I haven't seen anyone post this yet, and I'm hoping I won't draw the usual search you fool comments. I am trying to connect to an IOGEAR GBHFK231 handsfree car device which I know usues a passcode to connect. It pairs without prompting me for the passcode, and when it tries to connect i get a message bluetooth device has disconnected, and the BT no longer shows up in the list.
I am currently using Scotts Cleanrom 1.6.5 without any mods installed, but I have had this problem with stock before unlocking, Nils ICS, Scott's Cleanrom ICS, and a few others ICS and GB.
I have also contacted IOGEAR who says they have not received any reports of issues, and will get back with me if they get any information. I'm holding my breath. Notice the blue color.
Any ideas from this renowned collection of geniuses?
This is a cheapo device by the way, and relaceing it isn't a problem. Just looking for answers.
Thanks,
Matt
Wow no responses yet.. I had it connect one time and was able to make a call using voice dial, but after it was disconnected it went back to paired but not connected, then disappeared when attempting to connect. I'm planning to upgrad my car stereo with a bluetooth calling built in model. Am I likely to have similar problems?
Thanks again.
Am I the only one to experience this problem? anyone using a Bluetooth hands free car device and can verify it working? I'm a little hesitant to buy another and have the same problem.
Sent from my ADR6425LVW using Tapatalk
No comments about searching. See? :-D
You might try Amazon reviews to see if there are any reasonable complaints there.
Not sure where Berlin is but, if you live in the south, the bluetooth device itself may overheat on your dash, and that may cause the issue you describe.
Also, not familiar with BT pairing for your device, but you should be prompted for a pin / code. Make sure you're in BT wireless settings on your Rezound when you are trying to pair. It might be good to "forget" your BT device and start with a fresh pairing attempt.
Sent from my ADR6425LVW using Tapatalk
If you've had the device previously paired to the phone, the phone I'd has changed according to the device. Clear your pair list and re-pair or pair, delete the pair, re-pair.
Sent from my ADR6425LVW using Tapatalk
BT is flaky at best right now with the ICS rom. Mine works most of the time when it wants to. Occasionally I will have to reboot my phone to get it work right.
I have the turtle beach px500 headphones and my phone hooks up to them over Bluetooth just fine. Can make calls, listen to music.
Running innefabilis 1.0
Sent from my ADR6425LVW using XDA App
htc uses its own BT stack. Unfortunately, BT still has too many variables which is why I have never bought the BT peripheral for my pioneer system. Not worth 150 bucks to have it not pair with a phone down the line.
Thanks for all the replies. I've been through stack problems in the past with some car audio bt devices never won one yet. This issue started before I ever unlocked my phone, and I have used both GB and ICS roms with no luck so I'm going to rule that out for now. I've started getting error messages that say I am using the wrong pin to pair, but have never been given the box to enter a pin. So far as heat etc this was working fine on my Dinc, and hasn't been in the car since I switched to the Rezound. I have also connected it to other phones while trying to fix it without a problem. Does anyone have a method to force the box to open to enter the pin, or is there possible a security setting that I need to remove?
Well I figure it out. I changed the bt device to a setting to use 2 phones, then reset it to factory default and it's working now. I don't know why the other resets didn't do the same thing, but it's working.
Related
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Sorry to hear that. I have so far no problems with connecting my phone to my built in BT system. I have a Mazda 2010. I stream music and get incoming calls too.
I used a bt headset for an hour long conference call this morning. No lost connections yet. Reboot doesn't help?
Sent from my MB860 using XDA App
Nope, rebooting doesn't help. BT on the Atrix works just fine with my Panasonic house phone that has BT on it.
I had the same issue today in my 2010 Dodge Ram. Captivate worked great in it, but the Atrix dropped the BT/Call after 30-45 seconds or so. I haven't noticed it dropping connection when I'm not using the phone (I have an icon on my ent/nav headunit), only saw the icon disappear when on a call.
Exwoodchuck said:
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Click to expand...
Click to collapse
OK, so I messed with it some more...
If I'm super-fast, I can dial from the car's BT system-- and the name of the phone does appear on the car's Nav. That is, until the phone and/or car drops the connection.
