Related
I purchased a new vent holder with a car charger, and it charges the phone up OK when it is off, but if it is on it says charging but does not actually charge. This is especially annoying with Satnav and after an hour or two the phone dies and I don't know where I am going!
Anyone know what causes this? I guess it can't provide enough power for the device, especially when using the internal GPS, but I think it doesn't even keep up with the device is just turned on.
I am getting another charger just in case, but never had the problem on my old Touch....
..
try -> start/settings/system tab/power/battery tab - uncheck the box "when the device is turned on...."
It isn't ticked...
..
try ticking it..
That will have the opposite effect, it charges fine when plugged into the wall, the problem is something to do with the car.
Does anyone use satnav on a touch HD and have it charge at the same time?
Well there could be one or two issues.
On the USB port there are four connections, a positive and a negative and two data pins. When you plug your Touch HD into a PC power is supplied down the power pins and after negotiating with the USB controller chip over the two data pins the phone will pull up-to 500mA from the power supply to run and charge the phone. This is so the USB port on the PC is not damaged by the phone overloading the power supply to the port.
Without the negotiation with the USB controller chip the device will only charge at 100mA.
But 500mA is not enough to charge the phone with everything running, you will need at least 1000mA to do that (1 Ampere). So that is what your wall charger pushes out. But how does the phone know it can charge at a higher rate? Well inside the charger the data pins on the USB connector are wired in a way that the phone 'sees' that a higher current is available, and pulls a higher charging current.
So what you need is a minimum current 1 Amp car charger. If you already have a 1 Amp then the chances are that is does not have the data pins connected properly and the phone will not draw the higher current, meaning it will only charge at 100mA.
Thanks, I am going to try another one and see if that helps, perhaps it is just faulty, otherwise I will check if it is 1Amp.
Cheers.
I contacted the seller and they sent me a new one, which works. So it turns it my charger was just faulty.
What's the rating of the new one? and where did you get it from. I bought a 2amp (supposedly) but it doesn't give me more than 500mA.
I've had this problem and it sucks! As I'm always out on the road. But I have found a few solutions. I purchased a mini usb charger from asda for £6. After adjusting the backlight to medium this charger seems to keep the power level the same as it was before you plugged it in, so It doesn't let the battery go flat. I've now learnt to keep a spare charged battery in the car just in case it fails.
So I'm coming from the Apple world and I love having the Atrix because I can just use any microUSB cable that is around. I have a question about using different chargers though. The charger that can with the phone is 5.1V at 850mA but I have some extra Motorola ones that are lying around that are only 5.0V at 550mA. Will using the other charger degrade the performance of the battery over time or will it just take longer to get a full charge?
Spacebob11 said:
So I'm coming from the Apple world and I love having the Atrix because I can just use any microUSB cable that is around. I have a question about using different chargers though. The charger that can with the phone is 5.1V at 850mA but I have some extra Motorola ones that are lying around that are only 5.0V at 550mA. Will using the other charger degrade the performance of the battery over time or will it just take longer to get a full charge?
Click to expand...
Click to collapse
Well it'll definitely take longer to charge but *could* cause problems in the battery. My guess is that it will judging by how others have had an "on and off" problem with lower-amperage chargers. Instead of just charging slowly the charging sort of stops and starts randomly. Leads to the assumption that the transformer in the phone itself is having trouble accepting the power. Constantly connecting and disconnecting power when charging a battery can have consequences later on.
Spacebob11 said:
So I'm coming from the Apple world and I love having the Atrix because I can just use any microUSB cable that is around. I have a question about using different chargers though. The charger that can with the phone is 5.1V at 850mA but I have some extra Motorola ones that are lying around that are only 5.0V at 550mA. Will using the other charger degrade the performance of the battery over time or will it just take longer to get a full charge?
Click to expand...
Click to collapse
The Atrix is really picky with the chargers. I recommend to use only the original charger or the chargers that came with the docks. People described the weirdest things from touchscreen problems to not charging at all. Charging via USB cable doesn't work either (or it is very slow), neither on the computer nor in the car.
mgymnop said:
The Atrix is really picky with the chargers. I recommend to use only the original charger or the chargers that came with the docks. People described the weirdest things from touchscreen problems to not charging at all. Charging via USB cable doesn't work either (or it is very slow), neither on the computer nor in the car.
Click to expand...
Click to collapse
In my opinion....
I wouldn't go as far to say "use only original chargers/Motorola chargers". The underlying issue is just like hotleadsingerguy said, lower-amperage chargers.
If you avoid these chargers, you should be fine. My Motorola Atrix charging brick/USB cable are still in their original packaging, inside the phone's box, tucked away in a cabinet.
