Hi,
I want to put the MiniCM7-2.1.9 on my X10 Mini Pro. At the moment I have Froyobread v023f installed
Baseband: M76XX-TSNCJOLYM-53404015
Kernel: 2.6.29 [email protected] #1
Do I HAVE to flash a new kernel (nAa)?
Where can I see that my Bootloader is unlocked?
Greets
You do need that kernel, the rom won't work without it.
Have a look in the Development section for SE Tweaker, that'll tell you if your phone is unlocked.
Sent from my U20i using XDA App
If you never installed a custom kernel, your bootloader is locked so you need to unlock it before installing the kernel.
Latest MiniCM versions (from 2.1.0) need nAa's custom kernel to work so you have to install it or install a previous release of the ROM (I'd suggest 2.0.5)
use this to unlock your bootloader and flash a the nAa kernel - easy and quick
http://forum.xda-developers.com/showthread.php?t=986690
is it possible to flash the kernel after the rom? because I just did, and I got Sony Ericsson logo in screen.. can't install the kernel or go into recovery..
Super-Veloce said:
is it possible to flash the kernel after the rom? because I just did, and I got Sony Ericsson logo in screen.. can't install the kernel or go into recovery..
Click to expand...
Click to collapse
no you can and your doomed.
just joking. remember before installing a rom if the requirements says use this kernel then you should flash the kernel because it is required right? try going back to stock using pc companion or seus
Paddy3103 said:
Hi,
I want to put the MiniCM7-2.1.9 on my X10 Mini Pro. At the moment I have Froyobread v023f installed
Baseband: M76XX-TSNCJOLYM-53404015
Kernel: 2.6.29 [email protected] #1
Do I HAVE to flash a new kernel (nAa)?
Where can I see that my Bootloader is unlocked?
Greets
Click to expand...
Click to collapse
You can put only MiniCM7Pro
http://forum.xda-developers.com/showthread.php?t=1201116
Cordially,
Ra
Paddy3103 said:
Hi,
I want to put the MiniCM7-2.1.9 on my X10 Mini Pro. At the moment I have Froyobread v023f installed
Baseband: M76XX-TSNCJOLYM-53404015
Kernel: 2.6.29 [email protected] #1
Do I HAVE to flash a new kernel (nAa)?
Where can I see that my Bootloader is unlocked?
Greets
Click to expand...
Click to collapse
As far as I know, MiniCM7 works only with his nAa kernel, so your bootloader has to be unlocked. MiniCM Pro by paul-xxx uses stock kernel or custom kernels (nAa kernel with that rom will give a wifi error).
To check if you bootloader is unlocked. Use S1Tool and check the loader version. If it's a lower cased 'r' then it's unlocked, if not there are many tutorials around here to help you unlock your bootloader. Hope this helps.
@Paddy3103
Go to the official page (link below)
http://forum.xda-developers.com/showthread.php?t=1415026
It's got all the details that you'll need just make sure that you read every single line thoroughly.
If you make any mistakes than you can use sony ericsson update service to reset it back to the stock SE rom.
Btw I recommend that you use the flash tool to unlock bootloader and to check if its unlocked as Noobonic said use the SE1Tool.
For me I'd say that MiniCM7 is the best custom rom that exists right now but since we have to flash the nAa kernel it seems kind of risky at first but if you understand the steps and follow it properly than there's not much to worry about.
The other ROM's are also quite good but the MiniCM7 is the best and most stable custom ROM.
Related
what is the way to upgrade from MiniCM7-2.1.3 to MiniCM7-2.1.6 (and thus from kernel nAa-03 (or whatever number was when 2.1.3 was released) to nAa-07)?
Do I just follow the normal procedure as if I had original SE rom?
thanks
1.Do a backup using CWM recovery.(this is just for safe, if smth goes wrong)
2.Download miniCM7 2.1.6 and put it into your root folder on SDcard.
