Related
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Appologize for posting the thread twice... I wasn't sure if this goes to the Hermes or the Herald forum...
Hello All,
I recently got an ATT 8525 and I'm trying to use it with my T-Mobile (US) SIM. I was able to successfully unlock the SIM and CID with an util/rom I found on this site (I think the post was from Pof). And I also re-flashed the phone with the latest ROM available.
But after about 5-10mins of usage the signal dies and when I reboot it says No GSM. Looks like the Radio ROM gets corrupted. I tried just re-flashing the Radio ROM and that doesn't help either. It works for short while and again the signal dies.
And also, I'm unable to install any of the generic ROMs (Fantastic Mobiz, PVET 40005) Although I'm connected to Active Sync when I run the Step 1 (ROMUpdateUtility_NV_G3.exe), I get a ERROR [222] : DEVICE NOT RESPONDING. And when I run the step 2 directly (update_rom.bat) I get an cannot update itsutils.dll maybe in use error.
As you can tell I've been messing with phone a lot for a couple of days with no luck and my frustration level is kinda high
As of now here’s where I stand. I re-flashed the phone (Image: 3.62, Radio 1.50) and it’s on the “Tap the screen to set up your windows based mobile device” screen. I plan on leaving it on this screen until I can a good solution.
I would like to get rid of the ATT ROM and install one of those hybrid generic ROM that is not Carrier specific. Any help will be much appreciated. Share your ideas, I’m very experimental
Phone Details…
ATT 8525
HERM100
IPL: 1.04
SPL: 1.40.0 lipro
ok ur going all over the map here.. did u hardspl first? also pvet 40005 isnt a hermes rom.. um try hardspl first THEN flash to a new rom maybe once you successfully do that then try a new 3.62 rom.. i run austinsync buts its naked..just like i like my women. ha. but if ur looking for a full blown try fun_key's rom or blinkys.. these arent carrier dependent
hey man jakeypoo, Thanks for your reply. I kinda figured that I was all over the map.
Okay first appologize my ignorance. What is a HardSPL? I did a search on this forum and I found Hard-SPL-V7.zip. Is this a good version to use? Also when I run the exe, All options are grayed out except for "Force Using SSPL" and "Is it Hard-SPL". What do I select.
Thanks!
Hardspl v7 is the latest version out there, its the one for you to use so that you're safe from future mishaps.
I also have an 8525 on T-mobile... so no worries.
Hope this helps.
http://wiki.xda-developers.com/index.php?pagename=Hermes_HardSPL
still problems (no gsm)
Thanks whistler4ever. That link was really a great help.
Here's what I did...
1. Installed the Hard SPL version 6
2. Installed the latest ATT ROM (ver 3.62 radio: 1.54) I had to do this because the radio on the phone was corrupt (says "no GSM" on the start screen) and couldn't install just the radio rom. kept giving connection errors.
3. Installed Schap's WM6 Pro 3.57 hoping this would get ride of the ATT ROM and my intial problem (no GSM) will go away.
Everything was fine for like 15 mins, then my phone just froze. I reboot the phone and sure enough the radio ROM was gone (no gsm). ;(
Running out of ideas.
1. Could this problem be because I'm using a TMobile SIM on a ATT's radio ROM?
2. Is the radio ROM specific to the phone type and provider(ATT, TMO..)? Is there a generic WM 6 radio rom? If yes, where can I find the latest version?
3. Any bright ideas?
Thanks again!
Current phone details...
ATT 8525
HERM100
IPL: 1.04
SPL: 2.10
ROM 3.62
Radio: no gsm
I was able to flash just the radio ROM - version 1.51. But again after a few hours the Radio got currupted. I also tried to follow the instruction ( http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5 ) to use the mtty.exe utility, but I don't get a USB prompt. I get Cmd prompt and if I still enter the password, it says invalid password. please help!!!
And how do I do the USB monitor capture? I could post more details that way. I'm using my girl friend's old razr now and it's painful!
I have used my t-mobile sim on AT&T rom's and other roms with no problem. I would try going back to a factory rom and then changing back to a cooked rom just to confirm its all a clean install. also, try downgrading your radio to a 1.47 or 1.48 (those have been proved pretty reliable across many cell providers).
Thanks Whistler. I'm going to start with the 1.48 version and if that doesn't work I'll try the 1.47 version. Not giving up on this.
I found 1.47 to work very well with t-mobile even when traveling...