At home, I have a few Blackberry MicroUSB chargers which I've used on my Captivate (not picky), and now they charge the Atrix without problems. They are 5.0V/700mA chargers.
At work, I pieced together some chargers from Monoprice, buying USB (female plug) power adapter with long USB -> MicroUSB cables. The power adapter from Monoprice is 5.0V/1000mA, and I use these chargers on my Atrix without a problem...and that's also using like 15 feet long cables.
Monoprice Power Adapter
http://www.monoprice.com/products/p...=10420&cs_id=1042001&p_id=6171&seq=1&format=2
Blackberry Charger
http://www.amazon.com/BlackBerry-Or...0UGC/ref=sr_1_1?ie=UTF8&qid=1299396971&sr=8-1
I'd probably say your 550mA charger is not going to cut it, since I've seen some other threads mentioning charging problems with ~500mA chargers.
Has anyone noticed that phone does not charge while using GPS. The charging indicator is on but when I look at the stats it says discharging at -450 mAh. Is this the way it is and if so, is there a fix? 1 hr 42 m with 73% display on battery use and 43% charge remaining, but was plugged in the entire time while driving under an hour home. I am using the same Motorola high performance charger that every other phone is charged fully even when using GPS.
are you absolutely sure the charger is giving the full 1A?
What sensor app are you using to see the battery discharging?
Mine charges normally with gps on.
Sent from my HTC
LTE 4G Rezound
I was curious so I tested this with "Battery Monitor" I have it plugged into my laptop currently which only gives +500mA. and not the +1A that you get from a wall/car/high power usb port.
the app is showing +257mA with GPS on and functioning normally.
So charging good here... Might be something with your motorola charger? It could have a sensor in it to detect 'trickle charging mode' that is improperly engaging when connected to the HTC causing the charger to put out a minimal 'sustain only' level of amperage.
good luck!
you need a charger putting out 1A ... most car chargers put out 500mA so find a good one off monoprice
Here's what I'm doing. I have a Belkin 2.1A(2100mAh) USB car charger dongle. The problem is, once i connect the USB cable to it the phone registers it as "Charging USB" and does notcharge anywhere near as fast(power-wise) as if the phone was registering it "Charging AC". I'm not keen on using a power inverter to get the full AC charge so instead i am going to go pick up a cheap micro USB cable, splice it open, then disconnect the data wires(green & white ones) & then tape it back up. By disconnecting the data wires, the phone will no longer think it's a USB connection and then charge via AC, getting the best charge possible.
that should work ^ if thats the problem
I've found that using the included USB cable with a Belkin dual port USB car charger allows the phone to charge as if it were plugged in to a wall. I'm guessing the included cable has a different layout than standard Micro USB cables.
Sent from my ADR6425LVW using xda premium
dawynkoop said:
I've found that using the included USB cable with a Belkin dual port USB car charger allows the phone to charge as if it were plugged in to a wall. I'm guessing the included cable has a different layout than standard Micro USB cables.
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
I'm guessing that I have the same belkin dual port (2.1amp and 1amp ports) and the best I've seen out of it is about 250mah charging. This is using the supplied usb/micro hdmi whatever cord for the phone.
I have seen discharge rates off the charger of 750mah which is the highest I've seen on any phone. I'm guessing if you are using the nav on your phone with the screen on, it will probably still be using battery while plugged in.
thatsricci said:
I was curious so I tested this with "Battery Monitor" I have it plugged into my laptop currently which only gives +500mA. and not the +1A that you get from a wall/car/high power usb port.
the app is showing +257mA with GPS on and functioning normally.
So charging good here... Might be something with your motorola charger? It could have a sensor in it to detect 'trickle charging mode' that is improperly engaging when connected to the HTC causing the charger to put out a minimal 'sustain only' level of amperage.
good luck!
Click to expand...
Click to collapse
Possible, but says AC charging in Battery Monitor widget. I will post a few pics.
Here are a few Pics. you can see a couple of things.
-Charger rated at 950 MA out. and no other phone I have owned lost a charge while driving including TBolt, Charge, Bionic.
-Shows as AC charging
- Spikes of good charging detected
Put on Normal power mode today on the way in. live wallpapers did not wrok, just flickered. 3G on vice 4G. Battery still went down, but above 90% on 40 minute drive in. Screen low but on. Bluetooth speaker.
Maybe it is the iBolt car mount. See review online. will try without dock this afternoon on my way home.