3.Flash the latest nAa-07 kernel.
4.Boot into recovery, and flash the rom.
P.S. You don't have to do full wipe/factory reset.
thanks man.
I have to upgrade 2 x10minis and one x8. I suppose the procedure for all 3 is the same?
- x10mini 1: has MiniCM7-2.1.3 with nAa as explained above, you replied for this one.
- x10mini 2: has an older MiniCM7-2.0.x, at that time there was no nAa kernel. So it has original kernel
- x8: this one has older version of GingerDX with original kernel too.
Is the procedure the same for 2 and 3, but first I have to unlock bootloader I understand?
First backup everything from cwm or x10 recovery
now, if u didn't unlock the bootloader do it. Nice tutorial here
then u need a few tools like flashtool and nAa kernel. Flash it using flas tool.
all u need to do is click and click. I got it on my first attempt
Next get the Rom u want it and from CWM flash it. Good luck !
vadexlux said:
thanks man.
I have to upgrade 2 x10minis and one x8. I suppose the procedure for all 3 is the same?
- x10mini 1: has MiniCM7-2.1.3 with nAa as explained above, you replied for this one.
- x10mini 2: has an older MiniCM7-2.0.x, at that time there was no nAa kernel. So it has original kernel
- x8: this one has older version of GingerDX with original kernel too.
Is the procedure the same for 2 and 3, but first I have to unlock bootloader I understand?
Click to expand...
Click to collapse
If you unlocked bootloader while installing miniCM7, you don't have to unlock it twice. This depends on what rom you are goning to install. Also if you want to flash kernel, you have to unlock bootldr.
Hi guys
After unlocking bootloader on my SE Xperia X10 Mini, I flashed nAa-08 kernel and then MiniCM7-2.1.6. During the installation, however, I noticed that the ROM requires nAa-07 kernel, while I flashed nAa-08. All was still fine, but I would like to know if there are any known problems or if I have to flash nAa-07 kernel
TY
Greetings from Italy
sith.warrior said:
Hi guys
After unlocking bootloader on my SE Xperia X10 Mini, I flashed nAa-08 kernel and then MiniCM7-2.1.6. During the installation, however, I noticed that the ROM requires nAa-07 kernel, while I flashed nAa-08. All was still fine, but I would like to know if there are any known problems or if I have to flash nAa-07 kernel
TY
Greetings from Italy
Click to expand...
Click to collapse
it should not have major problems but it would be much safer and faster if you used the same rom kernel with the latest MiniCM7-2.1.7.i bet you it wont let you down.
I used the latest nAa kernel with his latest MiniCM7-2.1.7 and its just off the hook(VERY FAST AND STABLE)- PERFECT !!!
go here -> http://forum.xda-developers.com/show....php?t=1068553
SENT FROM x10mini pro running nAa MiniCM7-2.1.7
REMEMBER TO HIT THE THANKS BUTTON IF THIS HELPED YOU !!
I could try, but i have X10 Mini, not Pro. Probably a new porting for X10 Mini will arrive in few days
I hope so, at least
Would it be better to reflash nAa-07 kernel for now?
Naa forget to update the updater script, use always the last kernel!
Enviado desde mi E10a.
ChavitoArg said:
Naa forget to update the updater script, use always the last kernel!
Click to expand...
Click to collapse
I think so, too
TY to everybody
The MiniCM installation guide states to flash the latest nAa kernel.
Newer kernels are usually better than older ones.
I doubt nAa would remove features with new kernel versions.
santaranger said:
The MiniCM installation guide states to flash the latest nAa kernel
Click to expand...
Click to collapse
Exactly. I followed the instructions, but CMW Recovery was unable to find the nAa-07 kernel and suggest me to flash it. That's all.
Newer kernels are usually better than older ones.
I doubt nAa would remove features with new kernel versions.
Click to expand...
