I am not able to connect my Transformer Prime with my new Asus N66U router. I tried all channels and security settings and it only connected when to the router with open system setting. I am able to connect it to my old Netgear WDR3700 in good speed without any problems. Does anyone run into similar situation?
I have the rt-n66u router as well and never had a problem. Are you sure you are using the right encryption settings, Do other devices connect, have you updated the router's firmware? There was a new update just today.
http://support.asus.com/download.as...T-N66U (VER.B1)&os=&hashedid=PZkFHlMrGWzVROxT
have you ensured your router has the latest firmware?
I have the N56u model and no issues.
Yes, I have the latest firmware. My Galaxy Nexus connects just fine. The Transformers Prime actually see the router with strong signal. It just refuses to connect to it. BTW I set the router using WPA-PSK.
Is your prime running the latest update? Or, have you tried DD-WRT?
I have the latest firmware in both devices. However, my Prime is the first batch and may suffers from wifi issues. I may have to try Tomato or Dd-wrt firmware.
Sent from my Galaxy Nexus using Tapatalk 2
Some routers let you disable the broadcasting of the network name (SSID). Computers/network cards that conform correctly with the 802.11 specification will refuse to connect. Have you checked the settings for both 2.4 and 5GHz? - of course the router should not allow disabling of the SSID!
odd. Try wiping the data. Small pin hole in back of router. Reset it. Then 192.168.1.1. go in there and reenter your SSID etc on wireless.
For ****s and giggles. Pump up your 80mw Tx power of wireless to around 160mw. I been running 160mw tx power for awhile and have not and any problems. This baby can go all the way up to 500mw. Of course that is U.S. FCC range limit. With 500mw you can see your wireless from few blocks away.
If your prime is connecting to your other wireless router. Then has to do with some setting in on the RTN66U. Hopefully the wipe will clear any setting in the firmware.
Forgot to mention. Your prime will only connect to the 2.4ghz. It won't connect to the 5ghz wireless.
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
ariesting said:
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
Click to expand...
Click to collapse
What are the WiFi standards on the Router set to?
Sometimes when a router is set to b/g/n (all combined) it can lead to issues.
I generally keep mine at b/g (no n) on the 2.4 Mhz band, since my n devices run on my router's 5 Ghz band anyway. Try that out.
I tried "auto", "legacy" and "n only" with or without "b and g protection" but still could not connect to the router in any combinations. Will like to know the feedback from anyone who put Tomato on N66U.
If you have kept the same SSID as your old router did you delete the old network settings for that SSID in your TP? Also try a new SSID on the router.
If the router supports WiFi Multimedia (WMM) try disabling it and re-enable it after a connection has been made.
I presume you would know if you had enabled an allowed devices table -MAC addresses. The only other thing I can think of is the size of the "hello I'm here" beacon that the router transmits is too long for the TP and I think that would only be an issue with a very long SSID
Yes, I do keep the old SSID. However, I did forget the network and reconnect to it again in Transformer. My SSID is less than 10 characters. It seems to me that the Transformer is not able to get an IP nor pass the authentication stage.
ariesting said:
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
Click to expand...
Click to collapse
Well. Go under advanced settings and then Wireless.
Wireless -General tab.
Frequency click (2.4ghz).
Your SSID (name).
Hide SSID = (No)
Wireless Mode put in (N Only).
Control Channel (1).
Channel Bandwidth (20mhz).
Authentication Method (WPA2-Personal).
WPA Encryption (AES).
Enter your WPA Pre-Shared Key (password for SSID).
Network Key Rotation Interval to (0).
Wireless -Professional Tab
Frequency (2.4ghz)
Enable Radio (yes)
Date to Enable Radio (Check all days)
Set AP Isolatd (No)
Multicast Rate (Disable)
RTS (2347)
DTIM (3)
Beacon (100)
Enable TX burst (Enable)
Enable Wireless Multi (Disable)
Enable WMM (Enable)
Tx Power adjustment (80)
Try those settings. See what happens.
