[Q] 2.17 ruu, 1.50h boot downgrading problem

[Q] 2.17 ruu, 1.50h boot downgrading problem - HTC EVO 3D

Hello all,
Ultimately , I am trying to downgrade my 1.50 hboot via the method on HTCEvoHacks . I cannot temp root via their method however, because I a have 2.17 ruu installed. They recommended to just use taco root. When I try taco, it boots to recovery , but I get a red triangle. In fact , when I press "recovery" from hboot, I get the same issue. I have completely re-flashed the stock 2.17 RUU with full data wipe, still same problem.
I must be missing something here, would appreciate your help
thanks

By the way I used zergrush it works better. Also if you want to go to 2.08 do the first part of unknowns thread that's about the mainver downgrade in adb then run the 2.08 ruu exe and you are all good. Start from beginning. I couldn't get the 2.17 as PG86IMG to stick until I used the one in the tools thread. But ya zergrush man
Sent from my BAD A$$ EPIC TOUCH 4G

patrao_n said:
By the way I used zergrush it works better. Also if you want to go to 2.08 do the first part of unknowns thread that's about the mainver downgrade in adb then run the 2.08 ruu exe and you are all good. Start from beginning. I couldn't get the 2.17 as PG86IMG to stick until I used the one in the tools thread. But ya zergrush man
Click to expand...
Click to collapse
Thanks patrao, will do. However, I cannot change mainver since I must have temp root. I cannot use the zergRush temp root method (meant for 2.08) , so the only way is to tacoroot. I cannot succesfully finish taco because the phone crashes right at recovery. Red triangle. Is it possible my recovery is corrupted in some way ? Like I said, I flashed a fresh copy of 2.17, including recovery. Not sure what would crash recovery in that way.
Any help much appreciated .

tacoRoot
when you open root.bat in the tacoRoot folder, after it does its thing itll show hold down power button, volume up, and volume down but all at once and when it reboots to recovery you'll be fine. my only problem is after that part and doing the mainver commands, i put the pg86IMG.zip in my root of my sd card, and it wont find it. it checks for it but doesn't find it.

Ok, Vol Up/Down and Power got me to the Recovery options. Had tried it before, but did not work for some reason.
patrao, I did change over to 2.08, and proceed with zergRush , thank you.
However, I currently have phone bricked, but I cannot get the 1.40 flash going. When I insert bricked phone into Ubuntu (virtual box) , both Win and Ubuntu report a non-android USB. The driver reads Qualcomm I believe, and I suppose this is why it cannot find device and flash.
Any hints to recognize the device once bricked ?
thank you .

daliatre said:
Ok, Vol Up/Down and Power got me to the Recovery options. Had tried it before, but did not work for some reason.
patrao, I did change over to 2.08, and proceed with zergRush , thank you.
However, I currently have phone bricked, but I cannot get the 1.40 flash going. When I insert bricked phone into Ubuntu (virtual box) , both Win and Ubuntu report a non-android USB. The driver reads Qualcomm I believe, and I suppose this is why it cannot find device and flash.
Any hints to recognize the device once bricked ?
thank you .
Click to expand...
Click to collapse
If you study this thread, it looks like you are now ready to do Step 3:
http://forum.xda-developers.com/showthread.php?t=1547695

Success. Thank you all for your help.
I had to run Ubuntu on its own. VirtualBox / Win does not recognize the phone once bricked .

Finally got mine from 1.5-1.4. Took some stressful hours but finally got it to work.....now have s-off
Sent from my PG86100 using xda premium

Related

root evo 3d hboot 1.5 help?

i have tried everything possible with this phone to root it and nothing. Was wondering if someone would help me out??

I feel your pain and I've try the HTC dev. unlock with no luck I'm coming from the OG evo which was really easy to root ..
Sent from my PG86100 using XDA Premium App

go to htcevohacks.com i hace hboot 1.5 and it worked perfectly if u have the newest upgrade tho i dont think they have a root method out yet

Htcevohacks is easiest . And with the newest ota its still hboot 1.5
Sent from my PG86100 using XDA App

brandonaspencer said:
i have tried everything possible with this phone to root it and nothing. Was wondering if someone would help me out??
Click to expand...
Click to collapse
It would help us if you told us exactly what problems you are having.

Cool!! thanks!!
Sent from my PG86100 using XDA Premium App

Look at the roll up stickies. The directions are pretty clear. HTC method is going to be your only option
Sent from my Galaxy Nexus using XDA App

Rooting phone
brandonaspencer said:
i have tried everything possible with this phone to root it and nothing. Was wondering if someone would help me out??
Click to expand...
Click to collapse
have kinda problems have you had with rooting your phone.

HTC evohacks is very easy thanks !! For the help : )
Sent from my PG86100 using XDA Premium App

yami951 said:
Look at the roll up stickies. The directions are pretty clear. HTC method is going to be your only option
Sent from my Galaxy Nexus using XDA App
Click to expand...
Click to collapse
I agree
Sent from my PG86100 using xda premium

Trying to root using HTC 1.5 with no success.
Hi to all I have tried to root using the HTC boot unlocker with no success. I was using the step by step instructions from HTC evo hacks. I got to the step at the command prompt where I put in the unlock code and I got this : C:\rootevo3dnew>fastboot flash unlocktoken Unlock_code.bin
sending 'unlocktoken' (0 KB)...
OKAY [ 0.152s]
writing 'unlocktoken'...
(bootloader) unlock token check successfully
OKAY [ 0.007s]
finished. total time: 0.161s
The phone screen asking me to unlock the bootloader never came up. Any help would be appreciated. BTW I have rooted at least 7 EVO 3D's. with no problems.
I'm stumped.

lilal100 said:
The phone screen asking me to unlock the bootloader never came up. Any help would be appreciated. BTW I have rooted at least 7 EVO 3D's. with no problems.
Click to expand...
Click to collapse
See the Guide/flashing Notes in my signature. You need to rerun the currently installed "FULL" Ruu or the the Latest RUU, then the unlock will work.

