I root xperia x10 and I installed xrecovery,today I tried to run this rom FeraLab*** v14.2 ~Volt and after that is stuck on boot,i can not run download mode too.
please what to doo?
Are you unlocked bootloader and flash kernel
no,i made a mistake. i think that something is going on with update service.mybe will repair a phone .
yeeeeeeaa it is working again
You can flash the offical room to slove this problem but you need remember the room you flash should suitable for your baseband and you can search it in here.I want to send it to you but now I need sleeping hehe .Good Luck
---------- Post added at 11:32 PM ---------- Previous post was at 11:31 PM ----------
Congratulation hehe
android version is 2.3.3
baseband 2.1.71
kernel 2.6.29-00054
and i unlocked bootloader with flash tool
what to do
crosmurf said:
android version is 2.3.3
baseband 2.1.71
kernel 2.6.29-00054
and i unlocked bootloader with flash tool
what to do
Click to expand...
Click to collapse
What u looking to do exactly pal?
Sent from my X10S using XDA
I want to put rom file in the phone and I almost destroy it.
U need to download the Rom of choice to your pc. Then u need to copy it somewhere onto your sd card that is easily located (personally I have go oder on my sd called roms so I put them there). Then u must boot into recovery and install the zip from where u placed it on sd card. If u not sure bout anything I said let us know I'll explain in more detail if u need
Sent from my X10S using XDA
I made it all but it will not work properly,I think the problem is with kernels.After boot stays frozen.I change the rom to update.zip and then i use xrecovery.
U don't need to change to update.zip just select install custom zip then go to sd card and find it
Sent from my X10S using XDA
do i need to change a kernel?You say that I only need to copy any rom on the SD card.means that i only need to find with xrecovery at custom zip that rom and that is it.Now I will try again
Flash global generic firmware pal and start again I'd say
Sent from my X10S using XDA
which sw to use
Tell you how to install v14.2 in right way
Hi friend . If you want to use V14.2 Rom follow those. In all the steps before you need make sure your x10 is unlocked bl (important) .First you need flash kernel suitable for V14.2 (u can find it in where you download Rom ,The recover have been merged into kernel .I think you can't open xrecover now because you install it in the Rom ,you can't open xrecover in a new rom without it .if you flash kernel bring xrecover ,that means you can use it in any rom hehe) Then open cwm recover install V14.2 Rom in you sdcard (I think it still in you sdcard if you didn't delete it ) Tha's all .Now you can use V14.2 .Enjoy
If I were you Id use pcc/seus and go back to stock.Then look at Crowds guide,follow it and unlock bl.
I run Feras v14.2 and everything works fine
Posted using s2 by xda premium
stuck on boot tried flashing it a few times but does not want to work can someone help???
Rubz21 said:
stuck on boot tried flashing it a few times but does not want to work can someone help???
Click to expand...
Click to collapse
Flashed what?
Sent from my GT-I9300 using XDA
Related
Hi all senior xda-developers XD
I'm new on Android.
I'm using SE Xperia Neo running GingerBread 2.3.4 build 4.0.2.A.0.62 with unlocked bootloader without root.
I try to installing Cyanogen 7 on my Neo but it always failed just reboot, reboot, reboot and reboot..
I have follow the wiki on the Cyanogen site when installing it, i try it 2 times and got the same result so i relock the BL and back to original stock firmware
Can someone tell me what's going wrong? or should i root it first before installing Cyanogen?
Have you flashed kernel with fast boot yes
Sent from my MT15i using xda premium
No, because i don't know how to flash kernel and it is not on the Cyanogen installation wiki.
So, i need to flash the kernel first?
drafha said:
No, because i don't know how to flash kernel and it is not on the Cyanogen installation wiki.
So, i need to flash the kernel first?
Click to expand...
Click to collapse
Here you go!Follow those step and you get cm7
So, "flash new kernel (always use the kernel provided in CM7 / it is incompatible with stock ROM)
ON PC - run fastboot flash boot boot.img (an black window will open and will stay open untill kernel is flashed)" this step is called flash kernel?
I've done it.. It said extract the CM7 packed and place the boot.img file on the same folder with Fastboot then run the command.
I just forgot whether i have wipe the data or not XD
Btw sorry for my english..
Anyway i read this:
" Hi all
Am a newbie in android things n just read here n there for info bout rooting
So i have a few things to clear out if some1 can help me sort out
1: Do i have to root my se neo if i wana put cm7 ?
