my htc p3400 (new gene) is struck during update, i mean its showing an error.
ERROR [266] : UPDATE ERROR
The Update Utility cannot get response from your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone.
Please help guys...
nithin_bablu said:
my htc p3400 (new gene) is struck during update, i mean its showing an error.
ERROR [266] : UPDATE ERROR
The Update Utility cannot get response from your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone.
Please help guys...
Click to expand...
Click to collapse
Male sure yo have removed SD card and kill activesync.exe on PC.And also run it as an administrator in WIn7
Related
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
donot ever try thru SD card.. there is a chance that you may brick your device.
Goto bootloader mode first then u run DSUU.
Now after i did that, it dosent work with DSUU .it show "error connection".and my divice shows the upgrade fail
How many files you have in the upgrade directory? Normally it should contain 6 files:
- Device Software Update Utility.exe
- diskimage_Ver.nb0
- EBOOT.nb0
- ExtendedRom.img
- nova_pda_033105.mot
- vl1d_pda_Ver.mot
It will always shown connection error if one of these files is missing
I have all of them,
It seems feasiable to full downloadig the Rom from SD(memory card), but i need mor files:
"diskimg.nb0 , eboot.nb0 , dm.nbo , flash.img , agent.mot , mot.mot , CPLD.img , assetInf.img , extended.img , Mdoc.img"
If it's possible to upgrading with them how can i rech them ?
hello...!!!?
can enybody help me with this case? I need Your Help. Please. . . .
shaemna said:
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
Click to expand...
Click to collapse
Why did you do this?! No one gave out instructions to flash anything using SD CARD in the first place! Of course you will get connection error because bootloader is not functioning. Remove your SDCard, start bootloader mode, and flash the normal way.
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
shaemna said:
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
Click to expand...
Click to collapse
can you go into bootloader mode?
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
shaemna said:
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
Click to expand...
Click to collapse
I'm sorry. I don't get you. You can go to bootloader, but you get an error. Can you post a screen shot of the error? so, I will know what to do.
How can I uplod picturs?
server is busy it get me Network Error (tcp_error) and cant upload it
the doucument of it is:
(the upgrade page)
Your Divice software is about to be update from:
divice CE image version:0
divice Radio image version:
to:
CE image version: 7210621
Radio image version: R060711N-MN2ARC-RS00011
.......
PLEAS CLICK update to continue
when i click upgrade it show me the fowloeeng error
ERROR:CONNECTION ERROR
THE DIVICE SOFTWAR UPDATE IS HAVING TROUBLE CONECTING TO YOUR DIVICE
PLEAS CHEKE
1)YUOR DIVICE IS PROPLY CONNECTED TO THE USB CABLE OR ...
.
.
.
now what should i do?
do you have any other USB to mini-USB cable? try changing it... The ones used for SD Card readers or Digital Cameras are the same, and do it again.
i do that in all of my USB ports and they are same and get me error conection again
Is there any wey else to inistall a ROM on my divice?
1) Is windows recognizing your device?.. (Do you have activesync installed?)
2) Did u try using different USB cable ?
3) Are you logged on as administrator?
4) Did you remove SD card before going to bootloader mode
5) What is the screen content when you go to boot loader mode
6) Before connecting the device go to bootloader first, then connect the device and then run DSUU
7) Activesync may install device drivers for your device so try installing activesync?
Thanks
when i get my divice in to the bootloader it's display:
===========MN2 Bootloader=
Jun 13 2006 20:41:44
copyright (c) 2006 Quanta cor
poration
CPLD Ver: A0060109
***********************
*Using '<-','->', 'Enter' *
*to choose what you want *
***********************
(1)debug module through UART
(2)jump to DM
enter your selection:
when i conect it to pc( as administrator user) the fallowing line was shown:
USB connected , waiting for download command...
and my computer beeping and found new hardware but not connected to activesync(4.5) , then i start DSUU and when start to upgrade computer show me "ERROR CONECTION" and my divice show me this note:
! ! ! Please use DSUU in OS mode and sync with pc first ! ! !