I did the HTCDev and unlocked it went to thread on downgrade from 1.5 hboot to 1.4 tried that and it did not work. I went to try the wire trick and this is what I get when I try to use the controlbear. the phone connects and goes through process but says the following...
======== ControlBear 0.6 beta for JuopunutBear S-OFF ==========
Starting up......
Connecting to device...
Searching device.....
Found device.....but device has no root!!
Press ENTER to exit.....
Any help would be helpful I have tried superuser but wont install, tried rootevo3dnew, temproot sensation Ect. everything says I need to be rooted.
I am running stock rom that shipped with phone and yes I did updates. I am Sprint CDMA 2.17 rom shipped, 1.5 Hboot. I have flashed roms and modded before but dont consider myself to be advanced. I have done flashing and installing roms with my old HTC Touch pro2 but alot easier on touch pro2 LOL... Please point me in the correct place I have beeen all over from this thread to that one and back and forth and yes I have search threads and I have tried them but still come back to the one with wire trick.. I am 1.5 with S-ON

inkjammer said:
I did the HTCDev and unlocked it went to thread on downgrade from 1.5 hboot to 1.4 tried that and it did not work. I went to try the wire trick and this is what I get when I try to use the controlbear. the phone connects and goes through process but says the following...
======== ControlBear 0.6 beta for JuopunutBear S-OFF ==========
Starting up......
Connecting to device...
Searching device.....
Found device.....but device has no root!!
Press ENTER to exit.....
Any help would be helpful I have tried superuser but wont install, tried rootevo3dnew, temproot sensation Ect. everything says I need to be rooted.
I am running stock rom that shipped with phone and yes I did updates. I am Sprint CDMA 2.17 rom shipped, 1.5 Hboot. I have flashed roms and modded before but dont consider myself to be advanced. I have done flashing and installing roms with my old HTC Touch pro2 but alot easier on touch pro2 LOL... Please point me in the correct place I have beeen all over from this thread to that one and back and forth and yes I have search threads and I have tried them but still come back to the one with wire trick.. I am 1.5 with S-ON
Click to expand...
Click to collapse
Ok, let's make sure we know where you are at to start with. When you use the vol and power button to boot to fastboot, does the phone show "unlocked". If not, I think you need to do the htc method again. I have not kept up recently, but I am not sure there is any method other than the HTC method that works every time for 1.5. I have used the HTC method on two phones without a problem, so that is the method I use.
Once you get that far, I used adb to push or flash the twrp image into the recovery section of the phone. Then you should be able to flash superuser via the install menu of twrp. There are threads that have detailed explanations on how this is done.
Yea, I had a bit of a learning curve from my TP2 also, but love this phone!

sonza said:
Ok, let's make sure we know where you are at to start with. When you use the vol and power button to boot to fastboot, does the phone show "unlocked". If not, I think you need to do the htc method again. I have not kept up recently, but I am not sure there is any method other than the HTC method that works every time for 1.5. I have used the HTC method on two phones without a problem, so that is the method I use.
Once you get that far, I used adb to push or flash the twrp image into the recovery section of the phone. Then you should be able to flash superuser via the install menu of twrp. There are threads that have detailed explanations on how this is done.
Yea, I had a bit of a learning curve from my TP2 also, but love this phone!
Click to expand...
Click to collapse
I am unlocked I did the HTC Dev and unlocked it. I have a stock rom (the one shipped on phone) all I have done is unlock it... I did try the controlbear and got what I posted on last post. I am Hboot 1.5 S-ON and stock rom is 2.17.651.5 HTC Sense 3.0 ANDROID Ver. 2.3.4... Like I said all I have done is Unlock and installed TWRP 2.2 and created a restore point and created a recovery and backed up my phone. All through Goo Manager. That is all I have done.

inkjammer said:
I am unlocked I did the HTC Dev and unlocked it. I have a stock rom (the one shipped on phone) all I have done is unlock it... I did try the controlbear and got what I posted on last post. I am Hboot 1.5 S-ON and stock rom is 2.17.651.5 HTC Sense 3.0 ANDROID Ver. 2.3.4... Like I said all I have done is Unlock and installed TWRP 2.2 and created a restore point and created a recovery and backed up my phone. All through Goo Manager. That is all I have done.
Click to expand...
Click to collapse
In my post Ive included a flashable SuperSU zip. What youll need to do is boot to recovery and install this zip. Then reboot. You should have superuser access then.

Still learning this forum so excuse any errors I make. I've spent the last 10 hours trying to fix the mess I created on my wife's Evo 3d. I was able to root my phone and it was relatively easy so I tackled hers as well and have gotten a bootloop I cannot figure out, 10 hours later. I'm on hboot 1.5. I unlocked the phone (using a pretty reliable video), loaded 4EXT Recovery then tried to load roms. Everything worked fine until the rom-loading portion. Since then, the phone loops, but once or twice it made it all the way to the main screen and before I could slide the ring, a read error message appeared next to the bars of service then the phone just completely reboots. Right now, the only thing I can get into is the bootloader and the clockworkmod v4.0.1.4, somehow I lost my 4EXT Recovery. I'm stuck and in dire straights as my wife is going out of town and will KILL me if I don't fix her phone. Please help! BTW, somehow I managed to NOT back anything up (stupidity on my part). Will I be able to get this thing back to stock at least or is it now a paperweight?

user22410 said:
Still learning this forum so excuse any errors I make. I've spent the last 10 hours trying to fix the mess I created on my wife's Evo 3d. I was able to root my phone and it was relatively easy so I tackled hers as well and have gotten a bootloop I cannot figure out, 10 hours later. I'm on hboot 1.5. I unlocked the phone (using a pretty reliable video), loaded 4EXT Recovery then tried to load roms. Everything worked fine until the rom-loading portion. Since then, the phone loops, but once or twice it made it all the way to the main screen and before I could slide the ring, a read error message appeared next to the bars of service then the phone just completely reboots. Right now, the only thing I can get into is the bootloader and the clockworkmod v4.0.1.4, somehow I lost my 4EXT Recovery. I'm stuck and in dire straights as my wife is going out of town and will KILL me if I don't fix her phone. Please help! BTW, somehow I managed to NOT back anything up (stupidity on my part). Will I be able to get this thing back to stock at least or is it now a paperweight?
Click to expand...
Click to collapse
Your not bricked by any means. And Im going to guess you tried to boot an ICS rom.. dont. They dont work with hboot 1.5. If you really want to go back to stock run the 2.17 RUU and youll be back to where you started. Another option is to download a GB rom and flash that. Not ICS. If your able to get to the bootloader than you can still load up 4ext recovery so you can flash the GB rom.
Edit: some hboot 1.5 users are lucky and can flash them if they used the correct VM firmware but majority of users have problems.

