Appologize for posting the thread twice... I wasn't sure if this goes to the Hermes or the Herald forum...
Hello All,
I recently got an ATT 8525 and I'm trying to use it with my T-Mobile (US) SIM. I was able to successfully unlock the SIM and CID with an util/rom I found on this site (I think the post was from Pof). And I also re-flashed the phone with the latest ROM available.
But after about 5-10mins of usage the signal dies and when I reboot it says No GSM. Looks like the Radio ROM gets corrupted. I tried just re-flashing the Radio ROM and that doesn't help either. It works for short while and again the signal dies.
And also, I'm unable to install any of the generic ROMs (Fantastic Mobiz, PVET 40005) Although I'm connected to Active Sync when I run the Step 1 (ROMUpdateUtility_NV_G3.exe), I get a ERROR [222] : DEVICE NOT RESPONDING. And when I run the step 2 directly (update_rom.bat) I get an cannot update itsutils.dll maybe in use error.
As you can tell I've been messing with phone a lot for a couple of days with no luck and my frustration level is kinda high
As of now here’s where I stand. I re-flashed the phone (Image: 3.62, Radio 1.50) and it’s on the “Tap the screen to set up your windows based mobile device” screen. I plan on leaving it on this screen until I can a good solution.
I would like to get rid of the ATT ROM and install one of those hybrid generic ROM that is not Carrier specific. Any help will be much appreciated. Share your ideas, I’m very experimental
Phone Details…
ATT 8525
HERM100
IPL: 1.04
SPL: 1.40.0 lipro
ok ur going all over the map here.. did u hardspl first? also pvet 40005 isnt a hermes rom.. um try hardspl first THEN flash to a new rom maybe once you successfully do that then try a new 3.62 rom.. i run austinsync buts its naked..just like i like my women. ha. but if ur looking for a full blown try fun_key's rom or blinkys.. these arent carrier dependent
hey man jakeypoo, Thanks for your reply. I kinda figured that I was all over the map.
Okay first appologize my ignorance. What is a HardSPL? I did a search on this forum and I found Hard-SPL-V7.zip. Is this a good version to use? Also when I run the exe, All options are grayed out except for "Force Using SSPL" and "Is it Hard-SPL". What do I select.
Thanks!
Hardspl v7 is the latest version out there, its the one for you to use so that you're safe from future mishaps.
I also have an 8525 on T-mobile... so no worries.
Hope this helps.
http://wiki.xda-developers.com/index.php?pagename=Hermes_HardSPL
still problems (no gsm)
Thanks whistler4ever. That link was really a great help.
Here's what I did...
1. Installed the Hard SPL version 6
2. Installed the latest ATT ROM (ver 3.62 radio: 1.54) I had to do this because the radio on the phone was corrupt (says "no GSM" on the start screen) and couldn't install just the radio rom. kept giving connection errors.
3. Installed Schap's WM6 Pro 3.57 hoping this would get ride of the ATT ROM and my intial problem (no GSM) will go away.
Everything was fine for like 15 mins, then my phone just froze. I reboot the phone and sure enough the radio ROM was gone (no gsm). ;(
Running out of ideas.
1. Could this problem be because I'm using a TMobile SIM on a ATT's radio ROM?
2. Is the radio ROM specific to the phone type and provider(ATT, TMO..)? Is there a generic WM 6 radio rom? If yes, where can I find the latest version?
3. Any bright ideas?
Thanks again!
Current phone details...
ATT 8525
HERM100
IPL: 1.04
SPL: 2.10
ROM 3.62
Radio: no gsm
I was able to flash just the radio ROM - version 1.51. But again after a few hours the Radio got currupted. I also tried to follow the instruction ( http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5 ) to use the mtty.exe utility, but I don't get a USB prompt. I get Cmd prompt and if I still enter the password, it says invalid password. please help!!!
And how do I do the USB monitor capture? I could post more details that way. I'm using my girl friend's old razr now and it's painful!
I have used my t-mobile sim on AT&T rom's and other roms with no problem. I would try going back to a factory rom and then changing back to a cooked rom just to confirm its all a clean install. also, try downgrading your radio to a 1.47 or 1.48 (those have been proved pretty reliable across many cell providers).
Thanks Whistler. I'm going to start with the 1.48 version and if that doesn't work I'll try the 1.47 version. Not giving up on this.
I found 1.47 to work very well with t-mobile even when traveling...