Will try it as soon as I get back home. Thanks.
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
ariesting said:
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
Click to expand...
Click to collapse
Good to hear!
I've had the occasional connectivity problem with mine, on certain routers I can get connection but no online connectivity.
some routers use a nonstandard DHCP range (i think it may the ones that utilise 192.168.1.x) anyway, if you encounter this it's simple to correct once you know you simply define a manual ip on the prime for that connection and voila! :>
ariesting said:
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
Click to expand...
Click to collapse
Cool. Glad you got it working.
Well you can always try and pump your TX power adjustment from the default 80 to 160 or more. I was able to increase my range. I think the max is like 500mw the chip is rated at. However, I havent tried that high. I don't want to burn out my chip. Plus heat increases dramatically at those higher mw's. You would have to toss a little laptop cooler underneath it. (run via the routers usb port there).
My connection problem happens again. Just in case someone has similar issue, I solve the problem by exchanging a new one from store.
ariesting said:
I am not able to connect my Transformer Prime with my new Asus N66U router. I tried all channels and security settings and it only connected when to the router with open system setting. I am able to connect it to my old Netgear WDR3700 in good speed without any problems. Does anyone run into similar situation?
Click to expand...
Click to collapse
I have the n66u too and have no issues.
Related
Hi,
so kernel sources are released. Is there any fix for hero's wifi problems? I mean dropping connection to AP. It is so annoying, I tried to do everything: change channel, mode, encryption... Nothing helped. It is Linksys wrt160nl. The same applies to other networks (some public hot spots).
I never had this problem with my Linksys WRT54GL...
mopodo said:
I never had this problem with my Linksys WRT54GL...
Click to expand...
Click to collapse
Could you paste your wifi settings? (mode, encryption mode, channel)
Using the Modaco custom ROM 2.8 (never had problems with modaco ROM and generic)
Router: Linksys WRT54GL running Tomato 1.25 firmware
Wireless Mode: Access Point
B/G Mode: Mixed
Channel: 1 - 2.412 Ghz (try a free one)
Security: WPA / WPA2 Personal
Encryption: AES
Group Key Renewal: 3600 seconds
No Mac Filter
Under Advanced Settings I changed "Transmit Power" to 251mW for a better signal, the rest are default values.
Try to update your router firmware
Are you alone with this problem?
greetz
In case you haven't done so yet. Check out the Wifi Sleep Policy (access by pressing menu when you are in wifi menu). Normally the Wifi is turned off then the screen is turned off which can cause problem.
Similar problem with netgear wnr2000
mopodo said:
Using the Modaco custom ROM 2.8 (never had problems with modaco ROM and generic)
Router: Linksys WRT54GL running Tomato 1.25 firmware
Wireless Mode: Access Point
B/G Mode: Mixed
Channel: 1 - 2.412 Ghz (try a free one)
Security: WPA / WPA2 Personal
Encryption: AES
Group Key Renewal: 3600 seconds
No Mac Filter
Under Advanced Settings I changed "Transmit Power" to 251mW for a better signal, the rest are default values.
Try to update your router firmware
Are you alone with this problem?
greetz
Click to expand...
Click to collapse
Hi got similar problem with my router netgear wnr2000.what i found funny is that when i reset the router, the phone connects perfectly to the router, but after abt 24hrs or so, it fails to connect.even if i reboot my phone, or reset the connection on phone.fails to connect.it will only connect when i reboot the router. i will try the 'aes' encryption n see if that helps.will update if it works
Thanks for your replies. Please could other members share their experiences, used options and solutions. This issue is too common to simply forget it. I am trying to find some kind of pattern or special options, it requires.
i dont have a problem with wifi apart from the wont find or connect to n-range device other wise i use wifi all the time it never drops, on stock orange uk firmware
I have a Sitecom WL-173 router.
I cannot connect at all. I can, but only with no or WEP security. That is no option for me.
When I use WPA or WPA2 my Hero does view my network, but does not connect.