I've asked for help on Motorola's forum, and been tracking down a Product Manager @ ATT to get the word up the chain.
I have the same issue with my 04 3-Series. I posted about this in the Problem forum.
No bt issues here. I used it yesterday with a car kit/fm transmitter to stream Slacker and nav simultaneously to my stereo for a couple of hours and it worked great.
Ziuck said:
I have the same issue with my 04 3-Series. I posted about this in the Problem forum.
Click to expand...
Click to collapse
Think we've got the same BT ULF's in our car. Please let me know if you find a solution, and I'll do the same.
mgymnop said:
Sorry to hear that. I have so far no problems with connecting my phone to my built in BT system. I have a Mazda 2010. I stream music and get incoming calls too.
Click to expand...
Click to collapse
Can you skip forward and back and pause?
I could with the iphone but have not been able to get it to work with android.
The weirdest bit is that I got it to work for Pandora ONCE... then never again.
I think it has something to do with the way android treats certain devices... I have motorola BT stereo headphones that the controls worked for WinMo W7 and iphone, but do not work on any android device I've tried.
I also lose connection with the in car BT occaisionally but not very often and can usually get it to reconnect without much hassle.
2010 mazda 3.
Exwoodchuck said:
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Click to expand...
Click to collapse
Just because it worked with your iPhones doesn't mean the BT module isn't faulty...it might just have trouble accepting connections from certain things. Not to say the phone's *not* at fault, but don't assume it's the phone when there's a chance it could still be the phone.
I have a kenwood bluetooth module in my receiver that worked perfectly with every phone until I got an iPhone 4 (even previous iPhones worked fine). It wouldn't connect and finally when I got it to work the sound quality was horrendous (most people couldn't understand a single word). I thought the phone was obviously bad until I contacted Kenwood and they sent me a beta driver for the bluetooth module in the receiver. Updated the driver and it worked perfectly.
I agree- the BT module *could* be fault, but given that it works with all iphones and my BB Bold, I'd have to say that it's more than likely something to do with the way the Atrix/Android handles the connection.
Others are now chiming in on the Motorola Forum about this issue- including someone who has a newer BMW BT module than I have - he's also got the same issue. There's also a Dodge owner earlier in this thread that's got the same problem.
On a whim, I copied 20 contacts to the SIM, thinking that might be the problem.
Same results.
i also had bt pairing problems with my ford sync, and it seems to be android related as it also happened with my n1.
couple things to try that should help: disable wireless and make sure you aren't using the power widget on one of your home screens. also, i used autostarts to unbind the media button pressed event, and between those three things, the bt works fine...
Tried an experiement-- copied some contacts to the SIM.
Same issue- phone connects/disconnect/connects/disconnects for good.
Exwoodchuck said:
I agree- the BT module *could* be fault, but given that it works with all iphones and my BB Bold, I'd have to say that it's more than likely something to do with the way the Atrix/Android handles the connection.
Others are now chiming in on the Motorola Forum about this issue- including someone who has a newer BMW BT module than I have - he's also got the same issue. There's also a Dodge owner earlier in this thread that's got the same problem.
Click to expand...
Click to collapse
Apparently you read my post...but didn't understand it completely.
My previous receiver worked *PERFECTLY* with all phones but the iPhone 4. I used about 20+ phones with it without a single problem...but the iPhone 4 wouldn't connect 3/4 of the time, and when it did it didn't transfer any contacts and when I made a call the sound quality was *very* bad. I obviously assumed it was the iPhone 4 until I tried another one with it...turned out it *WAS* the receiver having an older firmware that wasn't compatible with the iPhone 4.
The reason a lot of Audis and BMWs aren't working with a few Android phones (the Atrix being one of them) isn't because Android is designed poorly...it's because the firmware in the receivers doesn't handle the Android setup well. The reason most people can connect but can't get contacts is because the way BMW/Audis poll for Contact lists doesn't work with Android. The car manufacturers haven't spent the time required to realize this and put out a correction. You should be complaining to BMW or Audi about this (whichever type you own) and trying to get them to release an updated BT Stack for your receiver (they might say it's not possible but it is).
Thanks for the clarification.