Thanks Galaxys. I just installed the 1.47 radio. I have fully signal and the 'E', but I can't receive or make calls.
It almost looks like my TMO SIM is not compatible with the 8525. It always works for the first few minutes after an install and then stops working.
I'm very certain the phone is in good condition.
Should I try an older radio version.. like a 1.24 or something ?
Can I install just the tmobile radio rom?
I'm also going to install TNT 2.0 pro so I have the exact same set up as you and see if that makes a difference.
no luck!!!
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
try the way i posted in this thread http://forum.xda-developers.com/showthread.php?t=337125
ajjus said:
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
Click to expand...
Click to collapse
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Try to flash the entire UK T-Mobile ROM, then remove the internet settings and install the correct CAB for T-Mobile.
UK ROM here: http://forum.xda-developers.com/showthread.php?t=337163
PROVIDER SETTINGS CAB: http://forum.xda-developers.com/showthread.php?t=311446
a-h-t1, Junner2003 and galaxys - I'll try all your suggestions.
a-h-t1 - The first 2 steps went through fine. While I install the radio ROM as part of step 3, the installation doesn't go past 0%
I'm going try Junner2003 idea now. I'll keep everyone posted on my progress.
install stops at 11%
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
galaxys said:
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Click to expand...
Click to collapse
Hi Galaxys,
I don't think the IMEI is blocked. Or maybe it is, how do I find out? I don't have any of the symptons listed on the link you sent (don't hear the beeps or anything).
I originally had a T-Mobile wing. The LCD screen cracked (don't know how). And ofcourse TMo won't replace it.
http://forum.xda-developers.com/showthread.php?t=335346
I got 8525 from my company. It's almost new. Only used for a day on an AT&T SIM. This phone is free, and so I really don't have much to lose... so all out experimenting
Tried insalling from the micro card, even that stops while installing GSM. pissed!!! Why would the darn Radio not update???
this may sound stupid but if all else fails, why not...
my mda use to have signal then it would just disappear as well after 15 min or less..
turns out the sim card wasnt pressed in properly.. so i just put a piece of paper on top of the sim card to make it thicker and get the battery to press it down harder. and it solved all my problems...
just a suggestion..good luck
ajjus said:
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
Click to expand...
Click to collapse
See this post here for a possible reason (and technical explanation/theory) for your device stalling during radio update. The fix suggestions at the bottom of the page may help you - in particular :
Try cooling the device down a bit before flashing as the PIC chip (where your radio ROM is held) may flash more reliably/easier when cool. Don't ask why - that's from it's datasheet ;-)
The paper on the SIM card is a good idea too to rule out dodgy SIM connection - Great idea r0mmel
Related
I unlocked my SPV M3100 via these instructions:
http://forum.xda-developers.com/showthread.php?t=293665
Now whenever my phone goes into bootloader mode it doesnt seem to connect to my PC. I wanted to upgrade my rom to the newest one available of the orange website but cant seem to connect. It always comes up with error [260]. I think that means something about open connection error.
Ive read quite a few topics and can seem to solve it. Any help would be much appreciated.
Thanks
Same here !
Anyone?
OK both you guys need to read ALOT more before flashing anything else...
..the bootloader has been upgraded which is why the standard retail RUUs (Rom Update Utility) dont recognise the device any more.
..
..
Im deliberatly not telling you the remedy in hope that you follow example and read up...remember guys these device are EXPENSIVE and plunging in the deepend is never a good idea.
CLUE:: my signature.
Thanks for the reply mate. I take it that the best thing to do now would be to follow your guides and upgrade the rom to a different one such as the black majik.
My original plan was to unlock it so i can use a t mobile sim. Now that i have done that it doesnt work. I have reception on the t mobile sim but whenever i make a call it cuts off straight away. I have upgraded the radio to 1.38 (the latest one for orange). But now when i put my orange sim in i dont get any network. And the t mobile sim is still not working
The current stats are:
IPL - 1.01
SPL-1.40.Olipro
operator version: 14.123.1.614
rom version 1.23.61.4
Rom date: 07/13/06
Radio version 1.38.00.01
I think i may have bricked this. Is there any way i can remove everything and take it back to standard. Someone please help im loosing the plot here.
look man, again just follow the guides and read through threads......the radio situation is quite simple, flash a newer one.
If you follow the black majik guide you will have the latest SPL/IPL and Radio.