Click to collapse
It's my first time that I try flashing. Moreover, I have SE X10 Mini for less than a month. I wanted to be sure I have done everything right
sith.warrior said:
Exactly. I followed the instructions, but CMW Recovery was unable to find the nAa-07 kernel and suggest me to flash it. That's all.
It's my first time that I try flashing. Moreover, I have SE X10 Mini for less than a month. I wanted to be sure I have done everything right
Click to expand...
Click to collapse
First of all make sure you have downloaded evrything you need to begin the flashing.
{s1tool, msm7227,LATEST nAa kernel for x10 mini-NOT PRO,LATEST nAa MINICM7,Gapps-gb} THEY ARE ALL LISTED IN THE GUIDE.
1.Bootloader unlock is the forst step but you have to check that your phone can be safely bootloader unlocked. PLEASE HAVE A GOOD READ THROUGH THE GUIDE SO THAT YOU ARE SURE http://forum.xda-developers.com/showthread.php?t=1254225
rember to hit the thanks button if i helped you.
popcaan said:
First of all make sure you have downloaded evrything you need to begin the flashing.
{s1tool, msm7227,LATEST nAa kernel for x10 mini-NOT PRO,LATEST nAa MINICM7,Gapps-gb} THEY ARE ALL LISTED IN THE GUIDE.
1.Bootloader unlock is the forst step but you have to check that your phone can be safely bootloader unlocked. PLEASE HAVE A GOOD READ THROUGH THE GUIDE SO THAT YOU ARE SURE http://forum.xda-developers.com/showthread.php?t=1254225
rember to hit the thanks button if i helped you.
Click to expand...
Click to collapse
Yeah Thanks, all went well. Bootloader was unlocked, nAa-08 kernel was installed. MiniCM7, too.
I wanna just saying that (maybe) there is a minor bug in CWM Recovery. In fact, it doesn't recognise nAa-08 kernel.
Not so worrying...Please, try to understand me, i'm just a n00b
sith.warrior said:
Yeah Thanks, all went well. Bootloader was unlocked, nAa-08 kernel was installed. MiniCM7, too.
I wanna just saying that (maybe) there is a minor bug in CWM Recovery. In fact, it doesn't recognise nAa-08 kernel.
Not so worrying...Please, try to understand me, i'm just a n00b
Click to expand...
Click to collapse
Hi did you manage to install and get everything working ??
Before rebooting into CWM you should have the ROM you want to install+THE GAPPS TOO.
HI evryone,
I am just a beginner using android for few months... My device is Xperia X10 Mini pro U20i..
I tried to upgrade to MIniCM9 3.0.1 from CM7 (CM7 was working wel, i just wanted to upgrade)..
I downloaded MiniCM9-3.0.1 [5/5/12]ICS 4.0.4/CM9 from http://forum.xda-developers.com/showthread.php?t=1636501
I wiped cache, user data and dalvik cache n tried to install CM9 rom.. It installed successfully, but I received a warning message. 'Should have kernel flashed to atleast ics-nAa 01' like dat...
But when i rebooted, it didnt go beyond d Sony Ericsson logo.. I went back to stock 2.1 using SEUS..
Then I rooted mobile using SuperOneClick 1.6.5 n rooted successfully. But wen i flashed the kernel 'U20_nAa-ics_01_2.6.29.6-nAa-ics-01.ftf' or 'U20_nAa-ics_01_2.6.29.6-nAa-ics-02.ftf' from http://forum.xda-developers.com/showthread.php?t=1636504, it couldnt flash.. I get an error ERROR - ERR_SEVERITY="MAJOR";ERR_CLASS="SECURITY_CLASS";ERR_DYNAMIC="SIN header verification failed"..
I tried flashing with flashtool 0.2.9.1 and with flashtool 0.7.1.0 but i couldnt get it done..
Can anyone help me with dis? Why do i receive dat error message? How can I upgrade to CM9??