-----------------------------------------------------
User: marc frederick, Nov 25, 2011
Pros: Options for different backs
Cons: Does not charge the phone while it is in use
Try playing pandora when the phone is 100 charged. After 45 minutes on the car mount (and yes it is plugged into a charger and all indicatros show it is charging) and the charge level is 84. Using the same charger but plugged into the phone, playing Pandora for 45 min starting charge level 68. Ending charge level is 100.
Yeah, something is telling that charger to not give you full juice
Rezound
ok, drove home off the window mount and just on charger, all same except full brightness on screen.40 minute drive. came up 7% battery vice down from 100 to 43%. nedd a few trials to confirm, but looks like window mount is throttleing juice.
thatsricci said:
are you absolutely sure the charger is giving the full 1A?
What sensor app are you using to see the battery discharging?
Click to expand...
Click to collapse
i have seen spurts up to 913 with GPS off and screen just turned on. Using battery monitor widget. Not on window mount, just charger.
I can confirm. The car dock will not charge your phone atleast not with the screen on and nothing else running but battery monitor widget.
I bought one and tested it extensively yesterday. I used a Verizon 1a charger and a generic 1a charger. With the dock and both chargerz the phone DIScharged(as in LOST battery power) at between 100ma and 200ma. Without the dock using the same chargers and changing nothing on the phone the phone charged at between 50a and 300ma.
I did the test several times to eliminate any random things the phone may have been doing in the background.
After doing that controlled test I played with it some more and no matter what I did I could not get a positive charge with the dock attached even in airplane mode with the screen backlight at minimum. Without the dock using the same chargers i ran Pandora and a police scanner both outputting through the phone speaker, gps, wifi, mobile all on, and screen on auto and still had a very small positive charge.
Moral of the story DO NOT BUY THIS DOCK unless you dont mind it just being a piece of plastic that holds your phone in place.
I wonder if there's a quick mod to it to get it working right. Like the soldering of the USB chargers I've seen.
Rezound
I just went ahead and bought an extra battery so I wouldn't have to charge in the car. Only takes 20 seconds to pop in a new battery.
Can charge both batts while I sleep at night.
Sent from my Galaxy Tab 10.1
I was looking for a high current charger for my Android tablet and there was a review that talked about compatibility. Some of the high cap chargers appear to be designed for Apple products and the pin wiring is subtly different. So, on some non-Apple products, the charge is only recognized as a lower power, 500mah charger and the users reported that some devices would normally charge and others would not. Some of the dual port charges also split the power. The 2.1 amp port and the 1 amp port cannot be used at the same time, depending on what is plugged into them. This was also brand specific. I ordered the Amazon Basics 2.1 amp dual charger and will see how that works. I have noticed a difference in charge rates between my Motorola charger left over from the Blackberry and the Verizon OEM one. The VZW one is faster.
I do the same thing I have been doing since my Windows phone days.
I use the AC cord plugged into a 12v to AC adaptor(screen set to 100% bright and no timeout).
I drove 6 hours last week ruuning Google Maps/GPS & my battery was 100% charged when I got to my destination.
~John
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Slow Charge Message
arisch86 said:
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
Same here. Glad to hear it is not just me. I just got off with NA HTC Tech Support. There official stance is that they do not recommend or support using any device other than the official charging cable and plug in device. They went as far to say that they do not support charging in the car. I just about flipped my lid on the phone.
Here is the link to their site: http://www.htc.com/us/support/howto...783&p_name=droid-dna-by-htc-(verizon-wireless)
"Only the power adapter and USB cable provided in the box must be used to charge the battery"
I was told by Verizon that this was just a scare tactic, while HTC says I am not getting the right charge and they have no answer since they do not support DC charging in the car. Any info people have is appreciated. It works fine with Hard Wired DC -MicroUSB, but not with any USB Plug in.
Any apps that would help me measure the amount of charge it is getting?
Thanks in advance.
What are the specs on your car charger?
Sent from my HTC6435LVW using Xparent Red Tapatalk 2
So odd that they would do that, especially with the power draw of the phone. However you can charge using the battery packs?
My car adapter is a Macally USB car adapter model carusb10 output 5v/2.1 amp x1 500mA x2.
As for my house adapters the RCA 2 port USB wall adapter. 2.1 Amp x 1 or 1000mA x 2 I believe.
Sent from my HTC6435LVW using Tapatalk 2
Everyone with a stock DNA unplug your charger and flip it around. As in flip the prongs. It should give you this message even with the HTC supplied one. Or try this. When you use another charger and it gives you that message unplug it and flip it. It should straighten out. I dunno. Something about the way the power is drawn.
xcesivemastub8ah said:
Everyone with a stock DNA unplug your charger and flip it around. As in flip the prongs. It should give you this message even with the HTC supplied one. Or try this. When you use another charger and it gives you that message unplug it and flip it. It should straighten out. I dunno. Something about the way the power is drawn.
