Related
My gtab is going in for warranty repair for a loose power connector pin. They said they'll swap out the circuit board because it's too hard to correct by soldering.
I have rooted it, and have many paid apps. Is there a way to save an image file like with a PC HD so I can restore it back to what I have now? If not, what's the best way to save/restore as much as possible?
Thanks
retiredrobb said:
My gtab is going in for warranty repair for a loose power connector pin. They said they'll swap out the circuit board because it's too hard to correct by soldering.
I have rooted it, and have many paid apps. Is there a way to save an image file like with a PC HD so I can restore it back to what I have now? If not, what's the best way to save/restore as much as possible?
Thanks
Click to expand...
Click to collapse
Boot into CWM and make a backup or use Titanium backup to make a backup.
I did use CWM, but it said it backed up "data", which to me means it wasn't a total image with the ROM and apps.
backup
retiredrobb said:
I did use CWM, but it said it backed up "data", which to me means it wasn't a total image with the ROM and apps.
Click to expand...
Click to collapse
If you do a full backup with CWM, then when you get the new device, BE CERTAIN that you are at the same bootloader version before using that backup. (If you try to use a different BL, then you WILL brick the new device.) However, assuming the same BL version, you can just go into CWM again (assuming you have it installed) and do a full restore. The device should look and act just as it did when you backed it up. Even the ROM will be restored. I do this often when switching between ROMS for reviews, etc.
But, your concern for PAID apps is unwarranted. They are on your Android (Google) account. Even if you get a totally DIFFERENT device, they will show up as paid in the "My Apps" part of the Market. Also, most (???) of the free apps show up on my list.
Most (paid) apps are available to install on as many Android devices as you have (and sign on with the same account). The only exceptions are that some apps are not compatible with certain devices (phone vs tablet, etc) and some developers' license agreements only allow a single install (very few do this).
Best wishes on your replacement. I had the same problem (loose power connector) on my GTab but it was way out of warranty so I had to just solder on an external connector and run wires inside the device. It looks ugly but it works.
bl1.2 to 1.1
I got the gtab back, and it's now on bl1.2 (but still gingerbread), whereas it first came with 1.1, and I rooted it to Gtabcomb. So how do I get it back to 1.1 so I can restore my backup?
Visit this site here.
From there you can download the nvflash package for 1.1 boot loader with CWM pre-installed. Follow the instructions on the site for Code Red (I know you could do yellow but red is safer and you don't want to keep anything currently on the tab anyway.) After the nvflash, instead of installing a new rom, you can go into CWM and restore your backup.
That said, I suggest you don't do this. Most all new development is on the 1.2 boot loader now, even Viewsonic if you call them "developers". Anyway you can restore all your apps, even paid ones, through the market and if you did a Titanium Backup you can restore your data (I don't recommend restoring the apps, just the data after reinstalling from the market). Point is, you are already here (1.2) might as well try something new!
Of course, if you really want your old setup back, you can always try to go back. I personally have never had much luck with backups of any kind and pretty much accept that when I flash or crash, it's time to start over.
retiredrobb said:
So how do I get it back to 1.1 so I can restore my backup?
Click to expand...
Click to collapse
If you want to go back to the 1.1 bootloader I have an easy technique to do that--one that does not involve using nvflash. You will need to have ADB installed, though.
---------- Post added at 08:58 PM ---------- Previous post was at 08:55 PM ----------
DaggerDave said:
Visit this site here.
From there you can download the nvflash package for 1.1 boot loader with CWM pre-installed. Follow the instructions on the site for Code Red (I know you could do yellow but red is safer and you don't want to keep anything currently on the tab anyway.) After the nvflash, instead of installing a new rom, you can go into CWM and restore your backup.
Click to expand...
Click to collapse
Let's not use nvflash for every little problem that comes along, eh? Esp. in this case, when its so easy to switch between bootloader versions.
rajeevvp said:
If you want to go back to the 1.1 bootloader I have an easy technique to do that--one that does not involve using nvflash.
Click to expand...
Click to collapse
And that would be.......?
rajeevvp said:
If you want to go back to the 1.1 bootloader I have an easy technique to do that--one that does not involve using nvflash. You will need to have ADB installed, though.
---------- Post added at 08:58 PM ---------- Previous post was at 08:55 PM ----------
Let's not use nvflash for every little problem that comes along, eh? Esp. in this case, when its so easy to switch between bootloader versions.
Click to expand...
Click to collapse
Noted. Didn't know there was a better/safer method for switching between bootloaders. Most of the guides/info/instructions I have found recommend an nvflash to the stock rom for the bootloader version you want end up on. I follow these guides when switching versions:
Know Thy Bootloader
Gtablet for Dummies
and have never had a problem, so I was only pointing him to information that has always worked well for me. I have never tried the ADB method or the .zip installable method to switch and I didn't want to suggest that he try something I haven't successfully done myself, even if it looks easier.
Anyway please do advise on your ADB method. I still get a little nervous when switching BL versions even after doing it many times over the last year! By the way rajeevvp, thank you for the wealth of information you have posted here on this site.
ext SD won't mount
So I'm back to Bl1.1 and stock ROM, but can't get my backup to work cuz the card with the data won't mount. Now i admit I have some other directories on the card. Is that the problem?
The wife and kids are getting restless!
retiredrobb said:
So I'm back to Bl1.1 and stock ROM, but can't get my backup to work cuz the card with the data won't mount.