While upgrading to CM7, I never flashed my device. I just rooted it, installed xrecovery n cleared factory data, disk cache, dalvik cache n installed d rom... So, is there any similar way to install CM9 also without using flashtool?
Thanks..
You need a custom kernel for MiniCM9, and the reason you can not flash this kernel is because your bootloader is locked. In the kernel thread there is a link to the tutorial on unlocking your bootloader, but please be careful, it doesn't work for everyone
Thanks for dat...
Is there a way we can install CM9 on U20i without unlocking bootloader?
Also, plz tell, does SEUS work after unlocking bootloader?
No you can't install MiniCM9 on anything other than the nAa-ICS kernel, and for that you need an unlocked bootloader
Yes, seus or pc companion will still work with an unlocked bootloader. the worst that can happen when unlocking the bootloader is that you will lose the ability to use your phone as a phone (disabled radio-capabilities). Check if it still works before flashing a kernel and custom rom, if it doesn't relock the bootloader and stay on stock kernel.
How to relock Bootloader? Link for U20i Stock Kernel..
Oh. Thanks a lot..
How to relock bootloader? I saw in a forum somewhere that there s no way to relock bootloader..
Also I tried to download the stock kernel for U20i from this page: http://forum.xda-developers.com/showthread.php?t=1254225... They have given the link for downloading the stock kernel as http://db.tt/ukt80PBn
But the link doesnt work. I have searched many times but could neither open it nor find alternative link.. Can u plz tell any alternative link for it?
Thanks so much for ur responses..
First of all, you can relock your bootloader using S1Tool (by pressing the restore button), but if it is succesfully unlocked there is no need to relock it at all, unless you need to take it back to the shop for repairs under warranty.
(I can't remember where i got the latest version of S1tool from, i'll search for it later if you need it)
as far as the stock kernel is concerned, just do a repair with pc companion or maybe seus, i usually use pc companion. it won't relock your bootloader but will install a fresh stock kernel and rom. After that you can root, install recovery or cwm whatever you used and restore the backup you hopefully made of your MiniCM7 rom.
Mind you: At this moment Minicm9 is not an upgrade yet in the sense that it will make your phone work better or easier, it's still very early in development and not that easy to get working well, if you need your phone on a day-to-day basis, stick with MiniCM7 for now.
Thanks a lot for that info..
I hav no complaints wid CM7. I just wanted to upgrade to ICS since it is out there.
I'll try unlocking bootloader n cm9. I'll go back to cm7 if it doesnt work or if it isnt suited for day-to-day operations..
Thanks so mch for ur help.. I ve understood a lot.. Thanx again.. :-D
If u find d link for S1tool, kindly post it..
Sent from my U20i using XDA
S1Tool with Restore button
Good luck, i hope everything works fine for you
I unlocked d bootloader, flashed n installed d MiniCM9 rom...
It works fine.. ICS is awesome..
Thank u 4 all ur help
Happy days then Have fun...
x10 mini pro 2.1 to Gingerbread (MiniCM7)
sjoedanny said:
I unlocked d bootloader, flashed n installed d MiniCM9 rom...
It works fine.. ICS is awesome..
Thank u 4 all ur help
Click to expand...
Click to collapse
hi
I was checking xda forum for upgrading my x10 mini pro to gingerbread version and I am really confused with the whole process. At present I rooted my phone with superone click and confused with next steps. do i need to unlock bootloader ? do i need to flash with Naa kernel ? Some guides instructing to install minicm7 without unlock bootloader and kernel flash.which correct or good ? I dont know what to do and I dont want to brick my phone too. Please help me and thank you very much for ur time
shane64 said:
hi
I was checking xda forum for upgrading my x10 mini pro to gingerbread version and I am really confused with the whole process. At present I rooted my phone with superone click and confused with next steps. do i need to unlock bootloader ? do i need to flash with Naa kernel ? Some guides instructing to install minicm7 without unlock bootloader and kernel flash.which correct or good ? I dont know what to do and I dont want to brick my phone too. Please help me and thank you very much for ur time
Click to expand...