Thanks for the replies mate. Ive read quite a few topics here and on modaco. Ive also read the topics in your sig. I upgraded the radio to the latest one but the phone is still not working. Once i put the orange sim in i dont get any reception. If i put the t mobile sim in i get full reception but when i go to make a call it cuts off.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
RaDeNRFX said:
- I am so sorry posting this twice in the wrong sections, it seems that i'm a really noobie forum user - But i finally found the rite section. So my humble excuses.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
Click to expand...
Click to collapse
ach2 said:
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
Click to expand...
Click to collapse
I waited till the Program says connection error...and send me to recovery proces. And i've been making hella tons of coffee after trying to flash that many Radio Roms. Any other suggestions? I'm so desperate
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
ach2 said:
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
Click to expand...
Click to collapse
Well the weird part is "No GSM" appeared occasionally...some times it shows it sometimes it's not showing it.
No...i'm a Vista hater. And dun have the original manufacturers ROM. I've got the "T-Mobile Vario II" from The Netherlands..so if anybody got a link for the original version i'd be thankfull.
The Radio it self is intermittent and very inpredictable...for example:
Radio indicator says i got full recieve:...but i can't call or recieve any.
Connection error: 262 (which is, if i'm not mistake a connection error.) Which is bull cuz i'm re-running every other ROM's upload with the same way and succeded/
Radio indicator says no reception and shows an exclamation mark:...and my GF just called me to hurry up and pick her up :/
But the weird part is...it seems that my radio ROM is locked somehow. I can upgrade or downgrade SPL's and OS ROM's but not the Radio ROM.
I've tried to use MTTY by now and followed the manual bellow: (Problem 5)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
But it began with invalid password. Procede as written and it didn't helped.
More suggestions are welcome
My bad...i didn't looked well enough. It is saying No GSM the whole time.
More information:
I've checked the Device information on the Hermes now some information are blank:
Radio: Blank
Protocol version: Blank
IMEI: Blank
All other information field are filled. Been spending hours reading tutorials and manuals...and nothing. HELP!
OK,
This isn't a problem I've had myself, but loads of other people have and there are quite a few threads on how to unbrick from here... you're going to have to do a bit of reading.
This page shows the different combinations of OS/radio/brick type etc and should point you in the right direction for the correct course of action http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Then read through this thread http://forum.xda-developers.com/showthread.php?t=286755 . It's got really long but read the beginning where POF describes the types of problem and also the solutions. Then it's probably best to jump to somewhere near the end and pick someone who has a similar problem.
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
ach2 said:
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
Click to expand...
Click to collapse
I am really thankfull of ur post. Unfortunately, i've been doing some reading. Including the link u gave me. The problem is that i can't upload/flash Radio in nhb format.
As i described in the first place, i can't load a nhb format radio in RUUWrapper.exe properly. It can start the proces..but it always end up with a connection error code 260/262 during the installation progres bar (0%).
The solutions some ppl tried in ur link is often not my case. And the similar cases i have tried where i end up with the same grumpfy situation.
have you tried to flash the radio using the SD card method? I too have a cable connection problem but I fear mine may be hardware failure.
Yap...and no luck
Hello all,
I Eb'd an HTC wizard (cingular 8125) running Wizard Love/NBD WM 6.
On the load screen I get:
AKU 2.3;
IPL and SPL:2.25.0001;
radio:2.25.11;
rom: 6.0.0.0.
My carrier is Tmobile.
Question 1: If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I wanna update my rom and think that I am competent enough to do so but there is alot to learn and this is not my full time gig...right.
Question 2: So, if I am correct in Q1 I should be able to flash roms right?
However when I attempt to do so the RUU gives me [error 224]. Active sync and or WMDC says its connected. (I installed the AS drivers in WMDC)
Question 3: Where do I go from here?
Question 4: The wi-fi is currently not working will a new rom potentially clear this up?
Thanks in advance for the time and advice..
grazie
hmmmm,
Well,did you updated to NBD wm6 yourself ? and how did you updated ? which method you adopted ? SoftSPL or HardSPL ?