Usb transfer Fail
please help me
1. We get the most first sewing of Xda-atomexec-eng-20060614_r060428n_ex0028.exe (only by this sewing restore was able)
2. We drag out the files of eboot.nb0
3. We copy on miniSD in a root directory.
4. We insert miniSD in Pocket, enter in bootloader (Camera+SR)
5. We wait inundated while.
6. We take out a miniSD, enter in bootloader, start sewing on PC, connect to USB (it is needed to put to death in the processes of AS)
We are sewn!!!
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
tiagofa said:
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
Click to expand...
Click to collapse
if u are in Bootloader mode the one in three color mode.. U can downgrade surely with PDA viet temp.
In Boot loader mode just reconnect your device to pc through USB . and launch the PDA VIET program..
It should be work.
doesn´t work..
is there any connection with SD slot card doesn´t work ?.. ?? :S
help.. :S
u r using vista right?
u should do that with xp
be sure that with xp u can fix it 100%
no, i+m using xp.. still doens´t work..
i think my prophet dies :S
try flashing NVID wm5 when in bootloader. if you were successfull flash HardSPL and after that you original ROM!
First, disable any firewall
Put the prophet in bootloader (3-clored screen) by pushing CAM button and punching the reset hole at the bottom. When you realease the stylus, the colors should appear.
Then, before connecting your prophet to the PC, first DISable the "Allow USB connection" option in the connectionsettings box of ActiveSync.
After that connect the bootloadermoded Prophet to your PC, it conects as an ordinairy USB device. Then run the RUU of your choice.
probably the better idea is to send a snapshot of your display in fault mode.
do that with a camera. it could be useful to identify the state of your error.
i'm not skilled but here you can find a pool of powerfull developers.
jork
problem solve
problem.. usb port lol :S
Hi!
Recently I try to flash my SPV m3000 using HardSPL and then shelltool (with a rom wm6 HTC Professional)
And now, my pda still on orange page where I can see SPL and IPL version.
(IPL : 2.16.0001 SPL : 2.16.0001)
If I try something :
Hardspl doesnt find my mobile device!
Shelltool doesnt work and still not responding!
Any RUU say ERROR [260] Update error : The update utility cannot connect to your PDA phone!
I try that in bootloader mod. My PC see my device (in "Gestionnaire de périphérique" I dunno how to say that in english!), but Windows Mobile Device Center doesnt!
Can someone help me please?
Thx
I think that basically your device is unknown to windows enter bootloader manually yourself, do not connect it. Then open windows mobile devicecenter and select connection settings and untick the allow usb connections then connect the device and try to flash it.
I also hope you realise that you have a G4 device and are not trying to flash a g3 hardspl go here to get hardspl for g4
http://forum.xda-developers.com/showthread.php?t=332320
windows Vista is not recommended for HardSPL,its not compatible,still got issues.Try to do on winXP pc and use ActiveSync 4.5,there shudn't be any problem.
Well! there's no 'G3 HardSPL' as yet!!! its only 'HardSPL' for G4 devices.
Thx all!
Ill try on XP..
Ill say the result..
So I try.. and always the same message ERROR NO DEVICE DETECTED
I try that with XP Activsync 4.5 and my spv connected in bootloader and connected less bootloader!
So if u have any other idea.. Welcome!
You have connectivity problem,to verify if the phone is establishing connection with pc via usb cable,get the phone into Bootloaders then connect it with pc through usb cable and check small usb appear at the bottom of the Bootloader screen,if its there,than its establishing,otherwise there's a connection problem.Either usb cable is faulty or the mini usb port of the phone is damaged.
...
Its written USB in bootloader and I can see my spv in device manager..
So I explain what I think.. Maybe theres only the bootloader of orange on my spv on no more wm5.. and I cannot flash only the bootloader..
If any idea come.. Already thx!
i went to this thread
http://forum.xda-developers.com/showthread.php?t=472169
to upgrade my htc p3400i which has a s/n HT 814. I first tried the olipro method but it failed and my device was dead the i tried to unbrick it by using orefkov method as explained in that thread, when i reached this step
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
i get this error of error 200 , invalid update tool of which i am attaching a image . Please help me i am very new
make sure that USB sync is done properly before running RUU...i.e drivers properly installed.