2: Does rooting mean i can delete useless apps (not added ones nor dwnloaded ones) frm the firmware so that i can free rams in ma fone?
thx 4 reply
Hello
1.yes you need to root and unlock boot loader to use cm7
2.yes,after rooting using file manager like Root explorer you can delete unwanted apps aka bloatware"
So, if he true. I need to root my Neo first before installing CM7 on my Neo?
drafha said:
Anyway i read this:
" Hi all
Am a newbie in android things n just read here n there for info bout rooting
So i have a few things to clear out if some1 can help me sort out
1: Do i have to root my se neo if i wana put cm7 ?
2: Does rooting mean i can delete useless apps (not added ones nor dwnloaded ones) frm the firmware so that i can free rams in ma fone?
thx 4 reply
Hello
1.yes you need to root and unlock boot loader to use cm7
2.yes,after rooting using file manager like Root explorer you can delete unwanted apps aka bloatware"
So, if he true. I need to root my Neo first before installing CM7 on my Neo?
Click to expand...
Click to collapse
You need ONLY UNLOCK bootloader. Thats all.
taaviu said:
Here you go!Follow those step and you get cm7
Click to expand...
Click to collapse
If we disperse information in several threads we really are not helping others. Please post in existing threads, and read this before open a new thread. Thread closed.
hey guys please some help
i wanted to install a custom rom
now im stuck
i did this
rooted via flastool
cwm5 via flash tool
i have 2.1 at the moment
after that to install the rom i was advice to install the kernel v6
i did
after that i install the recovery v6 for gb
i did
booted in recovery and installed the rom
myfirstrom.zip
and now im stuck
what can i do to fix this
thanks
Wrong thread buddy
Sent from my X10i using xda premium
elmanortega said:
hey guys please some help
i wanted to install a custom rom
now im stuck
i did this
rooted via flastool
cwm5 via flash tool
i have 2.1 at the moment
after that to install the rom i was advice to install the kernel v6
i did
after that i install the recovery v6 for gb
i did
booted in recovery and installed the rom
myfirstrom.zip
and now im stuck
what can i do to fix this
thanks
Click to expand...
Click to collapse
This tread should be in Q&A not in DEV.
Anyway do U have bootloader unlocked?
That rom is a 2.3 rom and you need to have and unlocked bootloader. You need to have 2.3 on your device first which would you would find in my signature below. So skip through the tread and find 2.3 Download it and flash it and try the rom again.
Sent from my X10i
Dude u r in 2.1 now. It has a baseband of .49 or .54. GB needs a baseband of .71. So the only option is first u download a pre-rooted firmware image and flash it via flashtool. U will boot into GB. Then unlock bootloader using Laser's method and install custom kernel like DoomKernel.
Follow this method
[RECOVERY image] {v2} X10 GB 3.0.1.G.0.75 [Prerooted + Fixed xRecovery] to insatll the prerooted firmware using flashtool.
Unlock bootloader using this steps from
[HOW-TO]UNLOCK bootloader for X10
Then flash DoomKernel from this link
[KERNEL][X10] DooMKernel [UNLOCKED BOOTLOADERS]{Rel:v06}[Dt:10/Jan][FW3.0.1.G.0.75] and boot up into stock rom or the previous GB rom u r using.
For Stock based roms, DoomKernel is simply the best.
For CM7 based roms, use FXP 130 kernel provided here FXP 130 and
For CM9 based roms, use FXP 132 kernel for better performance which u can download in FXP CM9 Thread.
---------- Post added at 11:10 AM ---------- Previous post was at 11:08 AM ----------
kingstonxl said:
This tread should be in Q&A not in DEV.
Anyway do U have bootloader unlocked?
Click to expand...
Click to collapse
He hasnt even updated to GB.. Still in stock 2.1.
Don't scare the guy with laser's method for now he is starting out small like we at one time were(im still growing) , the latest version of flashtools could do it easy. Its all in my signature if you tries it.
Sent from my X10i
brenty108 said:
Don't scare the guy with laser's method for now he is starting out small like we at one time were(im still growing) , the latest version of flashtools could do it easy. Its all in my signature if you tries it.
Sent from my X10i
Click to expand...
