Related
I root xperia x10 and I installed xrecovery,today I tried to run this rom FeraLab*** v14.2 ~Volt and after that is stuck on boot,i can not run download mode too.
please what to doo?
Are you unlocked bootloader and flash kernel
no,i made a mistake. i think that something is going on with update service.mybe will repair a phone .
yeeeeeeaa it is working again
You can flash the offical room to slove this problem but you need remember the room you flash should suitable for your baseband and you can search it in here.I want to send it to you but now I need sleeping hehe .Good Luck
---------- Post added at 11:32 PM ---------- Previous post was at 11:31 PM ----------
Congratulation hehe
android version is 2.3.3
baseband 2.1.71
kernel 2.6.29-00054
and i unlocked bootloader with flash tool
what to do
crosmurf said:
android version is 2.3.3
baseband 2.1.71
kernel 2.6.29-00054
and i unlocked bootloader with flash tool
what to do
Click to expand...
Click to collapse
What u looking to do exactly pal?
Sent from my X10S using XDA
I want to put rom file in the phone and I almost destroy it.
U need to download the Rom of choice to your pc. Then u need to copy it somewhere onto your sd card that is easily located (personally I have go oder on my sd called roms so I put them there). Then u must boot into recovery and install the zip from where u placed it on sd card. If u not sure bout anything I said let us know I'll explain in more detail if u need
Sent from my X10S using XDA
I made it all but it will not work properly,I think the problem is with kernels.After boot stays frozen.I change the rom to update.zip and then i use xrecovery.
U don't need to change to update.zip just select install custom zip then go to sd card and find it
Sent from my X10S using XDA
do i need to change a kernel?You say that I only need to copy any rom on the SD card.means that i only need to find with xrecovery at custom zip that rom and that is it.Now I will try again
Flash global generic firmware pal and start again I'd say
Sent from my X10S using XDA
which sw to use
Tell you how to install v14.2 in right way
Hi friend . If you want to use V14.2 Rom follow those. In all the steps before you need make sure your x10 is unlocked bl (important) .First you need flash kernel suitable for V14.2 (u can find it in where you download Rom ,The recover have been merged into kernel .I think you can't open xrecover now because you install it in the Rom ,you can't open xrecover in a new rom without it .if you flash kernel bring xrecover ,that means you can use it in any rom hehe) Then open cwm recover install V14.2 Rom in you sdcard (I think it still in you sdcard if you didn't delete it ) Tha's all .Now you can use V14.2 .Enjoy
If I were you Id use pcc/seus and go back to stock.Then look at Crowds guide,follow it and unlock bl.
I run Feras v14.2 and everything works fine
Posted using s2 by xda premium
stuck on boot tried flashing it a few times but does not want to work can someone help???
Rubz21 said:
stuck on boot tried flashing it a few times but does not want to work can someone help???
Click to expand...
Click to collapse
Flashed what?
Sent from my GT-I9300 using XDA
hey guys please some help
i wanted to install a custom rom
now im stuck
i did this
rooted via flastool
cwm5 via flash tool
i have 2.1 at the moment
after that to install the rom i was advice to install the kernel v6
i did
after that i install the recovery v6 for gb
i did
booted in recovery and installed the rom
myfirstrom.zip
and now im stuck
what can i do to fix this
thanks
Wrong thread buddy
Sent from my X10i using xda premium
elmanortega said:
hey guys please some help
i wanted to install a custom rom
now im stuck
i did this
rooted via flastool
cwm5 via flash tool
i have 2.1 at the moment
after that to install the rom i was advice to install the kernel v6
i did
after that i install the recovery v6 for gb
i did
booted in recovery and installed the rom
myfirstrom.zip
and now im stuck
what can i do to fix this
thanks
Click to expand...
Click to collapse
This tread should be in Q&A not in DEV.
Anyway do U have bootloader unlocked?
That rom is a 2.3 rom and you need to have and unlocked bootloader. You need to have 2.3 on your device first which would you would find in my signature below. So skip through the tread and find 2.3 Download it and flash it and try the rom again.
Sent from my X10i
Dude u r in 2.1 now. It has a baseband of .49 or .54. GB needs a baseband of .71. So the only option is first u download a pre-rooted firmware image and flash it via flashtool. U will boot into GB. Then unlock bootloader using Laser's method and install custom kernel like DoomKernel.
Follow this method
[RECOVERY image] {v2} X10 GB 3.0.1.G.0.75 [Prerooted + Fixed xRecovery] to insatll the prerooted firmware using flashtool.