I doubt that BMW is going to release a firmware upgrade for my BT module - its out of production, and it's already 'state of the art', circa 2006 when they stopped producing them. I've read of other issues with newer BMW and other cars still having issues with the Phonebook upload, which is where I think the problem lies. It doesn't seem to be isolated to older cars either- I've read of 2010 models having the same issue I've got, and not just from European makers.
Digging around, this is a common theme with Android and BT not playing nicely-- many other phone manufactures have released patches/updates to correct similar issues, and I'm hoping that with the Atrix being the 'biggest and baddest', that Motorola sees fit to do the same. I've got a $600 fully integrated factory BT system thats now useless, and I'd sure like to have it working again.
I sometimes forget that I've got another BT-enabled car to test on -- a 2010 Audi A3.
My Atrix paired with no issue, then popped up with a message in the Notification area about allowing access to the Contacts. Ahh-hah! When paired to my BMW, I never get that message. So... the BMW appears to be unable to complete the handshake for PBAP access, and when it fails, it drops.
After syncing with my BMW I do not get the PBAP confirmation.
I did not get the confirmation with my Inspire 4G either but that phone DID work just fine. Contacts and audio would work and never had a drop out when I had the phone.
So there is a way to "fix" this issue without updating the vehicles BT.
Tested with my car bluetooth with 2 calls for ~30 mins in all today morning. Worked fine. It stayed paired on all the time.
I know there are a variety of posts of many flavors in regards to OEM in car bluetooth handsfree systems. Some for unbranded i9100, some for the AT&T i777
For anyone out there with the knowledge: Is there anyway to find a task automater (like a macro) to lets say automatically activate the bluetooth button for the paired device, lets say 1 second after Bluetooth turns on. In connection with Auto Bluetooth app (like the ones which turns on when motion is detected) it could be automated. I would do it, except I don't know how to write program code.
I am thinking like "if bluetooth turned on, wait 1 second, trigger paired device input" . Because in that case it would connect (automatically) in most cases I though many many people posting around here.
Anybody any idea?
I am trying to connect my Galaxy S2 with they system in my 2011 Jaguar XJ. I never had a problem with my BlackBerrys. The BlackBerry autoconnects the moment I start the car and all functions work.
Absolutely not so with my S2. It seems that differnet car manufacturers differing systems which use BLuetooth differently. Some work, some don't .
Let me clearify the problem. Phone does NOT AUTOCONNECT and it drives me nuts. Before i just got in the car and never pulled the phone out of my pocket. Now I have to pull it out and manually connect.
I am posting as I may save some of you some time. I tried everything up and down the list. About every Bluetooth apps in the market place. Free or paid. Really pretty much all of them. Nothing worked. I upgraded to the (leaked) UCKJ1 and back to the original UCKH1. I rooted and unrooted.
To no avail. All I can do is use a shortcut widget to save me a few menues to navigate.
So for the ones with the same problem; you know all the things I tried. Don't waste your time.
It takes two devices to successfuly connect. If a connection doesn't happen, you can't blame just one device. My ISGS2 auto-connects to all of my devices (AV receiver, headset, PC, car, portable speaker, G-Tab) automatically every time. I get you're upset, but you can't single the phone out alone. As for cars, in the ISGS2 forum, non-iDrive (older) BMW's were the majority of the problem.
Same here. I have no problem auto connect to my BT devices. But when it comes to BT auto connections, problems are common. Both sides of the BT connection can be the cause.
Well depending on the year, make and model of the car with bluetooth. Really need more information. What Barry said is oh so true and usually anyone can tell you what their experience is. My experience with my daily driver's system *Alpine CDA 9887, Alpine KCE-BT400 made by parrot*, works flawlessly. The only time I ever had to manually connect was right after getting my sgs2 and even my captivate connected properly unless I was connected to my jawbone icon when I jumped in my truck.
HTH,
Charlie
Mine connects flawlessly in my 2010 Camaro SS.
Im in a 2011 Camry SE, and with stock ROM it connects automatically. With CM7.1, I just have to take it out of sleep, by turning on the screen, and it connects. Not a big deal.
