Heeeeere we go.
long story short I messed up, here are the symptoms(spent 2 hours scouring the internet and XDA BTW)
SVF:108:1:2
Failed To Boot 3
Entering NvFlash Recovery Mode
thats after trying to enter recovery (vol-/pwr), alternatively I recieve a "Starting RSD mode" if I try to boot normally or try to plug phone in to charge.
Also, just tried (vol+/vol-/Pwr) received "Starting Fastboot Protocol support"
battery too low to flash...this presents a problem as I am unable to plug the phone in without it coming on....
All tutorials Ive found involve failed to flash 0x1000 or something of that nature, I am not receiving that message.
It never progresses past that. If anyone could point me in the direction of a good tutorial or even the thread that Im apparently missing it would be greatly appreciated.
Thanks!
Have you tried this thread?
[How To] Recover from a soft brick
giqbal said:
Have you tried this thread?
[How To] Recover from a soft brick
Click to expand...
Click to collapse
Thats the one I was referring to that flashed that lil red light. My atrix isnt displaying either of those problems and I cannot get to fast boot.
gorealmighty said:
Thats the one I was referring to that flashed that lil red light. My atrix isnt displaying either of those problems and I cannot get to fast boot.
Click to expand...
Click to collapse
Can you get to your recovery? If you can get to rsd you might be able to recover by flashing sbf
giqbal said:
Can you get to your recovery? If you can get to rsd you might be able to recover by flashing sbf
Click to expand...
Click to collapse
Unfortunately the process as I described it above is how it happens. I dont get to choose which "mode" it goes to. It just depends on the action/button combination. It never progresses past that.
gorealmighty said:
Unfortunately the process as I described it above is how it happens. I dont get to choose which "mode" it goes to. It just depends on the action/button combination. It never progresses past that.
Click to expand...
Click to collapse
Well i think you need to flash sbf file in rsd mode. The sbf should be on the version you had originally or higher (if you were on 2.3.4 so don't flash 2.2.2 otherwise you'll hard brick). I might be wrong so someone else should confirm me before you proceed with it.
Not to sound like a broken record...but I'm not sure that that's possible. I don't have the option to choose. Unless you ate suggesting that from the available options I listed above I make an attempt.
Sent from my Inspire 4G using XDA
gorealmighty said:
Heeeeere we go.
long story short I messed up, here are the symptoms(spent 2 hours scouring the internet and XDA BTW)
SVF:108:1:2
Failed To Boot 3
Entering NvFlash Recovery Mode
thats after trying to enter recovery (vol-/pwr), alternatively I recieve a "Starting RSD mode" if I try to boot normally or try to plug phone in to charge.
Also, just tried (vol+/vol-/Pwr) received "Starting Fastboot Protocol support"
battery too low to flash...this presents a problem as I am unable to plug the phone in without it coming on....
All tutorials Ive found involve failed to flash 0x1000 or something of that nature, I am not receiving that message.
It never progresses past that. If anyone could point me in the direction of a good tutorial or even the thread that Im apparently missing it would be greatly appreciated.
Thanks!
Click to expand...
Click to collapse
You say in this post that when you boot normally the phone says "Starting RSD Mode". Im talking about using this mode to flash sbf…you can search the forums on how to flash sbf in RSD mode.
Also you'll need to charge your battery some way(battery can't charge without going into OS) before you flash.
gorealmighty said:
Not to sound like a broken record...but I'm not sure that that's possible. I don't have the option to choose. Unless you ate suggesting that from the available options I listed above I make an attempt.
Sent from my Inspire 4G using XDA
Click to expand...
Click to collapse
I'll give it a try, thanks
Sent from my Inspire 4G using XDA
FAIL any more suggestions?
Sent from my Inspire 4G using XDA
umm...
thats after trying to enter recovery (vol-/pwr), alternatively I recieve a "Starting RSD mode" if I try to boot normally or try to plug phone in to charge.
Also, just tried (vol+/vol-/Pwr) received "Starting Fastboot Protocol support"
battery too low to flash...this presents a problem as I am unable to plug the phone in without it coming on....
Click to expand...
Click to collapse
if you can get to working fastboot support you can probably recover.
http://forum.xda-developers.com/showthread.php?t=1501532
follow Alaq/ Uncle Cemka's method of flashing pudding via fast boot, I have recovered more than one phone this way, your going to need a way to charge your battery though, might have to buy an external battery charger, build a powered usb cable or cutup a cable and apply the + and - straight to your battery....you can search and find ways to charge your battery.
