has anyone successfully done this? i have a rooted fascinate running aokp milestone 4. i have read all the forums and have studied for hours. i finally got the nerve to try it....and....brick. lol i tried using heimdall. installed the drivers properly, opened the program, flashed the hacked param.lfs, program ran, phone booted into a blank screen for about 25 sec then went into recovery. tried wiping and restoring but right back to recovery i went. lol . had to odin to stock and build back up.
was just wondering if someone got this to work and could maybe give me a clue of what i may have done wrong..thanx.
Are you just wanting to replace the boot animation? In the case of AOPK, this would be the Unicorn animation. I do this all the time, directly from the phone. I use ES Explorer, although Root Explorer or an equivalent should work just as well. You'll need to go to /System/Media and delete the pre-exisiting bootanimation.zip. You can then replace this file with your preferred boot animation and be good to go. You can also move the old bootanimation.zip to your SD card before replacing it, allowing for easy recovery if you decide you want it back. You can also place your preferred boot animation in /data/local and supposedly a re-flash won't overwrite the boot animation. I haven't done this, as I prefer to see what animation is included in the ROM, then change it out if I wish. I'm sure there's other ways to accomplish this, but this procedure is quite simple. My preference at the moment is the rockets animation from makelegs' CM7 Kang, but there are lots available for download. Or, you can make your own if you are so inclined. I have a folder on my SD card that has a half-dozen boot animations in it, allowing me to choose which one I'd like to use.
If you need to download ES Explorer, there are a few options you'll need to enable to be able to manipulate the local filesystem. They are "Root Explorer" and "Mount File System" I think it goes without saying, but you'll need to grant ES Explorer with root permissions when prompted.
WARNING: If modifying your file system like this, BE CAREFUL what you delete. Delete the wrong file, and you could be starting over. I am not responsible for you bricking your phone.
I believe bdogg is referring to the boot splash screen. If you are following the directions that I think you are, I have not yet been successful at getting it to work yet either . If you figure it out let me know.
Sent from my SCH-I500
It is quite possible that I misunderstood which screen it was he was wanting to change. On my phone, all I get during the boot sequence is the black & white "Samsung" screen twice (once when the phone first powers on, and then it flashes quickly and reappears for what I assume is the Glitch kernel), and then the AOKP Unicorn boot animation. Once the Unicorn boot animation finishes, I get the unlock screen, at which point I consider the boot process finished. To my knowledge, you can't change the B&W Samsung screen. I could very much be wrong here, I've just never seen anything stating differently. The Glitch "logo" is set in the kernel, although I'm guessing if you edit the right thing in the .zip before you flash it that could be changed. It's not something I care to attempt, it's not on screen long enough for me to really care, and I have no preference to go messing around in the kernel. That leaves the Unicorn boot animation, which I know can be quite easily changed out to whatever different boot animation you prefer.
I'm currently running AOKP Build 28 with Glitch 14 B6.
EDIT: After a quick Google search, it appears I am wrong and that it is possible to edit the default "Samsung" screen. I didn't fully read up on the process, as I don't care to do it myself, but I did glean enough to know that I probably posted instructions here to something that you already knew, and that didn't help you one bit. I'll do better next time.
Yes, we are talking about the initial samsung logo. It is fun to change it to other things i admit. I only was able to do it per the instructions on the gb roms. I thought I saw new ones for ics but can't remember where I saw them.
Sent from my SCH-I500
Related
I seem to be at a bit of a cross road here, hopefully posting this story can give me some direction, as I see people with similar problems elsewhere, but not on XDA.
After getting the JI6 upgrade on stock, it took out OCLF, when i did it update, none of the setting where available. So when I redid OCLF, i could not up to the new OCLF and could not undo the old one. However voodoo5 was available, and seeing the reports on that voodoo5 was the bees knees. So I ran it (stupidly. It went though the motions, heard the voice prompts saying the steps, and said it was Completed. I knew the first boot up took some- what I would get is
Stuck on Black Vibrant screen, would hear T-Mo boot up sound, but would never progress after 20 - 30 minutes
Reading the Forum, (Use that search button) using the steps specifically in this post: [TUTORIAL][ROM] How to fix your phone and apply the update --- to achieve what i heard that had success stories with using Odin to restore to restore JI6 update after this kind of error. Well here is where I am at:
I can get into recover mode and boot loader
I get Vibrant, Tmobile screen, hear the tmobile tone, and then see the galaxy S screen
I then get an all black screen where the buttons on the bottom (home, back etc) light up, and will turn off when i touch them and then come back on
And that's it. I get nothing, a big blank screen. And I am unsure where to go... any advice would be helpful on how to get a full recovery. No longer worried about my data, just want to get my phone back up and running by any means.
buggzero said:
I seem to be at a bit of a cross road here, hopefully posting this story can give me some direction, as I see people with similar problems elsewhere, but not on XDA.