NineInchNails said:
Your not bricked by any means. And Im going to guess you tried to boot an ICS rom.. dont. They dont work with hboot 1.5. If you really want to go back to stock run the 2.17 RUU and youll be back to where you started. Another option is to download a GB rom and flash that. Not ICS. If your able to get to the bootloader than you can still load up 4ext recovery so you can flash the GB rom.
Edit: some hboot 1.5 users are lucky and can flash them if they used the correct VM firmware but majority of users have problems.
Click to expand...
Click to collapse
Thanks, I just tried flashing a rom that has taken it back to stock but I'm still in the bootloop. Should I stop flashing and simply locate the RUU?

22410,
It sounds like the kernel did not flash correctly with 4ext Recovery (next time, make sure u indicat S-on in its settings). I'm not sure if you were just stock 2.17 rooted or not, but use 7zip on your pc to open & extract/copy out the "boot.img" file from the rom, zip, etc you were using and copy it to your fastboot pc folder. Still have the Cwm 4.0.1.4 recovery.IMG file there too right (or the 4ext recovery.img file)? Ok...
- put phone in fastboot usb mode
From PC's fastboot command prompt type:
- " fastboot flash boot boot.img "
(this will reflash the kernel/boot image extracted from a rom)
If your recovery is screwed up:
- " fastboot flash recovery YourRecoveryFilename.img "
(ie: cwm_4.0.1.4_recovery.img or recovery.img, etc as listed in fastboot folder, to reflash a recovery to your phone).
With S-on, to properly enter a recovery for flashing ANYTHING you must:
- " fastboot boot YourRecoveryFilename.img "
(doesn't apply if using 4ext's Smartflash or TWRP's Dumlock settings. But you must have a bootable android OS/kernel first, once the flash is screwed it won't work).
If u have a Sprint CDMA EVO3D/HTC Unlocked & S-on (not Jbear s-Off), then the guide in my signature has more info.
Edit: as NIN said you will likely have problems flashing ICS roms with S-on (hboot version doesn't matter). If u are still unlocked & have a working recovery u can flash any gb Rom successfully after wiping system, data, & cache (or run superwipe zip). Meanrom GB v4.5 recommended.
Sent from my "Up all night, Sleep all day" EVO3D!

[Q] [q] how do I unbrick an amaze that wont go into recovery?

Backstory: I tried flashing android revolution for the amaze once, and it didn't work (error 1) left it alone for a bit after recovering it, went back to bulletproof and flashed faux .009 kernel, then decided to try again...
Well I'll try to make this brief, sorry if I'm posting in the wrong subforum but here goes, I tried going from bulletproof 2.5.0 to Android Revolution HD and didn't flash the superwipe .zip (lazy me). The install failed with the same error 1, only this time I can't boot back into recovery. Booting to bootloader works but when I tried going into recovery I see it pop up for maybe a fraction of a second before the phone reboots.
I've tried reflashing clockwork mod but no dice
any sort of tips you folks can give me to steer me in the right direction?

Pulsewave said:
Backstory: I tried flashing android revolution for the amaze once, and it didn't work (error 1) left it alone for a bit after recovering it, went back to bulletproof and flashed faux .009 kernel, then decided to try again...
Well I'll try to make this brief, sorry if I'm posting in the wrong subforum but here goes, I tried going from bulletproof 2.5.0 to Android Revolution HD and didn't flash the superwipe .zip (lazy me). The install failed with the same error 1, only this time I can't boot back into recovery. Booting to bootloader works but when I tried going into recovery I see it pop up for maybe a fraction of a second before the phone reboots.
I've tried reflashing clockwork mod but no dice
any sort of tips you folks can give me to steer me in the right direction?
Click to expand...
Click to collapse
Not sure about the Amaze tbh, but if I had a failed flash on either of my HTC phones, I just re RUU'd.

D'oh! I forgot about that! Had to do that for my buddy's thunderbolt a few times. Lemme give that a shot and I'll report back
Edit: Worked

Edit:double post

im also having this problem, my phone keeps freezing at the startup screen when the htc logo pops up. i dont know much about this kind of stuff so i would really appreciated if anyone could guide me to what to do
the way that my phone froze like that was that i tried to flash a kernel for the Energy rom, i did installed the rom itself
http://forum.xda-developers.com/showthread.php?t=1362759 this is the rom that i wanted to use
and i flashed the kernel that was provided in the 4th post, i downloaded that file, extracted and ran the .bat file and thats how it happened
i would appreciate if anyone could help me with this

Bricked Htc Amaze 4g
I have a bricked HTC Amaze 4g. I had beastmod v2.20 on when i decided i wanted quick sense. After i finished it just froze on the htc startup logo. I played with it and got it into a bootloop. When i try to flash a ruu the blue bar loads up and comes back to the bootloader screen. I can get into recovery but it wont let me flash anything.Thanks to whoever replies I really appreciate it.

lmfaoomg said:
im also having this problem, my phone keeps freezing at the startup screen when the htc logo pops up. i dont know much about this kind of stuff so i would really appreciated if anyone could guide me to what to do
the way that my phone froze like that was that i tried to flash a kernel for the Energy rom, i did installed the rom itself
http://forum.xda-developers.com/showthread.php?t=1362759 this is the rom that i wanted to use
and i flashed the kernel that was provided in the 4th post, i downloaded that file, extracted and ran the .bat file and thats how it happened
i would appreciate if anyone could help me with this
Click to expand...
Click to collapse
You need to superwipe the phone and flash the ROM. After the ROM flashes, you have to flash the kernel twice.
samiaziz said:
I have a bricked HTC Amaze 4g. I had beastmod v2.20 on when i decided i wanted quick sense. After i finished it just froze on the htc startup logo. I played with it and got it into a bootloop. When i try to flash a ruu the blue bar loads up and comes back to the bootloader screen. I really appreciate it.
Click to expand...
Click to collapse
Same with you. You need to superwipe the phone and flash the ROM. After the ROM flashes, you have to flash the kernel twice.
Superwiping the phone removes all the data from the old ROM so you can install a fresh clean ROM.
If you want to install the RUU, you have to relock the bootloader first and then you can reflash the original RUU

Edit: i was misinformed
Sent from my NRGized Amaze...
via xda premium

aj_2423 said:
I dont believe u have to relock
Sent from my NRGized Amaze...
via xda premium
Click to expand...
Click to collapse
To flash an official RUU, you must relock it. I've done so plenty of times lol
Sent From My HTC Amaze 4G via Someone's Room

If the phone wont go into recovery, you have to use ADB and wipe the cache partition for it to go into recovery again. This is apparently a bug with some of recoveries posted by other devs in the development forum. You need to use fastboot.exe to wipe the cache via adb