Click to collapse
If you want to run MiniCM7, by nAa, you need to unlock your bootloader and flash the nAa GB kernel (currently at version 13).
If you want to run MiniCM7Pro, you can run it without a custom kernel and without unlocking your bootloader.
They are two different ROMS with almost the same name, i can understand why that can be a bit confusing
MiniCM7Pro
Thank you very much SmG67, for your fast and valuable reply. Am a newbie here and I am trying to learn the things.Your information is really cleared my fear about bricking. I have few doubts to share with you sir,
What is the main difference between minicm7 and minicm7pro ?
If I opt minicm7pro now, then Can I upgrade or install minicm9 later ?
Minicm7pro by Bpaul is not giving any instruction for how to install it. So where can I get the instructions
SmG67 said:
If you want to run MiniCM7, by nAa, you need to unlock your bootloader and flash the nAa GB kernel (currently at version 13).
If you want to run MiniCM7Pro, you can run it without a custom kernel and without unlocking your bootloader.
They are two different ROMS with almost the same name, i can understand why that can be a bit confusing
Click to expand...
Click to collapse
shane64 said:
Thank you very much SmG67, for your fast and valuable reply. Am a newbie here and I am trying to learn the things.Your information is really cleared my fear about bricking. I have few doubts to share with you sir,
What is the main difference between minicm7 and minicm7pro ?
If I opt minicm7pro now, then Can I upgrade or install minicm9 later ?
Minicm7pro by Bpaul is giving any instruction for how to install it. So where can I get the instructions
Click to expand...
Click to collapse
Minicm7Pro was a port to the x10mini-pro from early MiniCM7 for the x10-mini, but it got updated to the latest Gingerbread, while still working with the stock kernel, minicm7 was released later and moved to the nAa-custom kernel, which gave it some performance benefits.
If you can unlock your bootloader, you can flash any kernel and rom you like that is available for your phone, but MiniCM7Pro or ArcMini Nxt (which runs on just about any kernel) are good places to start anyway.
for installing MiniCM7Pro you need:
2.1.1.A.0.6 firmware with *4015 baseband (check Settings - About Phone, the baseband should end in 4015)
Rooted phone
ClockWorkMod Recovery
Copy the MiniCM7Pro zip to your sd-card
Boot into CWM (press back-button on the kernel-logo)
Do a backup
Install the ROM
Wipe factory-data/reset
Wipe Cache
Wipe Dalvik-Cache (in CWM advanced)
Wipe Batttery Stats (in CWM advanced)
Reboot and enjoy
MiniCM7Pro
Thank you very much, and I am now looking into how to install it on my device.Because minicm7pro thread is not giving any step by step instruction to install it. I am really appreciating your help. Good day
@ SmG67
Thank you very much for your advice's and I upgraded my x10 mini pro to android 2.3.7 ( cm7 pro) . I really appreciating your help on this regard. I was out of station for a while,and that's the reason for this late reply.My phone is working without any problem except wifi hotspot, It will show turning on and continue that status without actually turning it on when I am trying to enable it.Although its not a big headache or function for me.so its okay.Once agin thanks.Good day
MiniCM 7 pro to ICS
@ SmG67
hi... My x10 mini pro running on Minicm7 pro by paul and stock kernel.I installed it according to your advice and I appreciating your helping words. Now I would like to move to ICS rom and nAa kernel. I have few doubts regarding installation.
1. Do I need to go back to old 2.1 factory ROM before flashing ics and ics nAa kernel ?
2. If yes, How can I install old SE rom ?
3. Can I install MiniCm9 over JB nAa kernel ? because it will reduce my job when am moving to ics to JB rom
Thx
shane64 said:
@ SmG67
Thank you very much for your advice's and I upgraded my x10 mini pro to android 2.3.7 ( cm7 pro) . I really appreciating your help on this regard. I was out of station for a while,and that's the reason for this late reply.My phone is working without any problem except wifi hotspot, It will show turning on and continue that status without actually turning it on when I am trying to enable it.Although its not a big headache or function for me.so its okay.Once agin thanks.Good day
Click to expand...
