Related
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
...with the build quality.
Put my nice, shiney, new tablet S into my work laptop bag this morning, with nothing else in the laptop compartment and when removing it noticed what I thought was a smudge across the top of the black plastic (the curved edge just above the screen). Low and behold where the tablet had slight movement against the 'fabric' of the laptop compartment (this is a padded, soft material specifically for holding laptops), the plastic has worn away! The material of the laptop compartment has actually rubbed the plastic away, removing some of the nodules and worn the plastic down in a strip across the length of the top!
For £399 I'm not impressed with SONY's choice of materials, as this is clearly poor quality were the structure can literally be worn away by fabric!
I'm going to try take this back I think, as this is unacceptable in my eyes and such poor materials for this price in not on.
Please fellow owners, take this as a warning and purchase some protection, as clearly SONY haven't bothered with the quality control aspect of this tablet.
I just chuck mine into my backpack and haven't had a problem yet. Maybe u can exchange it?
Sent from my GT-I9100 using xda premium
Weird. Post a picture.
I've been popping mine in and out of a very oversized laptop bag and to be honest not taking the best of care of it but mines fine.
Same here...pretty much just throwing it around and nothing yet...
This seems very strange, I have mine in a GIMP case (made of 'fabric') and it is fine. I would take it back and see if it was a dodgy one, or make sure the fabric is not infact sand-paper
I suspect grit in the bag. I throw mine in a fabric satchel, along with a slew of other stuff, to take it back and forth from work. No damage has shown up yet.
I haven't seen any info on this case here on XDA yet, so i figured i'd put a quick review out there.
http://www.meritline.com/htc-evo-3d-new-aluminum-metal-hard-case-cover-silver---p-72656.aspx
They have a couple of different colors, black, silver (plain), blue, and pink.
http://www.meritline.com/newsearch.aspx?SearchTerm=evo+3d+aluminum
I found this case while browsing around on Meritline. I've bought a bunch of stuff from them in the past and everything has always been good quality so i figured i'd try this case. For 4 bucks i figured i couldn't go wrong, and in reality i couldn't be happier! The pictures on the meritline site can be deceiving. The main image of the case shows the "inside" on the left, and the "outside" on the right. The outside of the case is what the back of the phone looks like. There is a machined circle pattern on the backside. The inside of the case shows that it is aluminum all the way through, not just a thin plating on the plastic.
The case is a single piece "snap on" style case. The fit is great, really tight and clean. No issues I have seen over the past week or so of use. I purchased the silver colored on. The back of the case is aluminum, the plastic that clips around the phone looks to be molded to it. The case does not add much to the phones overall dimensions, but does add some weight (which i like). My brother picked up a SGSII and it feels like a cheap plastic phone. The 3VO is heavy, and this makes it feel like a brick **** house without making it feel too large (my biggest pet peeve of most cases).
I opted for the Expedited Ground shipping which was 1.99. Standard shipping is free.
Check it out!
Actually - that case was discussed in the larger evo 3D case thread. It looks great, and people liked the fit - but the concern was that the aluminum consistently reduced phone reception and data transfer speeds.
P0ll0L0c0 said:
Actually - that case was discussed in the larger evo 3D case thread. It looks great, and people liked the fit - but the concern was that the aluminum consistently reduced phone reception and data transfer speeds.
Click to expand...
Click to collapse
"My side's fine." No problems at all...
Nice, thanks for the review.
Sent from my PG86100 using xda premium
I bought one and my only complaint was the corners getting scraped every time I put it on or take it off. Thats all.
Sent from my PG86100 using xda premium
rudyrude432 said:
I bought one and my only complaint was the corners getting scraped every time I put it on or take it off. Thats all.
Sent from my PG86100 using xda premium
Click to expand...
Click to collapse
That would be my only complaint. The case is tough to remove.
i found that if you follow my little trick its easy to remove
1.get a credit or store card
2 with the phone on its back screen upwards slide the card between the case and the phones left hand side
3 with the card stuck in there hold the corners of the case amd the topmost black parts of the phone
4 pull!
5 case should move easily and seperate with card falling on floor
easy! no more scraped corners
also when putting it on put the side with the buttons in forst then just gently push the other side into place
Okay so I am sharing my experience for everyone. I had recently broken my screen, and I needed to replace the screen. I bought a screen digitizer off of eBay, and....Destroyed the phone sub frame. The reason I am posting is because I am warning all of you, you need to buy a full display assembly online. This includes the whole new display( glass and LCD) wires and bits, and a full subframe. Unless you are superior to an Asian 12 year old working in the factory that made your phone (hint hint, wink wink, you're not) than you need to buy a full assembly, or end up like me an destroy your phone.
Sent from my Amazon Kindle Fire HD using Tapatalk HD
+1.
Unfortunately, I saw this post after doing damage to my phone. The plastic housing that the digitizer /lcd sits in is verrrryyy easy to damage around the edges when you try to separate the screen. Heating it with the heat gun to get the separation actually makes it even more fragile and prone to damage. Thankfully I was able to return digitizer/lcd and get full setup from here :
http://www.etradesupply.com/oem-htc-evo-4g-lte-lcd-screen-and-digitizer-assembly-with-front-housing-and-light-guide.html
Hopefully things will go a little better this time.
Wow, that includes the plastic frame? I replaced my screen a couple of weeks ago (glass and LCD), and the edges of the frame did get slightly chewed up. It's not too bad, but I wish I had known abut this item.
