i found a bug in .73;
sometimes if i listen to music with standard no mic stereo headphones (Sennheiser MX160), once i disconnect headphones and try to make a call the audio signal is not switched to the phone's speaker. so the call is mute, the other end can hear me but i can't hear the other end, if i connect the headphones and disconnect again the audio signal get routed correctly.
this doesn't happen if i connect, instead of Sehheiser headphones, the standard sony headphones or my "DIY" car stereo adapter...
I think it's an hardware bug, something looking for the impedence connected
I did notice an issue that's only occurred once, where audio wouldn't swap between headphones and speaker. I was watching a movie trailer at home on the loud speaker, then put my headset (aJays One+ with mic) in to listen to some music whilst on the move and it just didn't acknowledge the headphones. It took several restarts before the phone would correctly detect the headset and switch between the two. This was also on the .73 firmware.
Related
I just experienced a bug. I got in mij car, enabled bluetooth and stared the enging. I could hear the touch cruise connect to the parrot bluetooth carkit (usually it beeps twice, now it beeped 4-5 times).
I fired up my TomTom, instructions were given over the speakers of my car stereo (via carkit)!! I did some testing with other audio files, all worked over speakers.
Quality wasn''t sufficient for audio, but e-books and podcasts sounded good enough.
After a few minutes of playing arround I received a call, after hanging up the call the usual way on the carkit shut down the possibility to hear audio over the car speakers.
Anybody know a way to force audio over the car speakers through the handsfree??
Try this tool:
it sends all the audio signals to the headset (or BT Carkit)
Would it be possible to switch bluetooth audio on just when there is a sound to play, cause it seems a little bit useless to hear nothing when my navigation has nothing to say..
I have my SGS2 linked to a Pioneer DEH-P75BT car audio player.
The phone links to P75BT via bluetooth, and when I make or receive a call I hear the sound through my cars speakers.
If I use Navigation I don't hear any turn by turn navigation instructions, either through the phones external speaker, or the car speakers.
If I turn off bluetooth, then I start hearing the turn by turn instructions through the phones external speaker, which is what I want. How do I make the Navigation software audible through the phones speaker whilst the phone is still connected via bluetooth to the P75BT?
I'm actually thinking of getting a replacement audio system for the car, because the P75BT only lets me re-connect the phone if it's discoverable. I shouldn't need to keep doing that once they've paired.
Also I thought maybe a newer bluetooth car audio system might not suffer from the first problem I described.
Hello,
I've got a strange problem.
I connect the phone with my A2DP receiver in my car. The car audio has the function to switch automaticly to source A2DP if there is a signal.
On first connect everything works fine, bun on reconnect (leave the car, come back and reconnect) the phone sends a very low noise so that the car audio switches to A2DP.
There is no player running on the phone.
Samsung voice to go and vlingo or similar are not installed (I hear the same noise when vlingo is in listening mode).
When I start a player, start music and stop again, the noise is gone and the car audio swiches back to radio.
If I use a MW600 instead I can hear the noise too, when I turn the volume up.
I had the issue with Stock KI4 and now with CheckROM V6 too.
Did someone noticed this noise too? I there something I can do?
thanks
Andre
Hi guys, I'm having a problem with my bluetooth on this phone. I plug my phone into my cars speakers to play music and have my bluetooth headset on my ear for phone calls. On my Epic4G it automatically used bluetooth when a call came in.. but this phone doesn't. When I get a call I can answer it with my bluetooth physical button but it uses the phone mic and the car speakers. Is there anyway to fix this? I cant stand unplugging my aux cable EVERYTIME i have to answer my phone
thanks
I just had a random problem with the v10 where the headphone jack quit producing audio. The headphone symbol comes up and volume controls along with play/pause work from the headphones themselves. It was a software glitch I'm assuming as I restarted the phone in order to get audio back fine. I'll be cautious and see if it continues to happen.