided to store a spare SIM under the battery and a day or so later noticed a raised edge on the left side of the screen. I immediately realised this must be the case and removed the spare SIM but now the left side it ever so slightly raised, I notice this most when using the phone in the dark/dark areas as light bleeds out along that raised edge.
I may try get a replacement but since this is the second thing that occurred with the LG G3 for me (first was cracked camera lens) I may just come to the conclusion the LG cant cut it against my old Galaxy S3, which is still going without fault all these years. Might just be eyeing up a new S6 sometime in the future.
Just coming here to say that this is also happening to my device, only on the left side, as well.
I am trying to activate the warranty to get it fixed.
TTSDA said:
Just coming here to say that this is also happening to my device, only on the left side, as well.
I am trying to activate the warranty to get it fixed.
Click to expand...
Click to collapse
Me too.. Gonna see about getting it swapped
Did you guys bought your phone New from the store ? Like Verizon ?
This issues sound like the aftermarket LCD screens sold on eBay. I have bought 3 LCD screens from eBay. For the LG G2 twice and one for the G3. Once installed and a few uses on the phone, parts of the glass lifts up from the LCD and frame. That's cause they're high quality not genuine LG screens... They don't have the good loca glue on the screen.
I am experiencing the same problem. i only bought it in June 2015 and I don't know how that happened because I haven't even dropped it once.
I am thinking to claim the warranty. Because it seems like the glue has come off of it.
Yup. Mine is doing this too now... awesome! Left side as well. This is my 3rd G3 since July 2014 - I'm done with LG.
From what I've seen on other phones, the screen is often held on by some kind of adhesive. Considering this phone gets red hot if you do two things, like talk on the phone and try to web browse (like so hot it's hard to even hold), it probably slowly breaks down the adhesive holding the screen on.
My vs985 display lifts a bit in the middle along both sides, but only when I have a spare sim or sim adapter attached back there with the battery.
Doesn't take much.
Sent from my Nexus 6 using Tapatalk
i have this problem too in my phone screen...
ivann23 said:
i have this problem too in my phone screen...
Click to expand...
Click to collapse
Same. Light leaks out the Sides
Sent from my LG-VS985 using Tapatalk
A solution would be a case that cover that area of the phone. for example:
http://www.amazon.com/G3-Case-Bastex-Heavy-Protective/dp/B00PIYNE7Y/ref=sr_1_12?s=wireless&ie=UTF8&qid=1448743612&sr=1-12&keywords=g3+case
It's that Wireless Charging unit in the cover that brings the display up. Notice how the bleeding disappears when you take the cover off.
If you're not big on wireless charging, I suggest you perform operations on your backcover and get that bump out of there.
My LG G3 seemed to be having the same problem as well. It has beeen lifting slightly on both of the long sides and if it is on i can look at the side of the phone and see light escaping from the display. I orginally thought the my screen was somehow bent, but out of curiousity i inspected the back on the phone. In that i found that somehow my battery seems to be pushing my display out of the midframe... When i take the battery out the screen returns to the midframe on its own. When i try to put the battery back in it pokes out slighlty then when i put it in completely the display pops back out slightly on both sides again. I dont know how to fix this issue but if someone could figure it out that would be appericated.
jncool101 said:
My LG G3 seemed to be having the same problem as well. It has beeen lifting slightly on both of the long sides and if it is on i can look at the side of the phone and see light escaping from the display. I orginally thought the my screen was somehow bent, but out of curiousity i inspected the back on the phone. In that i found that somehow my battery seems to be pushing my display out of the midframe... When i take the battery out the screen returns to the midframe on its own. When i try to put the battery back in it pokes out slighlty then when i put it in completely the display pops back out slightly on both sides again. I dont know how to fix this issue but if someone could figure it out that would be appericated.
Click to expand...
Click to collapse
Have you tried a new battery? Is your battery swollen? Sometimes they get bloated when they go bad.