Unlock bootloader using this steps from
[HOW-TO]UNLOCK bootloader for X10
Then flash DoomKernel from this link
[KERNEL][X10] DooMKernel [UNLOCKED BOOTLOADERS]{Rel:v06}[Dt:10/Jan][FW3.0.1.G.0.75] and boot up into stock rom or the previous GB rom u r using.
For Stock based roms, DoomKernel is simply the best.
For CM7 based roms, use FXP 130 kernel provided here FXP 130 and
For CM9 based roms, use FXP 132 kernel for better performance which u can download in FXP CM9 Thread.
---------- Post added at 11:10 AM ---------- Previous post was at 11:08 AM ----------
kingstonxl said:
This tread should be in Q&A not in DEV.
Anyway do U have bootloader unlocked?
Click to expand...
Click to collapse
He hasnt even updated to GB.. Still in stock 2.1.
Don't scare the guy with laser's method for now he is starting out small like we at one time were(im still growing) , the latest version of flashtools could do it easy. Its all in my signature if you tries it.
Sent from my X10i
brenty108 said:
Don't scare the guy with laser's method for now he is starting out small like we at one time were(im still growing) , the latest version of flashtools could do it easy. Its all in my signature if you tries it.
Sent from my X10i
Click to expand...
Click to collapse
Sry i didn kw ur post.. Let him do the way he think is best
thanks guys
im downloading the 2.1 ans 2.3 roms
now how do i install them?
i can access xrecovery
but when i connect to flashtool i dont have all the options
actually none
the devices is detected but thats it
can a stock rom be install using xrecovery?
elmanortega said:
thanks guys
im downloading the 2.1 ans 2.3 roms
now how do i install them?
i can access xrecovery
but when i connect to flashtool i dont have all the options
actually none
the devices is detected but thats it
can a stock rom be install using xrecovery?
Click to expand...
Click to collapse
dude flashing option works only when u r in download mode. i think u have 2.3.4. and stock kernel. if u want custom roms u have to unlock bootloader shown u n the post i provided
a2441918 said:
dude flashing option works only when u r in download mode. i think u have 2.3.4. and stock kernel. if u want custom roms u have to unlock bootloader shown u n the post i provided
Click to expand...
Click to collapse
thanks
Originally Posted by Androxyde
X10i Generic
Generic version 2.3.3 build 3.0.1.G.0.75 (MD5: 36F52BAA3556CDD7E56383614C01E5D6)
this one is no longer available
Thread Moved
You should Know better, your post count indicates you have been active, so should be fully aware of the rules
after i connect in flash mode
it stays for a few secs and reboots into the sse screen
is there a way to install the oem rom
in xrecovery?
or a 2.1 rom in recovery?
if i install a 2.1 custom rom
will that help??
im connected to flashtool in flash mode but nothing no options
what do i do now?
ok i finally go it to
where it was suppose to be to install formware
and this is where i am
Did you click fastboot? Click flashmode as x10 doesn't fastboot lol
Sent from my Xperia X10 using xda premium
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
If that rom is in ftf format
Open with 7zip or winrar
Look for kernel.sin
And place it in a folder
In flashtool create kernel
Point it to the folder containing kernel.sin
You should then be able to place your created kernel into firmware folder and flash it
I haven't had much experience with those roms so it's just a suggestion
Sent from my Xperia X10 using xda premium
elmanortega said:
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
Click to expand...
Click to collapse
You need to install a kernel called fxp132 from team fxp for ICS ROM to work... see my other posts in Q&A.. I have uploaded it somewhere.. you should be able to access through my profile->-> posts.
Sent from my Transformer TF101 using xda app-developers app
elmanortega said:
thanks im good now
im about to install the ics rom
from
{rom}{6mp WORKING }XPERIA S ICS - CM9{14/8/12} {rom}
but i dont know wich kernel to install
i will write here what i did
so other can have an easy install
thanks to brenty108 for the help
Click to expand...
Click to collapse
hey friend, you have downloaded the xperia s ics by vassishta but you dont know what kernel to be used?, dont be so lazy reading all the stuff in that thread (i mean xperia s ics), fxp 132 kernel is included there and instructions on how to flash the rom, hope i helped you, please press thanks button for me, pressing it is just an easy thing.. cheers.. :good:
i have xperia sola android version 2.3.7 , kernal version 2.6.35.7+ and build number 6.0.B.1.564 i was trying to install PURE BLOOD ROM v1.0 - The Ultimate Stock Xperience(ics)
and according to tutorial
i installed rom via CMW v5
but when i restarted the phone
it stuck on the sony logo and keep restarting
i restored the earlier ROM which i backup-ed.
i Want to install that stocked based custom rom how to install please clarify me
i tried many times but unable to install that rom...