You say its SIM unlocked as it takes calls on the Tmobile network .Did you SIM unlocked with lokiwiz03a ?
yes ! a G4 can be SIM unlocked but it can not be CID unlocked,however,it can be upgraded to wm6 rom,but with method either 'SoftSPL' or 'HardSPL'.With your present ipl/spl 2.25.0001 and you say its NBD wm6 running,then it must have been upgraded through 'SoftSPL' method,as it uses patched ipl/spl and Cid unlocks the phone temporarily,but it never permanently CID unlocks the phone.But with 'HardSPL' ,it changes the ipl/spl to a patched ipl 2.21.0001 and spl 2.21 olip.So everytime you want to upgrade,you'll have to upgrade using 'SoftSPL' method.
could you elaborate a little more about this.
Cheers!
Hey thanks for the correspondence zabardast_1, I have been getting frustrated and I have many times contemplated going for the brick or bust approach here.
So, I have done none of the updating on this rig. I rec'd it and I wanted it primarily for wifi however I can't get the wifi card/ (sdiowlan I believe) to even recognize an AP (... I posted in the networking forum but no response.) Thus my own reasoning leads me to believe I should start from scratch with a new rom unless you know of something else.
So, I am not the most savvy and thought that all of the info I had led to SIM and CID unlocked. I just read otherwise last night and in your reply. The info I have provided is accurate the IPL, SPL, radio, although I don't know which NBD release it is; just says 6.0.0.0 and release date: 2/2/07.
I am trying to get the new rom on the my device however and I would've probably already bricked it if I could get an RUU to communicate with my wiz. I always get [Error 224] when I run it and my phone is connected through active sync. I am running vista but have installed the AS drivers for WMDC. I also tried it at work the other day with XP same situ. I then tried flashing from the bootloader screen with an NBD, Wizard Love ( w/ Italian installer?), and T-mob (226102_22610105_022511). The only one that says it will update is the Tmob ROM, however I got cold feet at the update button and canceled.
Other funny stuff I have observed that may or may not be related to the problems I am having are:
Can't install cab files ie (enable rapi or Cert SPCS) and Wiz Sys Tools couldn't read my CID block and hard_SPL G4 gives me REXX error ( SPL_Version has no value).
So, any wizdom you or anybody can drop is much appreciated and needed at this point.
Whew...
Listen carefully. G4 Wizard cannot be CID-unlocked without paying money. (And yes, you are using a G4).
What you need now is to Flash your original stock carrier ROM (Or wizard love) to get your OS back. Then either use SoftSPL or install HardSPL and flash WM6 ROM.
Thanks Starkwong,
I will try installing wizard love tomorrow at work and if that don't work I will attempt a Cing ROM (will all of these work or do I need to mind my G3's and G4's for these???)
Grazie
So, It worked using Wizard Love at work and out of the bootloader window. Now I need to:
1.) Get wifi working.
2.) Get a newer ROM
I put a post up in the networking thread, I am a tool so far as these devices are concerned so be easy on me.
http://forum.xda-developers.com/showthread.php?t=372811
So do I get the wifi issue resolved before I reflash???
Thx again
I don't know what you mean by "wifi not working".
Maybe it is the wifi AP doesn't allow 11Mbps (802.11b) connections?
However, going to any of the WM6 ROMs should already set the registry to allow Wizard connects to G-Only APs. Just use HardSPL/SoftSPL and flash a WM6 and you will see.
OK so "wifi not working" may indeed be a general statement...
What I mean to say is that I am not able to connect to any wireless networks for internet not home (Linksys WRT 54G v5 with ddwrt firmware) or school (university wide) or my city's wifi network. It won't even detect them at least none that Ive seen since I've rec'd this phone. So, that is what I meant by the ambiguous statement.
So, being as your last post was a success I will try as you say and post the results tomorrow. Thanks again starkwong!!!
1 quick thing however, to be sure, I can now try the hard spl or soft spl method of tricking my phone to run an upgrade to WM6?
Still not able to get wifi APs????
OK although I have been successful at reinstalling the Mfg ROM and then Hard SPL'ing my wizard thanks to ya'll I still am unable to connect to a wireless network (see one even). I have the Olip on my SPL and I installed a TNT version of WM6 and I am still at work (drunk but still here). Anyway I can't see my wireless AP and I am beginning to think its a hardware issue if thats possible, i dunno the dynamics of this system maybe thats why it was for sale. In any event as usual I am willing to try what ever you guys throw at me as you're my only hope obi wan. Alright Im gonna go home for the night and try getting on to my home network.
Thanks again for all the help guys.
Is your device a original one from phone operator? I suspect your device is a China Dopod 838 with replaced casing, because the China version has the wifi hardware removed, so wifi can't be started even if an English ROM is used.