I called HTC about this problem. He told me that they do not support all routers. He could not tell me which they support and which not.
mopodo said:
B/G Mode: Mixed
Click to expand...
Click to collapse
I also have the same problem. The way to solve it is to change the above setting to 'G' only. Not mixed/Hybrid.
Cheers!
I have not had any problems trying to connect to WiFi networks, until i went over to my mates place where he has the Virgin 50MB B-Band and also a D-Link wifi-N router, and my Hero could no see the network at all, even though his iPhone connected straight away.
markoc84 said:
..., even though his iPhone connected straight away.
Click to expand...
Click to collapse
Augghhhhh... that hurts. Please, do not curse in this forum
tembares said:
Augghhhhh... that hurts. Please, do not curse in this forum
Click to expand...
Click to collapse
I'm sorry, it hurt even more when i was sitting there pissed off that my Hero wouldnt connect to the Wifi!!!
I have Virgin 50meg at home no problem at all, went to my GF's who has basic Virgin cable 10meg on netgear G and would not connect at all.
No idea why, as it should be all fine!
I have the same problem. It is so ****in annoying. My router is a Linksys WRT54G with Tomato firmware v1.25. Router is in "G only mode", WPA-2 PSK-AES security, I've set a static local IP for the phone, the phone's wireless is set to always ON... I basically tried everything I could think of. Ended up rooting the phone and installing Modaco 2.9... but didn't change anything. The only way I can get it work again when it drops is shut the Wi-Fi off then on...
Worst of all this is the problem seems widespread (but not universal)... What the **** does HTC think putting a ****in smartphone on the market with defective Wi-Fi... This is non-sense.
I really hope someone comes up with a fix or HTC updates this... otherwise we might want to start thinkin bout class action.
[email protected] said:
I also have the same problem. The way to solve it is to change the above setting to 'G' only. Not mixed/Hybrid.
Cheers!
Click to expand...
Click to collapse
Is it a router setup or a Hero setting?
Pleaes explain if it's one of the options
probs here too ...
Linksys WAP54G v3.1
vs
HTC Hero
was working perfectly for first month or so, but has been getting worse and worse. ie, for a few weeks it would see the wifi but would usually fail to connect. now I'm lucky if it can see it at all!
have reflashed the wap with dd-wrt and experimented with a lot of settings. no diff.
have reflashed the hero with hero21 comunitry v1.6. no diff. (and also latest radio)
it just starts and stops when it feels like it.
oh, and my eeepc works fine on the same wifi, so I know it's not some wap screw up.
tried every tip I can find like 'use mixed mode' or 'g only', etc etc.
I am starting to think it's a hardware fault?
Same problem
Siemens Gigaset Tiscali modem with wpa psk2 tkip and T-mobile hero rom.
Sees the modem and connects with security first time but then says 'remembered out of range' on wifi settings but interestingly in wifi buddy it constantly has the syncing symbol next to the network.
Really annoying.
I've tried WEP and security off, wireless g only etc etc.
I have problems too but seems different to yours... but who knows : in fact i can't connect to wifi when the SSID is masked. Even if - or course - i put manuualy the ssid before with the good wep key. It happens on a livebox ( orange box )... but if i press the button to show the wifi network - it has to be made when you connect a device for the first time on this box - then it connects to the network... else it tells me that the network is out of range...
So does the wifi on hero has problem with masked SSID ? To compare i never had this problem - on the same box - with the touch diamond and the touch hd... and at home, not masking the ssid, the connection is ok without doing anything.
Ciao
Fred
I had the same problem with a Zyxel 660 router. I was able to connect to the wifi (WPA/PSK enable) but there was no data transfer possible.
So I updated the Radio ROM to the 63.18.55.06JU_6.35.08.29 version and it solved the problem.
Hi just received my GTablet and have installed ClockworkMod v08. Next, I am attempting to install the TNT Lite Rom but I am having trouble connecting to my home router.