That rom is based on ics not gb my friend
First flash ics. Then use that rom
drsanket_xperia_u said:
That rom is based on ics not gb my friend
First flash ics. Then use that rom
Click to expand...
Click to collapse
you mean first i have to flash with official stock rom or what??Plz tell me..
You need the ICS stock rom first to get the kernel.
Look for the global ICS file in the forums. It's on a torrent.
nishangrg said:
you mean first i have to flash with official stock rom or what??Plz tell me..
Click to expand...
Click to collapse
Yes u should read that rom is based on 6.1 not 6.0 (gb)
So if u want that rom just flash 6.1.b.1.10 and then flash the pure blood rom as per instructions
After installing pureblood ROM via CWM,switch off the phone and then flash .54 Kernel through flashtool by putting in fastboot mode.No need for installing stock ics.I can provide you the kernel file,if you need.
waht is best between Ultimate sola and pure blood?
ultimate saola is v1, it's mean that pure blood v2 is most recent?
akp.ajinkya said:
After installing pureblood ROM via CWM,switch off the phone and then flash .54 Kernel through flashtool by putting in fastboot mode.No need for installing stock ics.I can provide you the kernel file,if you need.
Click to expand...
Click to collapse
plz provide me the link i want to try..
drsanket_xperia_u said:
Yes u should read that rom is based on 6.1 not 6.0 (gb)
So if u want that rom just flash 6.1.b.1.10 and then flash the pure blood rom as per instructions
Click to expand...
Click to collapse
so you mean i should flash 1st ICS Stock Firmware which is in the extension .ftf through flashtool? right?
and Plz if i had to flash ICS stock Firmware.ftf file through flashtool then plz give me a tutorial to flash
i want to flash ICS on my xperia sola.. i want to upgrade my GB to ICS with Custom rom....
akp.ajinkya said:
After installing pureblood ROM via CWM,switch off the phone and then flash .54 Kernel through flashtool by putting in fastboot mode.No need for installing stock ics.I can provide you the kernel file,if you need.
Click to expand...
Click to collapse
They are different ROMs. One is stock lite (All bloat removed). The other is stock enhanced.
Check the thread to see which is which.
Snowstormzzz said:
They are different ROMs. One is stock lite (All bloat removed). The other is stock enhanced.
Check the thread to see which is which.
Click to expand...
Click to collapse
Yups,I know the difference,i have used both of them.Also pureblood s .54 based and ultimate sola is .10 based.
---------- Post added at 06:22 PM ---------- Previous post was at 06:17 PM ----------
nishangrg said:
plz provide me the link i want to try..
Click to expand...
Click to collapse
Here's the link:https://www.box.com/s/o6i2gh5hymxxgiohh8im
Hello
I am a newbie Android user though I flashed Real ICS r6 and Extended Stock kernel a few months back. The ROM is great, the kernel works fine. But I wanted to Overclock and use Swap File which isn't enabled in extended stock so, I wanted to install MESA which is compatible with Real ICS as well as my phone. But I have no idea how to flash a NEW kernel.
If I flash a new kernel does my ROM get erased too?
I need a detailed step by step tutorial about flashing MESA and replacing Extended Stock with it, without removing Real ICS r6. Any help is appreciated guys. Also, please take note that I cannot brick the phone as I won't get a new one for years if that happens.
Thank you in advance.
AW: [SE Live with Walkman] Installing MESA Kernel over Extended Stock Kernel
No it won't erase the ROM
See my "how to install a custom kernel/rom", there you can see how to flash the boot.img using flashtool
Sent from my Nexus 7 running Android 4.2.1
The steps is so easy,
1-Download the kernel, extcract if it is a zip file
2-Get boot.img
3-And put it in your fastboot folder
4-Open cmd and navigate to fastboot folder,
Or simply click on start search for cmd and drag it in fastboot folder then open it
5-shutdown your phone
6-hold on volume up and connect the usb from the phone to pc
7-it will ask you for drivers ( skip if you already done so)
8- in cmd run the following commands
Fastboot devices
Fastboot flash boot directorytoboot boot.img
Replace directorytoboot with actual directory
It will not earse your rom.
And btw xperia 2011 is hard to be bricked
Click thanks if I helped you
Sent from my Xperia Mini using xda app-developers app
Thank You
Thank you to the both of you, I have successfully flashed MESA 3.2 on my Live with Walkman. So far so good.