Also a little more info than just "Fail" would be helpful, did the RSD flash fail, is the phone just boot looping and going straight to RSD support or fastboot support? Error messages? it may not seem relevant but many of us have seen similar error messages and know different ways to get back to a working phone but we need more information from you to be able to help.
Also I have seen phones with the SVF:105.1:2 failed to boot error actually be accessible by RSD even when the screen did not mention RSD support was up...
You might need to strip the end of a USB cable and charge the battery directly. Another user posted instructions somewhere. I'm sure a quick google will reveal all.
Sent from my MB860 using Tapatalk 2
Wreaks, thanks much I'll look into it.
Consolation thank you as well.
I'm not giving up I'm still working on the beast.
Sent from my Inspire 4G using XDA
Related
Motorola Atrix 4G At&t show error"SVF:105.1:2 Failed to boot 0X1000"
whn i try to downgrade to v2.3 to v2.2.2 after flashing show this message
how can i solve it pls any 1 give me the solution
post it here
There is no fix. You are hard-bricked.
Sent from my MB860 using XDA App
Pull the battery and try:
Press and hold vol down while you turn on your phone until "fastboot" tag show up in your screen the release vol down and press vol up once to enter to fastboot
Check if it work?
bivrat said:
Motorola Atrix 4G At&t show error"SVF:105.1:2 Failed to boot 0X1000"
whn i try to downgrade to v2.3.4 to v2.2.2 after flashing show this message
how can i solve it pls any 1 give me the solution
post it here
Click to expand...
Click to collapse
Sent from my MB860 using XDA App
thr is no option like this............
just show this error and shut off the phone.............
SVF:105.1:2 Failed to boot 0X1000
any other solution...............'
How it happened? After flashing a SBF by RSD? Did you were bootloader unlocked before?
Sent from my MB860 using XDA App
There is no fix. You are hard Bricked.
Insurance will cover, AT&T store MIGHT if you say it happened when installing gingerbread update I guess.
The reason I was asking was due to the2dcour stated:
the2dcour said:
yes but you will get 0x1000 error. Don't freak out, it will let you boot in to fasboot and unlock. In fact, if you boot directly into fastboot after flash you wont even seen the 0x1000 probably. This has worked for multiple people that flashed 2.3.4 official sbf or official OTA 2.3.4 . As always, not guaranteeing anything for your specific phone.
Click to expand...
Click to collapse
BUT THAT APPLIED FOR A SPECIFIC PROCEDURE AFTER FLASHING BY RSD 2.3.4 WITH PUDDING SBF
IF YOU FLASHED A MOTO SBF WITHOUT PUDDING AFTER BEEN "UNLOCKED" SO THEN YES IS A HARD BRICK
Sent from my MB860 using XDA App
mramirezusa said:
The reason I was asking was due to the2dcour stated:
BUT THAT APPLIED FOR A SPECIFIC PROCEDURE AFTER FLASHING BY RSD 2.3.4 WITH PUDDING SBF
IF YOU FLASHED A MOTO SBF WITHOUT PUDDING AFTER BEEN "UNLOCKED" SO THEN YES IS A HARD BRICK
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Well, there are enough warnings which say not to downgrade from 2.3.4. Except the SBF with Pudding. And if you ignore those warnings, that's what you get.
Sorry dude, it is your own fault. Phone is bricked....
whn i try to flashing .sbf using rsd mode thn it happen to me.............. so how can i solved by own............... i dnt unlocked it by bootloader
so thr no solution to recover my phone.............
bivrat said:
whn i try to flashing .sbf using rsd mode thn it happen to me.............. so how can i solved by own............... i dnt unlocked it by bootloader
so thr no solution to recover my phone.............
Click to expand...
Click to collapse
Nope. No fix. Sorry
so now wht can i do............ can i claim to motorola warranty...... they can solved it............. or no 1 can solved it...........
The warranty "should' cover it.
But like everyone already said there are multiple warnings not to downgrade once using the official 2.3.4 update for this very reason. If I recall correctly it even said so in the text message I received that informed me of the update.
My Atrix has the same situation, someone find a solution?
There is no solution for a hard brick.