The response I keep getting when trying to connect is to the point of "Obtaining IP address.." then it disconnects. I am sure it's not the wireless router but just to be eliminate possibilities, I've even switched off all the security with connect to the router, but the sames results. It keeps trying to re-connect. I can easily connect with my other PCs and printers.
Any ideas? Thanks in advance.
Hello there,
did you ever solve your wifi problem, I am currently running the latest TnTlite, and this just started happening to me as well. It just hangs in Obtaining Ip then it disconnects.... I have never had this problem before in fact was online on the tab last night, now it seems i cannot connect... I will see if I can connect in another location hope nothing happened to the Tab..... BTW I tried restarting as what was suggested but that did nothing for me also....
Are you broadcasting your SSID?
Can you take the tablet somewhere else and try connecting at a Star Bucks, or a library, or something. See if it connects ok there?
Also, if it doesn't connect anywhere. Try flashing a different ROM to see if it is just that one.
I've had the same problem. I do not seem to be able to connect to any wifi that is encrypted with WPA. At work, we are WPA and I cannot connect at all. At home, I have WEP and can connect. I thought it might be something with the wifi settings on the tab, and have searched and searched and cannot find anthing.
By the way, this is my third tab and none of them could connect to a WPA encrypted router. The first two I returned as defective. IF there is an answer, I would love to hear about it.
Also, this is my first android device. I have been messing with Windows phones for a long time...thanks to the great people on this site.
Sorry to hear about your wifi problems. Just to let you know my experiences, I've (in the week I've owned my tablet) run TnT, VegaN and cyanogen (latest of each) and have never had a problem connecting to my home wifi - I do not broadcast my SSID at all and use WPA2/PSK encryption. You both mention WPA - can either of you try WPA2/PSK?
But on saying all of that, if you can't even connect to your wifi point without any security involved, it sounds either:
1) Hardware - faulty tablet but you said you're on your third so that sounds unlikely. Remember, while the tablet supports wifi G/N it does so over 2.4Ghz so if you have a router that only does 5Ghz or is set to work exclusively over 5Ghz, your router will not see your tablet
2) Software related - Have you reflashed your kernel at all? Did you possibly install a kernel (not rom) that does not have wifi drivers installed or something similar?
I hope something above might help you....
I was never able to connect to the wireless router. I shut all the security off, reset the router, rebooted the tablet but still the same results, "obtaining IP address" then it fails and tries again. I could connect to my neighbors Linksys so I know the tablet wifi is ok. I also so know that the router was ok since it had been serving my other PCs & printers for a number of years. It just wouldn't connect to each other.
The problem still persists.
+++++++++++++++++
Running TNT Lite 4.2.1
bevbeng said:
I was never able to connect to the wireless router. I shut all the security off, reset the router, rebooted the tablet but still the same results, "obtaining IP address" then it fails and tries again. I could connect to my neighbors Linksys so I know the tablet wifi is ok. I also so know that the router was ok since it had been serving my other PCs & printers for a number of years. It just wouldn't connect to each other.
The problem still persists.
+++++++++++++++++
Running TNT Lite 4.2.1
Click to expand...
Click to collapse
You didn't answer in your response above, is your router a 5Ghz router or 2.4Ghz? Could the frequency of your router be causing your problem here? Remember the tab only supports 2.4Ghz frequencies
1. if your tablet can connect to your neighbor's router, then problem lies between your router and the tablet.
2. is your router a linksys? what wireless router are you trying to use?
3. are you using mac address filtering? is dchp enabled on the router or by some sort of home server?
4. your tablet can see your router, but for some reaon they cant agree on how to talk to each other. i'm on a linksys wrt54gsv4 and havent had a problem, not with default settings or wpa2 or mac filtering or the custom firmware i eventually installed on it (ddwrt), tomato)
Sent from my GTablet-TnT-Lite using Tapatalk
bevbeng said:
Hi just received my GTablet and have installed ClockworkMod v08. Next, I am attempting to install the TNT Lite Rom but I am having trouble connecting to my home router.