Try MESA Hybrid v3.6 kernel. It's better. Flash kernel via Fastboot and then flash mesa-hybrid-stock.zip via CWM.
only recovery and mesa kernel
live with walkman
i am only left with mesa kernel and its recovery..
i accidently wiped system while trying to install real ics ir6 yesterday..
now when i tried to flash ics r6 through recovery it i flashed but restarts and shuts down.
i read in a post that i need to have preinstalled stock rom in order to flash custom rom..
is this true??
if yes kindly help me, what should i do now,
can i fastboot flash the stock rom .ftf or whatever be the method please please some1 help me.
ballackcool said:
live with walkman
i am only left with mesa kernel and its recovery..
i accidently wiped system while trying to install real ics ir6 yesterday..
now when i tried to flash ics r6 through recovery it i flashed but restarts and shuts down.
i read in a post that i need to have preinstalled stock rom in order to flash custom rom..
is this true??
if yes kindly help me, what should i do now,
can i fastboot flash the stock rom .ftf or whatever be the method please please some1 help me.
Click to expand...
Click to collapse
Firstly flash stock ftf using flashtool in flashmode or just place any rom.in ur sdcard which can run in this situation for e.g. my rom xperia nexus and flash it
Press THANKS if I helped,
Best Regards,
AJ
alokbina said:
Firstly flash stock ftf using flashtool in flashmode or just place any rom.in ur sdcard which can run in this situation for e.g. my rom xperia nexus and flash it
Press THANKS if I helped,
Best Regards,
AJ
Click to expand...
Click to collapse
Thanx for the reply
i wanna tell u the exact situation
there is no os in my phone just mesa kernel and recovery,
yesterdayas u said i tried to flash .ftf stock but it showed me header error
so do i need to switch back to stock kernel first in order to flash stock rom ..
thanx inadvance..
ballackcool said:
Thanx for the reply
i wanna tell u the exact situation
there is no os in my phone just mesa kernel and recovery,
yesterdayas u said i tried to flash .ftf stock but it showed me header error
so do i need to switch back to stock kernel first in order to flash stock rom ..
thanx inadvance..
Click to expand...
Click to collapse
Nopes flashtool automatically flashes the stock kernel with it anyways did u try installing any other rom on the mesa kernel?
Press THANKS if I helped,
Best Regards,
AJ
hi. if you encounter header error ,
you must install (fastboot, ...)driver correctly
then go ahead.(its right)
Hi I want to install SlimCM Custom ICS Based rom to my new xperia U but not sure about the procedure [have read the guide but still confused] I've downloaded the rom and 2 kernels : ( vengence / SlidingXU ) but not sure which one will work with this rom.... Right now I'm on stock rom and kernel on android 2.3 gingerbread.... but I successfully unlocked my bootloader ... can someone step by step guide me as I don't have any roote access nor recovery installed right now in my phone...
Thanks in advance...
orangzeb said:
Hi I want to install SlimCM Custom ICS Based rom to my new xperia U but not sure about the procedure [have read the guide but still confused] I've downloaded the rom and 2 kernels : ( vengence / SlidingXU ) but not sure which one will work with this rom.... Right now I'm on stock rom and kernel on android 2.3 gingerbread.... but I successfully unlocked my bootloader ... can someone step by step guide me as I don't have any roote access nor recovery installed right now in my phone...
Thanks in advance...
Click to expand...
Click to collapse
i think you need to root your phone first,install cwm,then flash stock ICS ROM,after that then flash SlimCM rom.
what about kernel ?? do I need to install it in the end and what kernels work best with SlimCM ? won't I loose root when I flash stock ICS Rom ?
orangzeb said:
what about kernel ?? do I need to install it in the end and what kernels work best with SlimCM ? won't I loose root when I flash stock ICS Rom ?
Click to expand...
Click to collapse
erm...now you on GB right?
download stock ICS ftf,flash it,then root,install cwm
follow the instructions to install
http://forum.xda-developers.com/showthread.php?t=2143750
orangzeb said:
what about kernel ?? do I need to install it in the end and what kernels work best with SlimCM ? won't I loose root when I flash stock ICS Rom ?
Click to expand...
Click to collapse
Use fast boot and flash sliding xu kernel. Actually I recommend transcendence kernel. Flash that, reboot into recovery, copy ROM zip to storage. Wipe data, cache, dalvik and system and then flash slim cm zip
Sent from my Xperia U using xda app-developers app