Click to expand...
Click to collapse
I have tried several different USB adaptors, from Razorfish(BestBuy), Belkin single USB input 2.1amp, innocell (RadioShack) dual SUB 3.1amp. Same problem on all.
On the other hand, any direct Wall connection with USB cable attached seems to work fine.
Also, I have the Motorola p4000 battery backup and when I plug that in, it also works fine and views it as AC.
Swapping the pins didn't work for me, same issue. Its a pita for me especially charging in the car because when using phone for navigation it charges so slow that it can't actually charge my phone and my battery decreases. I've went the route in the car I use my nexus 7 charger connected to an inverter.
Sent from my HTC6435LVW using Tapatalk 2
From my phone conversation with Seth from HTC Support, the slow charging warning is due to the update because the update incorporates the faster charging feature that qualcomm & htc have referenced too recently (can't remember what its actually called). The phone has a new type of charging setup that makes it charge faster than some other phones.
Unfortunately some chargers (wall/car) dont supply enough voltage to activate the charging feature so while the phone does charge fine (it charges at standard phone charge rate) it cannot charge at the faster rate due to the charger.
He states that this will not harm the phone and ther phone will charge fine and it a normal time. You can disregard the warning. For those that like the faster charge rate, you have to use the right charger/cable.
Before the update our phones were mostly charging at the slower rate and that's why most didn't see a warning unless the cable being used was below the standard rate of charge.
Hope this helps
arisch86 said:
Seems ever since I updated to the latest OTA update, if I plug my phone in on certain chargers I get a notification stating slow charging enabled please connect to your factory charger. Anyone else having this issue?
It seems to do it on any charger or 12volt car to USB adapter capable of outputting 2 to 2.1 amps
Stock ROM, rooted, unlocked, s-off
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
Why are there so many problems about this thing lately even me, I experience this most of the time
When I use the Best Buy 2.1 amp wall charger I still get the message.
I'll need to find my oem wall charger.
So far every one I have gives this message.
I haven't seen this message at all on any of my charges but I haven't charged in the car yet. My battery usually lasts for more than the while day so I just charge at night.
Sent from my HTC6435LVW using xda app-developers app
Well with the faster charging enabled it does charge pretty quick especially using my nexus 7 wall adapter, even with my Nokia Qi pad. But man that last percent takes a while.
As of now I'm using supercharged hatka ROM slim 3.0.3 and getting good battery life. Even in the middle of nowhere where 75% percent of the time when I'm in the plant its searching for signal. I'll leave work after 8 hours and still be at 60%
Guess you can say its the only negative I have for the phone. Trust me the battery life is much better in the plant then my old bionic. I use to have to change the standard battery after 4 or 5 hours as it was completely dead.
Sent from my HTC6435LVW using Tapatalk 2
Last night I received my daughters replacement Rezound from the warranty company. It came with a 1 amp wall charger.
I plugged it into my DNA and did not get the notice of slower charging and it charged quicker than I've ever seen it.
Too bad my 2.1 best buy one won't.
The quick charge capable chargers must output just slightly higher voltage to trigger the rapid charge mode.
I'll experiment some day and see.
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
I have the charger that came with the phone it it fully charges my DNA in 2 hours from 3%
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
I kinda figured it was something with the pins if I wasn't voltage offset.
I did find that one of my car chargers from best buy runs in quick charge. The cable I fixed, rather than using a usb cable in a slot on the charger.
The best number 2.1 amp wall charger uses a data type cable.
Maybe I'll check into shorting the pins on that sucker to get quick charge mode.
Funkertosh said:
This is a known issue. It all comes down to there being no set standard for USB charging. Android, apple, tablets, they all just seem to do their own thing.
The phone is checking the pins on the charger. If the data pins are shorted, then you get fast charging. If not, then it will default to the slower USB charging.
That last update that came through added that 'Slow Charge' warning. I saw it on my gf's DNA. My DNA is rooted and ROM'd so I don't have that. You can still check for the charging speed on a device by going to the Battery page in the settings. Up on top it with either say AC (which is fast) or USB (which is slow).
The supplied HTC wall chargers have the data pins shorted within them, so any regular USB cable will allow you to charge at the AC rate. You may remember some years ago there used to be Charging Only cables and they were regular USB cables that simply had the data pins shorted.
Most car chargers do not have data pins shorted. I have used a number of different ones from monoprice and none of them will charge at the AC rate.