Click to collapse
Sry i didn kw ur post.. Let him do the way he think is best
thanks guys
im downloading the 2.1 ans 2.3 roms
now how do i install them?
i can access xrecovery
but when i connect to flashtool i dont have all the options
actually none
the devices is detected but thats it
can a stock rom be install using xrecovery?
elmanortega said:
thanks guys
im downloading the 2.1 ans 2.3 roms
now how do i install them?
i can access xrecovery
but when i connect to flashtool i dont have all the options
actually none
the devices is detected but thats it
can a stock rom be install using xrecovery?
Click to expand...
Click to collapse
dude flashing option works only when u r in download mode. i think u have 2.3.4. and stock kernel. if u want custom roms u have to unlock bootloader shown u n the post i provided
a2441918 said:
dude flashing option works only when u r in download mode. i think u have 2.3.4. and stock kernel. if u want custom roms u have to unlock bootloader shown u n the post i provided
Click to expand...
Click to collapse
thanks
Originally Posted by Androxyde
X10i Generic
Generic version 2.3.3 build 3.0.1.G.0.75 (MD5: 36F52BAA3556CDD7E56383614C01E5D6)
this one is no longer available
Thread Moved
You should Know better, your post count indicates you have been active, so should be fully aware of the rules
after i connect in flash mode
it stays for a few secs and reboots into the sse screen
is there a way to install the oem rom
in xrecovery?
or a 2.1 rom in recovery?
if i install a 2.1 custom rom
will that help??
im connected to flashtool in flash mode but nothing no options
what do i do now?
ok i finally go it to
where it was suppose to be to install formware
and this is where i am
Did you click fastboot? Click flashmode as x10 doesn't fastboot lol
Sent from my Xperia X10 using xda premium
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
If that rom is in ftf format
Open with 7zip or winrar
Look for kernel.sin
And place it in a folder
In flashtool create kernel
Point it to the folder containing kernel.sin
You should then be able to place your created kernel into firmware folder and flash it
I haven't had much experience with those roms so it's just a suggestion
Sent from my Xperia X10 using xda premium
elmanortega said:
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
Click to expand...
Click to collapse
You need to install a kernel called fxp132 from team fxp for ICS ROM to work... see my other posts in Q&A.. I have uploaded it somewhere.. you should be able to access through my profile->-> posts.
Sent from my Transformer TF101 using xda app-developers app
elmanortega said:
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
Click to expand...
Click to collapse
hey friend, you have downloaded the xperia s ics by vassishta but you dont know what kernel to be used?, dont be so lazy reading all the stuff in that thread (i mean xperia s ics), fxp 132 kernel is included there and instructions on how to flash the rom, hope i helped you, please press thanks button for me, pressing it is just an easy thing.. cheers.. :good:
Folks, someone please help me out.
desperate situation here.
Xperia mini 15sti : rooted, unlocked bootloader, busyboxed, RecoveryX installed (version for 2.3.4) - firmware 4.0.42 version : gingerbread
None of the ROMs I've downloaded have worked so far. Everything results in an error or another. It is incredible how difficult I'm finding this to be.
CM10 : gives me assert errors. Saying its not smultron. I've removed the assert check in updater, then it starts giving me installation aborted after some time.
CM9 : same assert error
ParanoidAndroid : symlink errors during installation
AOKP : installation fails with set path something
I've spent countless hours on finding out the root cause of my problem - but given that everything fails, I am guessing there is something elementary that is missing (or wrong in my approach)
I'm on android gingerbread, and trying to jump to either JB or ICS nothing really works here (I follow the usual wipe data cache everything with every single install attempt so far. And then start with rooting flashing firmware back to 4.0.42, then recoverX, then new ROM etc)
please help
Dhruv
Did you unlock your bootloader? If you haven't unlocked your bootloader none of the above mentioned Roms will work with you. (after unlocking the bootloader you need to flash a custom kernel according to the Rom you are flashing, via fastboot).
See this
Press thanks if I helped you
Sent from my ST15i using xda app-developers app
To flash those roms u mentioned, u need to unlock ur bootloader, n change the kernel provided within the roms.
Sent from my Nokia 3310 using Tapatalk 2
gouthamthemostwanted said:
Did you unlock your bootloader? If you haven't unlocked your bootloader none of the above mentioned Roms will work with you. (after unlocking the bootloader you need to flash a custom kernel according to the Rom you are flashing, via fastboot).
Press thanks if I helped you
Sent from my ST15i using xda app-developers app
Click to expand...