And if... If the superwipe doesn't work due to recovery version you have try to boot in to your Bootloader run one of hasoon's tool and choose different recovery.. it did happen to me the bootloop before due to the fact the old roms like mike's rom. he doesn't update his script to support the newer recoveries and it doesn't support X's recovery, it will give you an error installation.. just try different recoveries and for sure your problem will be solved..
just make sure boot in your bootloader/H-boot then run hasoon's tool and have enough battery just to make sure...

hasoon2000 said:
To flash an official RUU, you must relock it. I've done so plenty of times lol
Sent From My HTC Amaze 4G via Someone's Room
Click to expand...
Click to collapse
Thanks for the good info Sir but i my HTC Amaze is bootloader locked and S-ON but i cannot find a RUU for T-mobile to unbrick it. Will a Ruu such as this one work?
RUU_Ruby_Videotron_CA_1.46.1530.1_R2_Radio_1.09.550L.17DC_30.68.550L.09_release_227343_signed.exe
My HTC Amaze scans all the versions of the PH85IMG i place on the sd card but goes back to the menu when its down
any advice that could help i will appreciate!

There's a thread in the dev section that has about a dozen RUUs. I don't see how one can miss it.

Thanks for your reply but i was a little unsure and did not want to make my phone any worst than it already is.
Can you explain 1 thing thing for me please - RUU always you to flash the phone via the computer? where as PH85img.zip allows you to flash the phone via sdcard? I hope i am correct here.
but i want to know how can i flash the phone when its connected via HBoot usb cause my pc recognizes it as "Android Composite ADB Interface"
Currently this is what is on my lcd
LOCKED
RUBY PVT SHIP S-ON RL
HBOOT-1.93.0002
EMMC BOOT
MAR 15 2012
i have tried several PH85img.zip files but the phone just scans them and goes back to the menu.
Some help will be appreciated extremely.
---------- Post added at 03:40 PM ---------- Previous post was at 03:33 PM ----------
I forgot to mention it connects to the pc but when i run command adb devices this is what i get
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\rquinlan.GOSL_DOM>adb devices
List of devices attached
C:\Documents and Settings\rquinlan.GOSL_DOM>

The latest ruu would be your best option, do not put the .zip part of the name since its already there, also a ruu may be an exe or zip file, since it is a complete stock file to restore the device, what would your carrier be to be exact? Just not up to reading through everything in this thread to see if you mentioned that piece of info, if its tmobile then the very first file in the stock ruu/ota thread would be the file you need.
Sent from my iPad using Tapatalk HD

thanks for your advice i managed to reboot the phone into recovery but heres whats strange to me the phone is in recovery with HTC on the screen thats it, the pc has recognized it as "MY HTC" in the device manager however, when i run the command adb devices this is what i get "SH218vp00163 offline". i ran the RUU file but i get error 170 usb connection.
so i am a bit lost as device manager can see the phone but the RUU file cannot and i am plugging the phone into the rear of the pc.
any ideas

Linkzz said:
thanks for your advice i managed to reboot the phone into recovery but heres whats strange to me the phone is in recovery with HTC on the screen thats it, the pc has recognized it as "MY HTC" in the device manager however, when i run the command adb devices this is what i get "SH218vp00163 offline". i ran the RUU file but i get error 170 usb connection.
so i am a bit lost as device manager can see the phone but the RUU file cannot and i am plugging the phone into the rear of the pc.
any ideas
Click to expand...
Click to collapse
Why are you using recovery exactly?
RUU's are to be flash via hboot, which is the very first screen you see when you go into the device's bootloader, in the case of exe files, you'll need to flash it via fastboot mode, which happens to be, correct me if I'm wrong, the very first or second option on the hboot menu.

yes you are correct cause i just tried it with an RUU from another carrier. i found out that the phone had 2.14.531 software installed. but the RUU i was using was 1.46 and so i got a signature error 132. now i need to find a way to remove the 2.14.531 software and replace it with a lower version. can you help me here

Linkzz said:
yes you are correct cause i just tried it with an RUU from another carrier. i found out that the phone had 2.14.531 software installed. but the RUU i was using was 1.46 and so i got a signature error 132. now i need to find a way to remove the 2.14.531 software and replace it with a lower version. can you help me here
Click to expand...
Click to collapse
What carrier are you on?

t-mobile
this is the RUU i tried and made a connection but the PH85img.zip are not working no matter how i try
RUU_Ruby_Videotron_CA_1.46.1530.1_R2_Radio_1.09.55 0L.17DC_30.68.550L.09_release_227343_signed.exe

need help for stock return

I am an unfortunate rookie, and have made mistakes, hence the name. I want to return my phone to stock from htcdev unlock, s-on, hboot 1.5. with a boot loop on meanom ICS for the evo 3d. I have tried to use older ruu shooters. Relock with fastbot oem lock, and then pg86img. However with the bootloop I can not access anything unless I unlock again, and then go into recovery. This is all that I can think of at the moment that might help.
Kill the rookie!!! PLEASE HELP!!

I had much the same problem with my cdma, hboot 1.5, S-On shooter. When I was S-On none of the ICS roms would work. The all bootlooped on me. If you follow the rooting method found here on xda, it will get you back to a stock Rooted GB Rom.
go into hboot -> fastboot USB-> run command dos -> fastboot cwm-4.0.1.4-shooter.IMG -> flash the 2.17 firmware-> enjoy.
I had to S-off with Juopunutbear, then re-run that root/flash to get past the bootloops.
Sent from my Shooter using xda app-developers app

Unfortunately I have tried that and it still is not working.

My only suggestion would be to try it a few times, other then that, its above my head.
Sent from my shooter using xda app-developers app

rookiemistake said:
I am an unfortunate rookie, and have made mistakes, hence the name. I want to return my phone to stock from htcdev unlock, s-on, hboot 1.5. with a boot loop on meanom ICS for the evo 3d. I have tried to use older ruu shooters. Relock with fastbot oem lock, and then pg86img. However with the bootloop I can not access anything unless I unlock again, and then go into recovery. This is all that I can think of at the moment that might help.
Kill the rookie!!! PLEASE HELP!!
Click to expand...
Click to collapse
Have you tried one of the ruu exe files that you run from your computer? If you are trying to go stock, you should be able to relock the bootloader and run the ruu and that's it.
Sent from my ICS 3VO with Tapatalk 2

First of all I want to thank everyone that has been attempting to assist me with my problem. I have tried to relock since I am on htcdev unlock and then run an ruu force via my computer. I get an installation aborted error when trying to flash pg86img via recovery. I don't know what else to say.