On a positive note, I suppose I can get a job in China when the economy completely collapses.
Sent from my Nexus 7 using xda app-developers app
Ya my screen got waterlogged after I got trashed and left it out in the rain. Let everything dry out and thankfully all the boards and connectors work. I ended up going the cheap route and just buying a screen and not the frame. I almost successfully got the thing apart. I do have a small chip in the frame on the left side but my case covers that. I only paid around $50 but I did give myself around $50 in headaches. Definitely spend the extra $50 and just get the whole package.
If you do decide to try and separate the screen from the frame, use a lot of heat. Not necessarily high heat, but for a good duration. Get the adhesive nice and warm. Then pry it loose through one of the holes in the housing/frame (go at it from the back) and slowly work it away from the frame. Once you get it off, heat the adhesive back up and then add some 5 minute quick epoxy to the black adhesive pads in the frame. Then use some clamps and let the epoxy cure. There is a great video I followed below. It took me a while and I will probably ride with this for a minute until it bothers the hell out of me. My gf said she can't even notice.
https://www.youtube.com/watch?v=Ae52Ug8vFwA
case screen cover plastic sheet work?
I'm just wondering how many naked phones get broke compared to well protected?
Gnexd said:
I'm just wondering how many naked phones get broke compared to well protected?
Click to expand...
Click to collapse
I have a Incipio NGP case on mine all the time and I always have a screen protector installed (usually the cheap ones from Amazon). I have never had a problem with the screen until I left my phone out in the rain. The Gorilla Glass II is decently strong but only to a certain extent. I mainly use the screen protector from scratches if I accidentally put it in the same pocket as my keys.
I was afraid of breaking mine one day, fortunately for me my volume button went out first and I have Best Buys insurance and the replace the phone with no deductible.
Seems like screen issues are pretty common on this model. I'm on my 4th Evo now because the screen kept failing on me. Based on what I read it sounds like I'd never want to have to replace this myself.
hi as many note 3 users know, the plastic side frame is easy to get damaged, i have few cracks and one line just under the main power button (not sure just facial or completely crack?)
so, how easy is to change and which one i have to buy ? - im quite noob in hardware sides.
Sure you can buy one on Ebay
I have the same problem, the silver plastic bezel is very fragile.
If you search in Ebay you can found the Bezel and some of them come with tools to turn this in a complete DIY.
Actually i found all the body for this phone in ebay, so you can turn your used and damaged note 3 into a "brand new" one.
Thanks 4 the info. Where did you find it. Could you please share the link?
Thx in advance
hey guys.here is a link for the bezel replacement Bezel On EBAY
i want to tell you that it's not that easy to change it as you need to move the lcd screen from the one bezel to the other one.
there is glue between the lcd and the bezel so you need to warm it and remove it really carefully.i did the process yesterday on my note 3 and it was a pain in the a$$ so i have to tell you to be carefull before any move you re going to do.
Any link for Indian note 3?
Sent from my SM-N900 using XDA Free mobile app
I considered doing this, as I was given a note 3 a while back, but the bezel is beat to hell and the screen had a minor crack. I should've replaced both at the same time, but the small crack turned into a large one and needed immediate attention It's covered by a case now anyway though, so it's not much of an issue anymore.
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Its a tough job!!!
got my Note 3 as a gift from a friend who cracked it. I replaced the entire Display (along with frame)
and 3 days later I dropped it and got scratches in the frame.
so I decided to buy a frame and fix but its really a tough job.
so I got a bumper for 3$ and job done
I have installed one of those here http://www.ebay.com/itm/Thin-Aluminum-Metal-Bumper-Case-Cover-For-Samsung-Galaxy-Note-3-III-N9000-N9005/151251742076?_trksid=p2045573.c100033.m2042&_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D31478%26meid%3D341538ef5e9d4d6da3228a5f902e8cf1%26pid%3D100033%26rk%3D1%26rkt%3D4%26mehot%3Dpp%26sd%3D151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
thanks i thought i saw same one for bit less than that, will browse ebay later.
maskerwsk said:
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Click to expand...
Click to collapse
Photos plz
Up! I'm interested too.
yes i just remember i have some sand paper at home please post photo and detailed instructions... cheers
rockbastard said:
I have installed one of those here http://www.ebay.com/itm/Thin-Alumin...id=100033&rk=1&rkt=4&mehot=pp&sd=151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
Click to expand...
Click to collapse
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
triad88 said:
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
Click to expand...
Click to collapse
I haven't noticed any drop in reception at all
rockbastard said:
I haven't noticed any drop in reception at all
Click to expand...
Click to collapse
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Mr.Ultimate said:
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Click to expand...
Click to collapse
you have a lot of cases!
erwinsie said:
you have a lot of cases!
Click to expand...
Click to collapse
little too many ... beware that those wooden cases are the coolest thing your phone can get but if you do drop your phone they crack and break apart sometimes... not always though but alot alot sooner than any plastic case would and thats a heartbreaking thing because there not exactly cheap case, but hey - how often does someones phone feels and smells like real fresh quality piece of wood? I like them wooden ones very much even if they crack and put some tax on my pocket at the end of the day its almost like your personal signature of style ... besides, its always warm to touch and zero signal interference
PS: lots more were thrown out many months ago, especially all those metalized ones, no use to me nor could I offer them to anyone I knew who had note 3 due to what they are
When my display was damaged, it got repaired, not only the glass, but the whole display including the bezel, it was 1 piece.. I guess it's very hard to replace only the bezel