After getting the JI6 upgrade on stock, it took out OCLF, when i did it update, none of the setting where available. So when I redid OCLF, i could not up to the new OCLF and could not undo the old one. However voodoo5 was available, and seeing the reports on that voodoo5 was the bees knees. So I ran it (stupidly. It went though the motions, heard the voice prompts saying the steps, and said it was Completed. I knew the first boot up took some- what I would get is
Stuck on Black Vibrant screen, would hear T-Mo boot up sound, but would never progress after 20 - 30 minutes
Reading the Forum, (Use that search button) using the steps specifically in this post: [TUTORIAL][ROM] How to fix your phone and apply the update --- to achieve what i heard that had success stories with using Odin to restore to restore JI6 update after this kind of error. Well here is where I am at:
I can get into recover mode and boot loader
I get Vibrant, Tmobile screen, hear the tmobile tone, and then see the galaxy S screen
I then get an all black screen where the buttons on the bottom (home, back etc) light up, and will turn off when i touch them and then come back on
And that's it. I get nothing, a big blank screen. And I am unsure where to go... any advice would be helpful on how to get a full recovery. No longer worried about my data, just want to get my phone back up and running by any means.
Click to expand...
Click to collapse
Did You Flash Something Before Disabling Voodoo? 2 Fixes to Help You Out.
So you forgot to disable the voodoo lagfix before you flashed a new rom and now you're getting an error, similar to the one posted below. Even Odin won't allow you to flash back to stock. Well, pay close attention and with some luck, you'll be good as rain...or something like that.
Fix 1:
1. Download Eugenes 'Froyo that does not brick' file.
2. Extract the files.
3. Open Odin, plug in your phone, then put it into download mode.
4. load the PIT file in appropriate area.
5. load the .tar file in the PDA area.
6. DO NOT check 're-partition'.
7. Click start, let it finish. Your phone will load and reboot into stock recovery. It will error out again. DONT panic! This is what's supposed to happen.
8. Now, pull your battery.
9. Download the 'True stock 2.1 firmware for the vibrant'.
10. Extract the files.
11. Once again, open Odin, plug in your phone, put into download mode.
12. Load the PIT file into the appropriate area and the .tar in the PDA area.
13. THIS TIME you want to check the 're-partition' box.
14. Now click start, let it finish, and this time your phone will load up just fine! BAM!
Fix 2: (use only if you know how to use adb commands)
1. Place the 'disable-lagfix' file in your sdk>tools directory
2. Get into clockwork recovery like you normally would
3. Follow these adb commands to push the 'disable-lagfix' file to you sdcard>voodoo
adb push disable-lagfix /sdcard/voodoo
4. File should now be on your sdcard in your voodoo folder.
5. Reboot phone and with luck, you should hear Linda the robot telling you your file system is being converted back to rfs.
6. Because your system directory has already been wiped, you'll still get a black screen when you reboot, but your file system is back to rfs. Just pull the battery, and reflash whatever rom you want. Then reboot again.
ANNNDD THE TRUUUUTHHH SHALL SET YOU FREEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE
Thank you AMD. Following "Fix 1" Method, worked flawlessly!
Now, just to clarify, this put the phone completely back to stock? It has undone the ext2, voodoo and hoodoo nonsence? I just want to know where I stand, becuase now that I am wiped clean, there is obvious no worry of loosing data now lol. Might as well put a nice custom rom, rather than fiddiling with fixes to the stock right now.