Thanks Galaxys. I just installed the 1.47 radio. I have fully signal and the 'E', but I can't receive or make calls.
It almost looks like my TMO SIM is not compatible with the 8525. It always works for the first few minutes after an install and then stops working.
I'm very certain the phone is in good condition.
Should I try an older radio version.. like a 1.24 or something ?
Can I install just the tmobile radio rom?
I'm also going to install TNT 2.0 pro so I have the exact same set up as you and see if that makes a difference.
no luck!!!
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
try the way i posted in this thread http://forum.xda-developers.com/showthread.php?t=337125
ajjus said:
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
Click to expand...
Click to collapse
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Try to flash the entire UK T-Mobile ROM, then remove the internet settings and install the correct CAB for T-Mobile.
UK ROM here: http://forum.xda-developers.com/showthread.php?t=337163
PROVIDER SETTINGS CAB: http://forum.xda-developers.com/showthread.php?t=311446
a-h-t1, Junner2003 and galaxys - I'll try all your suggestions.
a-h-t1 - The first 2 steps went through fine. While I install the radio ROM as part of step 3, the installation doesn't go past 0%
I'm going try Junner2003 idea now. I'll keep everyone posted on my progress.
install stops at 11%
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
galaxys said:
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Click to expand...
Click to collapse
Hi Galaxys,
I don't think the IMEI is blocked. Or maybe it is, how do I find out? I don't have any of the symptons listed on the link you sent (don't hear the beeps or anything).
I originally had a T-Mobile wing. The LCD screen cracked (don't know how). And ofcourse TMo won't replace it.
http://forum.xda-developers.com/showthread.php?t=335346
I got 8525 from my company. It's almost new. Only used for a day on an AT&T SIM. This phone is free, and so I really don't have much to lose... so all out experimenting
Tried insalling from the micro card, even that stops while installing GSM. pissed!!! Why would the darn Radio not update???
this may sound stupid but if all else fails, why not...
my mda use to have signal then it would just disappear as well after 15 min or less..
turns out the sim card wasnt pressed in properly.. so i just put a piece of paper on top of the sim card to make it thicker and get the battery to press it down harder. and it solved all my problems...
just a suggestion..good luck
ajjus said:
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
Click to expand...
Click to collapse
See this post here for a possible reason (and technical explanation/theory) for your device stalling during radio update. The fix suggestions at the bottom of the page may help you - in particular :
Try cooling the device down a bit before flashing as the PIC chip (where your radio ROM is held) may flash more reliably/easier when cool. Don't ask why - that's from it's datasheet ;-)
The paper on the SIM card is a good idea too to rule out dodgy SIM connection - Great idea r0mmel
Dear Members,
I tried to upgrade my JasJam with "838Pro_HK_ENG_WM6_Upgrade_20070712"
Which worked with other JasJams (Many of my friends has it working).
On upgrading, it stucked on 11% saying Error [262]
I went through recovery, and it said remove the USB cable, remove the Battry, Return it, start the phone, connect the USB, and its recovered.
After that Its again stucked in 100% and the same senario is happening.
Please tell me is there any possibility to restore my phone working.
Its stuck now, and only the (Three color screen) is on the screen.
Hard reset, soft reset is not functioning, and the phone refused to show anything except the three color screen.
I searched the forum, but found no relative article, I am searching since two days your forum and I know that no other forums can help me in this as I was always getting my help from yours.
Thanks for your time.
HERM100
IPL-1.04
HERM100
SPL-1. 40. 0lopro
If you're using XP then untick "Allow USB Connection" in activesync.
Reset to bootloader on your Hermes, Hold power, OK button above flywheel and reset with stylus.You will get the same screen you have now but it won't be a f*&%ed up version of bootloader. Connect to PC by USB and Install Hard SPL V7, found here - http://forum.xda-developers.com/showthread.php?t=296722
After this, use the sd card method to install the ROM.
1. Format a 2Gb or less sd card FAT32. ?CFopy the .nbh file of the rom you want to it and rename to hermimg.nbh .
2. Insert into phone and reset to bootloader.
3 If you did everything right then follow the prompts...
Cheers...
Again problem!
Dear ultramag69,
Thank you for your fast reply.
I did (untick) that option in the ActiveSync.
And also did reset to the device by holding the Power + Ok (under the flywheel) with Stylus reset.
After that I downloaded "Hard SPL V7" and tried to update.