You can't flash a bootloader zip from recovery. You have to flash it from hboot. Also make sure the zip is named correctly "PG86IMG.zip" without the quotes. Also make sure the zip is on the root of your sd as in not in any folders. Once you've named the zip correctly and placed it correctly then power off the phone. Hold down the volume down button and tap the power button. You should boot into the bootloader wait until the phone recognizes the zip and follow the on screen instructions. Hopefully this helps.
#Root-Hack_Mod*Always\=LTE

Thank you again. I tried your directions, it did recognize the pg86img. However it did not give me any instructions to follow. It did however allow me to be able to a partial stock state. My software version is still on the teamgenesis sense v2.9 cdma. Although I do like some of the features on this rom, I would still like to be able to get the OTA of ICS when it is released. Any suggestions?

rookiemistake said:
Thank you again. I tried your directions, it did recognize the pg86img. However it did not give me any instructions to follow. It did however allow me to be able to a partial stock state. My software version is still on the teamgenesis sense v2.9 cdma. Although I do like some of the features on this rom, I would still like to be able to get the OTA of ICS when it is released. Any suggestions?
Click to expand...
Click to collapse
To get the ota release (if it ever comes ) I do believe you will need to be locked and running the existing gingerbread rom. While I am not positive, I think the system uses the props file to determine if an update is applicable, and it will likely not recognize the teamgenesis rom version as being upgradeable.
Now I will likely get flames for saying this, but if you want to put the meanrom v2.4 of ICS on the phone, it can be done with s-on, you just need to follow the correct process. I ran that rom for a while, and it is very stock like, stable, and has a few enhancements that you will not find on a non-rooted stock rom. I never found anything wrong or not working with that rom.
To get it to load, first I downloaded flashimagegui from market, put the meanrom zip file on the sd card and made sure I had a recovery that I could get into. I am using TWRP v2.1.1, lots of folks talk about others like ext4, and I am only going to say use whichever you like, after all it is your phone.
Then with the phone unlocked via the htc method, I started the flashimage app, and browsed to the meanrom file. It extracted the kernel and flashed it. Once that was done, with clear cache buttons selected, rebooted to recovery, and used the install menu selection of TWRP to again flash the same rom file. Once it flashed the file, selected clear cache and dalvik just to be safe, selected reboot system, and it worked great.
Have a great weekend.

So, apparently I am still doing something wrong. I have put the pg86img on the root, relocked to the bootloader, and let it run it's course. However, it will get through with reading it and stops and does not finish anything with loading the system information. I have also tried to run the ruu via usb connection. I keep running into a c++ issue saying runtime error. I have wiped everything and thankfully I did make a backup of the rom and other information that I was runing so I can currently fall back on that.
I am on hboot 1.5, 2.17, and teamgenesis ICS rom for evo 3d.
Apparently there have been rumors that Sprint has finally released the ICS OTA, not that it really matters anymore, but I have run into a few interesting glitches, such as WIFI not staying connected while asleep or disconnecting.
If I have to I am willing to pay to do a netmeeing with someone in order to be able to fix this.
Sorry if it sounds like I am getting frustrated, but I have tried every walkthrough that I have found and have not had any luck with any of them.
Please help.

I forgot to say I am s-on

[Q] Successful JuopunutBear S-OFF...Now stuck at juopunutbear screen

After sucessfully getting S-OFF with juopunutBear's wire trick.. I cant get past the black juopunutBear screen
ive tried recovering twice using 4ext..as well as just doing a full wipe except sd and reintstalling the rom but at reboot im right back at the J" screen.
Admittedly I am very green at this process. I took the steps one at a time ( all to try in flash the faux kernel )
So if anyone can or has encounter this problem and knows of the proper steps to get back into the normal boot pls help
much thnx in advance

connect your phone to pc & run again juopunutbear.That will fix it.

nothing changes it just informs me that the device is already s-off'd and then prompts me to exit
rebooting the device brings me right back to the black screen with the juopunutbear img

Try using Hasoon's AIO tool. You can add the kernel there and flash using his tool. It's been a while since I got stuck at that screen but I do remember that his tool helped me get out of it. I'll try and see what I find and post.
http://forum.xda-developers.com/showthread.php?p=22459381
Live and Die on this day....

I flashed an RUU to get out of it. If nothing else works, this will.

Double0EK said:
I flashed an RUU to get out of it. If nothing else works, this will.
Click to expand...
Click to collapse
This seems to be the appropiate step at this time because trying to reinstall a rom from recovery or flashing a kernal does nothing still just keep booting to the black juopunutbear screen..
Newb Question INC!,
how do i flash the ruu

blindnero said:
This seems to be the appropiate step at this time because trying to reinstall a rom from recovery or flashing a kernal does nothing still just keep booting to the black juopunutbear screen..
Newb Question INC!,
how do i flash the ruu
Click to expand...
Click to collapse
You could flash a RUU, then flash a j-bear boot, then flash a recovery, and then either flash a ROM of your choice, or flash a superuser package to get a rooted stock ROM...
or you could use this tool. I made it a while back ago, and this should work in your situation. Be sure to follow directions.

Keylogger_0 said:
You could flash a RUU, then flash a j-bear boot, then flash a recovery, and then either flash a ROM of your choice, or flash a superuser package to get a rooted stock ROM...
or you could use this tool. I made it a while back ago, and this should work in your situation. Be sure to follow directions.
Click to expand...
Click to collapse
ill give this a shot now thanks

thanks so much man great tool...
be sure to develop for the galaxy note ii once its out

blindnero said:
After sucessfully getting S-OFF with juopunutBear's wire trick.. I cant get past the black juopunutBear screen
ive tried recovering twice using 4ext..as well as just doing a full wipe except sd and reintstalling the rom but at reboot im right back at the J" screen.
Admittedly I am very green at this process. I took the steps one at a time ( all to try in flash the faux kernel )
So if anyone can or has encounter this problem and knows of the proper steps to get back into the normal boot pls help
much thnx in advance
Click to expand...
Click to collapse
If youre still javing the problem this will fix it
if you can go to bootloader you need to connect the phone to pc, go to fastboot ( should say fastboot usb)*Go to controlbear folder (from where you ran controlbear to begin withon you pc then open command window in it (hold shift and right click, that willopen command window rigjt there and then*when you get into it you need to enter:
"ControlBear.exe -f" no quotes or "ControlBear f" notice the space after the exe !
Lots of peopke forget to put it in and say it didnt work.
I presume this will fix the problem

