Hello,
I've got a strange problem.
I connect the phone with my A2DP receiver in my car. The car audio has the function to switch automaticly to source A2DP if there is a signal.
On first connect everything works fine, bun on reconnect (leave the car, come back and reconnect) the phone sends a very low noise so that the car audio switches to A2DP.
There is no player running on the phone.
Samsung voice to go and vlingo or similar are not installed (I hear the same noise when vlingo is in listening mode).
When I start a player, start music and stop again, the noise is gone and the car audio swiches back to radio.
If I use a MW600 instead I can hear the noise too, when I turn the volume up.
I had the issue with Stock KI4 and now with CheckROM V6 too.
Did someone noticed this noise too? I there something I can do?
thanks
Andre
Related
Just had to share a surprising and accidental solution that occured. I have a TMOUS HD2 with the 3.14 ROM update and CHT 2.0.
I recently purchased a Monster ClarityHD bluetooth speaker so I could wirelessly stream music from my phone. After pairing it, the streaming and sound were quite impressive. After I turned off the speaker I noticed that the phone detected it but only as a headset and not stereo audio (as indicated by the icon on top, i.e., headset with bluetooth logo vs. headphones with music note). I had to go into the Comm Manager everytime to update the pairing so the A2DP would turn on.
I searched all over (including here) for an A2DP switch/toggle app but never found one that worked fo me. After talking to both T-Mobile and HTC tech support to no avail, I happened to reset my phone while it was paired with A2DP on, the bluettoh speaker speaker was on, and bluetooth discoverable was on (bluetooth logo with eye on top). After it rebooted it found the speaker and turned on stereo audio automatically.
I can't explain it but it's exactly what I was looking for it to do. If you try this I hope it works for you too.
Hi Guys,
i have problem with my sgs2... few weeks ago i've damaged my phone by pluging headphones jack to soundboard with phantom (48V) turned on...
So now my phone thinks that the headset is connected all the time and when i make a call, sound and mic is going thru headset even if its unpluged, so i can't hear anything from speakr and microphone is turned of...
Now i'm running on CM9 experimental build - so i can't use app toggleheadset2 like before on CM7.
Is there any way to do software headset "unplug", e.g. to use terminal to route signal thru phone speaker and mic?
Thx
i found a bug in .73;
sometimes if i listen to music with standard no mic stereo headphones (Sennheiser MX160), once i disconnect headphones and try to make a call the audio signal is not switched to the phone's speaker. so the call is mute, the other end can hear me but i can't hear the other end, if i connect the headphones and disconnect again the audio signal get routed correctly.
this doesn't happen if i connect, instead of Sehheiser headphones, the standard sony headphones or my "DIY" car stereo adapter...
I think it's an hardware bug, something looking for the impedence connected
I did notice an issue that's only occurred once, where audio wouldn't swap between headphones and speaker. I was watching a movie trailer at home on the loud speaker, then put my headset (aJays One+ with mic) in to listen to some music whilst on the move and it just didn't acknowledge the headphones. It took several restarts before the phone would correctly detect the headset and switch between the two. This was also on the .73 firmware.
Droid RAZR Maxx, stock ROM, rooted.
I recently installed an Alpine CDE-HD137BT stereo in my car, which has quite a bit of bluetooth functionality. However, I do have quite a few issues connecting my Razr's BT with the Alpine.
-Sometimes the BT icon on the stereo will light up, and the BT icon on the RAZR will turn blue, indicating that they are paired. However, even though they showing as being paired and connected, it occassionally won't play any audio through the stereo (in fact, the audio will play through the RAZR's speaker). This some times happens with CALLS as well.
-Sometimes the two devices will connect fine, which then automatically causes my phone to start playing music from whatever music app was being used last; the music will play fine through the car stereo's speakers for maybe 20 seconds, followed by a shrill, loud, high frequency tone that only goes away by switching the source or by turning the radio off/on (by turning the car off/on).
-Sometimes the phone will pair perfectly to the stereo, and I make a call before listening to any music. The call is executed beautifully, but then following the call, audio will not stream through the stereo, nor will any subsequent calls work via bluetooth.
-(known problem) the specific Pandora fucntions on the stereo do not seem to work with this device.
Anyone else have the above issues? If so, what did you do to remedy them?
Thanks in advance!
never had those problems before but I now how pissy bluetooth between phones and radios can be, I had a pioneer AVIC D-3 with the BTB-200 bluetooth module. When I first got it I had to manually pair it each time and the problem was that when setting up the pairing I had to have the radio discover the phone instead of the phone discovering the radio or vice versa I can't remember but that solved almost all of the problems I had then, every once in a blue moon my current radio doesn't auto pair, but its not a huge deal as this one doesn't do A2DP audio streaming it only does the Hand Free Profile and text message alerts.
Do you know of any application that manages your bluetooth connections?
Here's what I'm talking about, I have bluetooth headphones, several speakers and my car that all are connected to my phone and I'm having several small issues.
- As soon as I turn on bluetooth it tries to automatically tries to connect to these certain speakers, I don't want that and don't know how to stop it.
- If I'm in my car, my phone connected to my car for calls and I'm listening to music through the headphone jack but it will automatically connect to a set of bluetooth speakers in my home when get home and pull into the driveway. So music will play through those speakers instead of my headphone jack. I obviously don't want that either.
-Titanium Backup never restores my bluetooth connection either so if there is an application that can save those too that would be helpful.
Nothing? Any idea if I have to just deal with these issues?