Click to expand...
Click to collapse
Have you installed CWM (for the 1.1 bootloader)?
Now i admit I have some other directories on the card. Is that the problem?
Click to expand...
Click to collapse
As long as there is a "clockworkmod" directory-tree in the root of the SD card (internal or external), and CWM recognizes the SD card (depending on the version of CWM, it might not use the external SD card at all), you should be able to do the restore.
If you install CWM-2.5.1.1-bekit-0.8, and the clockworkmod directory is on the external SD card, move that entire directory tree to the root of the internal card. CWM v08 uses the internal SD card for backups and restores.
Or else, you can install CWM-2.5.1.3 from bekit.net, which will use the external SD card if one is detected, and fall back to the internal one otherwise.
---------- Post added at 09:45 PM ---------- Previous post was at 09:40 PM ----------
DaggerDave said:
Anyway please do advise on your ADB method. I still get a little nervous when switching BL versions even after doing it many times over the last year!
Click to expand...
Click to collapse
The ADB method involves flashing VS's stock recovery and then using that to downgrade/upgrade the bootloader using a simplified version of gojimi's downgrade/VS stock upgrade install zip file.
In review, I got a new board installed under warranty cuz of the power pin being bad. Was having trouble mounting the ext-sd.
Anyway, so many hours wasted, but FINALLY got Titanium Backup on it, restored everything, and things were back to normal EXCEPT tons of lockups. Browsing, using apps, didn't seem to matter. Then I remembered I dropping the CPU speed when I first went to Gtabcomb 9 months ago. I think that helped, but in the middle of updating some apps it did it again, and when I rebooted the security pin I had set up didn't work! What next?!?
So obviously needed to reset to factory, but then decided WTH, why not bring this thing up to the highest Android 3 I could. So I'm going to change from bl1.1 to 1.2, and go with Gtabcombover. So my questions are - what's the best way to get to 1.2, and will Titanium be able to restore my backup under 1.2?
Did you do a "wipe data/factory reset" and/or repartition the internal SD card after you installed CWM?
retiredrobb said:
So I'm going to change from bl1.1 to 1.2, and go with Gtabcombover.
Click to expand...
Click to collapse
GtabCombOver has a 1.1 version.
So my questions are - what's the best way to get to 1.2
Click to expand...
Click to collapse
The safest method is to re-install 1.1-3588, then use it to update to 1.2.
Finally, even better than b4
rajeevvp said:
Did you do a "wipe data/factory reset" and/or repartition the internal SD card after you installed CWM?
both; followed Ray Waldo's tutorial
GtabCombOver has a 1.1 version.
I know, but figured I'd go whole hog.
I restored my apps and data with Titanium, and so far all is well.
Thanks for all the support.
Click to expand...
Click to collapse
Hi
Trying to root my table tand get it to work, I have not succeeded something operational yet. I have made a root & CWD sd card, and in the process had backed up my tablet. I copied thgis backup to my PC as I had to try different things with the sd card.
So now I d like to restore (to start afresh) but... I google it around, and dont find any procedure!?
I am sure it is known... and am dummy... but can't invent neither.
I need use those files, because I still can't read .apks and try the apk based nook restore.
How should I go?
Your help appreciated
Thanks, Agnes
Restore method did not work....²
I have found my 3 neurons and realized I could just re do a CWD sd card, do a backup, and then take the card to my PC and add the other backup aside there (they are orgnaized by folders and date)
Then back to the tablet, go CWD / restore... but I only get a MD5 error and it does not want. Same with advanced restore.
I finally found this very simple method from Adam to restore to 1.4.0
http://forum.xda-developers.com/showthread.php?t=1402190
It semt it worked, but then when it starts again... I get the same broken rooted / whatever I have now .
Is your device 16GB or 8GB model? depending on that i can tell you what to do.
16GB model has more development and some modified stock ROMs , i even made 1 of them check here:
http://forum.xda-developers.com/showthread.php?t=1494367
~ Veronica
lavero.burgos said:
Is your device 16GB or 8GB model? depending on that i can tell you what to do.
16GB model has more development and some modified stock ROMs , i even made 1 of them check here:
http://forum.xda-developers.com/showthread.php?t=1494367
~ Veronica
Click to expand...
Click to collapse
Veronica,
You wouldn't happen to have an un-modified stock ROM would you?
LonelyTV said:
Veronica,
You wouldn't happen to have an un-modified stock ROM would you?
Click to expand...
Click to collapse
You want a sotck stock unrooted one? yet you need to reply me if your device is 8GB or 16GB model.
Depending on that i can upload it for you , but later 'cause right now i've got to go.
~ Veronica
lavero.burgos said:
You want a sotck stock unrooted one? yet you need to reply me if your device is 8GB or 16GB model.
Depending on that i can upload it for you , but later 'cause right now i've got to go.
~ Veronica
Click to expand...
Click to collapse
Yeah, an unrooted unmodified stick would be great. I've got a 16gb model.
Thanks.
16Gb device now messed uo....
Hi Veronica, thanks for the reply. I am deseprately in need of expert advice here, instead of guessing and trying...
I have a 16 GB Nook Tablet, that was bought with 1.4.0.