HTC EVO 3D - Long Story - Trying to get back to GB with issues (Details in thread)

Hey all,
I have this HTC EVO 3D that just, refuses to co-operate with me.
Story goes -
Got it on ICS and everything was working fine on it. I looked for updates available and it found a 28MB update that I installed and once the phone rebooted with the update, the camera fails to start and the touch screen just starts going crazy and opening everything, whereas before it fine.
So, I attempted to try and get it back to Gingerbread.
And googled and googled and googled.
Reason why I have opened a new thread is cause it's sort of everything going weird with it.
Of course, trying RUU files and trying to flash RUU in zip failed so on so forth.
I had unlocked the Bootloader and S-ON is on at this point. Also had CWM recovery installed and was able to boot into that.
With this in place, I read up on the wire trick and thought, yeah it seems a bit hard, I'll take it to a phone repair shop, where they had the phone for 2 weeks and told me that it was S-OFF and back to stock.
Since they had it and I got it back, it's now stuck in a boot loop and I can not get into any recovery etc (With the original SD Card in it). Can get to Bootloader and fastboot though.
Spent the last 3 hours with about 20 tabs in Chrome opened on how to exactly go from here and I am stuck.
Got a Linux Laptop here and tried to ControlBear and it comes up with ADB and Fastboot not found (Directory points to it being in tmp..no idea)
TL;DR
HTC Evo 3D (Australian Variant, was running ICS Telstra OEM)
Unlocked Bootloader
SHOOTER_U PVT SHIP S-ON RL
HBOOT-1.53.0007
eMMC-boot
Radio - 11.25.3504.16 M
Boot Loops, No Recovery, Fastboot commands work on windows.
So just wondering, where do I go from here. I don't know if the device is completely bricked now or if it can be saved.
(I tried a number of zip files on the SD Card (PG86IMG.zip) and nothing due to having S-ON.
Hoping someone can provide a procedure or point me in the right direction.
As reference, I used this thread mostly before it was taken to the Repair Shop and got stuffed.
Any help is appreciated.
Thanks so much.

skylirizm said:
Hey all,
I have this HTC EVO 3D that just, refuses to co-operate with me.
Story goes -
Got it on ICS and everything was working fine on it. I looked for updates available and it found a 28MB update that I installed and once the phone rebooted with the update, the camera fails to start and the touch screen just starts going crazy and opening everything, whereas before it fine.
So, I attempted to try and get it back to Gingerbread.
And googled and googled and googled.
Reason why I have opened a new thread is cause it's sort of everything going weird with it.
Of course, trying RUU files and trying to flash RUU in zip failed so on so forth.
I had unlocked the Bootloader and S-ON is on at this point. Also had CWM recovery installed and was able to boot into that.
With this in place, I read up on the wire trick and thought, yeah it seems a bit hard, I'll take it to a phone repair shop, where they had the phone for 2 weeks and told me that it was S-OFF and back to stock.
Since they had it and I got it back, it's now stuck in a boot loop and I can not get into any recovery etc (With the original SD Card in it). Can get to Bootloader and fastboot though.
Spent the last 3 hours with about 20 tabs in Chrome opened on how to exactly go from here and I am stuck.
Got a Linux Laptop here and tried to ControlBear and it comes up with ADB and Fastboot not found (Directory points to it being in tmp..no idea)
TL;DR
HTC Evo 3D (Australian Variant, was running ICS Telstra OEM)
Unlocked Bootloader
SHOOTER_U PVT SHIP S-ON RL
HBOOT-1.53.0007
eMMC-boot
Radio - 11.25.3504.16 M
Boot Loops, No Recovery, Fastboot commands work on windows.
So just wondering, where do I go from here. I don't know if the device is completely bricked now or if it can be saved.
(I tried a number of zip files on the SD Card (PG86IMG.zip) and nothing due to having S-ON.
Hoping someone can provide a procedure or point me in the right direction.
As reference, I used this thread mostly before it was taken to the Repair Shop and got stuffed.
Any help is appreciated.
Thanks so much.
Click to expand...
Click to collapse
Hello my friend, the reason you can't load the pg86img is because you have unlocked bootloader. The fastboot commands could help us a lot, did you follow the controlbear instructions in the correct order? I think there is a way through windows with exe files I don't remember well because I did S-OFF 3years+ before. If you want we can try together some time. If you want for start we can flash 4ext recovery and a custom rom so your phone can boot.

mhnx said:
Hello my friend, the reason you can't load the pg86img is because you have unlocked bootloader. The fastboot commands could help us a lot, did you follow the controlbear instructions in the correct order? I think there is a way through windows with exe files I don't remember well because I did S-OFF 3years+ before. If you want we can try together some time. If you want for start we can flash 4ext recovery and a custom rom so your phone can boot.
Click to expand...
Click to collapse
Hi there, I didn't know with having the bootloader unlocked that it would cause any issues, but there you go!
Yeah, if there's a guide to flashing the 4EXT Recovery and a custom rom that would be great!
I have a fair idea of how to do it, but don't want to try anything without having someone of greater knowledge point me in the right direction
Thanks!

Just an update, I did come across a thread to flash 4EXT Recovery onto my Evo 3D.
Put Recovery.img into my platform-tools folder, used the fastboot command, it said sending and OK.
Selected recovery and still boot loops. No idea where to go from here now

skylirizm said:
Just an update, I did come across a thread to flash 4EXT Recovery onto my Evo 3D.
Put Recovery.img into my platform-tools folder, used the fastboot command, it said sending and OK.
Selected recovery and still boot loops. No idea where to go from here now
Click to expand...
Click to collapse
Sorry for being late, I had some problems with my internet connection. Can you boot into recovery? Power button + Vol- and choose recovery, if you can boot tell me first which version you have and second what type of rom you want to have.

mhnx said:
Sorry for being late, I had some problems with my internet connection. Can you boot into recovery? Power button + Vol- and choose recovery, if you can boot tell me first which version you have and second what type of rom you want to have.
Click to expand...
Click to collapse
Hey there,
That's OK, I don't mind the wait, it's all good!
I can boot into Fastboot, but when I choose recovery/factory reset etc, it shows the HTC Logo and then goes into a bootloop.
As for the ROM, I want to get the original GB ROM for it because when I updated it to the latest ICS that's when the camera and touch started to get weird, whereas beforehand it was fine.
So thinking, if I go back down to GB Stock, that it should be all fine again, but I am not too sure on that one.
Thanks!