Click to collapse
thanks for the reply, and yes bootloader is unlocked (using the test point method), and I flash custom kernels (extracted from the installation zip boot.img of the ROMs I mentioned) before I go to CWM to install the ROM
dhruvraj said:
thanks for the reply, and yes bootloader is unlocked (using the test point method), and I flash custom kernels (extracted from the installation zip boot.img of the ROMs I mentioned) before I go to CWM to install the ROM
Click to expand...
Click to collapse
Does any custom boot.img work with your stock Rom? Try flashing ragekernel for gb in your stock Sony Rom. And see if your phone is working normal.
Sent from my ST15i using xda app-developers app
gouthamthemostwanted said:
Does any custom boot.img work with your stock Rom? Try flashing ragekernel for gb in your stock Sony Rom. And see if your phone is working normal.
Sent from my ST15i using xda app-developers app
Click to expand...
Click to collapse
thanks, just installed ragekernel v3.0 for Mini - the device boots up normal, into the stock ROM
What is says in the kernel version from the settings>about?
Sent from my ST15i using xda app-developers app
gouthamthemostwanted said:
What is says in the kernel version from the settings>about?
Sent from my ST15i using xda app-developers app
Click to expand...
Click to collapse
2.6.32.9-perf [email protected] #30
now i dont know what it said before I installed this kernel though
dhruvraj said:
2.6.32.9-perf [email protected] #30
now i dont know what it said before I installed this kernel though
Click to expand...
Click to collapse
Okay your bootloader is unlocked for sure. now let's get to the rom part. Download any custom Rom for st15i based on stock Sony Rom. Try to flash it in CWM recovery. And if it throws any errors then please reply with each and every letter it says in error in the recovery while flashing . ONLY FLASH A gingerbread Rom based on stock Rom! Eg: clean and tweaked Rom from serjar FOR GINGERBREAD.
Sent from my ST15i using xda app-developers app
dhruvraj said:
Folks, someone please help me out.
desperate situation here.
Xperia mini 15sti : rooted, unlocked bootloader, busyboxed, RecoveryX installed (version for 2.3.4) - firmware 4.0.42 version : gingerbread
None of the ROMs I've downloaded have worked so far. Everything results in an error or another. It is incredible how difficult I'm finding this to be.
CM10 : gives me assert errors. Saying its not smultron. I've removed the assert check in updater, then it starts giving me installation aborted after some time.
CM9 : same assert error
ParanoidAndroid : symlink errors during installation
AOKP : installation fails with set path something
I've spent countless hours on finding out the root cause of my problem - but given that everything fails, I am guessing there is something elementary that is missing (or wrong in my approach)
I'm on android gingerbread, and trying to jump to either JB or ICS nothing really works here (I follow the usual wipe data cache everything with every single install attempt so far. And then start with rooting flashing firmware back to 4.0.42, then recoverX, then new ROM etc)
please help
Dhruv
Click to expand...
Click to collapse
It seens that you formatted system before glashing cm and aokp,reflash stock and flash cm again reboot and enjoy or just open the zip go in meta inf folder find updater script,open it with notepad and remove the first six lines then close,repack again and flash
Sent from my SK17i using xda app-developers app
KhemaraS. said:
It seens that you formatted system before glashing cm and aokp,reflash stock and flash cm again reboot and enjoy or just open the zip go in meta inf folder find updater script,open it with notepad and remove the first six lines then close,repack again and flash
Sent from my SK17i using xda app-developers app
Click to expand...
Click to collapse
Yes but he also said after removing assert check in updater-script also it shows some errors it must be probably status 7 errors because of windows style end of line conversion corrupted the updater-script .
Sent from my ST15i using xda app-developers app
---------- Post added at 10:41 PM ---------- Previous post was at 10:16 PM ----------
Okay, let me tell step by step tell what should be done.
1. Flash rage kernel for gb (3.0)(fixed)
2. Download any stock based gb Rom for your device . For example , clean and tweaked gingerbread Rom by serjar. Place the rom zip in the root of your sd card.
3.Reboot into CWM recovery (included in rage kernel no need to flash CWM separately)
4. Do factory wipe from CWM.
5. Flash the Rom zip from CWM . In the example case it is clean and tweaked gingerbread Rom from serjar .
If flashing throws any errors then post the error here.
Sent from my ST15i using xda app-developers app
gouthamthemostwanted said:
Yes but he also said after removing assert check in updater-script also it shows some errors it must be probably status 7 errors because of windows style end of line conversion corrupted the updater-script .