Sent from my MB860 using XDA App
pls chk this link hope ur prob will solved http://forum.xda-developers.com/showthread.php?t=1182871
motorola atrix mb860 now a paper waight
phone was already rooted using gingerbreak. attempted update through settings and it would download but fail to install.
i had install cwm, everything was fine.
but think i tried a update file, that gave me the failed to boot 2 with motorola logo.
well was spending endless time on forums trying to understand what, mistake i did.
and tried the rsd lite and using preinstall rsd lite file. then got the failed to boot 0x1000 no os detected. with 14 options, and nothing seem to work.
no file would work. batter wont charge even tryed to hard charge cutting charger and going strait to battery ...
IF ANYONE KNOWS A FIX.. please inform me.
I didnt have this much a hard time with my htc vivid ...
IF THERE IS NO FIX , I WILL HAVE FUN SMASHING THE THING ..
anyways .
thankx for your time, hope to hear something good..
celticpayne said:
phone was already rooted using gingerbreak. attempted update through settings and it would download but fail to install.
i had install cwm, everything was fine.
but think i tried a update file, that gave me the failed to boot 2 with motorola logo.
well was spending endless time on forums trying to understand what, mistake i did.
and tried the rsd lite and using preinstall rsd lite file. then got the failed to boot 0x1000 no os detected. with 14 options, and nothing seem to work.
no file would work. batter wont charge even tryed to hard charge cutting charger and going strait to battery ...
IF ANYONE KNOWS A FIX.. please inform me.
I didnt have this much a hard time with my htc vivid ...
IF THERE IS NO FIX , I WILL HAVE FUN SMASHING THE THING ..
anyways .
thankx for your time, hope to hear something good..
Click to expand...
Click to collapse
You have a soft brick and can recover. I don't have time to find the links for you right now, but search for soft brick solutions.
You have a very common error with a common solution.
http://youtu.be/QiZdY9rw-uo
celticpayne said:
phone was already rooted using gingerbreak. attempted update through settings and it would download but fail to install.
i had install cwm, everything was fine.
but think i tried a update file, that gave me the failed to boot 2 with motorola logo.
well was spending endless time on forums trying to understand what, mistake i did.
and tried the rsd lite and using preinstall rsd lite file. then got the failed to boot 0x1000 no os detected. with 14 options, and nothing seem to work.
no file would work. batter wont charge even tryed to hard charge cutting charger and going strait to battery ...
IF ANYONE KNOWS A FIX.. please inform me.
I didnt have this much a hard time with my htc vivid ...
IF THERE IS NO FIX , I WILL HAVE FUN SMASHING THE THING ..
anyways .
thankx for your time, hope to hear something good..
Click to expand...
Click to collapse
Where you in the process of unlocking your bootloader?
how unbrick the hard bricked Atrix 4g. (svf 105:1:2 failed to boot 0x1000 entering nv
bivrat said:
Motorola Atrix 4G At&t show error"SVF:105.1:2 Failed to boot 0X1000"
whn i try to downgrade to v2.3 to v2.2.2 after flashing show this message
how can i solve it pls any 1 give me the solution
post it here
Click to expand...
Click to collapse
I got security boot key for my atrix 4g and used nvflash to encrypt it and now i got my hard bricked atrix back as it was before hard bricking. Process is too easy but nobody knows here on this site. if anyone want to unbrick the hard bricked atrix 4g then please contact me on. Cheers Motorola AT&T
Soooo ....I tried to install the update from OTA and my phone is now stuck in a failed to boot mode /starting rsd services screen......anyone help me out real quick? This is my first MOTO since the star tac , ive been strictly htc since the mogul....im rooted other than that ive done nothing else to the phone.....
If it is "Starting RSD Services" then your phone is not bricked. Assuming you can't make it boot any other way, you can load up RSD Lite on your pc, connect the phone via usb, and flash the latest SBF which will completely reload your OS. Granted you are going to need the correct drivers to do this.
Now, I'm wondering if you've done anything to this phone prior to applying the OTA update or was the phone completely stock? If it was stock and you did not unlock the bootloader then I'd just return it to Sprint and let them take responsibility for it. Otherwise you can do the repair yourself but only at your own risk...