Click to collapse
shane64 said:
@ SmG67
hi... My x10 mini pro running on Minicm7 pro by paul and stock kernel.I installed it according to your advice and I appreciating your helping words. Now I would like to move to ICS rom and nAa kernel. I have few doubts regarding installation.
1. Do I need to go back to old 2.1 factory ROM before flashing ics and ics nAa kernel ?
2. If yes, How can I install old SE rom ?
3. Can I install MiniCm9 over JB nAa kernel ? because it will reduce my job when am moving to ics to JB rom
Thx
Click to expand...
Click to collapse
1. No
2. 1 was a no, so no need for that
3. No, it won't work.
For 2011 devices line, be sure you are not in MTP mode
Thank you SmG67....I checked my device with s1tool and found " SEMC SIMLOCK CERTFICATE " then forwarded to flash tool. But I faced an issue and my flashing halted. When I am connecting my phone it will detect and showing INFO : For 2011 devices line, be sure you are not in MTP mode ....then going to charging mode....Dont know whats the reason ? :crying:
For your info : I installed all x10,x8,x10 mini pro ADB drivers, fastboot drivers, Flashmode drivers etc. USB debugging is ON, unknown sources is enable......my flashtool version was 0.6.8.0 .
SmG67 said:
1. No
2. 1 was a no, so no need for that
3. No, it won't work.
Click to expand...
Click to collapse
shane64 said:
Thank you SmG67....I checked my device with s1tool and found " SEMC SIMLOCK CERTFICATE " then forwarded to flash tool. But I faced an issue and my flashing halted. When I am connecting my phone it will detect and showing INFO : For 2011 devices line, be sure you are not in MTP mode ....then going to charging mode....Dont know whats the reason ? :crying:
For your info : I installed all x10,x8,x10 mini pro ADB drivers, fastboot drivers, Flashmode drivers etc. USB debugging is ON, unknown sources is enable......my flashtool version was 0.6.8.0 .
Click to expand...
Click to collapse
Our phone is 2010 device so don't worry about the mtp mode thingy
Your lfashing halted because you didn't unlock your bootloader yet.
Connect your phone to flashtool
Choose Únlock bootloader' in the plugins menu
Follow Instructions
Flash the kernel
You should be fine
I have SE stock rom 2.1 update 1 with stock kernel on my x10i mini. I have rooted my device and I want to know if I can enable multitouch on my phone. Please someone help me .
Thanks in advance...
I didnt try only kernel,but I try custom MINICM7-2.2.0 based on GB 2.3.7 and it is like new phone reBORN, fast&stable.
Sort off, yes
Check this
For stock kernel
The links are dead.. Downloading of x8gesture.ko not working.
SmG67 said:
Sort off, yes
Check this
For stock kernel
Click to expand...
Click to collapse
downloading not working of x8gesture.ko
In that case, there are a few froyo-based roms (srom-froyo, froyobread) that include this particular module, don't know if those links are still working, try to search the x10mini development forum to find them
SmG67 said:
In that case, there are a few froyo-based roms (srom-froyo, froyobread) that include this particular module, don't know if those links are still working, try to search the x10mini development forum to find them
Click to expand...
Click to collapse
Do they require unlocking of bootloader .Actually I am afraid of this purpose.Is there any GB rom that can be flashed without unlocking bootloader on stock kernel 2.6.29 Thanks for Help.
You only need to unlock your bootloader if you need a custom kernel.
All the froyo roms run on the stock kernel, so they can be installed without unlocking the bootloader.