Sent from my SGH-I777 using XDA App
Hi, Thanks to all for the responses. I completely agree that it takes two devices to do it right and I am fully keeping that in mind. I have 2 more cars I can try with. So I will check if it works with my wife's Lexus and with my Clarion system in another car I have.
It just is, that my BlackBerry (which I don't miss at all) simply did the job perfect. Obviously I can't tweak anything on the car side as that is next to impossible. There is no open source code and all is so proprietary.
So the only hope I have is to figure out a way to teach my SGSII.
Again thanks for the input. I do absolutely LOVE my Galaxy S2 (i777) therefore this is a simply irritating that I have to push buttons when I get in the car.
Hearing that it works for most of you is well, good for you and not so good for me.
Blaze9 said:
Im in a 2011 Camry SE, and with stock ROM it connects automatically. With CM7.1, I just have to take it out of sleep, by turning on the screen, and it connects. Not a big deal.
Sent from my SGH-I777 using XDA App
Click to expand...
Click to collapse
dmnall said:
Well depending on the year, make and model of the car with bluetooth. Really need more information. What Barry said is oh so true and usually anyone can tell you what their experience is. My experience with my daily driver's system *Alpine CDA 9887, Alpine KCE-BT400 made by parrot*, works flawlessly. The only time I ever had to manually connect was right after getting my sgs2 and even my captivate connected properly unless I was connected to my jawbone icon when I jumped in my truck.
HTH,
Charlie
Click to expand...
Click to collapse
Well, I will experiment a bit more and I will share what I will find in case others have similar problems.
This reminds me of a blog post ages ago called "Bluetooth needs a dentist"
The state of Bluetooth compatibility is abysmal in general... What is exceptionally sad is that 4-5 years ago or so, one of the most relibale and compatible Bluetooth stacks around (BlueZ) got a bunch of nastygrams from the Bluetooth SIG regarding failure to run the "offficial" compatibility/interop tests.
The short summary: Bluetooth compatibility is an epic nightmare, on both sides of the coin (host and device).
Entropy512 said:
This reminds me of a blog post ages ago called "Bluetooth needs a dentist"
The state of Bluetooth compatibility is abysmal in general... What is exceptionally sad is that 4-5 years ago or so, one of the most relibale and compatible Bluetooth stacks around (BlueZ) got a bunch of nastygrams from the Bluetooth SIG regarding failure to run the "offficial" compatibility/interop tests.
The short summary: Bluetooth compatibility is an epic nightmare, on both sides of the coin (host and device).
Click to expand...
Click to collapse
Hello,
I have to fully agree with Entropy512. Bluetooth compatibility is a disaster. Especially after all the years around. Not sure who, what and where is deciding on BT specs, drafts and so forth.
I know that with car systems it is a hit and miss. But it doesn't have to be. We all know that. I was digging on my good old Jaguar forum. What I found confirms exactly what we are saying.
Earlier Samsung Androids barely could hold a connection on Jaguars systems. Just with later versions and Gingerbread that was resolved. And none of the Samsungs autoconnect to any Jaguar system. And that is the same for Audi, Merceds and Subaru and probably some others. According to the Jag forum Samsung knows about this and worked on it.
But here is the main problem. On my wife's Lexus and on my Clarion head unit in my van it works like a charm. Automatically connects without a hitch. I understand Samsung can fix that but than it may not work on other cars. But how come BlackBerry was able to do what the Samsung unit can't???
And yes, some features like phonebook, direct dial and so forth are totally hit and miss. How do car unit manufacturers test? With what? Just one phone from 3 years ago? Same with the phone manufacturers. Is anybody talking? Seriously, why can't car head units manufacturers and phone manufacturers not figure out how to get on the same page? Car BT is becoming a standard equipment. So do BT enabled phones, no matter smart phones or what have you. There are not that many head unit manufacturers. So they can't agree on a standard which then can be used by the devolpers for a decent BT stack for phones? Completely ridiculous. Can make phones talk to you like the Apple Siri but can't get a bluetooth connection.
OK, I got that off my chest. Now I will try to get to work. All I can do is working on the i777 side, because there is no acces to anything on the Jaguar side.