I now seriously again need to make a restore, as I did some bad mismanipulation and my tablet is now out of order:-(
One of my best chance I guess would be use one of the backups I have (I have several copied on my HD), but after I formatted and wrote on my SD card several times (is this the reason?), now when I try restore, I have this MD5 error.
I hope I would not run into other problems, as it seems my prop.build may have changed in the process....!
May I ask you to have a look what I did, and then confirm it would be wise try the restore you provided in the thread?
The history what I did:
- I initially had a 1.4.0 with some tweaks to sideload apps, and could no more sideload with 1.4.2 of course (and that is all I need: be able get Kindle, Le Monde, and few other apps!). I understood I had to root and was ready to try get CM7 on my internal drive, and tried a few things (Rooting with Indirect's method, ...), and could not get it to work, until I got very close:
- I restored 1.4.0 using this thread restore 1.4.0 from Adam Outler. It worked fine and apparently erased some of the problems I had that were previously preventing me to move with rooting etc.
- Then I used Albert Wertz's Backup of a rooted 1.4.0. It worked. It seems it had already OTA bloked (displaying version 9.9.9 or so)
- Then I was to install CM7 using this tutorial from ebook-reader, based on this Celtic XDA thread ("team B") (choosing the internal method) , and used the CWM flasher apk. That is where somewhere I did a mistake: after backing up and erasing all data, I somehow stupidly rebooted and got in trouble, and restored the old B&N I don't know how.
- Willing to go back to stage 1, I tried using the 1.4.0 basic restore from Adam Outler, but that did not work anymore, like if my build.prop had been changed in the process (where?)
It said "assert.failed: getprop ("ro.product.device" = blaze" or something alike.
- Then I got a long powercut (am in Africa) and some sleep
- The worse is, the NOOK does not boot and work anymore at all, it is stuck on "read forever" screen
- The curse is, I cant use other restores I have, it says MD5 mismatch
- I also can't use simple root procedures (with CWM and installing zips), as my basic system seems corrupted.
I guess a proper restore may work if I manage to do it, but I wonder what happened with my prop.build and why it was mentionned up there (was it changed in some of the process) - and whether it will create more trouble.
Your advice will be very precious!
Thanks, Agnes
agnes00777 said:
Hi Veronica, thanks for the reply. I am deseprately in need of expert advice here, instead of guessing and trying...
I have a 16 GB Nook Tablet, that was bought with 1.4.0.
I now seriously again need to make a restore, as I did some bad mismanipulation and my tablet is now out of order:-(
One of my best chance I guess would be use one of the backups I have (I have several copied on my HD), but after I formatted and wrote on my SD card several times (is this the reason?), now when I try restore, I have this MD5 error.
I hope I would not run into other problems, as it seems my prop.build may have changed in the process....!
May I ask you to have a look what I did, and then confirm it would be wise try the restore you provided in the thread?
The history what I did:
- I initially had a 1.4.0 with some tweaks to sideload apps, and could no more sideload with 1.4.2 of course (and that is all I need: be able get Kindle, Le Monde, and few other apps!). I understood I had to root and was ready to try get CM7 on my internal drive, and tried a few things (Rooting with Indirect's method, ...), and could not get it to work, until I got very close:
- I restored 1.4.0 using this thread restore 1.4.0 from Adam Outler. It worked fine and apparently erased some of the problems I had that were previously preventing me to move with rooting etc.
- Then I used Albert Wertz's Backup of a rooted 1.4.0. It worked. It seems it had already OTA bloked (displaying version 9.9.9 or so)
- Then I was to install CM7 using this tutorial from ebook-reader, based on this Celtic XDA thread ("team B"), and used the CWM flasher apk. That is where somewhere I did a mistake: after backing up and erasing all data, I somehow stupidly rebooted and got in trouble, and restored the old B&N I don't know how.
- Wwlling to go back to stage 1, I tried using the 1.4.0 basic restore from Adam Outler, but that did not work anymore, liek if my build.prop had been changed in the process (?)
It said "assert.failed: getprop ("ro.product.device" = blaze" or something alike.
- The worse is, the NOOK does not boot and work anymore at all, it is stuck on "read forever" screen
- The curse is, I cant use other restores I have, it says MD5 mismatch
- I also can't use simple root procedures (with CWM and installing zips), as my basic system seems corrupted.
I guess a proper restore may work if I manage to do it, but I wonder what happened with my prop.build and why it was mentionned up there (was it changed in some of the process) - and whether it will create more trouble.
Your advice will be very precious!
Thanks, Agnes
Click to expand...
Click to collapse
Thanks for post the whole history of what you've done 'cause pfff that saves a lot of time.
Now in this part "after backing up and erasing all data, I somehow stupidly rebooted and got in trouble"
1. Did you get to flash CM7 succesfully
2. When you mention you backed up means you backed up CM7?
3. when you mention erasing all data you mean only wipe data (factory reset) or did you wiped maybe formatted anything else?
4. What method did you use to format your sdcard
Edit: i have a MIUI backup that i made for a guy that could not install it with the other way (install .zip) of the same ROM. So at list try it for now to see what happens, if it works then go ahead and flash back the ROM you want, and always make sure to check the md5 of what you download.
http://minus.com/mwIltnw1I/4f - NT_MIUI_Tweaks_backup.zip | md5: 3518f9a3289ca6e97b569777873b899b
* Uncompress the .zip and put the folder (do not change the name of the folder) in your sdcard and flash in CWM >> backup and restore >> restore
~ Veronica
LonelyTV said:
Yeah, an unrooted unmodified stick would be great. I've got a 16gb model.