Also, I am not yet familiar with ADB, but will read the sticky Bible thread, do you recomend that method over the 1st one? I did not install clockwork recovery, is that a perferred pre-loader to prevent these kind of issues?
buggzero said:
ANNNDD THE TRUUUUTHHH SHALL SET YOU FREEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE
Thank you AMD. Following "Fix 1" Method, worked flawlessly!
Now, just to clarify, this put the phone completely back to stock? It has undone the ext2, voodoo and hoodoo nonsence? I just want to know where I stand, becuase now that I am wiped clean, there is obvious no worry of loosing data now lol. Might as well put a nice custom rom, rather than fiddiling with fixes to the stock right now.
Also, I am not yet familiar with ADB, but will read the sticky Bible thread, do you recomend that method over the 1st one? I did not install clockwork recovery, is that a perferred pre-loader to prevent these kind of issues?
Click to expand...
Click to collapse
Your welcome and yes, you're completely back to stock and everything is gone. So you should be set. No, both methods work well and do the same. I know adb but still prefer the first method, works all the time is something goes wrong with voodoo or any lagfix.
I wouldn't say it's preferred to prevent those issues because you may still have them either way but its nice to have. You can make a backup with it so if anything goes wrong you have something to fall back on. Just makes things simpler.
Sent from my SGH-T959 using XDA App
Seeing some of your other posts in the bionix fusion rom, which is what I ended up flashing to, it seems that the issue you had mentioned is that even if your moving between voodoo compatible roms, voodoo needs to be removed before.
This can be done within the handset with rom manager, using the voodoodisable.zip?
Cause ya, didn't quite understand that part till it happened. Feel pretty dumb when there is post after post of "PPL DUN FKN READ"
Sent from my SGH-T959 using XDA App
buggzero said:
Seeing some of your other posts in the bionix fusion rom, which is what I ended up flashing to, it seems that the issue you had mentioned is that even if your moving between voodoo compatible roms, voodoo needs to be removed before.
This can be done within the handset with rom manager, using the voodoodisable.zip?
Cause ya, didn't quite understand that part till it happened. Feel pretty dumb when there is post after post of "PPL DUN FKN READ"
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
It's simple to disable voodoo. When you have voodoo installed you should have a voodoo folder in your internal SD card, if you don't them make one. Put a file called disable-lagfix in there with no extensions. A blank file with that name. Reboot and you'll hear the.process going through of removing voodoo. Then you can flash what ever you like without any problems. If you want voodoo back delete the disable-lagfix file or rename it to enable-lagfix. Simple.
Sent from my SGH-T959 using XDA App
thx for ur sharing...
i hv the same problem, it's fixed now...
I'm having a little trouble and I'm sincerely hoping you'll help. I've tried flashing my Eris using the file, "Evil_Tazz_3.zip" and my Eris is now bricked and stuck in a bootloop. All it will do is show an animation of the sketchy letters ANDROID falling down the screen and then a smoky light following close behind it reveling the Droid itself. And it'll repeat this animation rapidly about 100 times before freezing and then restarting the whole process all over. To be frank it pisses me off because it always seems that I'm the only one who has trouble with this stuff.
My Eris is rooted and it does allow me to access the recovery screen. What am I supposed to do?
Anyways, thanks for your time.
Best Regards -Joseph Bergen
jbergen said:
I'm having a little trouble and I'm sincerely hoping you'll help. I've tried flashing my Eris using the file, "Evil_Tazz_3.zip" and my Eris is now bricked and stuck in a bootloop. All it will do is show an animation of the sketchy letters ANDROID falling down the screen and then a smoky light following close behind it reveling the Droid itself. And it'll repeat this animation rapidly about 100 times before freezing and then restarting the whole process all over. To be frank it pisses me off because it always seems that I'm the only one who has trouble with this stuff.
My Eris is rooted and it does allow me to access the recovery screen. What am I supposed to do?
Anyways, thanks for your time.
Best Regards -Joseph Bergen
Click to expand...
Click to collapse
Whatever you do, DO NOT DO ANYTHING ELSE UNTIL BTFB0 responds to your plea for help.
Do not just start trying different solutions, DO NOT FLASH ANY RUU, if you know what that is. BTFB0 is the guy who can get your phone unbricked if anyone can. He is the expert, I won't pretend to be able to duplicate his knowledge in this area.