Funny thing is, my phone is always stating phonebook request when I get in the car. Eventhoug I turned phone book off in the car. So the phone "hears" the car. Just without hitting the profile for the car it won't connect.
Auto connect to my Mazda 6 no issues. Same with all my other phones.
Sent from my SAMSUNG-SGH-I777 using xda premium
cpcrazyfly said:
Auto connect to my Mazda 6 no issues. Same with all my other phones.
Sent from my SAMSUNG-SGH-I777 using xda premium
Click to expand...
Click to collapse
Do you have problems with the Mazda taking too long to switch from "Music" mode to "Headset" mode, thus the vlingo voice prompt timing out? My mazda has that issue and it makes vlingo in the car pretty much useless.
I don't typically use voice commands but ill try. It has no issues taking and making calls then going right back to google music streaming.
Sent from my SAMSUNG-SGH-I777 using xda premium
I am also experiencing sporadic problems with my SGS2 and 2011 VW Golf using BT. About 75% of the time, it auto-connects fine when I start up the car. The car lets me know it linked and I can make/receive calls through the car's BT system fine. Address book loads as well (though does require a secondary authorization on the phone the very first time you use it).
However, every once in a while it either can't "find" the phone, or goes into a continuing looping state of "paired/not-paired". Generally when I actually want to use it! When it can't find the phone, manually searching for it (on the car's system) usually rectifies it temporarily, but it may go to unpaired a few minutes later. And on occasion, it simply can't find it at all. When I reboot the phone, or disable/re-enable BT on the phone itself, this problem usually goes away. This makes me think it's more of an issue with the phone then the car.
I too came from a BlackBerry torch and never once had a single pairing problem with my car.
When paired, media streaming generally works well, but occasionally I have to stop/restart it a couple times in order for the car to 'see' the media stream and allow me to chose it as the input.
The problem that I have is that the sgs2 will not report signal level to the car, so the car always shows full signal, even if i have no signal.
And it doesn't connect to the car unless the phone is in the car when the car starts. If bluetooth is turned off, or if I leave the car and go out of range, I will have to open the settings and force a connection.
Problem Solved, Autoconnect now working
Problem solved, read on:
This seems to apply to a variety of other vehicles, namely Jaguar, Mercedes, Audi, some BMW, Nissan and Subaru.
You can get your phone bluetooth auto connect to your vehicle by trying the following:
Attention, I believe this works for rooted phones only.
Get a app such as Titanium Backup Pro or MyToolbox.
under System Apps freeze "Bluetooth Share".
Now my phone automatically connects to my Jaguar XJ and all features seem to work. Having gotten around to check the phonebook yet. But all recent number log show and all seems to work.
Attention: I believe that may only work for rooted phones.
metalco said:
Problem solved, read on:
This seems to apply to a variety of other vehicles, namely Jaguar, Mercedes, Audi, some BMW, Nissan and Subaru.
You can get your phone bluetooth auto connect to your vehicle by trying the following:
Attention, I believe this works for rooted phones only.
Get a app such as Titanium Backup Pro or MyToolbox.
under System Apps freeze "Bluetooth Share".
Now my phone automatically connects to my Jaguar XJ and all features seem to work. Having gotten around to check the phonebook yet. But all recent number log show and all seems to work.
Attention: I believe that may only work for rooted phones.
Click to expand...
Click to collapse
I'm going to try this...
I've been having trouble with it automatically connecting to my 2011 WRX. My iPhone 4 always connected immediately, no problem. But the GS2 has yet to automatically connect, ever. It is paired fine and if I go into the Bluetooth settings, it is paired OK and I can manually tell it to connect. I've tried deleting the connection both from my head unit and the phone and recreating everything multiple times. Still no luck.
I'll try this and report back.
Bluetooth is def one of those technologies that could be enormously awesome but often has so much "fussiness" with it (due to incompatibilities or quirky behavior between varying BT devices) that it can easily become a right-royal PITA, IMO.
I've had quite a few Android phones over the years, now, and tried running both stock OS and many different ROMs on them with one of the expected primary functions of my phone to be as my main music player, including streaming music via BT/A2DP to my car stereo and this one function has ALWAYS proven to be the most frustrating experience. So yeah, I'll fully agree that whomever is "calling the shots" with setting up guidelines and specifications for BT and BT-based devices needs to get themselves an iron fist and put an end to this crap of inconsistent behavior and general flakiness.