I've posted the basics below but feel free to click here to go to the actual thread which explains this. I recommend you make sure your phone is charged before doing this.:
RSD Lite and 32 Bit Drivers (Install the 32bit drivers if you are running a 32bit Windows OS)
64 Bit Drivers (use these instead are running a 64 bit version of Windows.)
Latest SBF
1. DL and install RSDLite and Driver package from link above
2. Power down your phone
3. On your phone hold vol up and power till you see RSD at the top of the screen
4. Launch RSDLite from your program menu on your pc/laptop
5. Press the “. . .” button next to the box labeled “Filename”
6. Load up the SBF file you extracted from the MR download
7. Plug your device into your computer RSDLite should recognize your phone right away if you installed the drivers from this link i provided
8. Press the “Start” button
9. Be patient...takes a while...will reboot a couple times so grab a beverage of choice...use the restroom...take out the dogs...whatever...
10. may require activation again...mine did so be sure you have a means in which to do so...web...phone to call sprint for programming...OTA...
11. Enjoy and hit thanks!!!
Don't thank me, thank Yay 4 Juggs, I took this from his thread. If you have further issues you should post them there.
yeahried to flash the newest update, but now all it says is failed to boot 2 at the top of the moto screen...... Idk what now...???
make sure you have insurance
why would i need insurance? this phone is less than a month old, and the thing dumped on me while flashing Sprints OTA system update.....pretty sure it is thier fault.......lol......
The sbf update failed? Pull the battery for a few minutes then put it back and press and hold volume down while holding the power button. Does it say fastboot?
Also, you are within your return period so they will probably take it back unless you unlocked the bootloader. I don't think they'll take it back if it says unlocked at the top when you boot it, if it doesnt say that it should be fine because Sprint is okay with rooting. I wouldn't tell them you attempted the SBF though, just that the OTA update borked your phone.
ok I got it thanks everyone.......rsd failed to flash because my battery was lower than 50% .......i charged it and it flashed the first time with no problems......i dont understand why you have to re register your phone after the rsd flash though.....Motorola Android phones are wierd
I'm glad to hear your phone survived. Yeah you definitely want to make sure your phone is charged whenever you do any sort of modifications to the system/bootloader/recovery partitions. As for the reactivation, its not bad once you learn your MSL number you can do it yourself without needing to call Sprint. I'm thankful your phone didn't brick. lol
My phone also was recovered after doing as outlined by Yayy . Don't go into RSD with a low battery or you WILL pay the consequences.
I tried doing this and my battery died... Now I'm not sure where to go from here. I either charge it from the computer and ONLY the green led lights up and then like 10 minutes later the phone automatically comes on and says failed to boot 2, starting rsd, battery too low to flash. Or I can plug it into my wall and the phone automatically comes on and says the same thing immediately. Which way should I do this?
Nickdroid86 said:
I tried doing this and my battery died... Now I'm not sure where to go from here. I either charge it from the computer and ONLY the green led lights up and then like 10 minutes later the phone automatically comes on and says failed to boot 2, starting rsd, battery too low to flash. Or I can plug it into my wall and the phone automatically comes on and says the same thing immediately. Which way should I do this?
Click to expand...
Click to collapse
You may want to look on ebay for a Motorola Photon 4G / Droid 3 Battery Charger for a few bucks/no shipping cost. Order the charger, rush shipping if you feel you need to, open the package, take the battery out of your phone, plug the battery in the wall with the charger, and wait until the light changes from red to blue/green and continue from there.
Sent from my MB855 using xda premium
deedscreen said:
You may want to look on ebay for a Motorola Photon 4G / Droid 3 Battery Charger for a few bucks/no shipping cost. Order the charger, rush shipping if you feel you need to, open the package, take the battery out of your phone, plug the battery in the wall with the charger, and wait until the light changes from red to blue/green and continue from there.
Sent from my MB855 using xda premium
Click to expand...
Click to collapse
no other ways to get it to charge? tried to relock and ended up with this problem didnt realize mt phone was so low and now all i get is the failure to boot 4 starting rsd battery too low..... sucks to be me just got this phone through ebay so would have to pay the fee to get new one from insurance if i cant fnd a way to charge this thing really dont want to have to buy another battery or charger old lady already mad i got such a picey phone and screwed with it and screwed it up...ha ha oh well
I cut the end off of a charger stripped the red&black wires placed red on pos blk on neg of battery and plug into wall for about 20 min the battery started getting warm but this worked for me
Sent from my MB855 using XDA App
In rsdlite uncheck the delete on exit box. It will save your battery
Sent from my MB855 using XDA App
I thought if it was semi-bricked you could still charge it?
sbf update-failed to boot 2
Hey after doing OTA for latest sbf im getting error
failed to boot 2
starting RSD mode
and when i srestart my mopho is runs normally but after some time it restarts on its own and goes to above error message again
my battery is showing at 50% is that the reason
is there any other way to fix it??