The response I keep getting when trying to connect is to the point of "Obtaining IP address.." then it disconnects. I am sure it's not the wireless router but just to be eliminate possibilities, I've even switched off all the security with connect to the router, but the sames results. It keeps trying to re-connect. I can easily connect with my other PCs and printers.
Any ideas? Thanks in advance.
Click to expand...
Click to collapse
You are ATTEMPTING to install TnT ROM? You dont need the Internet connection, just sideload it then install. Am i Right?
Then after you install the TnT rom, sideload also the Kernel TnT base with wifi fix.
http://forum.xda-developers.com/showthread.php?t=895825
Hope this will solve your problem.
Good luck
powercrazy said:
You didn't answer in your response above, is your router a 5Ghz router or 2.4Ghz? Could the frequency of your router be causing your problem here? Remember the tab only supports 2.4Ghz frequencies
Click to expand...
Click to collapse
I have an older Microsoft 2.4Ghz B/G wireless Router. I'll try to sideload the Kernel TNT base with the WiFi fix.
Thanks for the tips.
Since the original posting I have got TNT Lite installed (using my neighbors router)
bevbeng said:
I have an older Microsoft 2.4Ghz B/G wireless Router. I'll try to sideload the Kernel TNT base with the WiFi fix.
Thanks for the tips.
Let us know if it solve. If not, I think you have defective unit.
Goodluck!
Click to expand...
Click to collapse
Something else occurs to me out of pure ignorance. I'm not sure how Android stores profile information. But I know with both mac and windows I've had occasion where "forgetting" the network and letting the device rediscover it has solved problems.
It sounds like you've been down that road already. However, it does bear asking. It's the more obvious things we often forget to consider.
Well it looked like the tablet needed to be reset a couple of times as i was just online with it... now the tab just froze, shut off and now i cannot turn it on... off to another thread to see what to do now... god i hope this thing is not bricked....any suggestions on what is a good thread would be appreciated... off i go.......
edit: found a thread now to find the internal reset button. thanks to all at xda....
RyuFDAC01 said:
Well it looked like the tablet needed to be reset a couple of times as i was just online with it... now the tab just froze, shut off and now i cannot turn it on... off to another thread to see what to do now... god i hope this thing is not bricked....any suggestions on what is a good thread would be appreciated... off i go.......
edit: found a thread now to find the internal reset button. thanks to all at xda....
Click to expand...
Click to collapse
Try to hold the power button for a long time and maybe it may turn back on. Before doing your last resort (disecting the tablet).
I had a problem with my wifi going into loops when I first got the unit. It would show it connecting/disconnecting/connecting/etc as described in the first post.
I had another router (both the same makes - Linksys WRT54G but different model numbers) so I tested the other router and I connected fine. I haven't gone back to test the first router yet and I am using the 2nd one.
The router I couldn't connect to has DD-WRT micro on it, and I haven't had problems connecting other wireless devices to. The one that is working fine with the g-tablet now has Tomato on it (it is a lower version number which supported Tomato).
Too bizarre... I now have this problem.
I received my gtablet today and installed clockwork mod recovery and vegan-tab ginger RC 1. Or, essentially, I followed the instructions here and got everything working. http://forum.xda-developers.com/showthread.php?t=865245
Wifi worked fine until the evening. Wifi is on, and in the settings under the SSID of my wifi network, it says Obtaining IP address for a minute until it says Disabled, network in range. I've done some common trouble shooting, like restarting, turning wifi off and on, forgetting the network and reentering password. That didn't work. My cell phone has a mobile hotspot feature and the gtablet CAN join that. I wonder what gives... I hope someone can help.
(This could be just coincidence, but it's about when I powered up my desktop computer. The desktop connects to the internet through a DMZ router that has a wired connection to the wifi router in another room. The desktop is now off and the gtablet still has this problem.)
Ok. Resetting my router fixed it. I never thought that my router could just "dislike" one particular device. I thought for sure something had to be wrong with the device. Forgive my ignorance!