Looks to be authentic 8125
Starkwong, the Cingular logo and the 8125 model # are on the phone case where they have been when I've seen them before in pics. Therfore, I dunno I guess it looks like every other 8125 I've seen. Can I check the SN, IME or anything to be sure?
Thanks Again!!!
Starkwong,
I am getting all the options for wifi on my phone the LHS LED flashes green when I enable it and alternates blue green when BT is enabled. So, could it still be that its a dupod? I dunno but I am going home for the night... Thanks for your help. I will try connecting to my home network when I get there.
Can anyone share their experience upgrading their Bell HTC6800 ROM (including radio, unlocking SPL, and upgrading PRL) with DCD 3.0.1? I have never done it before but curious to hear if anyone has had success or failure.
I noticed that DCD released a Bell ROM in his 2.3.2 kitchen but not in his 3.0.0 kitchen. Does anyone know how to port the correct Bell settings into the 3.0.0 release?
My main reason for upgrading is of course better performance but more importantly I am curious about aGPS and how I can use it instead of my Bluetooth GPS receiver. If anyone can share that would be much appreciated.
http://rapidshare.com/files/99219142/DCD_3.0.1_Bell.exe
Check the last page of this thread
http://forum.xda-developers.com/showthread.php?t=363693
Thanks origins81. I noticed now that DCD added the Bell ROM to his 3.0.1. So can you share you experience with this ROM upgrade? Did you have any problems (I assume you've done this before)? Can you share your experience if you are a Bell HTC 6800 user?
1. If you have not already done so, run the 2.40-olipro unlocker. Your device will again be left in tri-color screen.
2. Flash the official sprint 3.35 update.
3. When the device boots for the first time, do not pass screen calibration. Flash a 3.x.x ROM. (that being the custom rom of your choice)
Think I only used the official Bell rom for about a day before i got sick and tired of it and flashed to one of DCD's clean roms, never looked back since then...
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Thanks guys. You have instilled more confidence in me now. I am just going to make sure I have the original stock ROM from ustar as well as the Titan re-locker just in case (I want a backout plan). I will wait a little longer until everyone irons out the kinks of this new 3.35 radio and I will give the latest DCD ROM a try. Thanks again!
I've used the SPRINT update and it works fine. I've added the quick GPS program that comes with the DCD version and I am going to change the startup logos from Sprint to Bell...(As soon as I figure out how). I didn't need to reprogram anything!!
I just got my phone today, gonna give this a shot...
oh man... i ran the olipro 2.4 file and it took me to the tri color mode and then tried to flash it with the latest sprint update. it went up to 4-5% and then it showed an error of Update Utility. i tried to go bak to the Bell update and it did the samething but this time after 1%. can someone please help me out here? I'm with bell.
ok now i'm stuck at the bell screen and at the bottom it says "No Radio" cuz i tried flashing the dcd file.
Well, to begin with, here are the steps I took to accomplish what I have.
1. Flash Olipro 2.40
2. Flash Radio to 3.35 (For the newest version of DCD's rom)
3. Flash the ROM to DCD's rom.
Now, the first time I did this, I got stuck at the tri-color screen, such a pain. I then tried flashing the rom again, and it rebooted continuously and I had no idea why. This was because I didn't flash to the newest radio. So I did that, and it worked, so try those steps, and good luck.
On problem that I did notice is that my phone always has the roaming triangle on?? Hopefully it's not costing me roaming charges... I was going to try and use the DCD 3.0.1 rom but don't want to chance it. I'm going to try playing with it some more an see what happens.
I'm running DCD 3.0.1 on my Bell 6800 and it's working great so far (day 2)
Follow Origins81's install points above, and remain calm if it takes a try or two to get past the 2.40-olipro unlocker 3-color screen step.
I'm having some issues ActiveSync'ing to both work and home PCs, but I don't think it's related to this ROM.
GPS works great with Google Maps
The alarm clock bug is fixed (e.g. not working when plugged in)
Got it working and everyhthing is great except is doesnt play video in the media player...Working on it.
Well for some reason I can't seem to activate my phone. I hit Talk then I enter ##911224#. It tries to connect for 15 secs then hangs up.
I _thought_ I did everything properly.
1) Ran Olipro2.40 (actually it was the unlock from http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/) it looks like it's got Olipro2.40 in it.