Flash 154 then 198
dilkush said:
Hey after doing OTA for latest sbf im getting error
failed to boot 2
starting RSD mode
and when i srestart my mopho is runs normally but after some time it restarts on its own and goes to above error message again
my battery is showing at 50% is that the reason
is there any other way to fix it??
Click to expand...
Click to collapse
Sent from my MB855 using XDA App
still no luck
jokersax11 said:
Flash 154 then 198
Sent from my MB855 using XDA App
Click to expand...
Click to collapse
Hey it's showing that my version is 154 only....
also when i tries to connect to rsd lite it's showing unable to initialize from .INI file
can you post link for 198 update on xda forum link is not working
Loki is making a new guide thread with everything in it, ill oil the whip
dilkush said:
Hey it's showing that my version is 154 only....
also when i tries to connect to rsd lite it's showing unable to initialize from .INI file
can you post link for 198 update on xda forum link is not working
Click to expand...
Click to collapse
Sent from my MB855 using XDA App
Looks like it started working fine once i wiped my cache but at the same it it showed notification that update failed.....not worried about update failure as finally my mopho started working!!!!!!!!!!!!
I attempted to flash ICS onto my Razr Maxx, but the battery ended up dying. The only way to get the phone into a boot menu is to have a wall charger plugged in. I've done this, and selected "BP Tools," but it just stays on the Motorola icon for hours, never charging the phone. I also tried the "flash" option, and got the same result.
I can still enter into "recovery," and have tried throwing several different operating systems on the SD card. Every time I "update from .zip," the installation fails.
What can I do to charge the battery at this point? I don't have a factory cable, and don't understand why the BP Tools trick isn't working.
Try to boot normally while you are plugged in wall charger..!
And then charge it and flash it with RSD LITE with proper fastboot file I mean
check it properly that what region and gsm or cdma file is it, if u dont flash it properly it will show you validation error...
SLICED BY MY RAZR..
vikcie said:
Try to boot normally while you are plugged in wall charger..!
And then charge it and flash it with RSD LITE with proper fastboot file I mean
check it properly that what region and gsm or cdma file is it, if u dont flash it properly it will show you validation error...
SLICED BY MY RAZR..
Click to expand...
Click to collapse
As soon as I plug the phone in, it goes to the Motorola logo. When I enter fast boot mode, it says battery low. When I try to charge using BP Tools, it just stays on the Moto logo, never actually charging. It appears that I have no OS.
Since I can enter recovery, is there any zip file I can put on my sd card to load up an OS onto the phone?
Sent from my Galaxy Nexus using xda app-developers app
Similar Problem
Stockmoose16 said:
I attempted to flash ICS onto my Razr Maxx, but the battery ended up dying. The only way to get the phone into a boot menu is to have a wall charger plugged in. I've done this, and selected "BP Tools," but it just stays on the Motorola icon for hours, never charging the phone. I also tried the "flash" option, and got the same result.
I can still enter into "recovery," and have tried throwing several different operating systems on the SD card. Every time I "update from .zip," the installation fails.
What can I do to charge the battery at this point? I don't have a factory cable, and don't understand why the BP Tools trick isn't working.
Click to expand...
Click to collapse
I too am having the same problem. I am very inexperienced with the whole programming process, so a detailed step-by-step answer would be helpful. I just wanted some Ice Cream
Guys have you tried reset factory or wipe cache in recovery...?
If its not working man then you need a MOTOROLA FACTORY CABLE..
its very easy to make, I made one for myself and thts how I recovered my razr from this problem...
Best of guys..
sent through DFL AND FEDEX..
How do you make the cable? I've wiped cache and factory reset. That's not going to do anything since there's no OS.
Sent from my Galaxy Nexus using xda app-developers app
Is there any way to put a zipped OS on the sd card and then go into recovery and load it?
None of the charging hacks are working, and the only reasonable fix seems to be getting an OS on the phone.
Sent from my Galaxy Nexus using xda app-developers app
I got mine fixed* I took it to Verizon and played dumb. They replaced it free with a new RAZR. They said that it could have happened when the OTA update took place. Worth a shot Moose. Just play dumb :-D
Didn't work for me. I'd just like to know why the hacks aren't working.
Sent from my Galaxy Nexus using xda app-developers app
Stockmoose16 said:
Didn't work for me. I'd just like to know why the hacks aren't working.