First of all, in the "Hard SPL V7" there was only the last option active, and there was down a checkbox also active, but when choosing the last option, checkbox bocomes like everything else disabled.
However, I got the erro 286
I felt like the Device disconnected from USB and reconnected again (Windows gave me the sound when you remove some USB device and you re-connect it again) :-|
I don't know what to do with this dead device now !
Thank you very very much for your time and help
Don't quote me on this as I suspect you need Hard SPL V7 but, as yo've tried things out and you're about to quit anyway, Try using the sd card to update the Stock rom, the rom that came on your Hermes, or updated version. It might let you do it if the CID matches.
I don't believe SPL 1.40 allowed you to flash ANY rom but it may let you re-install the stock rom BUT it must be the original carrier software it came with. If you had Telstra rom on it when you got it, it must be a telstra rom you flash. Make sure its for the right country too as some carriers are all over the world.
Cheers...
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
If you can, try to find the original SHIPPED STOCK ROM. It may be your Hermes won't be recoverable as the flash stopped in the radio rom part. Most people use a cooked rom as this has the radio rom part out.
I personally use the sd card method to flash my roms so there are no sync errors or accidents with my PC. But you need Hard SPL V7 installed to get that to work with any but the shipped rom.
DON'T try flashing anything but the shipped rom or you will loose all chances of recovering your Hermes.
The only other suggestion would be to flash the SHIPPED RADIO ROM, but you need to know what radio it was before you flashed it with the dopod rom.
Unfortunately the radio rom is the Achilles heel of our phone series. Any problems during flashing of that means we pretty much end up with a brick 99% of the time. Most people are stuck and the rest seem to have limited success reflashing the radio. AVERY small percentage get it working with no trouble, but its a REALLY small amount of people.
Good luck, Make sure you flash with the SHIPPED STOCK ROM to improve your chances of success.
Cheers...
Ultramag69, Thanks alot for your consideration.
Flusching using SD card didn't success with SPL V7.
I formatted my MicroSD card, 2GB with Fat32 FS.
After that I copied the file that came with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate, and holded the (Power + OK under flyweel) then restarted using the stylus, It showed me the tri-color screen, then it shows (Loading...) with Gray background screen (Which is normally the flusching screen) but it returned to the tri-color screen.
Any suggestions to get this SPL V7 installed successfully ?
I tried with all my (.nbh) files that I have downloaded from all sources, but its the same screen.
I think something is really wrong with me i-mate, should I take it to some Hard-ware service center ? and what can be damaged and need to be replaced in such cases ?
I am very excited in getting it working again.
Thanks alot.
Cheers...
I had bricked my Hermes a couple o' times, because of a rom I cooked half-way ( LOL ). Each time I had to flash back to the stock rom as suggested. Don't lose hope, cuz there's some people who will tell you just to accept it as bricked. You could also take the sucker apart and use jtags to flash. Most types of bricks can be solved when it comes to the Hermes. There's a thread somewhere that polled the different types of bricks, and except for radio bricks, most can be solved. If you unbrick it try 6.5 .... !!! My rom is cooked all the way now
Arwany, did you run the SSPL.exe file in the sd card instructions for Hard SPL found on page 116, post 1160 of the Hard SPL thread? You need a version of Soft SPL (SSPL) to flash using the sd card as the CID must be bypassed. The reason we Hard SPL our Hermes is because its safer. Its worthwhile flashing the SPL using unsafe SSPL (even if you use the pc you have Soft SPL installed) as its a short flash, flashing a rom (especially stock roms with the radio rom inside) is a riskier and longer flash.
Cheers...
I had the same problem.. All you have to do is establish a connection with Actisync, then run the Updater. There will be 3 colors on your Screen, sont worry, just wait 10-15 min and your should be done with the setup.
Want to help
Arwany said:
Ultramag69, Thanks alot for your consideration.
Flusching using SD card........ with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate..........
Click to expand...
Click to collapse
Hi,Just to tell You that I've noticed a little spelling mistake.You've written "herming.nbh" But it should be "Hermimg.nbh".
Not the 1st person to make that mistake, and probably won't be the last.....
Hi All,
Yeah, that worked out for me, I could successfully flush my JasJam with that.
Thanks for your reply.
I am still facing problem when trying to flush with other OS, its always stuck on the GSM line.
I am using the SD flush method.
Any suggestions ?
THank s alot for your help!
If you have the no GSM problem the only way to, maybe, fix is to flash the original SHIPPED STOCK ROM, or the original radio rom. Flashing anything else may result in a permanent brick...