When I got my AT&T SGS2 I was shocked to see that Samsung had done something to enable their stock music app to be able to transmit song metadata via BT. Android thus far has only supported AVRCP 1.0 (AFAIK) while you need AVRCP 1.3 (or higher) to be able to have metadata transmit over BT. At first I was ecstatic that FINALLY I could see my song info from my phone displayed on my car stereo while connected via BT. But then I found out that with the SGS2 and the stock music app my car stereo could no longer successfully send play/pause/forward/reverse commands to my phone! D'oh!!!
So then I went back to Poweramp (what I had been using for my primary music app on my previous phone; a Nexus S) and of course it wouldn't display the song metadata. But the big shocker was that it also couldn't recognize control commands issues from my car stereo! Not cool!
I did much tinkering and research and finally found that the music app PlayerPro would successfully work with my head unit (but still no metadata, of course) and so that's where I'm at.
Ridiculous, IMO. Nobody should have to endure such frustrating behavior with BT devices. I really wish somebody could straighten this kind of mess out in regards to Bluetooth and get things to "just work".
No luck for me. Freezing the Bluetooth Share did not fix my auto-connect problem.
ack154 said:
No luck for me. Freezing the Bluetooth Share did not fix my auto-connect problem.
Click to expand...
Click to collapse
OK, you can try one more thing;
Freeze all of those files: BluetoothPBAP, BluetoothShare and BluetoothAvrcp. If you have any other entries you can try freezing them, too. Just everything EXCEPT anything with a name like Brcm or BrcmBluetoothServices.
Just try it. And MAKE SURE to wipe cache after freezing, or better reboot. Also you want to make check they are in a "frozen" state after rebooting. I used "MyToolbox" and it worked perfect.
I haven't checked if I can still stream music, but I never use that anyways. I froze all of those and started unfreezing one by one. The experiment showed that in my case I only had to freeze the BluetoothShare. You may have to freeze the others, too.
Let me know how ot works. I am curious now.
hello, I am running the current public release at the time of this post(v1.1). I have a Jabra SP700 bluetooth FM speaker for my car. I am uncertain if this is a fault of the rom or the hardware of my bluetooth speaker. I am leaning more towards the bluetooth but I figured I would ask the community.
I play music through this to my car stereo. Frequently the bluetooth drops the audio connection at random times. The phone and speaker say the X2 is connected, but the audio ceases. Within a minute the sound will play through the phone speaker not the bluetooth. Then the bluetooth will say "disconnected" and begin searching to reconnect. My X2 will state the bluetooth is still connected. In order for me to get the phone connected, I need to power off the bluetooth then disable and reenable bluetooth on the X2.
I believe this has happened with previous versions, ive been using eclipse since it started. Although I cannot remember if it works correctly with the bluetooth bone stock.
I am leaning towards the bluetooth since the bluetooth is about 2 years old now...but I was wondering if anybody used a similar bluetooth piece and experienced similar issues. Thanks!!
Ok guys. Let's try this thread over.
Anyone want to help this gentleman? We're not going to argue or derail. If you can't help this guy, don't respond.
OP, search while you wait for an answer.
There is a known issue with the bluetooth function on 1.1
I had heard people saying that with the newest ((1.2rc3)) that the issue had been fixed.
I don't use bluetooth do I cannot confirm but that might be the issue
I didn't think that older BTdevices would become "obsolete" . I thought any newer phones that support bluetooth would encompass all older BTdevices not exclude them. I can see an older phone not connecting to newer bluetooth but not older bluetooth not connect to newer phone.
Nitro tweeted that the new eclipse final should be out tomorrow. Hr has known about the bluetooth bug for a while so I am sure it was a priority fix.
It is possible tho that there is something faulty with your bluetooth device. Have you tried contacting the manufacturers of it to see if that is a known problem with that device? They may be able to help troubleshoot it also.
