[Q] replacing the power button and micro usb port - Vibrant Q&A, Help & Troubleshooting

so i managed to mess up the flex cable connected to the power button AND ruin my micro USB port ( i accidentally broke the far left pin, and while trying to replace it drenched the rest in solder) ((internal pins, not external)) does anybody know how i could replace these or fix them without breaking the bank (teenager with no job >.>)
*in case anyone was wondering, i broke them doing this : http://youtu.be/0ga4N_Ih9GE
EDIT: i have an old blackberry with a microusb port somewhere if that could be useful somehow?
edit2: started to wick some of the solder off of the pins with my iron, i dont actually have a wick. unfortunately i have class in the morning and some papers to write so i wont be able to do much. looks like im going back to my old motorola cliq until i can figure this out. anyone have any advice for soldering extremely small connections so maybe i can redo the pins? i have an idea for the power button.

Related

[Q] HELP!!! broken black wire/connector inside HD2

Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse

[Q] How to install new usb port?

Well i ordered a new usb port because my old one is broken so i was wondering how to install a new one can anyone make a video to show mw how to
Here is how to disassemble. Taking out the the usb or any other solder joint in the phone requires a micro soldering tipped gun and installing you will need very thing solder
It is not hard to do just don't drink coffee before trying to solder the caffine shakes will make it impossible...... need very steady hands and a magnifying glass or glasses that are 3x or better
http://www.youtube.com/watch?v=gOvt6atrin8&feature
good luck.......
Not sure what to do so do remove all connected part to usb then take new one an place the pins on the usb an connect it to the motherboard an then it should work? an what tools do i need an phone is opened already

[Q] Anther x10i Charging Problem !!!!!!

I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
i have the same problem with my x10 but i have warranty but whilst i was waiting for them to collect it, i cut my usb lead up and stripped the black and red cables back obviously positive and negative and took the battery out and wedged each cable on the phone connector with the battery my battery had a plus and negative signs on it so was easy 2 work out, it charges the battery but it doesnt come up as charging on the phone it will still blind red lights but doesnt turn off, you have to keep and eye on the charging levels on the phone status do not let it go over 99% as this method dont tell the battery to stop charging, also this is not full proof and could break your x10 if not dont correctly,but as for your question the usb port does need to be soldered good luck
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
Hi John,
I fixed my friends USB port, you will need:
"helping hands" (a tool for holding small things with a magnifying glass)
0.5mm or 1mm Soldering iron
Hot glue
Under the magnifying glass, there you will see the 5 pins the usb port was solderded onto. You will need to put a little bit of solder onto each pin and onto the board.
Hold everything together with the helping hands, and just tick the soldering blobs with your iron. This will connect all the points. Do not solder for to long, or you will bridge pins or remove the solder.
Continue until all 5 is connected. Solder the 2 points on the side (holds the USB port, you could do this first if you don't have the helping hands)
plug in cable, use multimeter to see if there is current by you battery pins.
Voila.
If no power then you have to follow one of those fixes online where you have to bridge the doide and the V+ port.
Thanks for the info, like I said the phone is dead anyway, so I can't really make it any worse (That's what I keep telling myself anyway).
It the parts were a lot bigger, I probably wouldn't be bothered as much, but if I do get it wrong, I'm hoping I can take it off, remove the solder and just start again. (hopefully)
I think I have a good idea now of what I'm supposed to be doing, but I'll probably have to wait till I get a new soldering iron, as mine is a little bit too big.
Thanks ...John...

usb/charging port

has anyone gone through issues with their usb port? this is going to be my third time fixing it, if i even fix it at all. buying boards just for the usb is pretty frustrating since i usually havre to buy a complete phone for it. i actually have just the usb ports themselves but it didnt work out too well the first time. very small soldering. anyone else had theirs go bad more than once?
micro usb port fix
yes, it takes insane soldering skills to fix one. but instead of buying a phone just for the port you can get a replacement micro usb port on ebay for a few bucks. once you solder the new one on you can coat the pins on the board with a hot glue gun or any other solid adhesive for strength. once the job is done try to remember phone ports are delicate and should be handled with care and you wont have a problem again.

[Q] Captivate usb-mainboard problem

I have a captivate with bad usb port it was charging but can't get connected to the computer I opened it up and found out that there is a problem with the board the place where the usb port should be soldered (the pads) is gone.
I'm asking is there a way to put a wire connecting to some place on the board (the place where it should go)????
plzzzzz help me guys !!!!
Wow, that's fried.
I'm amazed that it even charges.
I think that I'd unsolder the connector and scrape all the burnt junk off, glue a new connector on the surface, then run wires to where they should go.
The D+ and D- should be somewhat easy to track down.
Those data lines usually run close together and they go to two "build-out" resistors before they go on to some chip.
Renate NST said:
Wow, that's fried.
I'm amazed that it even charges.
I think that I'd unsolder the connector and scrape all the burnt junk off, glue a new connector on the surface, then run wires to where they should go.
The D+ and D- should be somewhat easy to track down.
Those data lines usually run close together and they go to two "build-out" resistors before they go on to some chip.
Click to expand...
Click to collapse
thanxxx
I tried to track it down but I couldn't so I'm asking if there's any map or a scheme for the mainboard to help me!!!

Categories

Resources