If it doesn't succeed then, sorry, its not repairable. Can be used as a PDA but not as a phone ever again.
Cheers...
Thansks Ultramag69, for all the helps, It solved my main problem.
You also Ekonkar, your comments was so helpful.
I will try to do some hardware repairing in some Mobile shop, they may get it up again !
To fix it will cost more than to get a new device... They'll tell you they can't fix it or it needs a new mainboard. Will still cost you for this nugget of info. My advice, buy a Hermes off ebay, either working or not. If its not, make sure its screen related problem cos you have the parts to fix... Unless your screen has gone bung too...
Cheers...
I gave it to the repairing guy, he replaced the GSM item and its up and running now for only 20$.
Prost :-D
Sweet, You should post where and what country so others in the same situation might be able to get their Hermes up & running.
Hi all
I've had a search through the re-developed ROM's and to be perfectly open, I don't understand much about them.
I recently had a plain HTC HD2 and very happy with it for what I use it for, I don't need any fancy add on's and bits etc, just my Co-pilot and keeping my contacts and notes upto date.
That handset was lost and the insurance didn't have any HD2 replacements in stock. The Desire they sent instead has been sold, and I've purchased a T Mobile version of another HD2.
Is it a simple case of downloading and installing the official HTC ROM for the handset and doing a ROM update?
Apologies if this is a simple query etc!
Cheers, Dennis!
no, no no nonono.
assuming you mean a tmobile us model (1024 rom, green send key) then no, if you flash a non tmous stock rom (any stock rom that isn't for the tmous) onto that phone it will die. brick. dead, because of the ..51.. radio they include.
You may get some cooked roms that are on a base of lower than 2.x, but have been tweaked for the 576ram , and they will work on your phone, but its a very risky game to play.
Far better to follow the two rules..,
only ever flash tmous stock roms,
and
cooked roms that SPECIFICALLY say tmous compatible in the title and post 1 of that roms thread..
Hiya
Samsamuel, thanks for the info there. I'll update with more information! I'm technical, but not with smartphones to the level some of you guys here!
I'm in the UK, and it's a UK TMobile handset that I bought. I've already had the handset 'unlocked' so that I can use my O2 SIM, which is working etc.
From the handset
OS Version - 5.2.21889 (21889.5.0.87)
Manila Version - 2.5.20121429.0
ROM version - 1.72.110.4 (86525) WWE
ROM date - 04/02/10
Radio Version - 2.07.51.22_2
Protocol version - 15.32.50.07U
So, would it be ok to update to the normal HTC ROM?
Cheers, Dennis!
Ah ok in that case there is no need to mention that it is a t mobile phone, just confuses the issue.
Yes the regular update will work fine once happy is applied.
Thanks once again SamSamuel,
However, what's meant by 'once happy is applied' ?
Is that one of these hacks or special ROM things?
When I do a search, so many results come back containing the word 'happy' I have no idea where or what to look for!
Is there a thread which explains how to apply 'happy'?
Apologies for the vagueness!!
Cheers, Dennis!
lol, thats the android spell correction and me not proof reading before i post. should be HSPL
Hiya
To me, anything that's typed up 'could' potentially be what I need to do! I wouldn't know the difference!!
So, I've had a search for HSPL - I see it mentioned, but alas, I have no clue what it is, where to get it from, what to do with it when I get it!
Is there any straightforward points on what and where to get this HSPL, how to use it ?
I know I can download the HTC official ROM from their website, so that part I think I know what to do as I upgraded my last HD2.
Cheers, Dennis!
ok, hspl. Get HSPL2_RUN.zip from HERE, (you can follow instructions that say hspl or hspl3, theyre all the same, except for what phones they support, , hspl2 is teh most usefull for regular hd2 owners)
phone into bootloader and connect usb, (when you read 'get an active sync connection', , forget that, it doesnt mean actual active sync, just a usb connection)
get hspl2, run it, in the dropdown is a list of spl and hspl versions. if it ends .0000 its stock, if it ends .hspl its,,,,,, hspl.
choose 2.08.hspl, follow the prompts. if it doesnt work, run the hspl prog again, if it still doesnt work (timeout/connection errors) change usb ports and try again. no need to touch teh phone, just leave it in bootloader all the time.
once bootloader says spl 2.08.hspl you are good to go.
BUT
if you are planning to flash the 3.14 rom, , , you can't do it this way.