2) ran official upgrade from sprint (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship.exe)
3) Extracted DCD_3.0.1_Bell.exe and ran the RUU.
hope I didn't perma-brick it.
M
Ok fixed it. Browsed around the and found out in a Howard forum that you have to type ##111111# (doh!) before. Ok my heart can start beating again! Posted for posterity. The code that I used must have been for a different area. This phone is from the GTA.
can you give me a link to those howard forum posts because i ran into a problem ... after a last flash my phone works but its not activated... I tryied ##111111# but i get a code check error... ##911224# doesnt do anything... ##778# works but 000000 code doesnt so i cant get in... HELP
Roaming After Update
After suffering with the pesky Bluetooth issues with my HTC, I thought I'd do some searching on the Internet to see if others had the same issues. Lo and behold, it looks like a real bug with the HTC. After reading some forums, it looked like the latest Sprint release would cure the problem. I downloaded an unlock program ("Hard-SPL-MFG") and the Spring update (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship)
and proceeded to update my HTC.
After a few unsuccessful attempts (stuck at the three color bars a couple of times, restarting a few times on it's own) I managed to get the unlock code and Sprint update installed.
The problem I have now is that it appears that I am now roaming even though I'm in my calling area (I'm with Bell Canada)!
Help! What should I do??
Check the bottom link out, had similar issues when I first flashed. If you have any further questions let me know
http://forum.xda-developers.com/showthread.php?t=363693&highlight=FOR+BELL
i follow the step, but when the phone restart, i stuck a the bell screen...
i'm unable to connect with the usb.
Can you able to help me ? to complete the installation or trying to go back OEM
- i do the first step; see the red, green, blue screen (http://forum.ppcgeeks.com/showthread.php?t=9093)
- flash the rom
- now stuck......
thx for your precious help
TwistedWaffle said:
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Click to expand...
Click to collapse
Hi TwistedWaffle, Are you from the montreal region? I am looking for somebody who would do this stuff for me... Can you help?
Hi everyone,my name's Larry and I just registered to the forums. Please forgive my newness but I am in a bit of a pickle here.
I have a MDA Vario II, aka Hermes 300, that I bought s/h off ebay. Works fine,no worries, but I upgraded to WM6 because i felt browsing was a little slow and the screen graphics werent as good as I expected. The upgrade was from the T-mobile site itself and all went fine. Only thing is I dont believe this phone can handle it(needs more RAM really) and after being online a while it gets really slow,like steerig a cow through treacle at times so I came to the conclusiong it was a bad move! Now I've noticed a link on here about downgrading to WM5 but is it that easy for one with no specialised tools or knowledge(tho i did build my own PC, or should I say ahem WE did)
Also a problem the phone has developed since the upgrade is it keep deleting my email settings, even tho on the 'desktop' screen it tells me i have so many unread emails in each account! So now i cant check emails from it either!
I do hope I can sort this out cos it is really frustrating having a PDA and not being able to browse properly!
Many thanks
Larry
Welcome to XDA-Developers larry. Well Firstly i would start with CID unlocking your device so that you can flash any rom you can do that by downloading hard spl from here
http://forum.xda-developers.com/showthread.php?t=296722
then once you have flashed that you can basically download and install any rom for the hermes. I have an mda vario ii and hate the t-mobile rom as it installs quite a bit of useless crap. I never use and it is also so damn ugly. if after installing a new rom you find you have internet connection problems and/or mms settings then download and run this http://rapidshare.com/files/92547562/UK_Setup.exe that will install the settings for internet and mms for all uk networks, the majority of the cooked roms on here though ,already have a network wizard to set it up for you, but better to be safe than sorry
P.S. I forgot to add if you are looking for speed and extra ram i would look for a vanilla(clean) rom, install that and then add the apps you want via cab files, you will find them scattered about all over this site
scousemartin said:
Welcome to XDA-Developers larry. Well Firstly i would start with CID unlocking your device so that you can flash any rom you can do that by downloading hard spl from here
http://forum.xda-developers.com/showthread.php?t=296722
then once you have flashed that you can basically download and install any rom for the hermes. I have an mda vario ii and hate the t-mobile rom as it installs quite a bit of useless crap. I never use and it is also so damn ugly. if after installing a new rom you find you have internet connection problems and/or mms settings then download and run this http://rapidshare.com/files/92547562/UK_Setup.exe that will install the settings for internet and mms for all uk networks, the majority of the cooked roms on here though ,already have a network wizard to set it up for you, but better to be safe than sorry
P.S. I forgot to add if you are looking for speed and extra ram i would look for a vanilla(clean) rom, install that and then add the apps you want via cab files, you will find them scattered about all over this site
Click to expand...