Thanks ash. As usual you are helpful and nice the speaker is way out of warranty. Ive owned it for 2 years. The battery os startong to go too. I never doubted the compatibility of the speaker...just the performance. It has acted odd in the past. I did not notice an issue initially with the X2. Since it started acting up i was pretty sure it was the bluetooth just showing its age and starting to malfunction. Well at least i do not have to buy anothee speaker just yet
Sent from my DROID X2 using XDA App
Thanks
Even if it is out pf warranty they may be the type of company who is willing to repair or help with problems just to keep your loyalty to their products. Who knows you may be able to talk them into a rebate on new product or a coupon or something . Might be worth a shot. Just be site you tell them you promote the product to people you know and in forums you post in. I have been looking for either a wired or bluetooth speaker for my x2 and not sure what to go with. . I saw one in the VZW store I
that looked nice but $199 is a bit steep for a speaker for me lol
And it seems like any other speaker I find (wired or bluetooth) is labeled do I ipod /iphone etc... im thinking the wired would work okay((headphones jack type)) but am not willing to shell out the 50$ that ill only get back in store credit for opened electronic in a store I barely shop at lol. Im sure ill find something sometime and ur post introduced me to a different one to look into. Curious if new eclipse final will fix your problems. Good luck.
Its odd that it will work for a while and then cut off. Wonder if it may be the "receiver " in the device not working correctly. Maybe something wiggled loose. Might be worth taking it apart((if possible) and checking where things connect to each other it giving it a wipe down and clean it up. Maybe dirt is interfering with something inside due to its age.
Or IT'S ALL YOUR FAULT. YOU USED IT TO MUCH FOR WHAT IT WAS DESIGNED FOR AND IT IS DEAD NOW ...lol j/k...im sure something can be done to fix it if it isn't eclipse that is causing the problem. ..its just a matter of is it worth the time to fix or buy a new one..
It is all my fault!!!! Haha. Well that is an idea....maybe i will try. If i can make a suggestion, the droid roadster is pretty cool. Works well and is user friendly! I tested it for a while and liked it.
Sent from my DROID X2 using XDA App
I have a bluetooth earpiece that I use with my old Razr and it works fine with my DX2 so I don't think age has much to do with compatibility. Wear and tear probably plays more of a factor.
I do pair my DX2 with my Touchpad (WebOS, not when booted in CM7) and I can make calls great on the TP but because the default bluetooth.dun is missing from Eclipse I can send sms with my TP. Not an issue but something to consider if you are shopping and comparing specs to see if you nifty new devices will work with your phone. The devs pull out the blur and bloat because that is what we want but it can change how devices talk to each other.
I have a set of moto rokr hd headphones that I use all the time and I have had this exact same issue with eclipse. The phone still says it has a connection but no audio is playing through my headphones. The only way to correct the issue is to turn off the headphones and turn off bluetooth on the phone and restart them both. It will happen completely at random times. Sometimes I will use them for a couple hours before it hours, but sometimes only 15 min. Its def eclipse, I don't think moto headphones have a compatability issue with a moto phone
Hey guys, I just got my rezound yesterday and I'm having trouble getting bluetooth to connect to my Kenwood head unit in my car. When I attempt to connect, it doesn't prompt for a password/pin it just says it was unable to connect because the pin was incorrect. Anybody else having this problem or know how to help? Any help would be awesome! Thanks guys!
Sent from my GT-P7510 using xda premium
Can anybody help me?
Works fine with my Pioneer in my GMC Terrain. Just had to make the phone discoverable and search for the stereo. The stereo told me the pin and the phone asked for it. I know this does not help but it does work.
It could be the BT profile in your stereo so check with the manufacturer
I'll try that. With every other phone i've used with my Kenwood it would prompt me to put in the pin and I put it in and everything worked fine. Maybe I have to do something different with this one. Thanks for your feedback though, man. Seems like 75 other people had nothing to say. Lol.
I figured it out. My Kenwood only allows 5 devices to be registered to it. Seeing that my Rezound was the 6th device it rejected it, so I deleted the old devices registered, so now it works fine. Dumb mistake on my end, nothing wrong with the bluetooth connectivity of my phone. Thanks guy.