3.14 wont work on any spl/hspl except 3.03.0000 and there is no way to get 3.03.0000 except goldcard.
Hiya
Samsamuel - seems you're the only one willing to help me here! so I really appreciate it !
I know i've got to do 'things' from what you've said there, but I have no idea on how to do it! - give me some financial IT related stuff I'm good! ask me to do bootloaders and potential goldcard and run files and connect - I'm lost! I don't want to try things in case I 'brick' the handset!
The ROM I want is listed on the HTC downloads section for the HD2. It's dated 25th January 2010
Details are
ROM Version:
Norway:1.66.409.1, Spain :1.66.412.1, Denmark:1.66.403.1, France :1.66.406.1,
Sweden:1.66.413.2, Italy:1.66.408.1, WWE:1.66.405.2, France Bouygues: 1.66.483.0
So, if I somehow manage to do this HSPL thing, will I not be able to install the HTC ROM? I have no idea where or what the '3.14' ROM is?
Apologies for sounding really vague - I've never got into all the modified ROM's and stuff for smartphones. I've only ever needed to switch on, use the phone, install my GPS software and keep my contacts and notes syncronised. I'm just used to the HD2 I had as it was a case of straightforward use. This T mobile version is 'different'!
Anyone else able to help alongside everything SamSamuel has kindly provided so far? please?!!
Cheers, Dennis!
warning
Its best for you if you do not try to update your phone. Either get used to it or just sell it. There are rom update tutorials on this site. Just search for rom update tutorial, if you must try. The official htc software is not for this phone, if you install it, your phone will no longer work, and you wont be able to fix it.
No, its ok so long as you have a regular hd2 locked to t mobile as discussed in earlier posts.
Just to double confirm, if your phone has green send key,then STOP DANGER
But I think we're dealing with white send key, so normal hd2, and the target Tom isn't 3.14
So,,,
assuming white end key.
Phone backed up and off
Press hold keep holding volume down
Tap and release power keep holding volume down
When striped coloured screen appears
Plug in USB
On PC run hspl2
In dropdown choose 2.08.hspl
When it completes and phone starts to reboot immediately hold volume down again to return to stripey screen (bootloader)
When says USB at the bottom and split at top says 2.08.hspl run the .exe you downloaded from HTC
If you get connection errors, timeouts, leave the phone and just swap USB ports. When running hspl.exe right click it and "run as administrator"
(That's the last time I'm gonna write those out in full, there must be 500 identical step by steps and half as many YouTube vids. )
If your send key is green DO NOT DO THIS
Hi folks! Please help me! I killed tons of nerves because of this phone!
So here is my sad story. 1 Year ago i bought second hand HTC HD2. Seller told me that phone is locked to T-mobile(Not US one!! UK one!! Transaction was held in UK). After I got phone I rushed home to install Android and I was successful at this point. Then I bought a unlock code from ebay, so I Finally could make phone calls. Then I realized that the only way I can insert code is putting back WM 6.5. And here the worst part starts. I read hundreds of manuals but still was unsuccessful. I downloaded many official WM 6.5 ROM installers but they didn't flash my phone. They just got stuck at 0% and error pops up. I was trying it for a week and then I just raged and put phone to the shelf and was waiting til I get will power to start over again.
I hear that every phone needs its own ROM installer for particular region and operator but I couldn't find UK T-mobile ROM so used many others and it didn't help.
I also heard that by IMEI it is possible to find to what operator the phone is locked(just to check if seller didn't lie me) but again I didn't manage to do so.
Here is my IMEI 354120035834066
Please experts help me, little nooby, with this horrible situation.
thank you
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
samsamuel said:
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
Click to expand...
Click to collapse
Thank you, but always when I am trying yo install HSPL4 critical error comes up. I think it comes up because I have spl 2.1000000 which should be 2.08 I found information that in order to downgrade to 2.08 I need to flash official ROM. But when I am trying to do so it is always stuck on 0%...
I am so $%^& up ...
any ideas?.... thx
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Mister B said:
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Click to expand...
Click to collapse
Hi. Thanks for ROM, but still.. got stuck on 0% and doesn't go further..
When I try to install HSPL4 it always gives me critical error...
Fixed my problem. Now everything works fine!! Thank you very much guys!!
how ??
rom4eg said:
Fixed my problem. Now everything works fine!! Thank you very much guys!!
Click to expand...
Click to collapse
explain