GB roms all run on a custom kernel (on the x10Mini), so you need to unlock the bootloader for that.
If you get S1Tool and post the output, i could probably provide you with some guidance on the safety of unlocking
SmG67 said:
You only need to unlock your bootloader if you need a custom kernel.
All the froyo roms run on the stock kernel, so they can be installed without unlocking the bootloader.
GB roms all run on a custom kernel (on the x10Mini), so you need to unlock the bootloader for that.
If you get S1Tool and post the output, i could probably provide you with some guidance on the safety of unlocking
Click to expand...
Click to collapse
Yeah !! in the output It shows SEMC something with capital R . Actually date is 10w29. Flashtool is big file and I have a slow connection... Smthng else for unlocking bootloader
it should say semc-simlock certificate, and 10w29 is ok too. you can get the manual scripts for unlocking the bootloader in a slightly smaller package, but the point about unlocking the bootloader is to install a custom kernel... you will need flashtool for that... lol.
I would say, try one of the froyo roms if they're still available, i'm pretty sure froyobread with the hotfix can be downloaded and they can be installed on the stock kernel. but then, those are big downloads too on a slow connection
SmG67 said:
it should say semc-simlock certificate, and 10w29 is ok too. you can get the manual scripts for unlocking the bootloader in a slightly smaller package, but the point about unlocking the bootloader is to install a custom kernel... you will need flashtool for that... lol.
I would say, try one of the froyo roms if they're still available, i'm pretty sure froyobread with the hotfix can be downloaded and they can be installed on the stock kernel. but then, those are big downloads too on a slow connection
Click to expand...
Click to collapse
Ok I am starting... Given 30 minutes to my wintage phone,
Thanks for paying attantion..
yupp its done ..XDA rocks B-)
You're welcome
Array. I've unlocked the bootloader and I have xrecovery on my phone. I also have put GB miniCM rom as update.zip on SD card
Now the problem is on GB thread it said that I should have naA kernel on my phone and on naA kernel thread it said that I should have GB custom rom. I have only unlocked the bootloader and still on stock rom and stock kernel.,
once again its ur turn to sort me out of this problem...
:-D
First you flash the nAa kernel using flashtool
Then flash the rom through cwm
Sent from my E10i using xda premium
Bro I have gone one step ahead and have installed cloclwordmod .. now I am flashing the naA kernel... But what after flashing the kernel if I start my phone do I have to first enter in CWM and flash new minicm7 rom or I can use this kernel on my stock rom 2.1
Go into CWM and install MiniCM, stock will not boot on the nAa kernel.
SmG67 said:
Go into CWM and install MiniCM, stock will not boot on the nAa kernel.
Click to expand...
Click to collapse
Done ;-)
How do I check the requirements?
-Latest 2.1.1.A.0.6/2.1.1.C.0.0 SE firmware / Baseband: M76XX-TSNCJOLYM-53404015
- Unlocked bootloader
- Latest version of the ICS nAa kernel
Thanks
mike4444 said:
How do I check the requirements?
-Latest 2.1.1.A.0.6/2.1.1.C.0.0 SE firmware / Baseband: M76XX-TSNCJOLYM-53404015
- Unlocked bootloader
- Latest version of the ICS nAa kernel
Thanks
Click to expand...
Click to collapse
for the first one: check settings - about phone, it will list the installed firmware version and baseband
for the second one: no phone comes with a bootloader unlocked, so if you haven't unlocked it yourself, that requires action on your part
for the third one: if the second one isn't done, you don't have the third one, you will have to flash that yourself after you've unlocked the bootloader
1. Its not an update, its a custom rom.
2. Baseband can be found under About Phone
If you don't know how to unlock boot loader and what NaA kernel is I highly suggest you read up a lot more before doing anything
If you dont chances are you'll get your phone screwed up.
There's a good guide in the X8 development section on unlocking bootloader by SpyderX.
Sent from my E10i using xda app-developers app