There are videos on youtube showing how to open them up and solder the data pins. You can look for charging cables on amazon (but that seems lame), or you can find a car charger that just actually works.
There is a cheap Motorola charger on Amazon that will give you the fast AC charge.
https://www.amazon.com/dp/B000S5Q9CA/ref=as_li_ss_til?tag=funkertosh-20&camp=0&creative=0&linkCode=as4&creativeASIN=B000S5Q9CA&adid=131FS8N5R70JPV4QGDCV&
Click to expand...
Click to collapse
The phone is doing more than checking pins now. I have a 2.1 Amp dual charger with pins shorted and get the warning. It happily charged in AC mode before the update. The charger can also charge a nexus 10 at 2 Amps. I'm guessing the kernel devs will have to locate the source of the warning. I thought the resistance between the data pins might be the trigger, but there is no difference between the HTC charger and my dual charger. It does seem my car charger is unaffected.
I have found that to trick the phone into AC mode you have to short the the actual cable. Hence strip the insulation off the wires and short the data wires together. Has worked for me on all my chargers.
Sent from my HTC6435LVW using Tapatalk 2
This message does not have to do with the update. I have still not updated my DNA and have been struggling with this for about 6 or 8 months. I am on 2.08. The issue has continually gotten worse since the first time I saw it. At first it would just appear about 1 in 10 times I plugged it in to a car charger. It then got to the point where it would only not show the message with a certain car charger. Now it is showing it on the one car charger that works, but if I mess around with it and unplug and replug it a few times it will finally charge normally. The last few days it has started showing the message on the OEM charger. I have cleaned out the port on the phone and cables quite a few times now, but it doesn't help. I found that doing that only helps if it gets really full of lint and the cable rocks in the port causing it to loose connection if you move it, but it does not change the slow charging message at all. The phone is also definitely not charging at full speed when that message is shown. If I have it plugged in and it shows that message my battery actually drains if the screen is on. With the screen off I only gain about 10% per hour. I am not sure where the issue is, but I think it is different in different circumstances. In my case I think it is the phone itself, but from what I have read about others experiences it seems their problem might be the charger/cord. I hope this gets sorted out soon.
Clay333 said:
This message does not have to do with the update. I have still not updated my DNA and have been struggling with this for about 6 or 8 months. I am on 2.08. The issue has continually gotten worse since the first time I saw it. At first it would just appear about 1 in 10 times I plugged it in to a car charger. It then got to the point where it would only not show the message with a certain car charger. Now it is showing it on the one car charger that works, but if I mess around with it and unplug and replug it a few times it will finally charge normally. The last few days it has started showing the message on the OEM charger. I have cleaned out the port on the phone and cables quite a few times now, but it doesn't help. I found that doing that only helps if it gets really full of lint and the cable rocks in the port causing it to loose connection if you move it, but it does not change the slow charging message at all. The phone is also definitely not charging at full speed when that message is shown. If I have it plugged in and it shows that message my battery actually drains if the screen is on. With the screen off I only gain about 10% per hour. I am not sure where the issue is, but I think it is different in different circumstances. In my case I think it is the phone itself, but from what I have read about others experiences it seems their problem might be the charger/cord. I hope this gets sorted out soon.
Click to expand...
Click to collapse
It could be the charging equipment your phone or it could also be the power source not providing enough power to the device for it to charge fast so it charges slow.
Sent from my HTC6435LVW using XDA Premium 4 mobile app
I installed CurrentWidget and charged with the motorola brick and the stock cable. I switched the cable with this one 6ft ebay cable and the charge rate increased, from 1000-1400mA to 1800-2200mA. Switching back to the other cable gives me the same results. Anyone want to test this out?
are you talking about the turbo charger? a good wire and turbo charger should get you about 2200-2500 depending on your battery
alobear said:
are you talking about the turbo charger? a good wire and turbo charger should get you about 2200-2500 depending on your battery
Click to expand...
Click to collapse
Yes the included cable does not charge as fast as the random cable I have here. Try a different cable and see if CurrentWidget shows a higher charge rate.
Using Ampere.....turbo charger and cable gets me 2200 mA.....same for a Blackberry cable....
Others I have get significantly less.
I have a cable that charges at 2500mAh and one that won't go above 1200mAh. The factory one gives me 2500mAh and these were also observed at the use battery percentage on different occasions. I always check for fun and I'll post some pictures I took below.
I have read that the cable used will effect the charging current for more than the obvious reason of a different resistance. I've read that certain cables have pins wired/bridged together that allow for more current. On a side note I'm a little OCD and try to ONLY use the stock charger because I HAVE had other chargers ruin my battery in other phones (over a period of time).