skylirizm said:
Hey there,
That's OK, I don't mind the wait, it's all good!
I can boot into Fastboot, but when I choose recovery/factory reset etc, it shows the HTC Logo and then goes into a bootloop.
As for the ROM, I want to get the original GB ROM for it because when I updated it to the latest ICS that's when the camera and touch started to get weird, whereas beforehand it was fine.
So thinking, if I go back down to GB Stock, that it should be all fine again, but I am not too sure on that one.
Thanks!
Click to expand...
Click to collapse
Well, we have to downgrade the hboot version first. Did you do the wire trick procedure right? You can download a pg86img and flash it first to fix the bootloops. First lock the bootloader. When you finish this report here. I have to sleep it's late here and I work early. I'll send you tomorrow. See you.

mhnx said:
Well, we have to downgrade the hboot version first. Did you do the wire trick procedure right? You can download a pg86img and flash it first to fix the bootloops. First lock the bootloader. When you finish this report here. I have to sleep it's late here and I work early. I'll send you tomorrow. See you.
Click to expand...
Click to collapse
Ok, the technician I took the phone to supposedly did the wire trick for S-OFF, but, it's still S-ON.
I have downloaded a lot of stock PG86IMG files before posting on here and none work, they scan when in bootloader and then nothing after that.
But that would be because I haven't locked the bootloader. So in saying this, I lock the bootloader following steps on many forum posts on here, then flash a .zip file that's correct and then it should all work?
I'll wait for your response, thanks!

skylirizm said:
Ok, the technician I took the phone to supposedly did the wire trick for S-OFF, but, it's still S-ON.
I have downloaded a lot of stock PG86IMG files before posting on here and none work, they scan when in bootloader and then nothing after that.
But that would be because I haven't locked the bootloader. So in saying this, I lock the bootloader following steps on many forum posts on here, then flash a .zip file that's correct and then it should all work?
I'll wait for your response, thanks!
Click to expand...
Click to collapse
I do not think that the wire trick procedure was correct because you are still s on. Lock the bootloader and try to load the zip.

mhnx said:
I do not think that the wire trick procedure was correct because you are still s on. Lock the bootloader and try to load the zip.
Click to expand...
Click to collapse
Hey, so I tried a P86IMG.zip from this thread here - http://forum.xda-developers.com/showthread.php?t=2274635
I couldn't find another one and with that I get an error "Main Version Fail" or "Main Version Check Fail".
I then tried RUU and RUU in zip format.
RUU comes back with wrong bootloader error. (I couldn't find an RUU that matched my radio version so I went with the nearest one)
RUU Zip comes back through fastboot with "remote 43 main version check fail"
Also I tried to do the Wire Trick and got stuck at the "ADB and Fastboot not found" even though the files are there and the phone is connected.
So still a little bit...stuck :\
Also relocked bootloader it just says relocked now.
If you need any other additional info I can send screenshots of what it's at.
Thanks!

skylirizm said:
Hey, so I tried a P86IMG.zip from this thread here - http://forum.xda-developers.com/showthread.php?t=2274635
I couldn't find another one and with that I get an error "Main Version Fail" or "Main Version Check Fail".
I then tried RUU and RUU in zip format.
RUU comes back with wrong bootloader error. (I couldn't find an RUU that matched my radio version so I went with the nearest one)
RUU Zip comes back through fastboot with "remote 43 main version check fail"
Also I tried to do the Wire Trick and got stuck at the "ADB and Fastboot not found" even though the files are there and the phone is connected.
So still a little bit...stuck :\
Also relocked bootloader it just says relocked now.
If you need any other additional info I can send screenshots of what it's at.
Thanks!
Click to expand...
Click to collapse
Did you try flashing the zip after the locking? You are doing the wire trick procedure on live linux cd?

mhnx said:
Did you try flashing the zip after the locking? You are doing the wire trick procedure on live linux cd?
Click to expand...
Click to collapse
Yes, tried flashing the zip after locking. Live CD is being used also. I will try again later. Thanks!

skylirizm said:
Yes, tried flashing the zip after locking. Live CD is being used also. I will try again later. Thanks!
Click to expand...
Click to collapse
If you want we can do the procedure together some time. Keep in mind that you have to unlock again. We can search for the windows version too.

mhnx said:
If you want we can do the procedure together some time. Keep in mind that you have to unlock again. We can search for the windows version too.
Click to expand...
Click to collapse
I have windows version of wire trick procedure. If you need it, I'll gladly share it via PM

donkeykong1 said:
I have windows version of wire trick procedure. If you need it, I'll gladly share it via PM
Click to expand...
Click to collapse
Oh that would be extremely helpful, I can use Linux, but prefer my Windows PC as it has all the files and it's just easier.
Thanks so much!

mhnx said:
If you want we can do the procedure together some time. Keep in mind that you have to unlock again. We can search for the windows version too.
Click to expand...
Click to collapse
donkeykong1 said:
I have windows version of wire trick procedure. If you need it, I'll gladly share it via PM
Click to expand...
Click to collapse
So update -
DK sent me the windows version of ControlBear via PM - thank you.
Have an unlocked bootloader.
I tried ControlBear, and because I can not boot into the OS, I start it at Fastboot USB, it reboots, then says "Connecting to Device", then "Testing ADB connection" then "Press Enter To Exit" and that's it, can't do anything else from there, and it gets stuck in the boot loop that it still has.
Tried again to google for methods for HBOOT 1.53, and am trying some of those methods, but it's not looking good at all.
I haven't even got to the stage where it asks me to do any sort of wire trick.
Also my battery in the EVO 3D has died so am using a battery out of a HTC MyTouch 4G with help from electrical tape :\
So now, any suggestions? I am trying to flash another RUU that's stock for my Radio (Well, it's close enough - RUUs are both 11.25.3504.06, mine is 11.25.3504.16)
EDIT: Tried all RUUs with relocked bootloader and comes back with bootloader error (ERROR 140). So, no idea.
Also it's scanning for PG86DIAG.img files on the SD Card - that's not normal is it.
Do you think we should give up on it, it's probably hard bricked and dead now
I think it's literally hard bricked and no way to bring it back from the dead.
As per my original post, all the details for the phone are there. And it sucks that I can't find a correct RUU for my phone (As it was Telstra AU - latest update of ICS)
AHH I don't know.