Thanks.
Click to expand...
Click to collapse
*This is a flashable .zip:
http://minus.com/mwIltnw1I/5f - NT_stock_1.4.0_B&N_ 16GB.zip | md5: f8ae4f8e88e0ced9f252e9440df3910c
~ Veronica
lavero.burgos said:
Now in this part "after backing up and erasing all data, I somehow stupidly rebooted and got in trouble"
~ Veronica
Click to expand...
Click to collapse
Thanks Veronica. Here is as much as I remember:
1. Did you get to flash CM7 succesfully?
No. While following the procedure, I did some mistake after backing up and before even trying to installing CM7. I did not realize I was in CWM within my existing rooted 1.4.0 (using the .apk), so somewhere I wiped and rebooted... to realize I was rebooting into nothing! Or actually into the original 1.4.0 B&N. And then I did some attempts to go back step by step (like restoring that 1.4.0 from Adam then the rooted 1.4.0 from Albert) and somehow went into more troubles.
2. When you mention you backed up means you backed up CM7?
No, since I did not go so far as to install CM7.
I have a backup of my initial (tweaked) 1.4.2 system, then one of Albert rooted 1.4.0 (not mine), then another one of a Nook normal OS that worked (not sure, I think 1.4.2) at some point later.
These backups were OK, I used at some point, I don't understand why then I got this MD5 errors.
3. when you mention erasing all data you mean only wipe data (factory reset) or did you wiped maybe formatted anything else?
I used the command within CWM, both to wipe data and cache
4. What method did you use to format your sdcard
I usually use Acronis Disk Manager, a quite powerful programme to change partitions on disks and also handle formatting. When I really want to make sure, I first use HP USB formatting tool, and then sometimes check on Acronis to get the partitions I want. I am not sure in what order I did that time, but was not using partitionning in fact.
I will redo it all again as I wonder if it is not a mistake on the disk that lets it misread the MD5, as I think my backups were fine.
I don't undestand:
- why my MD5 are wrong, and is it something I can fix by properly reformatting mys disks
- what is this story with "assert.failed: getprop ("ro.product.device" = blaze" and where I may have changed the build.prop. Is it somehting that will bother me further or should push me into one direction rather than another.
I will try your MUI backup. (What means MUI?). (It may take ma a day or 2 to download this through Lesotho poor internet :-(
Thanks and wil tell you what happens!
agnes00777 said:
Thanks Veronica. Here is as much as I remember:
1. Did you get to flash CM7 succesfully?
No. While following the procedure, I did some mistake after backing up and before even trying to installing CM7. I did not realize I was in CWM within my existing rooted 1.4.0 (using the .apk), so somewhere I wiped and rebooted... to realize I was rebooting into nothing! Or actually into the original 1.4.0 B&N. And then I did some attempts to go back step by step (like restoring that 1.4.0 from Adam then the rooted 1.4.0 from Albert) and somehow went into more troubles.
2. When you mention you backed up means you backed up CM7?
No, since I did not go so far as to install CM7.
I have a backup of my initial (tweaked) 1.4.2 system, then one of Albert rooted 1.4.0 (not mine), then another one of a Nook normal OS that worked (not sure, I think 1.4.2) at some point later.
These backups were OK, I used at some point, I don't understand why then I got this MD5 errors.
3. when you mention erasing all data you mean only wipe data (factory reset) or did you wiped maybe formatted anything else?
I used the command within CWM, both to wipe data and cache
4. What method did you use to format your sdcard
I usually use Acronis Disk Manager, a quite powerful programme to change partitions on disks and also handle formatting. When I really want to make sure, I first use HP USB formatting tool, and then sometimes check on Acronis to get the partitions I want. I am not sure in what order I did that time, but was not using partitionning in fact.
I will redo it all again as I wonder if it is not a mistake on the disk that lets it misread the MD5, as I think my backups were fine.
I don't undestand:
- why my MD5 are wrong, and is it something I can fix by properly reformatting mys disks
- what is this story with "assert.failed: getprop ("ro.product.device" = blaze" and where I may have changed the build.prop. Is it somehting that will bother me further or should push me into one direction rather than another.
I will try your MUI backup. (What means MUI?). (It may take ma a day or 2 to download this through Lesotho poor internet :-(
Thanks and wil tell you what happens!
Click to expand...
Click to collapse
Try formatting your sdcard again, i recommend SDFormatter. Sometimes sdcard can be the cause of many weird errors and issues.
Then copy back one of your backups within clockworkmod >> backup folder
If no go with that then try the following.
* First you need adb working
Here is a tutorial i made about it: http://forum.xda-developers.com/showpost.php?p=22049356&postcount=1
* Plug your NT to your PC using USB cable
* Download the file attached which is 1.4.0 stock build.prop, uncompress it, put it in the same folder adb is located and push it using adb while in CWM
> cd path-of-adb-tools
> adb devices
(verify that you get a code with numbers and letters)
> adb remount
(if this command does not work for you then please mount /system manually from mount&storage > Mount /system in CWM)
> adb push build.prop /system
* Unplug cable
* Try Adams acclaim_update.zip again ( preferably with nothing else in your sdcard only that .zip
* Report back
~ Veronica
OK I now was finally able to download the files.