Well I have searched high and low and have not found an answer yet so here goes.....
I have a Pioneer AvicZ130BT stereo in my truck and I have just switched to a Photon from an EVO 4G. I am having issues with connecting to the head unit over BT. It will work some times and sometimes it will disconnect the phone and shut off the bluetooth on the phone.
Q. Are there any updated or legacy BT drivers that I might be able to try to get these two to play nice?
Q. Is there an App that might be helpfull.
Any help will be appreciated.
SexyMoPho said:
Well I have searched high and low and have not found an answer yet so here goes.....
I have a Pioneer AvicZ130BT stereo in my truck and I have just switched to a Photon from an EVO 4G. I am having issues with connecting to the head unit over BT. It will work some times and sometimes it will disconnect the phone and shut off the bluetooth on the phone.
Q. Are there any updated or legacy BT drivers that I might be able to try to get these two to play nice?
Q. Is there an App that might be helpfull.
Any help will be appreciated.
Click to expand...
Click to collapse
Are you running on stock?
I know certain rom/kernel combos are having Bluetooth issues. I am on cm9 with the original kernel and connect to my blau deck in my bimmer and a pioneer deck in my blazer no problem.
Sent from my MB855 using XDA
Yes the phone is stock but has root through the All In One Root just for hotspot. The phone had issues pairing in the parking lot of the Sprint store but I thought I would be able to work it out. I have tried just about everything but can not get the phone to connect automatically or consistently.
My EVO worked perfectly. I spend alot of time in my truck and this will be a deal breaker if I can not get the phone to play nice with the truck.
I have been having similar problems with my Bluetooth. My keyboard disconnects randomly and my headset often disconnects. I posted a question about updating Bluetooth stack, but no answer as of yet. I did try cm9 and the keyboard seemed to work better. However, i didn't use Bluetooth nearly as much while on cm9.
For me not a deal breaker, but i am hoping the motorola update to ics will fix things.
Sent from my MB855 using XDA
UPDATE
Just wanted to say that the phone is connecting very well now and seems to be streaming Pandora and other audio just fine. I did download some 3rd party apps like bluetooth manager and car dock settings that do help in configuring the connection better. I also think that I may have been a little impatient waiting for the phone to connect automatically and may have been causing more issues than the phone. My Evo connected very fast and this phone is just a little slower but I can live with that. So in short, the phone is working as it should and I will stay a SexyMoPho for a while longer I think.
Thanks to all
What did you do?
SexyMoPho said:
Just wanted to say that the phone is connecting very well now and seems to be streaming Pandora and other audio just fine. I did download some 3rd party apps like bluetooth manager and car dock settings that do help in configuring the connection better. I also think that I may have been a little impatient waiting for the phone to connect automatically and may have been causing more issues than the phone. My Evo connected very fast and this phone is just a little slower but I can live with that. So in short, the phone is working as it should and I will stay a SexyMoPho for a while longer I think.
Thanks to all
Click to expand...
Click to collapse
what did you do to get it working better?
Scorpio0378 said:
what did you do to get it working better?
Click to expand...
Click to collapse
YMMV:
This worked for me.
su to root:
Code:
rm -rf /data/misc/bluetoothd/*
This nukes your Bluetooth (bluetooth daemon) stored settings. Handy if you've dirty flashed any ROMs.
I found this here:
http://sandeep.wordpress.com/2011/07/02/this-is-why-i-love-my-android-phone/
Disclaimer: I'm not responsible for your phone or command line fowl-ups. If you know what you are doing, have at it. If not, research it.
Edit: In the interest of due diligence, I have to add that there was also a firmware update for my Pioneer DEH-80PRS. Between nuking the Bluetoothd settings on my Android and updating the Bluetooth Firmware on my Pioneer car stereo, I have had flawless operation ever since. Pioneer has a disclaimer that if you don't have an IPhone, you don't need this update... I think they fixed something they aren't admitting to. You see this often with big companies that throw things in under the radar.
http://www.pioneerelectronics.com/PUSA/Car/UnAssigned-Content/Firmware+Updates/Optional+Bluetooth+Firmware+Update+for+Select+2012+Pioneer+CD+and+DVD+Receivers