Be patient until he has a chance to see this. You don't have to PM him, I'm sure he'll respond when he has a chance here in public. He will ask specific questions about what version of bootloader you have, 1.47 or 1.49, and you might as well find out if it's S=OFF or S=ON.
Also, do you have Amon RA recovery on your phone and can you get to it?
Have you tried flashing anything else since your phone has gotten stuck in this boot loop? If not and you can get into recovery still, then simply wipe data, wipe dalvik, and try flashing again. Don't worry you're phone doesn't sound bricked, just like you got a bad download or an error when flashing the rom. I would probably try a different rom or at least re-download the one you want to use.
It may still be wise to wait for BTFB0 to get here and offer some more advice as I am sure he has more knowledge in this area than me. But I do feel confident that he will say the same thing as I have.
Well, the OP merely said that he is having trouble with a specific ROM; he didn't mention failures during flashing; so, his problem could be as simple as having failed to "wipe" before flashing his ROM.
jbergen:
If you can boot into a custom recovery, your phone is not "bricked". It's not even soft-bricked; it's just not booting into the main OS correctly.
Providing as much detail as you can is helpful to people that are offering help to you; in particular, the following pieces of information:
- What recovery is on your phone? (Amon_RA, Clockwork? What version #?)
- When you are flashing the ROM file with your recovery, do you notice any "E:" messages?
An "E:" at the beginning of a line on the screen means that an error occurred!
- Are you having this same trouble on more than one ROM, or is this the only ROM you have tried since you rooted?
- What method did you use to root the phone?
- Did you use the "Wipe data/factory reset" menu item before you flashed the ROM file?
- Did you make any Nandroid backups that you still have on your SD card? If yes, did you attempt to restore one? What was the result? (BTW, every rooted phone user should be making Nandroid backups before they flash ROMs - no exceptions.)
- Do you have a media card slot or USB card reader device that will allow you to copy a different ROM file onto your SD card? -OR-
- Do you know how to "mount" the SD card onto the PC when your recovery is booted? (On Amon_RA, it is called "Toggle MS-USB" or something like that; it's also in the Clockwork menu somewhere too)
Given the information you have provided, there are any number of things that could be going on. I would suggest downloading a different ROM to your PC (let's say the stock HTC Eris March 2011 ROM), and then transferring it to your SD card. Then,
- Verify the exact size of the file and/or MD5 signatures of the file (if the developer provided it).
- make sure your phone is well charged
- perform a "Wipe data/factory reset" from the recovery menu
- Flash the ROM file from the recovery menu - and pay attention to the screen to see if there are any `E:' errors
- If there are errors, there is no point in attempting to boot the phone
- If there are no errors, boot the phone.
- Report your results here - and answer the questions that I asked.
Girlfriend got a Fascinate yesterday and deemed me worthy enough to root it so she can kill all the bloatware (yay for me!). I've got root on the phone, and I understand that if I don't flash a custom kernel for the phone, it'll just break the recovery (using "cwm-recovery-all.tar") as soon as the phone boots up. She likes the overall touchwiz experience and all that, so I'm not sure of any rom's that are pretty stock cept for bloat, and any kernels I should use so recovery doesn't break.
I'm just concerned about getting recovery to stick so that I can perform a backup in case anything should happen.
I have a OG Droid, so all this bending over backwards for root and recovery is new to me and threads seem either too full of info or not enough for me, so here's me asking for help!
Either way, thanks!
Dustin
seraph_harim said:
Girlfriend got a Fascinate yesterday and deemed me worthy enough to root it so she can kill all the bloatware (yay for me!). I've got root on the phone, and I understand that if I don't flash a custom kernel for the phone, it'll just break the recovery (using "cwm-recovery-all.tar") as soon as the phone boots up. She likes the overall touchwiz experience and all that, so I'm not sure of any rom's that are pretty stock cept for bloat, and any kernels I should use so recovery doesn't break.
I'm just concerned about getting recovery to stick so that I can perform a backup in case anything should happen.
I have a OG Droid, so all this bending over backwards for root and recovery is new to me and threads seem either too full of info or not enough for me, so here's me asking for help!
Either way, thanks!
Dustin
Click to expand...
Click to collapse
You're just a few steps away.