G Tablet Wifi
I do not transmit my SSID and this has never been a problem with any of our laptops or netbooks. When I first received my G Tab and tried to connect to my network, even though I had entered the SSID and Passphrase correctly, it still would not connect. As soon as I set my wireless router to transmit the SSID the G Tab connected without any problems.
This is the first time I've encountered a problem of this nature. Comments?
This is what worked for me. I posted this in a similar thread as well.
Hey, I had WiFi connection issues too. I just got a Viewsonic G-Tablet with the Android 3.0 OS and have a D-Link DI-524 wireless router. It could see router and would try to connect, but would cycle and never connect. I could try to connect to other available networks in the area. It connected fine to an unsecure network, and when I tired to connect to secure networks there was a place where I could enter a network key/password. However, I noticed this option was not available on my network when I tried to connect. I reset my router which did not help. I then chose the option to add a network on the tab. This worked!! I was able to enter the key from the add a network option. I then told the "bad" connection to be forgotten. Hope this helps someone else, as I had looked on the internet for awhile for an answer. I was about to buy a new wireless router too!! Oh, I am using WEP too.
edit: ok when I power my tablet back on the same issue was happening. This time I could enter a network and the cycling still contiuned. I even forgot and re-entered the network. The fix this time was to reboot the tab. However, my internet has been acting up lately so IDK.
So it seems that there is no way to connect to a non broadcasting wifi network in any of the current froyo roms. Anyone got any ideas on how to resolve this?
I have tried hidden wifi enabler and even added it separately, but it just says out of range when its sitting right next to the wireless router. With broadcasting on it connects with no problems.
tnerb123 said:
So it seems that there is no way to connect to a non broadcasting wifi network in any of the current froyo roms. Anyone got any ideas on how to resolve this?
I have tried hidden wifi enabler and even added it separately, but it just says out of range when its sitting right next to the wireless router. With broadcasting on it connects with no problems.
Click to expand...
Click to collapse
I've done it in Vegan... what encryption are you using? I know there are issues with WEP...
using wpa2 I heard rumors that tkip doesnt work with it. This correct?
I got mine to connect running stock and TNT 4.4 but it wasn't easy. I intially went into wifi setting and "add a network" typed in the SSID (not being broadcast) and password (WPA2/TKIP) and it would find the network but not connect. I did some searches and found various suggestion but none worked.
After a lot of failed attempts I got frustrated and turned off wifi on the tablet and then turned it back and suddenly it connected with no problems. It may have been a one off thing but couldn't hurt to try it.
nik
Ill give this a try and see what happens. But I am not getting my hopes up.
Just out of curiosity.....
What's the point of connecting to non-broadcasting router?
It's like turning on WiFi in the middle of desert?
JMO.....
turn on ssid bdcst. connect then turn bdcst off.
Tester30 said:
Just out of curiosity.....
What's the point of connecting to non-broadcasting router?
It's like turning on WiFi in the middle of desert?
JMO.....
Click to expand...
Click to collapse
If your wireless router doesn't broadcast it's SSID, others can not attempt to access it.
My Stock 3588 connects fine
I have a non broadcasting router in my home and stock 3588 on my gtab. Did the connection once when I bought the tab and it has been connecting just fine for couple months now!
LGCubana said:
If your wireless router doesn't broadcast it's SSID, others can not attempt to access it.
Click to expand...
Click to collapse
So not even close to true
Using a non-broadcast SSID as a security measure is probably the weakest (well...next to no encryption at all) method available.
LGCubana said:
If your wireless router doesn't broadcast it's SSID, others can not attempt to access it.
Click to expand...
Click to collapse
Using a Linux PC, I can see ALL available wireless APs with this command:
Code:
iwlist wlan0 scan
Hiding the SSID is not even considered to be a security option, it is that poor. Save yourself some trouble and let it broadcast the SSID.