- I guess I'll try first what you suggested with the MIUI backup after a proper reformat.
(I am just not sure which CWD file to use, as many dont leave any space on the card to put backups....)
- Then the ADB method if the 1st one does not work.
Though, part of the ADB tutorial is this "ADB root hijack" where they say you must already be rooted - that is not my case....
I'll try do tomorrow... and report! So glad to have your help here.
Successfully restored MIUI backup... what next?
YES!
@Veronica, I have been able to restore your MIUI backup!
I am not sure what it is... it looks like for a phone.... but it seems Market is working YEAH! 1st time on this Nook!!!!
Veronica you are a queen !!!
May I ask you what should be my next step now?
As a reminder, I basically want to get here Kindle (because I bought this Nook for Xmas for my Mozambican husband without realizing B&N does not have any Portuguese books, while Amazon does) and a few more apps I like. So this would do! But I d like make sure:
- my system is more or less stable
- I don't get messed up with more OTA updates
So I wonder:
- is this system recommendable? This is rooted, right? Should I prefer Launcher or Zeam Launcher here?
- should I rather use another system? Go into CM7?
Since I dont have even any Nook here behind, I am afraid of more troubles following the normal procedure, should I?
- Do I need at all to set the normal version of Nook behind (like I could use with the Nook button app) - in fact, I don't really care...
HELP PLEASE!!!! Nook 8Gb!
Can somebody help me? I bricked my nook tablet 8Gb!!
This is the whole story:
1) Rooted my NT
2) Used this apk to install CWM
http://forum.xda-developers.com/showthread.php?t=1458630
3) Tried to flash CyanogenMod 7 ROM but while it was flashing the tablet blacked out and rebooted
4) Now the tablet is stuck at the READ FOREVER screen
5) I can boot in CWM holding power+N button, but it can't flash anything, it freezes anytime I try to flash something.
6) I followed these 2 guides to unbrick my NT but they didn't work
http://forum.xda-developers.com/showthread.php?t=1470910
http://forum.xda-developers.com/showthread.php?t=1562130
Can anyone help me restore my NT at least to stock???
Please I'm desperate!!!!
@JohnDorian, Seems you got very similar problem to mine...!
It seems we got the same problem trying to do the same thing... So the same solution may work? (the only difference beeing I have not tried the unbrick mehods you did)
What I just did with Veronica's guidance, and worked for me:
- I created a 50MB sd card to boot into CWD, using this
- booted into CWM with it
- copied onto another SD card the MIUI backup Veronica provided earlier in this thread:
http://minus.com/mwIltnw1I/4f - NT_MIUI_Tweaks_backup.zip | md5: 3518f9a3289ca6e97b569777873b899b
- inserted it and did restore. It just worked and provided something that seems acceptable!
And at least, next steps may be possible...
I hope it works with you too!
Thank you for your answer!
Will this work also with my 8Gb NT?
agnes00777 said:
YES!
@Veronica, I have been able to restore your MIUI backup!
I am not sure what it is... it looks like for a phone.... but it seems Market is working YEAH! 1st time on this Nook!!!!
Veronica you are a queen !!!
May I ask you what should be my next step now?
As a reminder, I basically want to get here Kindle (because I bought this Nook for Xmas for my Mozambican husband without realizing B&N does not have any Portuguese books, while Amazon does) and a few more apps I like. So this would do! But I d like make sure:
- my system is more or less stable
- I don't get messed up with more OTA updates
So I wonder:
- is this system recommendable? This is rooted, right? Should I prefer Launcher or Zeam Launcher here?
- should I rather use another system? Go into CM7?
Since I dont have even any Nook here behind, I am afraid of more troubles following the normal procedure, should I?
- Do I need at all to set the normal version of Nook behind (like I could use with the Nook button app) - in fact, I don't really care...
Click to expand...
Click to collapse
Hello im glad to see you're back, about launchers, addons & apps it all depends of your likes.
What i gave you is MIUI ROM (operative system) without major modification (as-is) and yes it has zeam launcher but all can be modified.
I'm personally not a fan of gingerbread CM7 because i really like the eye candy of MIUI and even stock (which the buttons and menus are very similar to MIUI) so i use MIUI.
About stock i didn't mind using it even though i don't use B&N application and buy books from them buy i enjoyed the eye candy (interface/GUI), now that @cobrato released MIUI i immediately switched to that as im a huge fan of MIUI.
I have always used GO launcher as my main launcher but now im starting to use ADB in MIUI because it manages better the grid feature.
All systems you're going to find already come rooted which is standard and is the feature #1 of custom and stock ROMs, without root there is no fun. If you're in this community is because eather you have a rooted device or you came to learn how to root it and other stuffs.
If you like B&N stock ROM but don't use their apps and services you can bypass the registration and forget about the OTA updates, you can also apply on top of that the OTA block with titanium backup if you want to make sure. That is the methods i used and never ever had a problem. I also recommend you that when you flash a stock ROM do the whole procedure of OTA block and don't guess is already blocked, nothing better than do it yourself manually.
If you decide you want to make use of B&N services then you can eather go back to stock for a complete B&N experience or just install their app from the market if you're on CM7, CM9 or MIUI that is, nothing fancy but it does the job.
I have mentioned days ago that i was going to make a thread for MIUI users with how-tos and info about set it up but i've got very busy with many bricked devices around lol, but i eventually will do.