Sent from my Galaxy Nexus using xda app-developers app
Click to expand...
Click to collapse
I learned that sometimes they work, sometimes they don't. I had a similar issue over the past few days. Ended up pulling the back cover off and just charging straight to the terminals, and it really was very simple.
bought the cable on ebay delivered for ten bucks. took a week to get here from China and then an evening to use Matt's droidrazr 1.7 option 1 to ready the phone to charge and flash. Spent days looking for a file to flash from the card and other alternatives.
Order the cable.:good:
My son was trying to put a different ROM on his phone and about half way through it crashed. The phone now just keeps rebooting.
Tried the Power on / Vol down to try to get to android recovery, but it just goes blank. All other options cause the phone to just reboot and I try again (like a fool).
Is there any hope for me to get this phone working or is it now a paperweight?
Let me know if you need more information. I will provide what I know.
Thanks,
Jim
coachnh said:
My son was trying to put a different ROM on his phone and about half way through it crashed. The phone now just keeps rebooting.
Tried the Power on / Vol down to try to get to android recovery, but it just goes blank. All other options cause the phone to just reboot and I try again (like a fool).
Is there any hope for me to get this phone working or is it now a paperweight?
Let me know if you need more information. I will provide what I know.
Thanks,
Jim
Click to expand...
Click to collapse
Sounds like a bootloop. Did you look here?
I've had this happen when I attempted to flash my Atrix with the battery less.than 50%.charged. I was able to get it to boot up (after flashing 2.3.4 sbf via RSD) but it just rebooted itself every 2 mins. My warranty was up but, I went on Motorola's website and after using their troubleshooter, they gave me a reference number and address to mail in my device for repair. In about a week I got the phone back. I think they gave me a different device because I can now run 1.6 GHz OC kernels without my phone overheating. Good luck......
Sent from my MB860 using xda premium
Hi there all...
I jus finished flashing my Atrix 4g that was AT&T, was a bit of a pain realy used to the HTC lol.
well any way my friend dicided that he would do the same thing and unlock his that he just bought
along with the lapdock :S thinks he is a falsh git......
today he came over to my place threw the phone and lapdock on my bed an said iff i can fix it i can have it
asked what was wrong told me he had a power outage during the boot loader unlock.
Okay on to the problem i have with this phone now.....
firstly. when i plug the thing in to charge it turns on an goes stight into boot loader RSD option then
tells me that there is no enough batt life to flash the phone.
i carnt get this phone to charge so that i can start to try an recover this thing.. seems like he got a partial flash
done as the OS has been wiped when you turn it on (or plug in power) it always says failed to load...
any one got any advice for me please
You have 2 atrixes, so just charge the battery with the other one.. then continue the unlocking bootloader process
Sent desde mi MB860
lol i thought of that to right after i made the post an my mate left with my Atrix lol
gave him mine as he had no mobile so that dun work
me an my bright idears
no one can help
You can make a "motorola factory cable" it lets you use the phone with or without the battery. Search it up in google and follow the instructions to make one... I made one & used it a couple of times...
Edit: Here are some guides:
http://forum.xda-developers.com/showthread.php?t=1077414
http://droidrazrroot.com/droid-razr-hacks/how-to-make-motorola-factory-cable/
Kewl beans
thanx loads mate
Syl said:
You can make a "motorola factory cable" it lets you use the phone with or without the battery. Search it up in google and follow the instructions to make one... I made one & used it a couple of times...
Edit: Here are some guides:
http://forum.xda-developers.com/showthread.php?t=1077414
http://droidrazrroot.com/droid-razr-hacks/how-to-make-motorola-factory-cable/
Click to expand...
Click to collapse
Okay thanx the cable worked as intened just what i needed.
okay having flash problems with this phone now :S not sure what to do the phone powers on with
SVF:105:1:2
Failed to boot 0X1000
no OS detected going in to RSD mode
this is fine i ca select the boot mode whith the loader but when i load the RSD lite flashing
program i load the 4547-fix-try2.sbf file i downloaded from a thred on teh forums.
i start the flash then it gets to part where is needs bypass mode it will not auto select the
bypass mode it needs, so i select it for the divice then after the BP mode it needs to returen to RSD
Mode however the divice does not reset this time so that i cannot reset the phone RSD mode and
thus the phone flashing fails......
is there any one that can offer me some advice on this as i carnt think or find a way arround this...
many thanx guys