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Is there any specific settings I need to configure on my router? I am using a Prolink H5004N adsl2+ modem with wireless N router. The modem is compliant to IEEE 802.11n standards, not draft-n and should work with the SGS2?
wind79 said:
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Is there any specific settings I need to configure on my router? I am using a Prolink H5004N adsl2+ modem with wireless N router. The modem is compliant to IEEE 802.11n standards, not draft-n and should work with the SGS2?
Click to expand...
Click to collapse
Not sure, but I think that it will connect if your N-network are in the 2.4 GHz frequency area, but not in the 5.0 GHz
mljjlm said:
Not sure, but I think that it will connect if your N-network are in the 2.4 GHz frequency area, but not in the 5.0 GHz
Click to expand...
Click to collapse
Yup, tried that too, but still connects to G only. I have also tried configuring router to accept only N networks instead of G/N, but then the SGS2 will not even see the SSID when its performing a wireless scan.
wind79 said:
connecting our SGS2 to Wireless N network?
Click to expand...
Click to collapse
Ive got the same issue. Router Asus RT-N16 (b/g/n, 2.4GHz). Playing with different router firmwares, settings and so on - no luck so far.
Check the "advanced" settings by pressing the menu button in the wireless and make sure nothing wierd is set in there.
Otherwise, as long as the router is set to N only on the 2.4ghz band, it should at _least_ see the SSID.
That modem supports WPS, try pressing the WPS button on the back of the modem and then use the "WPS button connection" option in the wi-fi settings menu on the SGS2.
Remember the single-channel 802.11n 2.4ghz such as the SGS2 supports will only max out at 72mbps anyway so there's not a huge improvement over the 54mbps that 11g will give you, although 11n is more efficient.
grey77 said:
Ive got the same issue. Router Asus RT-N16 (b/g/n, 2.4GHz). Playing with different router firmwares, settings and so on - no luck so far.
Click to expand...
Click to collapse
I've got the same unit and it works fine with it, that said I'm running a recent build of the Tomato firmware on mine. I don't think I even powered it up fully with the original firmware...
knightnz said:
Check the "advanced" settings by pressing the menu button in the wireless and make sure nothing wierd is set in there.
Otherwise, as long as the router is set to N only on the 2.4ghz band, it should at _least_ see the SSID.
Click to expand...
Click to collapse
thx for fast reply
SGS2 can see SSID, but fails to connect until I force RT-N16 (with custom firmware, RT-N16-1.9.2.7-rtn-r3121) down to "Use 802.11 G only".
Never had any problems with other 802.11 N powered devices.
only wpa2-aes or no encryption are N-standard
wind79 said:
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Click to expand...
Click to collapse
wireless N only officially supports either WPA2-AES encryption or no encryption. Devices with drivers that more closely comply to the spec will not connect to WEP or WPA.
I hope you fixed the issue. I stumbled across this thread while asking the same question; maybe someone else will benefit by having this thread wrapped-up also. No haters, egos, persons, etc please. It's been necessary already to block a few of you.
To help my WiFi Signal in other parts of my Home I added a Linksys Wireless G Access Point. My Prime sees this new AP and I can "manually" go to Settings and Disconnect from my Linksys 54g Router and Connect to the AP and it Works Great. My question is: Is there a way to set up the Prime to "auto" switch to the AP as my Strength weakens and then switch back to Wireless Router as needed?
Thanks
Check your Linksys manual, as there is probably a mode for this ... might be called "repeater" mode ... with that you'd be extending your current wi-fi SSID, rather than creating a new one. If you already knew all of this ... sorry.
tedr108 said:
Check your Linksys manual, as there is probably a mode for this ... might be called "repeater" mode ... with that you'd be extending your current wi-fi SSID, rather than creating a new one. If you already knew all of this ... sorry.
Click to expand...
Click to collapse
No I didn't know that.Thanks so much and I'll give it a try.
Found something for you:
http://www.labnol.org/internet/extend-wifi-wireless-network-range/13534/
Especially read Options 1 & 2 under extending your wireless range via hardware. If you want to use your current router to extend your wi-fi, you may have to buy an ethernet cable and connect it to your other router.