Sent from my ST15i using xda app-developers app
---------- Post added at 10:41 PM ---------- Previous post was at 10:16 PM ----------
Okay, let me tell step by step tell what should be done.
1. Flash rage kernel for gb (3.0)(fixed)
2. Download any stock based gb Rom for your device . For example , clean and tweaked gingerbread Rom by serjar. Place the rom zip in the root of your sd card.
3.Reboot into CWM recovery (included in rage kernel no need to flash CWM separately)
4. Do factory wipe from CWM.
5. Flash the Rom zip from CWM . In the example case it is clean and tweaked gingerbread Rom from serjar .
If flashing throws any errors then post the error here.
Sent from my ST15i using xda app-developers app
Click to expand...
Click to collapse
I'll try putting gingerbread ROM ..but just to let you guys know I used notepad++ to avoid windows line end errors as per the posts around here. That stopped the assert failure but gave installation aborted after with no other error message. Now will put GB n tell you guys
dhruvraj said:
I'll try putting gingerbread ROM ..but just to let you guys know I used notepad++ to avoid windows line end errors as per the posts around here. That stopped the assert failure but gave installation aborted after with no other error message. Now will put GB n tell you guys
Click to expand...
Click to collapse
Just to confirm,
You used notepad ++ but did you change the eol conversion to Unix format before saving the file?
Sent from my ST15i using xda app-developers app
gouthamthemostwanted said:
Just to confirm,
You used notepad ++ but did you change the eol conversion to Unix format before saving the file?
Sent from my ST15i using xda app-developers app
Click to expand...
Click to collapse
No I think notepad++ does that by default. What you need to see is that it didnt give any assert error, tried to install for a while .. and then gave the error : installation aborted
Secondly, I'm getting errors in every single ROM out here. Now trying the GB rom .. will post the results, and thanks for assisting so far mate
Dhruv
dhruvraj said:
No I think notepad++ does that by default. What you need to see is that it didnt give any assert error, tried to install for a while .. and then gave the error : installation aborted
Secondly, I'm getting errors in every single ROM out here. Now trying the GB rom .. will post the results, and thanks for assisting so far mate
Dhruv
Click to expand...
Click to collapse
Update! Cyanogenmod 7.2 installed OK. So gingerbread is installing
Is it because of RecoverX then? Because while installing RecoverX it asks which version of xperia mini do you want - and I use android 2.3.4 - could it be the recovery not letting JB or ICS install then? Its 5.0.2.8 or something the one that I have
Pl let me know what to do next. cheers
Notepad doesn't change eol to Unix by default. After installing a prerooted kernel you don't have to use recovery x . after all that's the point in a preroot kernel! It comes with root and CWM recovery in built! Now what? Start flashing Roms, kernels and start exploring the infinite possibilities of android! :thumbup:
and hit the thanks button, it's more appreciated than typing thanks
Sent from my ST15i using xda app-developers app
dhruvraj said:
Update! Cyanogenmod 7.2 installed OK. So gingerbread is installing
Is it because of RecoverX then? Because while installing RecoverX it asks which version of xperia mini do you want - and I use android 2.3.4 - could it be the recovery not letting JB or ICS install then? Its 5.0.2.8 or something the one that I have
Pl let me know what to do next. cheers
Click to expand...
Click to collapse
For ICS or JB you don't need recoverx, if you use a custom kernel you can just flash the kernel and it has cwm inbuilt.
1. Just push the FXP cm10 zip for your device to sd card, flash the boot.img,
2. boot in cwm,
3. backup,
4. wipe data/factory reset,
5. install zip from sd card,
6. (if you want install the google apps=gapps) :good:
Problem was with CWM ... once I installed a GB custom ROM, the recovery was flashed to 6.0 something automatically
Every single ROM I tried to install after has worked flawlessly.
I have an xperia Mini, and it just doesnt work though, so I'm opening another thread on the overheating issue (which doesnt get solved no matter what you do)
thanks
Hi to all
I have a sony lww wt19i android 2.3.4 build no. .58 rooted & unlocked boot loader.
I want to install custom rom & kernel but I don't know nothing about how to install custom rom & kernel.
Plz tell I have to install rom first or flash kernel first after that install rom. Plz clear me this.
And plz tell me can I install custom ICS rom& kernel to my phone I mean I have GB right now.
And pz suggest me some gud stable fast ICS rom & compatible kernel.