~ Veronica
---------- Post added at 02:58 PM ---------- Previous post was at 02:56 PM ----------
JohnDorian said:
Thank you for your answer!
Will this work also with my 8Gb NT?
Click to expand...
Click to collapse
no, it is only for 16GB tablet, let me read your problem
~ Veronica
---------- Post added at 03:06 PM ---------- Previous post was at 02:58 PM ----------
JohnDorian said:
Can somebody help me? I bricked my nook tablet 8Gb!!
This is the whole story:
1) Rooted my NT
2) Used this apk to install CWM
http://forum.xda-developers.com/showthread.php?t=1458630
3) Tried to flash CyanogenMod 7 ROM but while it was flashing the tablet blacked out and rebooted
4) Now the tablet is stuck at the READ FOREVER screen
5) I can boot in CWM holding power+N button, but it can't flash anything, it freezes anytime I try to flash something.
6) I followed these 2 guides to unbrick my NT but they didn't work
http://forum.xda-developers.com/showthread.php?t=1470910
http://forum.xda-developers.com/showthread.php?t=1562130
Can anyone help me restore my NT at least to stock???
Please I'm desperate!!!!
Click to expand...
Click to collapse
I don't have a 8GB nook tablet to upload a backup of stock ROM and actually is very important to have nobody has been nice to upload it and post it in development section. Anyway let me give you the link of the official update to see if that helps, i was checking yesterday and they provide one for both i think there is not a separate section for the 8GB model so i assume that update is for both models containing 1.4.2
http://www.barnesandnoble.com/u/Software-Updates-NOOK-Tablet/379003187/
under -Get Version 1.4.2 Today
~ Veronica
How can I flash this update?
JohnDorian said:
How can I flash this update?
Click to expand...
Click to collapse
right you dont know how, ok let me download the file and see if i make a kind of acclaim_update.zip for you to try.
can't flash any rom as a flashable.zip and backup folder? have you tried both?
~ Veronica
No, I can't flash anything from CWM...
Hello,
I've installed CM internal to (2) NT 16GBs without incident, and I got stumbled by the n button not working with 1.4.1 that was on my third. Ultimately - I downgraded to 1.4.0, installed CM7, and then did the dumb thing.
I meant to hit wipe data and cache, and I clicked factory reset in CWM. (And at this point - it is stuck in a state where I can boot to CWM - but cannot get CM7 to boot in any form from the internal rom).
I attempted the following
1) acclaim restore (just tried didn't do anything)
2) backup / restore from alternate nook Tablet 16Gb (man this seemed promising ...)
3) couple of the different unbrick scenarios - but I don't have adb, and it seems like windows 7 is not a happy camper with nook usb devices, (and adb isn't happy either.)
4) meghd00t restores (couple of different variations.)
does anyone have any starter threads that I should start walking down for the same stuff - I have browsed, and it's been a couple of hours and I'm exhausted. will poke back in tommorow, and will get this thing plugged into a linux host.
It didn't seem like adb could be so hard ...
--Adrian
Hmmm interesting... ok first of all doing this "I meant to hit wipe data and cache, and I clicked factory reset in CWM" is not dumb is ok to do but is not good signal the hang actually is very weird. Maybe all you have is a corrupted cwm recovery flash. Now be explicit if you indeed could try some unbrick methods succesfully (the ones running from sdcard) and what methods exactly did you try.
~ Veronica
things I've tried - part 1
1) just try to restore to factory with acclaim_update.zip on non-booting sdcard , (this is the 1.4.0 image) - I get the grey n, a flash of white - (like it's going to boot), and that that "please restart your device and try again..."
(This worked when it was factory), but it seems like the logic to check the sd card and start to recover isn't working.
2) Tried the thread here - http://forum.xda-developers.com/showthread.php?t=1562130 - meghd00tr4-sdimg.zip boots, but first time - get red reverse highlighted line - "booti: bad boot image magic in memory" - s5 in the upper left corner of the cyanoboot screen, and the n button doesn't seem to do anything.
3) same thread different image - repart.img, this runs fine- and after about 30 seconds of boot, I get a green check, (waited a full (2) minutes after that green check before I unplugged it.) - same message after boot.
4) full restore of nook tablet from current good cm7 image (and this is the one that most concerns me) - NT16gbV4_6 based cwm v5.5.04 - attempting restore of backed up alternate nook tablet - and the exact same thing happens at boot - does the image not touch partions that aren't related to the root install -(this seems like maybe there is something the bootloader is looking for in the image that isn't right, and it wedges?)
I am going to work on getting an adb setup going that works and then start working down a couple of fix recovery scenarios today / tonight.
It doesn't seem like this is unrecoverable - and the worst part is -I had cm7 booting fine for a couple of reboots, and then something went awry.
--Adrian
as I think about this ...
I do have (2) differnt backups, and I wonder if that restore was the wrong thing to do.
I got to thinking this as I saw the restore of the .android_secure file, from the ALTERNATE nook. I have the backup from the 1.4.0 "original working" image of this nook before the cm 7 issues- but I put it on an SD card that is safetly out of my reach. (In a friends cell phone.)
I think an easy thing will be to restore that backup as another test.
-Adrian
peril said:
I do have (2) differnt backups, and I wonder if that restore was the wrong thing to do.