Click to collapse
Ah thanks for that but I have no idea what CID unlocking is(do you mean like unlocking the phone to other networks?) Also what's hard spl?? Totally in the dark about this!
Hermes300 said:
Ah thanks for that but I have no idea what CID unlocking is(do you mean like unlocking the phone to other networks?) Also what's hard spl?? Totally in the dark about this!
Click to expand...
Click to collapse
all your question answered here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
I have looked thru the wiki and cannot find the advice I need.
My device has the following on it and what I would like to know is if I can actually drowngrade the device back to WM5.
The rom version is 3.60.110.4 (T-mobile UK)
The radio version is 1.50.00.00 so I assume that it is boot 0108.
The IPL is 1.04 and the SPL 2.03.
The protocol reads as follows 32.83.7020.20H
I have come across a guide that states if the radio is above 1.27.00.00 then downgrading may not be possible.
"(NOTE: If your radio version is currently HIGHER than 1.27.00.00 then it is very likely the radio bootloader is version 0108, this WILL NOT allow the radio to be downgraded to a radio containing BL 0106 and will result in a "NO GSM" error.)" -http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
The other question I would like to ask is this - it is possible to put another verion of WM6 on with this radio version?
Thanks for any advice!
Can anyone help me here!
Do I need to SIM unlock my PDA to update the ROM to a custom ROM, for example Schaps_WM6Pro_Hermes_4.30 which I recently downloaded from here.
At the moment it is locked to T-mobile. I have also updated the SPL to 2.10 olipro and the radio is at 1.50.00.00 and the HTC boot is 0108.
Thanks guys
Larry
Hermes300 said:
Can anyone help me here!
Do I need to SIM unlock my PDA to update the ROM to a custom ROM, for example Schaps_WM6Pro_Hermes_4.30 which I recently downloaded from here.
At the moment it is locked to T-mobile. I have also updated the SPL to 2.10 olipro and the radio is at 1.50.00.00 and the HTC boot is 0108.
Thanks guys
Larry
Click to expand...
Click to collapse
I think you might not have gotten help 'cause it doesn't look like you've read what people pointed for you to read. Hopefully this'll help you get over the jargon hump and make progress. Having upgraded from the Offical T-Moble rom and swapped ROMs, it's definitely worth taking the time to learn how to do.
SIM unlock & CID unlock aren't the same.
If you've had you phone with T-Mobile for at least 3 month they will let Unlock you SIM (at least they do in the US). Contact them directly, you'll need an active account & phone number with them. This is free.
CID unlocking allows flashing ROMs onto your PDA. For some reason the folks at T-mobile, etc want you to have to look at their stuff every time you use a machine you bought through them. Using a cooked rom is like reinstalling XP without having AOL on your computer, makes life much better.
(flashing = installing to a PDA's Read Only Memory)
(ROM = OS + Radio + other stuff = basically everything thats on the PDA after a hard reset)
Flashing can be a dangerous thing, you don't want to 'brick' your PDA so you install an escape hatch. Hard SPL is that escape hatch.
(Brick = peice of baked clay = your PDA if a ROM install fails and you didn't install Hard SPL first)
The Hard SPL protects you if the ROM you installs fails 'cause power went out, ROM was bad, you bumped the cable, etc
http://forum.xda-developers.com/showthread.php?t=296722
Read & Follow the directions.
Select a ROM from here
http://wiki.xda-developers.com/index.php?pagename=Hermes_Cooked_ROMs
I have the same model & just installed Custel V2.5, seems to work well so far (day 2).
http://forum.xda-developers.com/showthread.php?t=364617
Good Luck
Thanks gt, and we have read advice on here but a lot of seems to be conflicting plus we seem to be just going round and round. Yep, ben there, yep read that etc.
I know the diff. between SIM and CID unlock but all I want to know is is it necessary to SIM unlock the phone to update a ROM?
I wont be using another network but will be staying with T-mobile W n W.
I did it!
Well I did it. flashed the phone with Schaps WM6 4.30 WWE.
Have noticed it runs faster than the previous T-Mobile WM6 and has some really neat features-you can adjust a lot more settings on the phone than before,quite impresed! Thanks for everyones help!