skylirizm said:
So update -
DK sent me the windows version of ControlBear via PM - thank you.
Have an unlocked bootloader.
I tried ControlBear, and because I can not boot into the OS, I start it at Fastboot USB, it reboots, then says "Connecting to Device", then "Testing ADB connection" then "Press Enter To Exit" and that's it, can't do anything else from there, and it gets stuck in the boot loop that it still has.
Tried again to google for methods for HBOOT 1.53, and am trying some of those methods, but it's not looking good at all.
I haven't even got to the stage where it asks me to do any sort of wire trick.
Also my battery in the EVO 3D has died so am using a battery out of a HTC MyTouch 4G with help from electrical tape :\
So now, any suggestions? I am trying to flash another RUU that's stock for my Radio (Well, it's close enough - RUUs are both 11.25.3504.06, mine is 11.25.3504.16)
EDIT: Tried all RUUs with relocked bootloader and comes back with bootloader error (ERROR 140). So, no idea.
Also it's scanning for PG86DIAG.img files on the SD Card - that's not normal is it.
Do you think we should give up on it, it's probably hard bricked and dead now
I think it's literally hard bricked and no way to bring it back from the dead.
As per my original post, all the details for the phone are there. And it sucks that I can't find a correct RUU for my phone (As it was Telstra AU - latest update of ICS)
AHH I don't know.
Click to expand...
Click to collapse
First of all you should be unlocked now with 1.53 hboot. Download from here the latest 4ext recovery (4EXT_Recovery_Touch_v1.0.0.6_RC3)
It's in my mega account don't worry about malicious software I downloaded it 5 minutes before doing this post. If you don't have unlocked your bootloader do it with the tokens HTC sent you in your email. Flash this recovery from fastboot (fastboot flash recovery "recoveryname".img). After that remove the battery and re-enter fastboot mode (Vol down+power button) and choose recovery. If you manage to boot into recovery from there tell me to send you a link for a rom to flash. I don't believe its a hard brick.

mhnx said:
First of all you should be unlocked now with 1.53 hboot. Download from here the latest 4ext recovery (4EXT_Recovery_Touch_v1.0.0.6_RC3)
It's in my mega account don't worry about malicious software I downloaded it 5 minutes before doing this post. If you don't have unlocked your bootloader do it with the tokens HTC sent you in your email. Flash this recovery from fastboot (fastboot flash recovery "recoveryname".img). After that remove the battery and re-enter fastboot mode (Vol down+power button) and choose recovery. If you manage to boot into recovery from there tell me to send you a link for a rom to flash. I don't believe its a hard brick.
Click to expand...
Click to collapse
Hey there, thanks for the help again, unfortunately, still didn't work.
I unlocked the bootloader again. Then tried to flash what you said, it said "writing" then "successful". I pulled the battery and tried to boot into recovery and just loops

skylirizm said:
Hey there, thanks for the help again, unfortunately, still didn't work.
I unlocked the bootloader again. Then tried to flash what you said, it said "writing" then "successful". I pulled the battery and tried to boot into recovery and just loops
Click to expand...
Click to collapse
Try doing:
fastboot erase recovery
fastboot flash recovery "recovery".img
fastboot format system
fastboot format boot
And if it still doesn't let me send you a boot.img in some minutes to try flashing it.
EDIT: And something last, you can still do the controlbear trick while not in OS, its easy if you wanna try let me know.

skylirizm said:
Hey all,
I have this HTC EVO 3D that just, refuses to co-operate with me.
Story goes -
Got it on ICS and everything was working fine on it. I looked for updates available and it found a 28MB update that I installed and once the phone rebooted with the update, the camera fails to start and the touch screen just starts going crazy and opening everything, whereas before it fine.
So, I attempted to try and get it back to Gingerbread.
And googled and googled and googled.
Reason why I have opened a new thread is cause it's sort of everything going weird with it.
Of course, trying RUU files and trying to flash RUU in zip failed so on so forth.
I had unlocked the Bootloader and S-ON is on at this point. Also had CWM recovery installed and was able to boot into that.
With this in place, I read up on the wire trick and thought, yeah it seems a bit hard, I'll take it to a phone repair shop, where they had the phone for 2 weeks and told me that it was S-OFF and back to stock.
Since they had it and I got it back, it's now stuck in a boot loop and I can not get into any recovery etc (With the original SD Card in it). Can get to Bootloader and fastboot though.
Spent the last 3 hours with about 20 tabs in Chrome opened on how to exactly go from here and I am stuck.
Got a Linux Laptop here and tried to ControlBear and it comes up with ADB and Fastboot not found (Directory points to it being in tmp..no idea)
TL;DR
HTC Evo 3D (Australian Variant, was running ICS Telstra OEM)
Unlocked Bootloader
SHOOTER_U PVT SHIP S-ON RL
HBOOT-1.53.0007
eMMC-boot
Radio - 11.25.3504.16 M
Boot Loops, No Recovery, Fastboot commands work on windows.
So just wondering, where do I go from here. I don't know if the device is completely bricked now or if it can be saved.
(I tried a number of zip files on the SD Card (PG86IMG.zip) and nothing due to having S-ON.
Hoping someone can provide a procedure or point me in the right direction.
As reference, I used this thread mostly before it was taken to the Repair Shop and got stuffed.
Any help is appreciated.
Thanks so much.
Click to expand...
Click to collapse
i have same problem plz give me GB rom link and flash method
---------- Post added at 07:56 AM ---------- Previous post was at 07:42 AM ----------
mhnx said:
First of all you should be unlocked now with 1.53 hboot. Download from here the latest 4ext recovery (4EXT_Recovery_Touch_v1.0.0.6_RC3)
It's in my mega account don't worry about malicious software I downloaded it 5 minutes before doing this post. If you don't have unlocked your bootloader do it with the tokens HTC sent you in your email. Flash this recovery from fastboot (fastboot flash recovery "recoveryname".img). After that remove the battery and re-enter fastboot mode (Vol down+power button) and choose recovery. If you manage to boot into recovery from there tell me to send you a link for a rom to flash. I don't believe its a hard brick.
Click to expand...
Click to collapse
plz help my htc evo 3d is bootloop no go to any recovery mode i flash all recovery
BOOTLOADER-UNLOCK
HBOOT-1.53.0007
RADIO-11.25.3504.06.M
i flash many ruu.exe but this
RUU_SHOOTER_U_ICS_35_S_hTC_Asia_WWE_3.28.707.1_Radio_11.77.3504.00U_11.25.3
flash seccussfully without any error but no booting only htc logo plz help

Better Mobile App

welcome