First download this stock ed01 debloated/debinged stock ROM from link below and place in root directory of SD card:
http://www.multiupload.com/BKHF5DKJ18
also, choose a kernel and place on sd card. I recommend imnuts' PB&J variety-you might want to stick with stock voltage or -50uv for now. Be mindful to get non-voodoo if you aren't planning on getting into this. found here (try the 3rd or 5th option):
https://sites.google.com/a/imnuts.net/android/kernels
Next, use Odin to install your CWM again. When you boot up this time, boot directly into CWM by turning phone off, and holding volume down, volume up, and power (all 3) until CWM appears. flash your rom, and kernel. If you don't boot into cwm directly by this method, the stock kernel will overwrite CWM, which is what was happening to you, i believe.
after rom/kernel is installed, choose reboot system now from cwm.
Yeah, I just wasn't sure about what kernel would be good for her phone, so I just was kinda "stuck" at that point. ^^;;
But I will give it a go and she how it works out! thanks much!
Everything was a success, and there was much rejoicing!
They only thing I noticed was after the Samsung bootloop animation, it goes to the default "android" one instead of Verizon's... I'm sure there's a way to get that back, but its not in the system dump I have. I'm currently searching for it on the net ^^;;
Thanks again!
Edit: I was able to find a boot animation that had the first part of the Galaxy S bit without the Verizon part. When it booted it just repeated the "Galaxy S" animation. I thought by adding, renaming, and reversing the shutdown animation would at least give that back, but now I just get a black screen for that segment...Still working on it....I think it has to do with the txt file inside, but i'm not sure.
The PowerOn.wav is still present on the phone, but it doesn't play either.... >_<
Are you certain you put poweron.wav in /system/etc folder?
Yup, its there and plays fine in the media player, but I just noticed that there's also a PowerOn.snd file right above. Could that be interfering?
Make a backup elsewhere of that file, then delete it and see if that works.
Sent from mah Fascinate using XDA Premium App
The sound won't work with most kernels that are not stock because the boot sounds aren't actually turned on in the kernel
Swyped from my CM7 fascinate
Oh okay, any chance to get the default boot animation from any of you guys? She doesn't mind the sound "missing," but she would like the boot animation at least.
Eitiher way, thanks much for the info!
since it seems like you're using a stock Rom just debloated and rooted, you may want to think about just using the stock Kernel with the recovery wipe removed, it has two options one that sticks with the stock boot animation and may still have sound and one that allows custom boot animations. This kernel was created by imnuts and can be found here:
http://forum.xda-developers.com/showthread.php?t=1060457
Awesome, thanks! I'll give that a try and see how it turns out!
And it worked! Thanks again!
Is there a link to explain how to delete or change the stock start up pink screen on the T959 Vibrant? I hate it.
Root the phone then put download Rom Manager and titanium backup. The download a custom rom and flash that....... you will never see the pink screen again.
You need to read more, alot more.........
WHAT ????
ya ya ya done all that , done all the reading, done a lot of roms, done a lot of rooting ........
your assumption is "all" rom make new boot screens I guess?????
guess not. go load Project_V & see what I'm talking about.
i'm looking for answers, not rebukes.
Never been on Project V and i dont even remember stock but theres 3 startup images usually ~Bootloader,kernel,bootanimation. I doubt its bootloader
If its Bootanimation is located in /system/media/bootanimation.zip just swap for something else or put "debug.sf.nobootanimation=1" in build.prop for no boot animation at all
Or it might be the kernel boot picture, change kernels since i dunno where kernel image is stored, Bullet is good
Root rom boot animation.
sent from my Sensation XD
replace the boot animation. and delete the shutdown animation. thats what i did. im currently on project v.
Sent from my Vibrant
Hi,
I have a S II with a custom Jelly Bean ROM. I recently did a simple change to the build.prop file, just added some info lines, I am sure they are harmless in sense of not doing a significant change to the phone operation. The thing is that when I reboot the phone, it does not reach the launch screen, kept stuck on the boot animation. The same happen when I modified just another system file (media_profiles.xml on /system/etc) the same behavior happen.
Is there some kind of protection validation or check-sum checking on boot process that if not pass it will not boot the phone ? Even when I revert back the original files and set the appropriate file permissions, it still does not boot. I basically have to install my current ROM without wiping and everything comes back fine.
I really appreciate any information on this.
Thanks.