I got to thinking this as I saw the restore of the .android_secure file, from the ALTERNATE nook. I have the backup from the 1.4.0 "original working" image of this nook before the cm 7 issues- but I put it on an SD card that is safetly out of my reach. (In a friends cell phone.)
I think an easy thing will be to restore that backup as another test.
-Adrian
Click to expand...
Click to collapse
Right, try that first, dont attempt anything advanced yet. Your problem could be solved easily
Just to make sure you flashed cwm from @Indirect app?
~ Veronica
Sent from my Nook Tablet using xda premium
Wait, can you boot into a CM7 SD ROM? From there you could try reflashing recovery.
Sent from my R800x
FIXED
I used this method - and I was good to go.
http://forum.xda-developers.com/showthread.php?t=1470910
In one of the flashes - must have hit the power prior to something being complete with the recovery.
thanks all for your support - and really appreciate the time in the forum. I'm going to put together a torrent with the recovery stuff in it, and make sure it's available as my little part. (Give me a day or so.)
Thanks again.
--Adrian
The problem with that is that you will lose your original serial ID's and MAC address if you didnt backup your rom partition (mmcblk0p5) first so if you use B&N services you wont be able to register after flash any stock rom.
~ Veronica
Sent from my Nook Tablet using xda premium
I also screwed up...Reverting to 1.4.0
Tried to revert to 1.4.0, and followed all instructions as showned on a youtube video. Unfortunately, as it was reverting back to older version as soon as it finished the process - the tablet wouldn't start back up. Did any one ever have this happen to them.. Fortunately, I had just bought today at WalMart. So, I'm going to replace it...
Was just curious, if it ever happened to any one. If so what did I possibly do wrong....
mr_truevision said:
Tried to revert to 1.4.0, and followed all instructions as showned on a youtube video. Unfortunately, as it was reverting back to older version as soon as it finished the process - the tablet wouldn't start back up. Did any one ever have this happen to them.. Fortunately, I had just bought today at WalMart. So, I'm going to replace it...
Was just curious, if it ever happened to any one. If so what did I possibly do wrong....
Click to expand...
Click to collapse
Hmm i think you have a 8GB Nook Tablet and the acclaim_update.zip is only for 16GB NT.
~ Veronica
ubuntu recovery.
This was strictly for CM7. I have no problem with being locked out of the B&N services. (I use the nook application for that access.)
Wish I would have known the serial number before / after. I was able to login to my B&N account after 1.4.0 was restored from ubuntu.
--Adrian
lavero.burgos said:
The problem with that is that you will lose your original serial ID's and MAC address if you didnt backup your rom partition (mmcblk0p5) first so if you use B&N services you wont be able to register after flash any stock rom.
~ Veronica
Sent from my Nook Tablet using xda premium
Click to expand...
Click to collapse
I was trying to flash this thing back to stock to sell to someone from CM7, and for some reason, it seems like I'm bricked. Here's the method I used:
http://forum.xda-developers.com/showthread.php?t=1663836
I did everything step by step up until:
"Now DONT do anythign to your Nook - Just sit back and relax
Once Nook finishes installing IMG, a "Green Checkmark" will appear on top right hand corner
Remove your SD card from your Nook Tablet
You will see Nook will restart itself"
I didn't see a green checkmark, I saw a red x instead. Would this be the problem? I redownload the img a few times now and tried this a few times, so I'm kind of giving up. It won't boot up at all unless I have the card in and it doesn't boot past what's described above.
I tried to use this method as well:
http://forum.xda-developers.com/showthread.php?t=1470910
But the download said it had reached it's limit for the day. I can try it if someone has a mirror?
Try https://github.com/succulent/acclaim_recovery_sdcard, see its README file for an annotated index/description of the resource/tools and usage instructions. See also http://forum.xda-developers.com/showpost.php?p=37515697&postcount=31 before selecting some "unbricking" tool.
No luck yet ugh
1000cleverlines said:
No luck yet ugh
Click to expand...
Click to collapse
If the repart image didn't work you have a few options. Use the Adam Outlers Ubuntu Total ReFlash Method to try and recover the stock operating system. If that doesn't work than maybe you erased some important information such as serial number etc. Take it to Barns and Noble for fixing.
Finally got the Ubuntu recovery to download, i'll report back if it works.
taking it back to b&n probably isn't an option. it's over a year old, so i think that would make it out of warranty, but correct me if i'm wrong.
datallboy said:
...
Use the Adam Outlers Ubuntu Total ReFlash Method to try and recover the stock operating system. If that doesn't work than maybe you erased some important information such as serial number etc.
...
Click to expand...
Click to collapse
FWIW, the /factory partition which gets wiped by AdamOutler's "Ubuntu Total Wipe & Reflash" contains backup copy of the NT device-specific data such as serial number, WiFi MAC address, etc., in archive format (romdata.zip) -- and there is no indication in Adam's post that this data gets saved (for later reflashing) before the partition gets wiped.
Hey guys iam new to this whole rooting and jailbreaking but ever since I read about it I realy want to do it so I tryed it on my NT and in the last step it my NT didnt want to read my sd chip so I was stuck in boot mode so I just hit the factory reset and everthing was fine but when I turned it back on 2 days ago I got a please restart your device and try again if encounter again call customer support so I tryed the method he described above but I got green check mark but when I took out my sd chip the same error message pops up help will be greatly appceated thx.