Note:- Line in bold format is most important.
So plz frnds tell me what to do first.
thx to all frnds...
wrong section !!
Post in right section to be able to help you -reported-
Sent from my Xperia Mini using xda app-developers app
---------- Post added at 12:21 PM ---------- Previous post was at 12:00 PM ----------
jiturawat said:
Hi to all
I have a sony lww wt19i android 2.3.4 build no. .58 rooted & unlocked boot loader.
I want to install custom rom & kernel but I don't know nothing about how to install custom rom & kernel.
Plz tell I have to install rom first or flash kernel first after that install rom. Plz clear me this.
And plz tell me can I install custom ICS rom& kernel to my phone I mean I have GB right now.
And pz suggest me some gud stable fast ICS rom & compatible kernel.
Note:- Line in bold format is most important.
So plz frnds tell me what to do first.
thx to all frnds...
Click to expand...
Click to collapse
since you unlocked your BL, you know how to use fastboot commands and ADB
download custom rom and kernel
you can use pureness rom, Ultimate HD or any ics rom you like.
And for custom kernel there is MeSa, and lupus.. etc choose what you like
flash kernel via fastboot commands
1-shutdown your phone
2-Hold on volume up and connect usb from phone to pc
now you can see LED notification shines in blue
3-open cmd and navigate to fastboot folder
4- write:
fastboot devices
fastboot flash boot directorytokernel boot.img
replace with actual directory
5- wait until in finish
6-move rom to your SD card
7-enter recovery twrp or cwm
8-flash rom
HERE is a collection of roms, kernels...+++ etc
after I installed rom my xperia mini won't open anymore. I couldn't remove battery because of it's not removable!!!
I couldn't get in recovery menu just sony ericsson menu , please uregently need help!
phone was rooted and unlocked bootloader too, I back uped prior rom but it couldn't load the minicm10 version then
I tried minicm7 version and installed googleapps for cm10 too, it was all ok but after rebooting it has been frozen,
please help!!!
wht recovery menu not show up anymore????
what can I do?
hey bro, answer the following
what rom,kernel did u flash sorry for question???
Sent from my E10i using xda app-developers app
---------- Post added at 02:26 AM ---------- Previous post was at 02:24 AM ----------
i think ur phone is bricked, cant open right??? just use seus to unbrick your phone
Sent from my E10i using xda app-developers app
now everythings gone!!.!!!!!!!!!!!!
after I install flashtool 0.9.10 new version, I tried flash with its kernel due to no one helped me , after flash tool said flashing finished please unplug and start your phone, now phone light doesn't show up and phone doesn't open at all anymore,
can anyone please help me, how could I turn this phone on ??????
rom was MiniCM10-4.0.1-robyn but after it failed I stupidly tried MiniCM7-2.2.1-robyn and it's installed. and after that I instsalled gapps-jb-20120923-signed and reboot.
kernel was the E10_nAa-02_2.6.29-nAa-02 before the rom installing process.
tommikks said:
rom was MiniCM10-4.0.1-robyn but after it failed I stupidly tried MiniCM7-2.2.1-robyn and it's installed. and after that I instsalled gapps-jb-20120923-signed and reboot.
kernel was the E10_nAa-02_2.6.29-nAa-02 before the rom installing process.
Click to expand...
Click to collapse
You SHOULD have updated the kernel according the instructions in the ROM-threads, which you failed to do. Now I guess you've flashed the x10blrelock.ftf? In that case, your phone needs a JTAG.
yes you right it was x10blrelock.
xperia x10 mini is not turning on
SmG67 said:
You SHOULD have updated the kernel according the instructions in the ROM-threads, which you failed to do. Now I guess you've flashed the x10blrelock.ftf? In that case, your phone needs a JTAG.
Click to expand...
Click to collapse
i have same prob my xperia x10 mini is not turning on after flashing x10blrelock.ftf kernel and by the way what is jtag
Flashing of x10blrelock.ftf happens too often now.
DEVs: please put a warning in all your install-instructions, when you mention to unlock bootloader, never to flash x10blrelock.ftf
hafizullah_dude said:
i have same prob my xperia x10 mini is not turning on after flashing x10blrelock.ftf kernel and by the way what is jtag
Click to expand...
Click to collapse
Phone-repair shops have a JTAG-box that can restore the original firmware using special connections inside your phone. You'll have to pay for it to get your phone working again.