Sent from my HTC Glacier using xda app-developers app
On the Adam Outler post is says.
"So, as a result of my work, I would like to present the first ever Ubuntu Recovery. This will totally wipe your device. With the exception of the ROM Partition which contains serial information, every single partition will have zeros written to it then flashed with just enough to preform an initial recovery reflash. Normally when you preform an update or flash the device, it is simply formatted. A formatted device can be unformatted. A zeroed device cannot be unformatted. All information is overwritten with zeros."
The Ubuntu recovery tool won't flash over the serial number. Only write zeros over the current partitions and attempt to reformat your system correctly.
If the ROM partition is gone( meaning serial number, Mac address etc) the options are to somehow recover and flash a ROM partition onto the Nook (which would be a problem if multiple people had the same information) or take it to Barns And Noble.
So in other words am screwd I dont know how to flash is there a tut on flashing cwm file and what are some good free flash programs
Sent from my HTC Glacier using xda app-developers app
Go to the Nook Tablet General forum. There are tutorials for setting up CWM recovery and ROMS.
The Ubuntu unbrick tool worked.
1000cleverlines said:
The Ubuntu unbrick tool worked.
Click to expand...
Click to collapse
Alright! (If you dont mind helping me out) How did you get it to boot from the SD card? I've made a Ubuntu Card in hope of just testing out the operating system, but it won't boot from the SD. Tried plugging in the USB and waiting, but nothing. Tried without and booted to stock. Any extra steps involved?
K thx hopefully ill get it
Sent from my HTC Glacier using xda app-developers app
datallboy said:
On the Adam Outler post is says.
"So, as a result of my work, I would like to present the first ever Ubuntu Recovery. This will totally wipe your device. With the exception of the ROM Partition which contains serial information, every single partition will have zeros written to it then flashed with just enough to preform an initial recovery reflash. Normally when you preform an update or flash the device, it is simply formatted. A formatted device can be unformatted. A zeroed device cannot be unformatted. All information is overwritten with zeros."
The Ubuntu recovery tool won't flash over the serial number. Only write zeros over the current partitions and attempt to reformat your system correctly.
Click to expand...
Click to collapse
The /rom partition contains the working copy of the NT device data (factory installed device info (ProductID, manufactured data, etc.) and individual device data (serial no., MAC address, security encryption keys, etc.)), and the /factory partition contains the backup copy of the same data and well as the stock ROM in zip archive format, which are to be used by the stock recovery to restore the NT to factory fresh condition.
So, although Adam's tool itself does not zero out the /rom partition, its content is still subject to loss/corruption due to stock recovery's process of automatic reformatting and re-flashing the /rom partition with a non-existent (or possibly Adam NT's?) backup copy -- as it attempts to restore the NT to factory fresh condition.
If the ROM partition is gone( meaning serial number, Mac address etc) the options are to somehow recover and flash a ROM partition onto the Nook (which would be a problem if multiple people had the same information) ...
Click to expand...
Click to collapse
No kidding!!!
... or take it to Barns And Noble.
Click to expand...
Click to collapse
Good luck with that, especially if the NT is out of warranty.
A LOT of people have been asking the same questions pertaining to unbricking the Nook Tablet. This is for anyone who gets "The Red "X"", or "E:/ Can't Mount" Errors. If you have these problems use these methods in the order they appear.
FOLLOW ALL METHODS AS DIRECTED! ROOT AND FLASH ROMS AT YOUR OWN DISCRETION
Step 1) Wipe to factory reset. Wipe cache, wipe dalvik cache. Reflash the ROM via CWM 6.***
Step 2) Use the Repart Image in attempt to reflash stock B&N OS
http://raywaldo.com/2012/06/how-to-un-brick-a-nook-tablet-8gb-or-16gb/
Step 3) Follow the instructions given here
http://forum.xda-developers.com/showthread.php?t=1513583
Step 4) Albert’s Method: Make the R3 Card
http://forum.xda-developers.com/showthread.php?t=1528625
Step 5) Install Adam’s Method (MAC Address and S/N are in danger of being lost. ONLY AS LAST RESORT! S/N and other information is on your device. S/N on the SD slot, MAC address inside the device.)
http://forum.xda-developers.com/showthread.php?t=1470910
If none of these methods work for you then you have probably screwed up your tablet pretty bad (deleted ROM partitions.) Unless you have a backup with all S/N, MAC Address, ProductID, DeviceID etc. you may be out of luck. These methods only go so far.
No Hope?
datallboy said:
If none of these methods work for you then you have probably screwed up your tablet pretty bad (deleted ROM partitions.) Unless you have a backup with all S/N, MAC Address, ProductID, DeviceID etc. you may be out of luck. These methods only go so far.
Click to expand...
Click to collapse
So there is no Hope if you deleted Rom partitions? nothing left to do than throwing your nook? cant ypu use someone else's backup to unbrick your tablet or so?
djjean19 said:
So there is no Hope if you deleted Rom partitions? nothing left to do than throwing your nook? cant ypu use someone else's backup to unbrick your tablet or so?
Click to expand...
Click to collapse
If someone has a backup of their device it won't help because you lose MAC address and information for YOUR device. You can't have multiple devices with the same Product ID and MAC address etc. These methods are meant to recreate the partitions by writing zeros. If I find other methods I will add them to the list.